PETTY REPAIR/DAY TO DAY MAINT WORK INCLUDING REPAIR/REPLACEMENT TO JOINERY, PLUMBING, SANITARY, ROOF, PLASTERING AND OTHER ALLIED CONNECTED BLDG REPAIR WORKS IN MD-II AND OTHER AREAS ACCN OF AGE B/R-II OF GE (NORTH) AMB

Amount

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the Engr-in-charge.

M&L brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M & L taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge

M&L rendering 15 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:4 and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L rendering 15 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:6 and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L rendering 10 mm thick on fair faces of brick work or concrete ceiling or chajjas surfaces in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg. which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge.

M & L preparing new plastered/unplastered surfaces and applying two coats of cement base paint on surfaces of walls, chajjas, roof projection complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of newly plastered/ unplastered surfaces of walls and applying two coats of oil bound distemper with painting roller over a coat of primer over and including 1-2 mm thick wall care putty in two or more coats to achive smooth surface over prepared surfaces complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of newly plastered/unplastered surfaces of brick/concrete ceiling and applying two coats of white lime wash complete all as specified and as directed by the Engineer-in-Charge.

Taking down loose plaster from ceiling of slab, edges and soffit of chajjas and the like, cleaning surface with wire brush to remove all dust/dirt/loose particles to expose old steel reinforcement, applying neat cement slurry@ 3Kg per sqm and 30mm thick (in two layers , each layer 15mm thick) plaster in cement mortar 1:3 not exceeding 5 sqm each patch including removal of rubbish/demolished material to a distance exceeding 250mtr and not exceeding 500mtr , including scaffolding up to 3m height and applying two coats of cement base paint complete all as specified and as directed by Engineer-in charge .

Taking down loose plaster from ceiling of slab, edges and soffit of chajjas and the like, cleaning surface with wire brush to remove all dust/dirt/loose particles to expose old steel reinforcement, applying neat cement slurry@ 3Kg per sqm and 30mm thick (in two layers , each layer 15mm thick) plaster in cement mortar 1:3 not exceeding 5 sqm each patch including removal of rubbish/demolished material to a distance exceeding 250mtr and not exc 500mtr , including scaffolding 3m to 7m height and applying two coats of cement base paint complete all as specified and as directed by Engineer-in charge .

Taking down loose plaster from ceiling of slab, edges and soffit of chajjas and the like, cleaning surface with wire brush to remove all dust/dirt/loose particles to expose old steel reinforcement, applying neat cement slurry@ 3Kg per sqm and 30mm thick (in two layers , each layer 15mm thick) plaster in cement mortar 1:3 not exceeding 3 sqm each patch including removal of rubbish/demolished material to a distance exceeding 250mtr and not exc 500mtr , including scaffolding at any height and applying three coats of white lime wash complete all as specified and as directed by Engineer-in charge .

S & F in repair mild steel powder coated wooden finish curtain rod 25mm dia having wall thickness 1:6 mm fixed with and including decorative brackets ,stop roller and glass at the end etc complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

M & L galvanised iron tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

M & L galvanised iron tubing 20 mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

S&F bib taps 15mm bore fancy type brass chromium plated with long body screwed down, screwed for iron pipe or for brass ferrule and fixed as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F fancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

M & L 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement as in repair complete all as specified and as directed by the Engineer-in-Charge

S & F 15mm bore cast copper alloy fancy type chromium plated stop valves, screwed down, high pressure with butterfly handle, scrwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges as in repair complete all as specified and as directed by the Engineer-in-Charge

S & F 15mm bore cast copper alloy angular type chromium plated stop valves, screwed down, high pressure with butterfly handle, scrwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F vitreous china wash hand basin white, flat back of size 550mmx400mm with pedestal fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F vitreous china squatting pan, Orissa pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F 10 ltr PVC valveless syphonic action type flushing cistern with brackets, flush pipe etc complete including inlet ball valve float and handle including brackets, of approved make including all connections & flush pipes for WC as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern) including plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device and brass chromium plated Jet spray with PVC pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F sinks without drainage board made out of stainless steel 1mm thick sheet for kitchen or laboratory with plugs, waste pipe, brass chromium plated coupling and wastes; in-cluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connect-ing union to pipe overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm as in repair complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing plastic water closet seat cover , white closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminised hinging device, as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F 32 mm dia PVC waste pipe for wash hand basin / Kitchen sink etc of standard length as in repair complete all as specified and as directed by the Engineer-in-Charge.

