REPAIR/ MAINTENANCE TO OTM BLDGS IN UPPER CAMP UNDER AGE B/R-II AT IMA DEHRADUN

Amount

Dismantling structural steel any description including door steel gates etc complete all as specified and directed.

M&L for Brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 bricks including demolition complete all as specified and directed.

All as per ser item No 2 above but except bricks complete all as specified and directed.

M&L for PCC type C-1 1:3:6 (using 20 mm graded crushed stone aggregate) as in surface channel and drain beads including all necessary form work including demolition complete all as specified and directed.

Extra for forming fair finished drain or channels 30cm inner girth in cement concrete using extra cement including forms, mould, mitied/ stopped ends etc. complete all as specified and directed.

M&L for Rendering 15 mm thick in two layer (10mm + 5 mm) on brick work or concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions including taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etccomplete all as specified and directed. (Water proofing compound to be measured and paid for separately for 5mm thick layer)

M&L for 10 mm thick rendering on fair faces of brick works in cement mortar 1:6 finished even and smooth without using extra cement in cement mortar including taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 05 mm thick rendering on fair faces of concrete such as chajjas/ceiling finished even and smooth without using extra cement in cement mortar 1:3 complete including taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc all as specified and directed. Note : Rate quoted by contractor deemed to be included for plastering chajjas to up to height of 10 mtrs.

Demolation of cement concrete on ground floor and paving n.exc 15cm thick (below or above ground level) complete all as specified.

M&L for PCC 75 mm thick type C-1 1:3:6 (using 20 mm graded crushed stone aggregate) as in plinth protection laid in alternate pannels finished even and smooth without using extra cement complete all as specified and directed.

M&L for 75 thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded crushed stone aggregate) as in sub base for laying floor finishes complete all as specified and directed.

M&L for 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L for 20 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for 10 mm thick rendering on fair faces of brick works in cement mortar 1:4 finished rough for receiving tiles as in dado complete all as specified and directed.

M&L for 7 mm to 8 mm thick non skid coloured ceramic tiles in floor (area of each tile exceeding 0.11 and not exceeding 0.18 sqm) etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

All as per ser item No 16 above but in vertical surfaces including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing)complete all as specified and directed.

M&L for Coloured Vitrified tiles 9 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of existing surfaces including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed. Note : The contractor shall have no claim on difference what so ever on shade/colour of tile.

All as per ser item No 18 above but in vertical surfaces including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for Coloured durastone heavy duty vitrified tiles 9 to 10 mm thick Sq/rectangular tiles area of each tile not exceeding 0.18 Sqm as in floors set and jointed in neat cement slurry and pointed in clooured cement to match the surface including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed. Note : The contractor shall have no claim on difference what so ever on shade /colour of tile.

All as per ser item No 20 above but in vertical surfaces including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing)complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 18-20 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and Mirror polishing including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing)complete all as specified.

M&L for machine cut kota stone slab flooring 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and Mirror polishing including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified.

M&L for 150mm wide strip of makrana white marble 20 mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing types including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified.

M&L for Cement concrete rich colored chequered tiles machine pressed with imported pigment smooth finish of size (300 mm x 300 mm or any size as approved 20 to 25 mm) thick set and jointed with neat cement slurry including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for 15 mm to 18 mm thick granite stone slab as in shelves/vertical surfaces/platforms set and jointed in neat cement slurry, pointed in colored cement to match the shade including rubbing of moulding and mirror polishing etc including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed. (Shade and colour as approved by GE)

M&L for Grinding and Mirror polishing on existing marble / granite/ kota stone /mozaic/ stone work where ever required to give high glass finish complete

M&L for Coloured glazed ceramic tiles size (300 mm x 600 mm x 7 mm/300 mm x 450 mm x 7 mm or 8 mm thick) set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments in vertical surfaces including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing)complete all as specified and directed. Note : Contractor shall have no claim on colour or shade what so ever on this account.

M&L for Sand cushioning under floors including watering and consolidation complete all as specified and directed.

M&L for Coloured machine pressed/vibro mechanically floated interlocking paver block any shape and size confirming to IS - 15658-2006 of 60 mm thickness, M-35 grade, with topping of cement mixed with imported pigment colour and shape shall be approved and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed by Engr-in-Charge.

