Rate Contract for Supply and Installation of Open Gym Green Gym Equipments in Municipal Corporation of Delhi

Rate Contract for Supply & Installation of Open Gym (Green Gym) Equipments in Municipal Corporation of Delhi

SEATED PULLER /PULL CHAIR made from “C” Class G.I pipe. DIMENSIONS: - 1900mm (Length) x 740mm (Width) x 1920mm. (Height).SAFE AREA:- 1.2Mtr x 3Mtr. Seated puller equipment made up of “C” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The center pipe is of 100NB made from “C” Class G.I. pipe. Bottom support is of M.S. round plate of DIA 250 mm & 10mm thickness welded. All linkages are made up of 25NB “C” class G.I. pipe. The handle frame is of 32NB “C” class G.I. pipe. The seat frame is of 32NB “C” class G.I. pipe. To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class. Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation Cover Closing Cap is made from Injection Moulded Plastic LLDPE / HDPE. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.Closing Caps are made up of from Injection Moulded Plastic LLDPE / HDPE.Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. The bearings used are of “6205 2RS1” and “6203 2RS1” permanent lubricated sealed bearing of reputed brand.High tensile steel with galvanized nuts & bolts are used for assembly.Thecirclips used for assembly are of A16. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

CROSS TRAINER /ELLIPTICAL EXERCISER DIMENSIONS: - 1320mm (Length) x 600mm (Width) x 1750mm. (Height).SAFE AREA: - 1.77 x 1.2Mtr.Cross trainer equipment made from “C” Class G.I. Pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame Pipes are of 80NB “C” Class G.I. Pipe with single bend pipe with 250mm radius. The bottom support of M.S. round plate of DIA 250 mm & 10mm thick. The Handle Frame is made up of 25NB “C” Class G.I. Pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. To build structure bushes are used which are made from M.S. seamless pipe of 60mm OD With 5 mm thickness. The footrests are made from Injection Moulded Plastic LLDPE / HDPE. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. Pins used of Diameter 35mm, 25mm, and 17mm are made up from SAE 8620 bright .The Bearings used are of “6007 2RS1” “62052RS1” and “62032RS1” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). A16 , A 24 mm circlips are used for assembly. Bolt M8X16 mm and NY lock nut of M8 made of SS304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.

BACK EXTENSION DIMENSIONS: - 1400mm (Length) x 700mm (Width) x 820mm (Height).SAFE AREA: - 2.4Mtr x 1.7Mtr.Back Extension Equipment made from “C” class G.I. Pipe of different NB pipe. (NB stands for Nominal Bore i.e. Internal Diameter of pipe in mm) The main frame is of 50mm NB made from “c” Class G.I. pipe. The Foot resting frame of 32mm NB made from ”c” Class G.I. pipe. The handle frame is of 25NB made from “C” Class G.I. pipe. The seat fitted on the outer frames is made up of M.S. Sheet of size 330 mm X 300mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. The foundation used for fixing is consists of 50mm NB made from ”C” Class G.I. pipe.The footrests are made from Injection Moulded Plastic LLDPE / HDPE. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

SIT UP BOARD FOR USE OF TWO PERSONS AT ONE TIME. DIMENSIONS: - 1820mm (Length) x 430mm (Width) x 580mm (Height). Safe Area:- 2.8Mtr x 0.6Mtr. Sit up Board Equipment made from “C” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame is of 50mm NB made from “C” Class G.I. pipe in a single bend and supported with the MS round plate of DIA 250x10mm thickness. Fiber reinforced Plastic sheet of 3mm thickness is Bounded on 25mm NB (G.I.) “C” class pipe of main frame. The base support of the sit up board is made 40NB (G.I.) “C” class pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

STANDING SEATING TWISTER. DIMENSIONS: - 1700mm (Length) x 540mm (Width) x 1250mm. (Height).SAFE AREA: - 3 Mtr x 1Mtr.Seating & Standing Twister equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The Center Pipe is of 100mm NB made from “C” Class G.I. Round Pipe. The M.S. round plate of DIA 250 mm & 10mm thickness is welded at bottom. Handle and Bottom sleeve pipe of 125mm OD with thickness 5mm provided for easy assembly, replacement and maintenance. The bottom frame of the Seating & Standing twister is of 32 NB, 50 NB, and 25 NB made from “C” class G.I. pipe. The handle frame of Seating & Standing twister is 25 NB & Foot resting frame of seating side is made from “C” class G.I. pipe of 25mm NB.The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRCA square pipes of 3mm thickness. The Twister plate fitted on the bottom frame is made up of Injection Moulded Plastic LLDPE / HDPE and supported by M.S. Round Plate of size 300mm diameter&10mm thickness. Closing Caps are made up Injection Moulded Plastic LLDPE / HDPE. The Pins used are made up of DIA 35 mm SAE 8620 bright material. The bearings used are of “62052RS1” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

SKY WALKER DIMENSIONS: - 1720mm (Length) x 630mm (Width) x 1750mm.(Height). SAFE AREA: - 2.7Mtr x 1.6Mtr. Sky Walker Equipment made from “C” class G.I. Pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame pipe is of 80mm NB made from “C” Class G.I. Material which is bend at the radius of 250mm.The leg movement frame is of 50 x 50mm x 3mm thick CRC square pipe. Sleeves are made up of 100 mm OD M.S. pipe with thickness 5mm. This results in easy replacement of bearings, pins and handle The handle frame is of 25mm NB made from “C” Class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class. Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Two foundations are provided for rigid support. The footrests made from Injection Moulded Plastic LLDPE / HDPE. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. The pins used are made up of DIA 25mm SAE8620 bright material. Pins are fixed at the outer end with M8 grub screws and Dia.8mm SS ball. The bearings used are “62052RS1” are permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for assembly are of A24 type. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size).

CHEST PRESS . DIMENSIONS: - 2000mm (Length) x 710mm (Width) x 2200mm. (Height).SAFE AREA: - 3.0Mtr x 1.7Mtr.Chest press equipment made up of “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The center pipe is of 100NB made up of “C” Class G.I. pipe. The bottom welded with support of M.S. round plate of DIA 250 mm & 10mm thickness. The connecting pipes are made up from 25NB “C” class G.I. pipe. The handle frame is made up from 32NB “C” class G.I. pipe. To build structure bushes are used which are made from MS seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class. Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. Foundation cover Closing Cap is made from Injection Moulded Plastic LLDPE / HDPE. Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The bearings used are of “62052RS1” &“62032RS1” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for locking is made up of A24 mm & A16mm. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size).