Dismantling water tanks of capacity exc. 250 ltr and not exc. 500 ltrs and removing from site complete all as specified and as directed by the Engineer-in-Charge.

S & F 500 litres rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) 100% UA stablised, rust proof, hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed by the Engineer-in-Charge. Note:- Tank shall be in white colour.

S & F 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe and fixed (minium weight 210 gm )complete all as specified and as directed by the Engineer-in-Charge.

S & F 15 mm bore Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but not exc 4 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-charge.

Taking down shutters of any description area exc 1 sqm and not exc 2 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge

M&L factory made 2nd class hard wood 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on boths face . The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and as directed by the Engineer-in-Charge.

M&L factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters,open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be seasoned and chemically pressure treated) complete all as specified and as directed by the Engineer-in-Charge.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet single side and balance 5mm plain colour PVC sheet reinforced with MS square tube fixed in opening including edges will be painted to match with prelam sheet complete all as specified and as directed by the Engineer-in-Charge.

S&F factory made solid PVC moulded door shutters with partical board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick prelaminated moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing complete all as specified and as directed by the Engineer-in-Charge.

M&L rolled mild steel framed work as in chowkhats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-410-W(Gde E-250) quality 'A' complete all as specified and as directed by the Engineer-in-Charge.

M & L PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in holdfasts complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs, guard bars and painting etc. all as shown on drawing No. TD-219 sheet 1/3 to 3/3 and TD-220 sheet 1/3 to 3/3 as applicable complete all as specified and as directed by Engineer in Charge. Note: (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill fabricated from 10mm square MS bar as shown on drgs. (iii) Glazing, wire mesh shall be measured and paid for separately.

S&F 150 mm long aluminium handle cast type anodised complete all as specified and as directed by the Engineer-in-Charge.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 250mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter complete all as specified and as directed by the Engineer-in-Charge.

S & F butt hinges 100mm long of stainless steel medium weight complete all as specified and as directed by the Engineer-in-Charge.

S&F mild steel 300 mm ordinary rat tail rod pattern springs including roller and roller plate etc complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair stainless steel butt hinges 100mm long medium weight complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair butt hinges 75mm long of stainless steel medium weight complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair 100 mm long aluminium handle cast type anodised complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair 300mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair grating doom 100mm dia of stainless steel complete all as specified and as directed by the Engineer-in-Charge.

S & F 40 mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair 32mm dia brass chromium plated waste coupling for wash hand basins complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair 38mm dia brass chromium plated waste coupling for kitchen sink complete all as specified and as directed by the Engineer-in-Charge.

Resecuring or easing & adjusting shutters of any description not exc 1 Sqm each, without taking down shutters complete all as specified and as directed by the Engineer-in-Charge

Resecuring or easing & adjusting shutters of any description exc 1 sqm and not exc 2 Sqm each, without taking down shutters complete all as specified and as directed by the Engineer-in-Charge

Taking down of steel door shutters (sliding or side hung) exceeding 1:00 Sqm and not exceeding 2:00 Sqm each and repairing the same for its proper functioning with greasing/oiling/ /straightening and necessary cutting and welding of door parts and making the door functional for easy movement with and including reerecting the door shutter in existing position all as directed by Engineer-in-charge.

M&L for running welding in repairs thickness to metal to be welded not exc 6mm complete all as specified and directed by Engr-in-charge.

M&L preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds and steel window frame glazed with putty or fixed with beads complete all as specified and as directed by the Engineer-in-Charge.

Taking down eaves gutters, rainwater pipes and plumbing/ sewer pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified & directed by the Engr-in-Charge.