M&L for Machine pressed (factory made) plain cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate), kerb stone of any size, laid in trenches on edges of roads joints fitted in CM 1:4 including excavation in any type of soil, PCC bed, returning filling and removal of surplus soil to a distance not exceeding 50 m from the starting point complete all as specified and directed.

M&L for Rolled section/tubular section as in main and cross beams, purlins, rafters, posts where connected to common rafter and running rails etc confirming to Fe-410-W complete all as specified and directed of approved make.

M&L for Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work,incl locking arrangement for water tanks and similar work conforming to Fe 290 Gd E-165 complete all as specified.

S&F Hard Drawn steel wire fabric cut to length bent to shape required and tying,welding to the angle iron frame etc complete all as specified and directed.

S&F 4 mm thick E-board false ceiling (Classic) including galvanised colour coated snap grid frame for false ceiling, size of grid 605 X 605 mm fixed with 1.6 mm dia GI wire suspenders one end tied to roof members and other end connected to main tee of grid framework by means of 4mm dia adjustable "J" hook consisting of two Nos washers and two nuts at 1.2 mtr centres all as specified and as directed by Engineer-in charge (size of main tee 38 mmX25 mmX 1.4 mm, cross tee 38 mm X 25 mm X 1.4 mm angle along walls 38 mm X 25 mm X 2.0 mm soft cleats 25 mm X 37 mm, thickness 1.8mm, Renell plug 12.7 mm dia all as specified in SSR and two coats of oil bound emulsion complete all as specified and directed including dismantling boarding any description fixed in any position with nails.

S&F pre-painted galvalume aluminium zinc coating GI based Plain steeel sheet 0.50mm thick an colour having tensile strength of 550 Mpa as in roof covering/ridge/cladding to wall fixed with self tapping screws all as specified ncluding dismantling asbestos corrugated or semi corrugated sheets as in roof covering including ridge etc

S&F pre-painted galvalume aluminium zinc coating GI based tile profile corrugated steeel sheet 0.50mm thick any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified ncluding dismantling asbestos corrugated or semi corrugated sheets as in roof covering including ridge etc all as specified

M&L for Roughing surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @3kg/Sqm mixed with water proofing compound including 20mm thick screeding in CM (1:4) finished even and smooth mixed with water proofing compound complete all as specified and directed. (WPC shall be measured and paid separatley) Note : No extra cost shall be paid to contractor in r/o any removal of existing roof treatment.

M&L for Priming surfaces with bituminous primer confirming to IS-3384 @ 0.40kg/sqm, after drying of primer applying a coat of hot blown bitumen confirming to IS-702 @ 1.20 kg/sqm and layin polymeric water proofing membrane, five layerd with centre core of 90 micron high molecular density polythelene film (minimum weight 3.5 kg per sqm) with end over laps not less than 150 mm and side lap 75 mm complete all as specified and directed for sunken floor treatment or painting with solar reflective paint for roof surfaces.

M&L for Providing cement concrete in steps, seismic and other similar bands, pad paraping concrete and railings up to 60 cm in height, coping, apex stones, bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 complete all as specified and directed.

Supply only (LW+) water proofing liquid solution of Dr fixit/sikka or equivalent make complete all as specified and directed.

MS drapery 25mm dia rod powdered coated including brackets and necessary fitting "as in repair" complete all as specified and directed by Engr-in-Charge.

S&F110 mm bore PVC (SWR) pipe pressure rating 6 Kg/Cm2 single socketed, in any length with rubber joints fixed to walls including demolition of and breaking up of AC rain water pipes any dia fixed in any positioncomplete all as specified and directed.

S&F 110 mm bore PVC (SWR) bend any radius including demolition of and breaking up of AC rain water pipes any dia fixed in any position complete all as specified and directed.

S&F 15 mm bore medium grade galvanished iron water tubing with all fittings and fixed complete to walls or laid in trenches including taking up or down steel tubing complete all as specified and directed.

S&F 20 mm bore medium grade galvanished iron water tubing with all fittings and fixed complete to walls or laid in trenches including taking up or down steel tubing complete all as specified and directed.

S&F 500 ltrs capacity rotational moulded polythene water storage tanks cylndrical with closed top hoisted three layered ISI marked and fixed in position including dismantling water tank complete all as specified and directed.

All as per ser item No 47 above but 1000 ltrs capacity including dismantling water tank complete all as specified and directed.