HORSE RIDER DIMENSIONS: - 1180mm (Length) x 400mm (Width) x 1400mm. (Height). SAFE AREA: - 2.2Mtr x 1.4Mtr.Horse rider equipment made from “C” class G.I. Pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame of 100NB made from “C” Class G.I. pipes welded with M.S. round plate of DIA 250 mm & 10mm thick. Seat provided are made up of MS deep draw quantity of 2mm thickness with no joint with Uniform outer edge radius 20mm. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The leg movement frame is of 32NB made from “C” G.I. pipe. The handle frame is of 32 NB made from “C” Class G.I. pipe. The footrests are made from 25 NB “C” class G.I. pipe. Pins used of Diameter 17 mm are made up from SAE 8620 bright material. N The bearings used of “62032RS1” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts for assembly. The serclips used for assembly are of A24 mm. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size).

ROWER (DIMENSIONS: - 1200mm (Length) x 1000mm (Width) x 920mm. (Height).SAFE AREA: - 1.5Mtr. x 1.5Mtr. Rower Equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.The Main frame is of 80NB “C” class G.I. Pipe welded with M.S. round plate of 250mmX10mm. The handle frame 25NB is made from “C” class G.I. pipe.The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. To join the movement frame to main frame connecting links made up from 32 NB G.I. “C” class pipe. The seat fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300mmX2mm thickness and deep drawn and pressed tools and dies to have uniform radius of 20 mm with no sharp edges. Pins used of Diameter 17mm are made up from SAE 8620 bright material. The bearings used are of “6203zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The P.U. bushes (Stopper) used to avoid the collision. The circlips used for assembly is of A 16. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embEded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

TAICHI SPINNER ( DIMENSIONS: - 700mm (Length) x 1000mm (Width) x 1280mm (Height). Safe Area:- 1.9Mtr X 1.9Mtr Thaichi spinner Equipment made up of “C” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The center pipe is of 100NB made up of “C” Class G.I. pipe. The handle movement round frame is made up from 25 NB “C” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB“C” class Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. The pins used are made up of DIA 25 mm of SAE8620 bright material. The bearing used is “62012RS1” & “62052RS1” permanent lubricated sealed bearing of reputed brand. High tensile S.S. nut bolts are used for assembly. Foundation cover Closing Cap is made of Injection Moulded Plastic LLDPE / HDPE. The cerclips used for assembly is of A24 and A11.The nylon bush is used for handle knob. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.

ARM AND PADDLE BIKE (DIMENSIONS: - - 1100mm (Length) x 500mm (Width) x 900mm (Height). SAFE AREA: - 2000mm (Length)X1000mm(Width). Arm and Paddle Bike made from “C” Class GI Pipe. The Center Pipe is of 40mm NB made from “C” Class GI Pipe. The Handles is made up of casted iron material with plastic holding grips. For foundation hole pass provision is provided. The footrests is made from Aluminum casting material, its sizes are 130 mm X 300 mm & 3 mm thickness. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. The Pins used is made up of 25 mm diameter Harden low carbon steel. The Bearings used is of “6205” permanent lubricated sealed bearing. The Nut Bolts used for assembly are made from S.S. material. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size).

AIR WALKER Providing and fixing Air Walker made from “C” class GI Pipe. The center pipe is of 80mm NB made from “C” Class MS pipe, 32mm NB:- Air Walker pedal frame duly bend, 25mm NB:- Air Walker handle frame duly bend and the bottom support of M.S. round plate of 250 mm dia& 10mm thickness is welded at bottom. MS plate of 245 x 113 x 2.8mm :- Footrest support plate. The leg movement frame is of 40mm NB made from “C” Class MS pipe. The handle frame is of 25mm NB made from “C” Class GI pipe. The foundation used for fixing is consists of three equal items i.e. 80mm NB made from “C” Class GI pipe, M.S. Round Plate of 250 mm dia& 10mm thickness & 25 mm X 25mm M.S. angle of 3 mm thickness. MS pipe 48 x 48 x 2.8mm:- Footrest frame support. MS Angle 23 x 23 x 1.8mm:- Foundation support frame. MS Flat 48 x 9mm:- Foundation plate support. MS bright material:- Pins made of Dia.25mm. MS plate of 8mm:- Air Walker Pedal L-bend, support. 60mm dia seamless pipe:- Bushes. Bearings:- Permanent lubricated bearings 6205. Closing Caps made from top quality FRP material with 2 mm thickness. HDPE / LLDPE Plastic :- Closing cap, Air Walker Footrest. The pins used are made up of 25mm diameter bright bar. The bearings used be permanent lubricated sealed bearing of reputed make. The nut bolts used for assembly are made from S.S. material. The serclips used for assembly are of 25 mm diameter. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

Providing and fixing Surf Board made from “C” Class GI pipe. The center pipe is of 100mm NB made from “C” class GI pipe, and the bottom support of M.S. plate of 250 mm dia& 10mm thickness is welded at bottom. The handle frame is of 40mm NB & 25mm NB made from “C” class GI pipe. The movement frame is made up of 50mm NB “C” class GI pipe. The foundation used for fixing consists of three equal items i.e. 100mm NB made from “C” Class GI pipe, M.S. round plate of 250 mm diameter & 10mm thickness, 25mm X 25mm X 3mm M.S. angle. To join the centre pipe & handle frame seamless pipe of 130mm dia& 3mm thickness is used. For the movement, bushes are used & for it 60mm dia with 3mm thickness & 60mm solid bar is used. The footrests is made from FRP/C.I./Aluminum casting material, its sizes are 320 mm X 270 mm & 5 mm thickness. For support of footrest is 200mm X 250mm with 5mm thickness M.S. Plate and 50mm X 50mm CRC Square pipe with 2mm thickness is used. Closing Caps made from top quality FRP material which is of 2 mm thickness. The pins used are made up of 25 mm diameter Harden bright bar. The bearing used be permanent lubricated sealed bearing of reputed make. The handles used are of Rubber grip. The Nut Bolts used for assembly is made from S.S. material. The bushes (Stopper) used to avoid the collusion made from Poly Urethin Plastic material of 50 mm dia. The serclips used for assembly is of 25 mm dia. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size).