M & L sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer-in-Charge

S&F galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tack or galvanised wire staple complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repar galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tack or galvanised wire staple complete all as specified and as directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

M&L Non-skid ceramic coloured tiles joint free 1st quality (square/rectangular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L glazed ceramic coloured tiles joint free 1st quality in vertical surfaces/skirtings/dados of size 350x250x7mm/450x350x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M & L 25mm thick cement concrete 1:2:4 type B-1, using 20mm graded crushed stone aggregates as in sub base of floor and finished even and fair to receive tiles etc. complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exe 15 cm thickness (below or above ground level) complete all as specified and as directed by the Engineer-in-Charge.

M & L 40mm thick plain cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in floor, laid in panels and surface finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M & L 75mm thick cement concrete 1:4:8 type D-2, using 40mm graded crushed stone aggregates as in sub base of floor and finished even and fair complete all as specified and as directed by the Engineer-in-Charge.

S&F glass dividing strips, 38mm wide and 3mm thick, insrted in position to confirm to design complete all as specified and as directed by the Engr-in-charge.

M & L prepolished granite slab 18(+2)mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone laid over & including 15mm thick screed bed in CM 1:4 as in pillars, steps etc complete including moulding of edges and polishing complete all as specified and as directed by the Engineer-in-Charge.

Dismantling boarding of any discription, fixed in cup boards/ward robes or fixed in any position in hardware etc complete all as specified & directed by the Engr-in-Charge.

S&F 18mm thick LEAD FREE PVC celuka ply of both side plain of approved color other than white colour fixed with screws solvent cement / adhesive to make kitchen / bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer's specifications complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by the Engr-in-charge.

M & L PCC 1:5:10 Type E-2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete for sunken portion complete all as specified and as directed by the Engineer-in-Charge.

Material and labour 15mm thick cement plaster in cement mortar 1:4 mixed with water proofing compound @ 2% by weight of cement or as per manufacurer's instruction, finished even and fair and applying one coat of hot bitumen of grade 85/25 @ 1.20 Kg/Sqm over and including bitumen primer coat @ 0.30 ltrs/ Sqm as in sunken floor etc complete all as specified and as directed by the Engineer-in-Charge (cost of WPC shall be deemed to be included in quoated rate of this item).

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls complete all as specified and as directed by the Engineer-in-Charge

S&F PVC(SWR) bends of any radius, for 110mm bore pipes complete all as specified and as directed by the Engineer-in-Charge.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls complete all as specified and as directed by the Engineer-in-Charge.

S & F 75mm bore PVC (SWR) bends of any radius complete all as specified and as directed by the Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation etc or for shafts, wells, manholes etc. not exc 10 sqm on plan and not exc 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed by the Engineer-in-Charge.

M & L concrete bed in PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate to drain pipes including packing under and haunching against the sides of pipes, after they are laid and tested for 110 mm dia (internal) pipes complete all as specified and as directed by the Engineer-in-Charge. (Pipes shall be measured & paid separately).

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge

Returning, filling in, including spreading, lavelling ,watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed by the Engineer-in-Charge.

Removing surplus excavated material to a distance exc 250m but not exc 500m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

M & L for providing precast PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, precast cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in CM 1:4 complete with joints to match, except blocks or slabs incluidng form work complete all as specified and as directed by the Engineer-in-Charge.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, chajjas, staircases, landings and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and as directed by the Engr-in-charge.

M & L RCC 1:2:4 type B1 using 20mm graded crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by the Engineer-in-Charge.

M&L TMT mild steel bars 10mm dia and over cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), work in rough finished flat surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge

M & L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide, for rough finished surface of concrete complete all as specified and as directed by the Engineer-in-Charge

M&L for Cleaning and removing all scale and dirt,etc from PVC/RCC tanks and mouths of circulating pipe of exc 250litre and not exceeding 1000 litre capacity & writing on the tank with synthetic enamel paint not less than 70mm long and 2mm wide of words in shape like cleaned on : 15.06.2018 complete all as specified and as directed by the Engineer-in-Charge. NOTE :- Unit rate shall be included to make small fittings such as elbow, socket, reducer, tee, union etc .