All as per ser item No 47 above but 2000 ltrs capacity including dismantling water tank complete all as specified and directed.

S&F 20 mm bore brass float valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule "as in repair" complete all as specified and directed.

Supply and fixing PVC tank lid for 1000 to 2000 litre capacity including all locking arrangements, nuts, bolts etc for fixing complete all as specified and directed by Engr-in-Charge

Cleaning of PVC water tank exc 500 ltrs and not exc 1000 ltrs and removing all scale and dirt, from tanks and from mouths of circulating pipes, upto EIC satisfaction.

Cleaning of pvc water tank exc 1000 ltrs and not exc 2000 ltrs and removing all scale and dirt, etc from tanks and from mouths of circulating pipes, upto EIC satisfaction.

S&F in repair single piece Vitreous china any shade cascade floor mounted single piece water closet P/S trap with dual flush cistern for UF soft close slim seat cover, hinges fitting, conversion bend, fixing accessories set complete all as specified and directed. Make : Jaquar Cat part No OPS-WHT15753NS250UFSMZ/ Cera cat part No S1013105/Kajaria cat part No KB-3007

S&F Vitreous china full set pedestal type wash basin, white, flat back, size 585x450x220mm including bracket, CP brass waste coupling and waste pipe fixed in repair complete all as directed. Make : Jaquar Cat part No Jaguar FLS-WHT-5801 & 5301/Cera cat part No S2040112 & S2090107 or equivalent in Kajaria/Somany

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long.

S&F in repair Corner glass shelf assembly with bracket complete all as specified and as approved.

S&F in repair toilet paper holder with flap guard fixed to walls with chromium plated brass screws. Make : as approved.

S&F in repair soap dish holder fixed to walls with chromium plated brass screws.

S&F in repair soap dispenser fixed to walls with chromium plated brass screws.

S&F CP brass hot & cold single lever basin mixer with 450mm long braided hoses cast copper alloy with centre hole for WHB complete all as directed by Engineer-in-charge. Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series

S&F CP brass hot & cold 15mm dia wall mixture for mixing hot & cold water with shower provn with connecting legs & flanges in complete all as specified. Make : Jaquar Opal Prime Series/Cera Ruby series/Somany Bellis series

S&F in repairs CP brass hot & cold 15mm dia single lever sink mixer swinging spout (wall mounted model) with connecting legs & wall flanges complete all as specified. Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series

S&F in repairs Sink made of stainless steel 1 mm thick kitchen or laboratory with plugs, coupling, washers and waste pipe including bedding in cement morter on to dwarf wall or including fixing cantilver brackets overall size 405mm x 460mm x 203 mm bowl size 405 mm x354mm x 203mm complete all as directed.

S&F 15mm bore long body bib tap chromium plated fancy type with wall flange and aerator fixed in repair complete all as specified and directed. Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series

S&F CP fancy type Angle valve 15mm dia (angle cock) cast copper alloy with wall flange. Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series

S&F CP fancy type twin Angle valve 15mm dia (angle cock) cast copper alloy with wall flange. Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series

S&F in repair CP Health faucet telephonic type with CP with 1.5m long flexible pipe. Make : Jaguar/CERA/Somany

S&F in repair CP brass overhead shower square fancy type 100x100 mm with extension CP Arm pipes. Make : Cera/Jaquar/Somany

S&F in repair brass chromium plated towel ring fixed with screw in wall complete all as specified and directed. Make : Cera/Jaquar/Somany

S&F in repair brass chromium plated towel rail, 600mm long. Make : Cera/Jaquar/Somany

S&F in repair brass chromium plated towel rack with hooks, 60cm long between flanges complete all as specified and directed. Make : Cera/Jaquar/Somany.

S&F of tooth brush/paste tumbler holder fixed to walls with chromium plated brass screws. Make : Cera /Jaquar/Somany

S&F Viterous China urinal half stall type white including CP water spreader, waste pipe etc. "as in repair" complete all as specified and directed.

S&F PVC flushing cistern 10 ltrs capacity ISI marked as approved with complete in let ball valve as in repair complete all as specified and directed.

S&F Vitreous China squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including cast iron P trap, bore of pipe 100 mm and provision of concrete bedding "as in repair" complete all as specified and directed.

S&F Viterous china wash hand basin flat back size 580 x 450 mm excluding traps, waste, chain, plug and porcelain stopper including brackets "as in repair" complete all as specified and directed.