TRIPPLE TWISTER STANDINGDIMENSIONS: - 1150mm (Length) x 1150mm (Width) x 1580mm. (Height). SAFE AREA: - DIA 2.1Mtr.Triple Twister made from “C” Class Galvanized Iron (G.I.) Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The Center Pipe is of 100NB made from or “C” Class G.I. Round Pipe. The bottom support welded is of M.S. round plate of DIA 250 mm & 10mm thick. The standing frame is of 32NB made from “C” class G.I. pipe. The handle frame of triple twister is of 25 mm NB made from or “C” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80mm NB or “c” class welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness The standing plate is fitted on the frame made up of DIA 80mm seamless pipe. M.S. Round Plate of size DIA 300mm x 10mm thickness. Closing caps of top quality Fiber reinforced Plastic material which is of 2 mm thick. The Pins used are made up of DIA 25 mm SAE8620 bright material. The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand (FAG/SKF). High tensile steel with galvanized nuts & bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

DOUBLE TWISTER (DIMENSIONS: - 1700mm (Length) x 540mm (Width) x 1250mm. (Height). SAFE AREA: - 3 Mtr x 1Mtr. Double Twister equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimetres. The Center Pipe is of 100mm NB made from “C” Class G.I. Round Pipe. The M.S. round plate of DIA 250 mm & 10mm thickness is welded at bottom. The standing frame of the Double twister is of 32 NB made from “C” class G.I. pipe. The handle frame of double twister is 25 NB. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The Twister plate fitted on the standing frame is made up of M.S. Round Plate of size 300mm diameter and 10mm thickness. Closing caps made from top quality Fiber reinforced Plastic material which is of 2 mm thick. The Pins used are made up of DIA 25 mm MS bright material. The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

SEATED TWISTER THREE IN ONE (DIMENSIONS: - 1150mm (Length) x 1150mm (Width) x 1300mm (Height). SAFE AREA: - 2Mtr x 2Mtr. Seated Twister Equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The Center Pipe is of 80 NB made from “C” Class G.I. Pipe. The chair Pipe is of 50 NB made from “C” Class G.I. Pipe. The M.S. round plate of DIA 250 mm & 10mm thickness is welded at bottom. The supporting frame of the seated twister is of 32 NB made from “C” class G.I. pipe. The handle frame of seated twister is of 25 mm NB made from “C” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The twister plate is fitted on the supporting frame is made up of 60NB seamless pipe. DIA 300mm x 10mm thickness M.S. Round Plate. Closing caps made from top quality Fiber reinforced Plastic material which is of 2 mm thickness. The bearings used be permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

SHOULDER BUILDERProviding and fixing Shoulder Builder made from C- Class GI pipe. The Center Pipe is of 100mm NB made from “C” Class GI pipe, and the bottom support of M.S. Round plate of 250 mm diameter & 10mm thickness is welded at bottom. The handle movement frame is of 25 NB & 20 NB made from “C” Class GI pipe. To Join the centre pipe & handle movement frame seamless pipe of 130mm dia& 3mm thickness is used. The foundation used for fixing consists of three equal items i.e. 100mm NB made from “C” class GI Pipe, M.S. Round Plate of 250 mm dia& 10mm thickness & 25 mm X 25mm X 3mm M.S. angle. Closing caps made from top quality FRP material which is of 2 mm thickness. The pins used are made up of 25 mm dia bright bar. The bearing used be permanent lubricated sealed bearing of reputed make. The nut bolts used for assembly are made from S.S. material. The serclips used for assembly is of 25 mm diameter. The Poly Urethin plastic bush is used for handling. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

COMBINATION SET (3 IN ONE) OF AIR WALKER + LEG PRESS + SHOULDER BUILDER (DIMENSIONS: - 2150mm (Length) x 950mm (Width) x 1600mm.(Height). Safe Area:- 3.0 Mtr x2.0Mtr. Air Walker cum leg press cum shoulder builder Equipment made from “C” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame is of 100 NB made from “C” Class GI Pipe. The bottom support frame of M.S. 40mm x 75mm x 3mm thick C Channel. seat fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300mmX2mm thickness and deep drawn and pressed tools and dies to have uniform radius of 20 mm with no sharp edges. The bottom support frame of M.S. 40mm x80mmx3mm thick rectangular pipe. The leg movement frame is of 32NB made from “C” Class G.I. pipe. The handle frame is of 25NB made from “C” Class G.I. pipe. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. Pins used of Diameter 25mm are made up from SAE 8620 bright material. Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The bearings be used permanent lubricated sealed bearing of reputed make brand. High tensile steel galvanized nuts & bolts are used for assembly.A24 mm circlips are used for assembly.25 NB G.I. pipe is used for rotary ring of Shoulder Builder. The footrests are made from Injection Moulded Plastic LLDPE / HDPE, With the support of 310mm X 130mm X 3mm thick MS plate. Equipment has Bolting provision for mounting on concrete slab. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size).

COMBINATION AIR WALKER + LEG PRESS + SEATING TWISTER (DIMENSIONS: - 2300mm (Length) x 860mm (Width) x 1600mm.(Height). Safe Area:- 1.39 x 1.27Mtr. Air Walker cum leg press cum seating twister Equipment made from “C” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame of 100NB made from “C” Class G.I. pipe. The bottom support frame of GI 40mm x80mmx3mm thick rectangular pipe. The leg movement frame is of 32NB made from “B” or “C” Class G.I. pipe. The handle frame is of 25NB made from “C” Class G.I. pipe. Closing Caps made from top quality Fiber reinforced Plastic material with 2 mm thickness. Pins used of Diameter 25mm are made up from SAE 8620 bright material. The bearings be used permanent lubricated sealed bearing of reputed make brand. High tensile steel galvanized nuts & bolts are used for assembly.DIA 25 mm cerclips are used for assembly. 300mm diameter x 10mm thick plate can be used for rotating seat of seating twister with 50NB vertical G.I. pipe. The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 310mm X 130mm X 3mm thick MS plate. It has Bolting provision for mounting on concrete slab. To build structure bushes are used which are made from seamless pipe of 50mm O.D. And 6mm thickness as well as 50mm diameter solid bar is used. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

