Annual Plan 144 25 Maintenance to the Assistant Executive Engineer office Kanjikuzhi BP Annual Plan

Amount

AEE office

OD149891/2024-2025:Providing and fixing Table top partition - 1800L x 600D x 750ht,Side Storage -1200L x 450D x 725ht,Partition - (2700+1800)L x 1500ht size with Table top - 25mm thick pre laminated particle board finished with 2mm edge lipping finish.Understructure - 18mm thick gable end and modesty panel is considered.System Partition - 75mm insert type system with 1200Ht, finished with Fabric above &laminate tile below table top with one Soft Board Tile & Marker Tile. Storage - Storage top is made of 25mm thick particle board with edge banding finish and rest all made of 18mm thick particle board with 3 drawers, swing door and lock. etc. complete as per architectural drawing and direction of Engineer-in-Charge.

OD148176/2024-2025:Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of thebuilding , for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Alumini um sheets each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.(from 25.7) Details of cost for 6.72 sqm. Width of the unit 1.6 m , Height of the unit 4.2 m Area of Single Unit 6.72 m2 Total Area 6.72 m2 No of Panels 1 no Area i/c wastage @ 5% 7.06 m2

OD149877/2024-2025:Supplying and fitting Acrylic letters of size 15 cm height fixed on 2 mm imported sheet 2.5 cm side projection 4mm foam sheet back tray as per the direction of the Departmental Engineers at the site.

18.48:Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

SATHEESH KUMAR M

Bidder Name

SREEKUMAR

SATHEESH KUMAR M