S&F in repair PVC connection 15mm bore with PTMT nuts of length 450mm

M&L for Two coats of oil bound distamper on new surfaces over and including a coat of primer on internal walls complete all as specified and directed.

M&L for Two coats cement base paint on newly plastered surfaces including preparation of surfaces on external walls complete all as specified and directed.

M&L for Three coats of white wash on newly plastered ceiling surfaces including preparation of surfaces complete all as specified and directed.

M&L for Two coats of synthetic enamel paint on new steel surfaces including preparation of surfaces over and including a coat of red oxide zinc chrome primer complete all as specified and directed.

Two coats of synthetic enamel paint on new wooden surfaces including preparation over of surfaces over and including a coat of pink primer complete all as specified and directed.

Material & Labour for applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over old surfaces all as per manufacturers instruction and directed by EIC

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces all as per manufacturers instruction and directed by EIC

Taking down chowkats or frame with shutter (without taking of shutter off shutters from frame) 1.5 sqm and not exceeding 4 sqm each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and directed by Engineer-in-Charge.

All as per ser item No 87 above but not exceeding 1.5 sqm complete all as specified and directed.

Taking down shutters of any description exceeding 1 square metre not exceeding 2 square metre each complete all as specified and directed.

All as per ser item No 89 above but not exceeding 1 sqm each complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite ) soild door/ window Ceostory windows & other frame / chowkhat single/double patam of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Supension Grade) , calcium carbonate and natural fibers (wood powder / rice husk / wheaat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) fabbricated with miter joints after applying PVC solvent cement and screws with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withrawal strength of 2200 N cum , (Face) & 1100 N (Edge) , minimum compressive srength of 58 N/mm², modules of elasticty 900 N/ mm² and resitance to spread of flame of class A category with property of being termite / borer proof , water / moisture proof and fire retardant. and fixied in position with MS hold fast/ lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-In-Charge.(M.S. hold fast/ lugs or SS dash fasteners shall be paid fo separately ) . Note : For WPC solid door/ window frames , minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable . Variation in profile dimension on plus side shall be accepetable but no extra payment on this account shall be made.

S&F Providing and fixing factory made single extruded WPC (wood polymer Composite ) soild decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (suspension Grade ), calcium carbonate and natural fiber (wood powder/ rice husk / wheat husk) and non toxic additives ( maximaum toxicity index of 12 for 100 gms ) having minimum density of 650 kg/cum and screw whithrawal strenght of 1800 N (Face ) & 900 N (Edge ) , minimum compressive strength 50 N/mm² , modulus of elasticity 850 N/mm² and resistance to spread of falme of Class A category with property of being termite /borer proof , water/moisture proof and fire retardant . WPC to be laminated with PVC foil of minimum 14 microns thic of approved desing pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel but hinges of required size with necessary full body threaded star headed counter sunk S.S screws., all as per direction of Engneer-In -Charge . ( Note : Stainless steel but hinges and necessary S.S srews shall be paid seprately )

M&L for 35 mm thick plain framed second class hard wood panelled factory made shutters (two panel or more panel) with lock rail and panel of 12 mm thick BWP commercial ply with size of rail and stiles as per IS 1003 (part-1) kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for 35 mm thick plain factory made second class hard wood skeleton shutters, four paneled, open rebated and prepared to receive glass, guage etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitered bead for securing glass etc with size of member of shutters complete all as specified and directed in clause 8.24 (a) of SSR Part-I kiln seasoned and chemically pressure treated.

S & F Ist Class hard teak wood, Plain and semi circular at top chowkats & frame wrought rounded or chamfered put together with glue pinned atg joints and fixed including dismantling complete all as specified and directed

S&F Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1302/2009 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Description all as per ser item No 97 as above here in before but without glazing bar complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately

S&F aluminium powder coated door fixed on aluminium frame of section 47.62mm x 44.45x1.6 mm thick, shutter glazed with tinted glass (Modi Guard) 5mm thick fixed with rubber gasket and aluminium strips as per standard method also rubber gasket at frame so as to make air tight with cast type handle aluminium anodised of 150mm size 2 Nos (One on each side of shutter) with shutter bottom rail 150mm x 44.45mm x1.6mm thick section, middle and top rail 83.5mm x 44.45mm x 1.6 mm thick section, side style 83.5mm x 44.45mm x 1.6 mm thick section all as sper IS 737- 1986 fixed with aluminium (extruded section) hydraulic door closer egulated designation No-3 universal type and make with aluminium tower bolt arrangement of standard make with locking arrangement with 6 levers mortise lock(brass body) of size 100mm etc complete all as specified and as directed.