COMBINATION AIR WALKER + LEG PRESS + STANDING TWISTER (DIMENSIONS:- 2250mm (Length)x 860mm (Width) x 1600mm.(Height). SafeArea:-3.0Mtrx1.8Mtr. AirWalker cum leg press cum standing twister Equipment madefrom “C”classG.I.Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Themainframeof100NB madefrom“C”ClassG.I.pipe. Thebottomsupport frame of thick rectangular pipe.Thelegmovementframeis of32NB madefrom“C”ClassG.I.pipe.Thehandleframeis of25NB madefrom“C”ClassG.I.pipe. ClosingCapsmadefromtopqualityFiber reinforced Plasticmaterialwith2mmthickness.Pinsused of Diameter 25mmaremadeupfrom bright material. Thebearingsusedbepermanentlubricatedsealedbearingof reputedbrand(SKF/FAG). Hightensilesteelgalvanizednuts&boltsareusedforassembly. DIA 25mmcerclips are usedforassembly. 300mm diameter x 10mm thick plate can be used for rotating seat of standing twister with 50NB vertical G.I. pipe. The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 310mm X 130mm X 3mm thick MS plate. It has Bolting provision for mounting on concrete slab. To build structure bushes areusedwhicharemade fromseamlesspipe of 50mm O.D. And 6mmthickness as well as 50mm diametersolidbarisused. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

DOUBLE PULL DOWN (DIMENSIONS: - 1200 MM (length) x 750 MM (width) x 2000 MM (Height). Double Pull Down is made from “C” Class GI-pipe. The center pipe is of 100mm NB made from “C” Class GI-pipe, and the bottom support is of MS round plate of 250mm Dia& 10mm thick is welded at the bottom of the pipe. The remaining frame is made of 32mm NB & 50mm NB “C” Class GI-pipe. The handle frame is made of 32mm NB & 25mm NB “C” Class GI-pipe. Middle support is of 25mm NB “C” Class GI-pipe. Lower frame is made of 32mm NB & 25mm NB “C” Class GI-pipe. For the assembly different bushes are used which is made from 60mm with 3mm thick seamless pipe is used. The foundation used for fixing it consist of three equal items i.e 80mm NB made from “C” class GI-pipe, MS round plate of 250mm Dia&10mm thick, 25mmx25mmx3mm MS angle. Closing caps are made from top quality LLDPE Material which is of 2mm thick. The pins used are made up of 25mm & 17mm dia Solid bar. The bearings used are of “6205 & 6203” permanent lubricated sealed bearing of reputed make. The nut Bolts used for assembly are made from SS material.High tensile steel with galvanized nuts & bolts are used for assembly. The circlips used for assembly is made up of 25mm & 17mm dia. The foundation pipes are embedded in CC stock and painting is done by attractive color spraying after proper surface treatment, the initial coat of primer surface is applied before top coat. The powder coating is done from Poly Rethane& Epoxy Powder with 60 to 70 Micron Thickness.The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

TRICEPS PULLER (DIMEMSIONS:- 2110MM (Length) x 600MM (Width) x 1600MM (Height) Triceps Puller is made from “C” Class GI-pipe. The center pipe is of 100mm NB made from “C” Class GI-pipe, and the bottom support is of MS round plate of 250mm Dia& 10mm thick is welded at the bottom of the pipe. The remaining frame is made of 32mm NB “C” Class GI-pipe. The handle frame is made of 32mm NB & 25mm NB “C” Class GI-pipe. The seat frame is of 32mm NB “C” Class GI-pipe. For the assembly different bushes are used which is made from 60mm with 3mm thick seamless pipe is used. The foundation used for fixing it consist of three equal items i.e 80mm NB made from “C” class GI-pipe, MS round plate of 250mm dia& 10mm thick, 25mmx25mmx3mm MS angle. Closing caps are made from top quality LLDPE Material which is of 2mm thick. The pins used are made up of 25mm & 17mm dia Solid bar. The bearings used are of “6205 & 6203” permanent lubricated sealed bearing of reputed make. The nut Bolts used for assembly are made from SS material. The circlip used for assembly is made up of 25mm & 17mm dia.High tensile steel with galvanized nuts & bolts are used for assembly. The foundation pipes are embedded in CC stock and painting is done by attractive color spraying after proper surface treatment, the initial coat of primer surface is applied before top coat. The powder coating is done from Poly Rethane& Epoxy Powder with 60 to 70 Micron Thickness.The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

SINGLE SKYWALKER (DIMEMSIONS:- 1850MM (Length) x 520MM (Width) x 1780MM (Height). Single Skywalker is made from “C” Class GI-pipe. The center pipe is of 50mm NB made from “C” Class GI-pipe, and the bottom support is of MS round plate of 250mm Dia& 10mm thick is welded at the bottom of the pipe. The remaining frame is made of 50mm NB “C” Class GI-pipe. The handle frame is made of 25mm NB& 32mm NB “C” Class GI-pipe. Middle support is of 40mm NB “C” Class GI-pipe. Lower frame is made of 32mm NB “C” Class GI-pipe. For the assembly different bushes are used which is made from 60mm with 3mm thick seamless pipe is used. The foundation used for fixing it consist of three equal items i.e 80mm NB made from “C” class GI-pipe, MS round plate of 250mm dia& 10mm thick, 25mmx25mmx3mm MS angle. Closing caps are made from top quality LLDPE Material which is of 2mm thick. The circlips used for assembly are made up of 25mm dia. The pins used are made up of 25mm dia Solid bar. The bearings used are of “6205& 6203 permanent lubricated sealed bearing of reputed make. The nut Bolts used for assembly are made from SS material.High tensile steel with galvanized nuts & bolts are used for assembly The foundation pipes are embedded in CC stock and painting is done by attractive color spraying after proper surface treatment, the initial coat of primer surface is applied before top coat. The powder coating is done from Poly Rethane& Epoxy Powder with 60 to 70 Micron Thickness.The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