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white lime wash over prepared surfaces of wall, pillar, cornices complete all as specified and as directed by the Engr-in-charge.

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of white lime wash over prepared surfaces of the walls pillars, cornices etc. complete all as specified and as directed by the Engr-in-charge.

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white lime wash on ceiling complete all as specified and as directed by the Engr-in-charge.

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of white lime wash on ceiling complete all as specified and as directed by the Engr-in-charge.

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper with painting roller over prepared surfaces of the walls, pillars, cornices etc. complete all as specified and as directed by the Engr-in-charge.

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of oil bound distemper with painting roller over prepared surfaces of walls pillars, cornices etc. complete all as specified and as directed by the Engr-in-charge.

M & L complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, washing down with water to remove loose particles etc complete all as specified and as directed by the Engineer-in-Charge

M&L applying one mm thick wall care putty in two or more coats to achive smooth surface over prepared surfaces complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of old decorated brick/concrete, plastered / un plastered surfaces of walls, pillars cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and finishing walls with Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm) complete all as specified and as directed by the Engr-in-charge.

M&L preparation of old decorated brick/concrete, plastered / un plastered surfaces of walls, pillars cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of cement base paint on the walls, pillars, cornices etc. complete all as specified and as directed by the Engr-in-charge.

M&L preparation of old decorated brick/concrete, plastered / un plastered surfaces of walls, pillars cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of cement base paint on the walls, pillars, cornices etc. complete all as specified and as directed by the Engr-in-charge.

M&L preparation of old decorated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel (ordinary tint) complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of old decorated steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel (ordinary tint) complete all as specified and as directed by the Engineer-in-Charge.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed by the Engineer-in-Charge.

Dismantiling timber framed work scantling 40sqm cm and over in section in any position complete all as specified & directed by the Engr-in-Charge.

S & F 6mm thick asbestos cement, corrugated or semi-corrugated sheets fixed with L-type or J-type or cranked hook bolts in roofs, walls etc. complete all as specified and as directed by the Engineer-in-Charge

S & F 6mm thick asbestos cement two piece adjustable plain wing ridge and fixed with L-type or J-type or cranked hook bolts in roofs, walls etc. complete all as specified and as directed by the Engineer-in-Charge

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick having zinc coating 150 gm per sqm (Az 150) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

S & F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa having zinc coating 150gm per sqm (Az 150) coating as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

S & F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St-240 complete all as specified and as directed by the Engineer-in-Charge.

Checking of joinery (wooden/steel) iron/aluminium mongery, pelmet box, door springs etc requiring carpentry work and carrying out minor repairs such as tightening of screws/nails, fixing glass panes, minor adjustment of joinery, door etc. including petty repairs material like screws/nails, plug etc. to make it functional complete all as specified and directed by Engineer-In-Charge. Note : Any items required to be replaced shall be paid under respective items.

Checking of floor, plinth, plaster etc requiring masonry work and carrying out minor repairs such as edges, patches etc, including petty repairs material like sand, cement & aggregate to make it functional complete all as specified and directed by Engineer-In-Charge. Note : Any items required to be replaced or major repair shall be paid under respective items.

Checking and attending to water leakage from taps, flushing cisterns, wash hand basins and other sanitary fittings/fixtures and any obstruction to water supply, requiring plumber work and carryout minor repairs such as replacement of washers, check nuts, tightening of fittings of flushing cistern etc including petty materials like washers of all sizes, thread(shoot), M-seal, screws, nails to make water supply/ plumbing lines functional and leak proof complete all as specified and directed by Engineer-In-Charge. Note : Any items required to be replaced shall be paid under respective items.

M&L cleaning of sewage line up to first man holes including blockage of WC, EWC, bathroom/WHB/kitchen floor trap and also and including cleaning of sludge from Ist main hole by mechanical or any other mean, removal of sludge exc 50m but not exc 100m complete all as specified and as directed by the Engineer-in-Charge.

M/s Vridhi Construction Co.

Durga Enterprises

shiv const co

MAYANK ENTERPRISES

Saurav Enterprises