S&F 18-19 mm thick prelaminated colour WPC sheet for cabinet shutter and frame &fixed at site colour as approved by Engr-in- Charge complete all as spd.

S&F auto closing hinges 35mm of 0 crank(KH001) OR 8 CRANK (kh-002) openable at 110 degree for cabinet shutter fixed in repair complete all as spd.

S&F Stainless steel handle 125mm size for cabinet shutter fixed in repair complete all as spd

S&F in repairs PVC sandwich wall Lining consisting of 5mm thick wood grains printed PVC sheet complete fixing at site as specified and directed.

M&L for 03mm thick sheet glass, ordinary quality and glazing with wooden beading not exceeding 0.5 Sqm in each pane including hacking out old broken glass complete all as specified and directed.

M&L for 03mm thick figured glass, pin head type and glazing with wooden beading, not exceeding 0.5 Sqm in each pane including hacking out old broken glass complete all as specified and directed.

M&L for french polishing on wooden surface of any discription width or girth including cleaning and preparing the surface including a coat of wood filler but one or more coat on new work complete all as specified and directed.

M&L for french polishing on wooden surface of any discription width or girth including cleaning and preparing the surface including a coat of wood filler but one or more coat on old work incl complete removal of exiting paint complete all as specified and directed.

M&L for preparation of old polished wooden surfaces of any description over 10cm width or girth and applying one coat of manson polish complete all as specified.

M&L for preparation of old painted plastered surfaces of walls, pillars and applying one coat of synthetic enamel paint complete all as spd.

S&F floor door stopper 140mm of brass body and tougue with hard steel spring complete all as spd and as approved.

S&F In Repair floor door stopper 140mm of brass body and tongue with hard steel nspring complete all as spd.

S&F Ist class teak wood moulding as Exc 3 & n exc 6 sq.cm in cornices picture rails and the like complete all as specified and directed.

S & F Fancy and decorative type 300mm long brass barrel tower bolts with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

S & F Fancy and decorative type 300mm long brass barrel tower bolts with cast or sheet barrel and rolled or cast bolts and fixed in repair complete all as specified and directed.

S & F Fancy and decorative type 150mm long brass barrel, semi barrel and skeleton tower flush bolts type 2 and fixed in repair flush complete all as specified and directed.

S & F Fancy and decorative type 150mm long brass barrel, semi barrel and skeleton tower flush bolts type 2 and fixed flush complete all as specified and directed.

S & F 150 mm butt hinges, cast brass with mild steel hing pin bright polished and fixed type B-11 complete all as specified and directed.

S&F 75 mm butt hinges, cast brass with mild steel hing pin bright polished and fixed type B-11 complete all as specified and directed.

S & F Fancy and decorative type 300mm long brass sliding door bolt with sand or die cast brass hasp staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed in repair complete all as specified and directed.

S & F Fancy and decorative type 300mm long brass sliding door bolt with sand or die cast brass hasp staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed.

S&F Stainless steel Grating for Nahani trap 100mm dia

S & F Fancy type and decorative 150mm log extruded brass handles fabricated type polished fixed in repair complete all as specified and directed.

S & F Fancy type and decorative 150mm log extruded brass handles fabricated type polished complete all as specified and directed.

S&F Aluminium body heavy duty double action floor spring suitable for glass shutter at both side rotable complete all as specified and directed.

S&F Aluminium door closer hydraulically regulated universal type, suitable for door shutters complete all as specified and directed.

M&L for repair by dismantlig of existing wooden floor and provide new HDF laminate wooden flooring of 15 mm thick over 2 mm thick Foam sheet over a layer of polythene film sheet over and including wooden fillets of size exc 16 sqcm but not exc. 25 sqcm and all necessary fixtures to match with existing floor level and finished top finished floor. completed all specified and directed.

M/S PUNDIR BUILDERS (BID ID -3331385)

M/s Vinod Singh Negi (BID ID -3330246)

Pragati Enterprises (BID ID -3340077)