LEG PRESS Leg Press is made from “C” Class GI-pipe. The center pipe is of 100mm NB made from “C” Class GI-pipe, and the bottom support is of MS round plate of 250mm Dia& 10mm thick is welded at the bottom of the pipe. The remaining frame is made of 32mm NB “C” Class GI-pipe. The handle frame is made of 25mm NB “C” Class GI-pipe. Middle support is of 25mm NB “C” Class GI-pipe. Lower frame is made of 32mm NB “C” Class GI-pipe. For the assembly different bushes are used which is made from 60mm with 3mm thick seamless pipe is used. The foundation used for fixing it consist of three equal items i.e 80mm NB made from “C” class GI-pipe, MS round plate of 250mm dia& 10mm thick, 25mmx25mmx3mm MS angle. Closing caps are made from top quality LLDPE Material which is of 2mm thick. The pins used are made up of 25mm dia Solid bar. The bearings used are of “6205 permanent lubricated sealed bearing of reputed make. The nut Bolts used for assembly are made from SS material.High tensile steel with galvanized nuts & bolts are used for assembly. The circlips used for assembly are made up of 25mm dia. The foundation pipes are embedded in CC stock and painting is done by attractive color spraying after proper surface treatment, the initial coat of primer surface is applied before top coat. The powder coating is done from Poly Rethane& Epoxy Powder with 60 to 70 Micron Thickness.The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

Providing and fixing Test RIG manufactured by combination of anti-corrosive treated. Mild steel and all-season artificial wood to seek eco-friendly greenery effect. Dimensions: (L X W X H) = 3650X2300X2220 mm. Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece. Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000. All round pipes should be of “heavy grade" as per IS 1239 (Highest thickness as per IS 1239). Main Frame - Consist –. 90X90x3mm Thickness Square Tube get maximum internal strength to structure. All profiles used are of MS sheet of 8mm thick and duly cut on laser cutting machine with no sharp edge and sharp bend. All accessories should be demountable type. All Handle Demountable Type – 32 NB Heavy grade GI pipe Attached 5 mm thick MS Plate for Demountable system Nut & Bolts - All Nut & Bolt made from Stainless Steel. Foundation stool: Made from main pipe 90x90x3mm pipe and top support of M.S. plate of 250X250mm Square 10mm thickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm. All pillars should have provision of square plate 250x250x10 mm for mounting on foundation stool. Rig consist of 1 horizontal bar , 2 double bar , push up handles, 1 leg raise , 1 monkey bar and 2 chin up handles. Chin up should have leg resting support to be made of 40x40 MS pipe and covered with 1.5mm thick SS304 checker plate to avoid paint damages. Leg raise handle should have hand grip made up of SS304 material. Foundation stool design suitable to application and is embedded in C.C. 3:2:1 stock below ground level. Powder coating: - The powders to be used of pure polyester material of Reputed make with 70 to 90 micron thickness. Pre-treated with primary coat of 40 microns of etch primer which is specially developed for GI material. Instruction sticker for all uses of size 90mm x 160mm of SS 304 rustproof grade plate with 0.8mm thickness duly laser marked printing & riveted on 5mm thick MS plate. Avoided plastic and printed stickers to have lifelong durability. Safety & Maintenance:-All equipment should be tested as per EN16630 safety norms and carries CE mark. Maintenance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user up to 150Kg. User manual with trouble shooting guide should be available and supply with the equipment. Display for how to use, Do and Don’ts and contact details for maintenance and grievance redressal should be available on site.

Providing and fixing EXERCISE CYCLE manufactured with G.I. pipes of different N.B. N.B. Satnds for nominal bore size which is the internal diameter size of pipe as per is 1239 with heavy grade. Dimensions: (L X W X H) = 1660X150X1400mm. Main Frame is the combination of 90X90x3mm Thickness Square Tube, 80 & 50 NB GI pipe heavy grade to get maximum internal strength to structure. All round pipes should be of “heavy grade" as per IS 1239 (Highest thickness as per IS 1239). Both wheels of cycle made from 80 NB GI pipe heavy grade duly bend on cnc pipe bending machine. Handle 25NB Heavy grade GI pipe. Closing Caps- All closing caps made from Stainless Steel 304 of 0.7 mm thick duly pressed in dies and tools. Foundation stool: Made from main pipe 90x90x3mm pipe and top support of M.S. plate of 250X250mm Square 10mm thickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm. Foundation plate –M.S. 250X250mm Square with 10mm thick. 6205 bearing is being used of reputed brands like SKF. Pedal mounting plate to be made up of 8mm thick MS sheet. Seat for the cycle should be made of PPCP material. Seat supporting plate must have 5mm thickness. Foundation stool design suitable to application and is embedded in C.C. 3:2:1 stock below ground level. Hardware Nut & Bolts- Stainless Steel. Pin’s – Ø 25mm SAE 8620 duly case hardened and centerless grinded. Circlips– A 24 circlips are used for assembly. Bearing bushes– Ø 60mm OD provided with provision rubber seal at both sides to prevent bearings from environmental effects. Material used seamless pipe. der coating: - The powders to be used of pure polyester material of Reputed make with 70 to 90 micron thickness. Pre-treated with primary coat of 40 microns of etch primer which is specially developed for GI material. All MS material pretreated with anti-corrosive treatment including hot dip zinc plating. Instruction sticker of size 90mm x 160mm of SS 304 rustproof grade plate with 0.8mm thickness duly laser marked printing & riveted on 5mm thick MS plate. Avoided plastic and printed stickers to have lifelong durability. Safety & Maintenance:-All equipment should be tested as per EN16630 safety norms and carries CE mark. Maintenance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user up to 150Kg. User manual with trouble shooting guide should be available and supply with the equipment. Display for how to use, Do and Don’ts and contact details for maintenance and grievance redressal should be available on site.

Providing and fixing ‘Leg stretching’ manufactured by combination of mild steel and all-season artificial wood to seek eco-friendly greenery effect. Dimensions: (L X W X H) = 640X640X1200mm. Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece. Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000. All round pipes should be of “heavy grade" as per IS 1239 (Highest thickness as per IS 1239). Main Frame - Consist – 90X90x3mm Thickness Square Tube get maximum internal strength to structure. Leg Stretching Frame- made by 32 NB Heavy grade GI pipe Duly Bend. Attached 5 mm thick MS. Plate for Demountable system. Main Pipe Top Closing caps- Decent Design Size 120X120 SS304 Material. Nut & Bolts Closing Caps- All Nut & Bolt closing caps made from SS304 of 0.7 mm thick duly pressed in dies and tools. Foundation stool: Made from main pipe 90x90x3mm pipe and top support of M.S. plate of 250X250mm Square 10mm thickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm. Main Frame Foundation plate –M.S 250X250mm Square with 10mm thick. Foundation stool is embedded in C.C.3:2:1 stock below ground level. Powder coating: - The powders to be used of pure polyester material of Reputed make with 70 to 90 micron thickness. Pre-treated with primary coat of 40 microns of etch primer which is specially developed for GI material. Instruction sticker of size 90mm x 160mm of SS 304 rustproof grade plate with 0.8mm thickness duly laser marked printing & riveted on 5mm thick MS plate. Avoided plastic and printed stickers to have lifelong durability. Safety & Maintenance:-All equipment should be tested as per EN16630 safety norms and carries CE mark. Maintenance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user up to 150Kg. User manual with trouble shooting guide should be available and supply with the equipment. Display for how to use, Do and Don’ts and contact details for maintenance and grievance redressal should be available on site.

Providing and fixing ‘Push Up Bar’ manufactured by combination of mild steel and all-season artificial wood to seek eco-friendly greenery effect. Dimensions: (L X W X H) = 1000X850X1600mm. Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece. Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000. All round pipes should be of “heavy grade" as per IS 1239 (Highest thickness as per IS 1239). Main Frame - Consist –. 90X90x3mm Thickness Square Tube get maximum internal strength to structure. Push up Bar Hand Rail- 32 NB Heavy grade GI pipe. Duly Bend. Attached 5 mm thick MS Plate for Demountable system. Main Pipe Top Closing caps- Decent Design Size 120X120 SS304 Material. Nut & Bolts- All Nut & Bolt made from SS. Foundation stool: Made from main pipe 90x90x3mm pipe and top support of M.S. plate of 250X250mm Square 10mm thickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm. Main Frame Foundation plate –M.S 250X250mm Square with 10mm thick. Foundation stool is embedded in C.C.3:2:1 stock below ground level. Powder coating: - The powders to be used of pure polyester material of Reputed make with 70 to 90 micron thickness. Pre-treated with primary coat of 40 microns of etch primer which is specially developed for GI material. Instruction sticker of size 90mm x 160mm of SS 304 rustproof grade plate with 0.8mm thickness duly laser marked printing & riveted on 5mm thick MS plate. Avoided plastic and printed stickers to have lifelong durability. Safety & Maintenance:-All equipment should be tested as per EN16630 safety norms and carries CE mark. Maintenance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user up to 150Kg. User manual with trouble shooting guide should be available and supply with the equipment. Display for how to use, Do and Don’ts and contact details for maintenance and grievance redressal should be available on site.

Providing and fixing ‘Double Bar’ manufactured by combination of mild steel and all-season artificial wood to seek eco-friendly greenery effect. Dimensions: (L X W X H) 2900X250X1800mm. Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single ece. Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000. All round pipes should be of “heavy grade" as per IS 1239 (Highest thickness as per IS 1239). Main Frame - Consist – 90X90x3mm Thickness Square Tube get maximum internal strength to structure. Double Bar Hand Rail Pipe- 32 NB Heavy grade GI pipe. Main Pipe Top Closing caps- Decent Design Size 120X120 SS304 Material. Nut & Bolts- All Nut & Bolt made from SS. Foundation stool: Made from main pipe 90x90x3mm pipe and top support of M.S. plate of 250X250mm Square 10mm thickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm. Foundation plate –M.S 250mm Square with 10mm thick. Foundation stool is embedded in C.C. 3:2:1 stock below ground level. Powder coating: - The powders to be used of pure polyester material of Reputed make with 70 to 90 micron thickness. Pre-treated with primary coat of 40 microns of etch primer which is specially developed for GI material. Instruction sticker of size 90mm x 160mm of SS 304 rustproof grade plate with 0.8mm thickness duly laser marked printing & riveted on 5mm thick MS plate. Avoided plastic and printed stickers to have lifelong durability. Safety & Maintenance:-All equipment should be tested as per EN16630 safety norms and carries CE mark. Maintenance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user up to 150Kg. User manual with trouble shooting guide should be available and supply with the equipment. Display for how to use, Do and Don’ts and contact details for maintenance and grievance redressal should be available on site.

Providing and fixing ‘Horizontal Bar’ manufactured by combination of mild steel and all- season artificial wood to seek eco-friendly greenery effect. Dimensions: (L X W X H) 2330X250X1800mm. Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece.Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000. All round pipes should be of “heavy grade" as per IS 1239 (Highest thickness as per IS 1239) Main Frame - Consist – 90X90x3mm Thickness Square Tube get maximum internal strength to structure.Horizontal Bar Hand Rail Pipe- 32 NB Heavy Grade GI pipe Main Pipe Top Closing caps- Decent Design Size 120X120 SS304 Material. Nut & Bolts- All Nut & Bolt made from SS. Foundation stool: Made from main pipe 90x90x3mm pipe and top support of M.S. plate of 250X250mm Square 10mm thickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm. Foundation plate made up of M.S 250X250mm Square With 10mm thick.Total 02 foundation stools are to be used. Foundation stool is embedded in C.C. 3:2:1 stock below ground level.Powder coating: - The powders to be used of pure polyester material of Reputed make with 70 to 90 micron thickness. Pre-treated with primary coat of 40 microns of etch primer which is specially developed for GI material. Instruction sticker of size 90mm x 160mm of SS 304 rustproof grade plate with 0.8mm thickness duly laser marked printing & riveted on 5mm thick MS plate. Avoided plastic and printed stickers to have lifelong durability. Safety & Maintenance:-All equipment should be tested as per EN16630 safety norms and carries CE mark. Maintenance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user up to 150Kg.User manual with trouble shooting guide should be available and supply with the equipment. Display for how to use, Do and Don’ts and contact details for maintenance and grievance redressal should be available on site.

Providing and fixing ‘THAI CHI SPINNER-4 WHEEL’ manufactured by combination of mild steel and all-season artificial wood to seek eco-friendly greenery effect. Dimensions: (L X W X H) = 1300X1150X1400mm. Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece. Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000. Main center pipe- - 90X90x3mm Thickness Square Tube get maximum internal strength to structure. All round pipes should be of “heavy grade" as per IS 1239 (Highest thickness as per IS 1239). The Thai-chi spinner 4 wheel made from 25NB Heavy grade GI pipe. The ring & bush support pipe made up of 20NB Heavy grade GI pipe. Bearing- 6001 & 6205 is use permanent lubricated reputed brands (SKF/FAG) or self-lubricated imported bushing. Nylon knob with Bearing – Is fixed on shoulder ring pipe for rotating purpose, 4 set to be fixed in a position for kids and adults. Main Pipe Top Closing cap’s- Decent Design Size 120X120 SS304 Material. Hardware Nut & Bolts- Stainless Steel SS Material. Nut & Bolts Closing Caps- All Nut & Bolt Closing caps made from SS304 of 0.7mm thick duly pressed in dies and tools. Foundation stool: Made from main pipe 91x91x2mm pipe and top support of M.S. plate of 250X250mm Square 8mm thickness is welded top. Torque steel is used to support center pipe. Height of stool is 3ft. Foundation plate –M.S. 250X250mm Square With 10mm thick. Foundation stool: Made from main pipe 90x90x3mm pipe and top support of M.S. plate of 250X250mm Square 10mm thickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm. Foundation stool is embedded in C.C. 3:2:1 stock below ground level. Bearing- 6205 use is permanent lubricated reputed brands (SKF/FAG) or self-lubricated imported bushing. Pin’s – Ø 25mm SAE 8620 duly case hardened and centerless grinded. Bearing bushes – Ø 60mm OD seamless pipe. Circlips–A 24 circlips are used for assembly. Safety Instructions and Exercise chart – Made from Aluminum/stainless-steel stick-on product. Powder coating: - The powders to be used of pure polyester material of Reputed make with 70-to-90-micron thickness. Pre-treated with primary coat of 40 microns of etch primer which is specially developed for GI material. Instruction sticker of size 90mm x 160mm of SS 304 rustproof grade plate with 0.8mm thickness duly laser marked printing & riveted on 5mm thick MS plate. Avoided plastic and printed stickers to have lifelong durability. Safety & Maintenance: -All equipment should be tested as per EN16630 safety norms and carries CE mark. Maintenance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user up to 150Kg.

Providing and fixing ‘Peck deck double’ manufactured by combination of mild steel and all-season artificial wood to seek eco-friendly greenery effect. Dimensions: (L X W X H) = 1820X1200X2180mm. Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece. Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000. Main center pipe- - 90X90x3mm Thickness Square Tube get maximum internal strength to structure. All round pipes should be of “heavy grade" as per IS 1239 (Highest thickness as per IS 1239). Remaining frame- made up of 40NB & 50NB Heavy grade G.I. pipe. Handle - Made up of 40NB Heavy grade G.I. pipe. Connecting Link - made up of 25NB Heavy grade G.I. pipe. Seats & Back-rests are of 300x320mm GI antirust material of minimum 2.0 mm thick duly deep drawn in tool & dies with uniform radius of 20mm. Welded permanently with the equipment to avoid future theft, vandalism or damages may occur due to bad handling or misuse. Handle is connected with frame by 8mm laser cutting MS profile. Main Pipe Top Closing cap’s- Decent Design Size 120X120 SS304 Material. Nut & Bolts Closing Caps- All Nut & Bolt Closing caps made from SS304 of 0.7mm thick duly pressed in dies and tools. Foundation stool: Made from main pipe 90x90x3mm pipe and top support of M.S. plate of 250X250mm Square 10mm thickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm. Foundation plate –M.S. 250X250mm Square With 10mm thick. Foundation stool is embedded in C.C. 3:2:1 stock below ground level. Pin’s – Ø25mm & Ø40mm SAE 8620 duly case hardened and centerless grinded. Self-lubricated oilite bushing and ball Bearings are used. Bearing bushes– Ø 60mm & Ø50mm OD made from seamless pipe. Hardware Nut & Bolts- Stainless Steel SS Material. Circlips–A 24 circlips are used for assembly. Safety Instructions and Exercise chart – Made from Aluminum/stainless-steel stick-on product. Powder coating: - The powders to be used of pure polyester material of Reputed make with 70-to-90-micron thickness. Pre-treated with primary coat of 40 microns of etch primer which is specially developed for GI material. Instruction sticker of size 90mm x 160mm of SS 304 rustproof grade plate with 0.8mm thickness duly laser marked printing & riveted on 5mm thick MS plate. Avoided plastic and printed stickers to have lifelong durability. Safety & Maintenance: -All equipment should be tested as per EN16630 safety norms and carries CE mark. Maintenance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user up to 150Kg.

Providing and fixing ‘Bench with Fixed Barbell’ manufactured by combination of mild steel and all- season artificial wood to seek eco-friendly greenery effect. Dimensions (L X W X H)= 1450X950X1500mm. Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece. Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000. Main Frame - Consist – 90X90x3mm Thickness Square Tube get maximum internal strength to structure. All round pipes should be of “heavy grade" as per IS 1239 (Highest thickness as per IS 1239). Backrest frame – Made from 32NB Heavy grade mm G.I. pipe. Backrest Seat should have wooden finish aesthetic look. Fixed weight – Made from 25 od MS bar and 5kg casting round plate is attached at both end of bar. Main Pipe Top Closing cap’s - Decent Design Size 120X120mm SS304 Material. Nut & Bolts Closing Caps - All Nut & Bolt Closing caps made from SS304 of 0.7 mm thick duly pressed in dies and tools. Hardware Nut & Bolts - Stainless Steel. Foundation stool: Made from main pipe 90x90x3mm pipe and top support of M.S. plate of 250X250mm Square 10mm thickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm. Foundation plate – M.S 250X250mm Square with 10mm thick. Foundation stool design suitable to application and is embedded in C.C. 3:2:1 stock below ground level. Powder coating: The powders to be used of pure polyester material of Reputed make with 70 to 90 micron thickness. Pre-treated with primary coat of 40 microns of etch primer which is specially developed for GI material. Instruction sticker of size 90mm x 160mm of SS 304 rustproof grade plate with 0.8mm thickness duly laser marked printing & riveted on 5mm thick MS plate. Avoided plastic and printed stickers to have lifelong durability. Safety & Maintenance: All equipment should be tested as per EN16630 safety norms and carries CE mark. Maintenance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user up to 150Kg. User manual with trouble shooting guide should be available and supply with the equipment. Display for how to use, Do and Don’ts and contact details for maintenance and grievance redressal should be available on site.

Providing and fixing 'Multifunction Trainer' manufactured by combination of mild steel and all-season artificial wood to seek eco-friendly greenery effect. Dimensions: (L X W X H) = 1100X830X2100mm Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece. Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000. All round pipes should be of “heavy grade" as per IS 1239 (Highest thickness as per IS 1239). Main Frame – Consist 90X90x3mm Thickness Square Tube get maximum internal strength to structure. Back support Made by 25NB Heavy grade G.I. Pipe. Leg riser support pipe- 80X40X2.5mm thick rectangle pipe. Attached 5 mm thick MS Plate For Demountable system Handle of 20NB Heavy grade G.I. Pipe.Chin-up support - 40NB Heavy grade G.I. Pipe. Attached 5mm thick MS Plate For Demountable System. Chin-up handle – 25 NB Heavy grade G.I. Pipe. Main Pipe Top Closing Cap - Decent Design Size 120X120mm SS304 Material. Nut & Bolts Closing Caps- All Nut & Bolt Closing caps made from Stainless Steel .Foundation stool: Made from main pipe 90x90x3mm pipe and top support of M.S. plate of 250X250mm Square 8mm thickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm.Foundation plate M.S 250X250mm Square With 10mm thick. Foundation stool design suitable to application and is embedded in C.C. 3:2:1 stock below ground level. Powder coating: - The powders to be used of pure polyester material of Reputed make with 70 to 90 micron thickness. Pre-treated with primary coat of 40 microns of etch primer which is specially developed for GI material. Instruction sticker of size 90mm x 160mm of SS 304 rustproof grade plate with 0.8mm thickness duly laser marked printing & riveted on 5mm thick MS plate. Avoided plastic and printed stickers to have lifelong durability. Safety & Maintenance:-All equipment should be tested as per EN16630 safety norms and carries CE mark. Maintenance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user up to 150Kg.User manual with trouble shooting guide should be available and supply with the equipment. Display for how to use, Do and Don’ts and contact details for maintenance and grievance redressal should be available on site.

Providing and fixing of Outdoor Hand Sanitizer. Dimensions: (L X W X H) = 320X320X1500mm. Main Frame: Structure made from laser cut 3 mm MS sheet. Main Frame Cover: Made from G.I.Sheet of 1.5 mm thickness. Top cap made from G.I. Sheet of 1.5 mm thickness. Bottom plate used of 10 mm thick 320x320 mm square plate of M.S. Material. All MS treated with hot dip zinc to make it anti corrosive. Delivery Chamber: Made from SS 304 sheet metal. Peddle operated mechanism with footrest of 5mm thick M.S. For delivery of sanitizer used NRV of aluminum material. For suction of liquid sanitizer used Diesel pump. Storage Tank: HDPE material with capacity of 5.00 Liter. Refilling: Easy to pour from side and on maximum height should not be more than 3.00 Ft. Nut & Bolts Closing Caps- All Nut & Bolt made from Stainless Steel SS 304 material. Foundation stool: Made from main pipe 90x90x3mm pipe and top support of M.S. plate of 320X320mm Square 10mm thickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm. Foundation stool design suitable to application and is embedded in C.C. 3:2:1 stock below ground level. Overall weight of Sanitizer Stand is around 60.00 Kg. Powder coating: - The powders to be used of pure polyester material of Reputed make with 70 to 90 micron thickness. Pre-treated anti corrosive treatment including Hot Dip Zinc coating. Instruction sticker U.V. Printed on ACP sheet of size 390mm x 180mm x 2.00 mm thickness. User manual with trouble shooting guide should be available and supply with the equipment. Display for how to use, Do and Don’ts and contact details for maintenance and grievance redressal should be available on site.

Supply of sign boards of 0.91 x 0.61m size with support length of 3000 mm. Manufacturing, supplying and fixing of Retro reflective sign boards made of 2 mm thick aluminum sheet face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type – IV of ASTM-D 4956-01 in green and silver white including subject matter, message (bilingual(, symbol and borders etc as per IRC: 67-2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 And fixing the same with suitable sized aluminum alloy rivets @ 20 cm c/c to back support frame of m.s angle iron of size 35x35x5 mm and m.s flat of 25x5 mm along with theft resistant measures, mounted and fixed with 2 nos. clamp of mls flats of size 25x5 mm to a vertical post of 3 mtr height made up of msl pipe of 60 mm n.b welded with two hold fast of m.s angle 25x25x3mm of 30cm length each at bottom and including making holes in pipes, angles, providing & fixing m.s message plate of required size, steel work to be paired with two or more coats of synthetic enamel paint of required shade and of approved brand and manufacture over a priming coat of zinc chromate yellow primer (vertical post to be painted in black/white/grey color) Backside of aluminum sheet to be painted with two or more coats of epoxy paint over an appropriate priming coast including all leads and lifts etc. complete as per drawing, specification and direction of Officer-in Charge

Providing and fixing made of MS sheet 90X60 cm. thick with frame of MS angle 50X50X6mm to diagonal braces at the back of the sheet of MS flat 40X6mm, total height of the board above ground level 2.40m, length of legs below ground 0.30m embedded in CC block 1:2:4 (1cement : 2 coarse sand : 4 graded stone agg. 20mm nominal size) 30X30X15 cm. including excavation and removal of surplus earth within 50m. lead Applying priming coat of approved steel primer, painting with synthetic enamel paint of approved quality and lettering with enamel paint of approved color (one side) as per drawing / direction of Engineer/Work-in-charge.

Providing and fixing of SBR (Styrene Butadene Rubber)Tiles 0f 25 mm thickness using good quality adhesive to paste it on floor.

Greenz

Fair Deal Creation and Marketing

Radhey Mohan International

M/s Khalsa Exports Pvt Ltd