PROVN OF OTM ACCN FOR DIV ENGR REGT(PH-1) AT KOTA MIL STN

Amount

Lump Sum price worked out by the bidder for "Building Works" as listed in Schedule `A' Part-I **Above/below the lump sum price inserted by the MES in Schedule `A' Part-I.

Lump Sum price worked out by the bidder for "Internal Water Supply" as listed in Schedule `A' Part-II **Above/below the lump Sum price inserted by the MES in Schedule `A' Part-II.

Lump Sum price worked out by the bidder for "Internal Electrification" as listed in Schedule ‘A’ Part-III **Above/below the lump Sum price inserted by the MES in Schedule ‘A’ Part-III.

Lump Sum price worked out by the bidder for "External Water Supply" as listed in Schedule `A' Part-IV **Above/below the lump Sum price inserted by the MES in Schedule `A' Part-IV.

Lump Sum price worked out by the bidder for "External Electrification" as listed in Schedule `A' Part-V **Above/below the lump Sum price inserted by the MES in Schedule `A' Part-V.

Lump sum price worked out by the bidder for "Road, Path and Culvert " as listed in Schedule ‘A’ Part-VI **Above/below the lump Sum price inserted by the MES in Schedule ‘A’ Part-VI.

Lump Sum price worked out by the bidder for "Sewage Disposal" as listed in Schedule `A' Part-VII **Above/below the lump Sum price inserted by the MES in Schedule `A' Part-VII.

Lump Sum price worked out by the bidder for "Area Drainage" as listed in Schedule `A' Part-VIII **Above/below the lump Sum price inserted by the MES in Schedule `A' Part-VIII.

Lump Sum price worked out by the bidder for "Security Fencing, Wall & Gate" as listed in Schedule `A' Part-IX **Above/below the lump Sum price inserted by the MES in Schedule `A' Part-IX.

Lump Sum price worked out by the bidder for "Site Clearance and Earthwork" as listed in Schedule `A' Part-X **Above/below the lump Sum price inserted by the MES in Schedule `A' Part-X.

Lump Sum price worked out by the bidder for "Water Cooler" as listed in Schedule `A' Part-XI *Above/below the lump sum price inserted by the MES in Schedule `A' Part-XI.

Lump Sum price worked out by the bidder for "Volleyball, Basketball & Badminton Courts , Hockey & Football Play Grounds" as listed in Schedule `A' Part-XI *Above/below the lump sum price inserted by the MES in Schedule `A' Part-XII.

Lump Sum price worked out by the the bidder for Schedule `A' Part-XIII (MISCELLANEOUS) (rate against Srl No.13.01 to 13.77 shall be quoted by the Bidder)

M&L for continious edging with 40mm to 50 mm thick roughly hammer dressed stone, with width 450 mm laid dry on edge vertically (length of stone edging shall not be less than 600 mm).

S&F Cat Eye at the location as directed by Eng-in-Charge of temperature resistance polycarbonate body with scratch and abrasion resistant micro prismtic polycarbonate lence ultrasonically welded with yellow colour body and dark yellow card lences, laid/ fixed on road surface by applying approximately 100 gm of epoxy mixture and placing the cats eye without applying excessive pressure and additionally fixed by shankes by drilling holes in center of cat eye and fixed firmly complete all as specified and directed.

M&L for cleaning and preparing the road surfaces for road marking with reflective thermoplastic white/yellow road marking paint conforming to B/S 3262 laid down through road marking machine in a layer of CRYSTALEX using material @ 5 kg/ sqm by incorporating the white glass beads foe reflectively complete all as specified and directed.

S&F 2.0mm thick aluminum sheet duly framed with mild steel angle iron 40mm x40mm x5mm size with the help of stainless steel nuts/bolts/aluminum rivets with front faces of aluminum sheet to be fully covered by blue diamond grade Micro Prismatic Type IX ASTM D-4956-01 standard Retro Reflective Sheeting material by overlay with coloured film pasted over blue prismatic sheeting and back side painted with grey epoxy paint complete all as specified and directed.

Supply and Install, testing and commissioning of Solar Water Heating System with FPC (flate plate collector) techonology with electrical bachup as per manufacture specification suitable for singhle phas 220V, AC supply compelet FPC type collector, hot water tank, stands etc. of capacity 300 ltr/day with 2 KW electrical back up as per the following specification. Collector : Collector 300 LPD FPC type with suitable Nos of vertical evacuated tubes, duly installed on angel iron frame, transmitance of cover glass tubes 85%, reflectance of glass tubes more than 85%, absorbance of glass tubes 92%, type of coating (Cu/A/SS) and reflectance of coating as recommended by manufcactorere having wind resistance up to 100 km/hr and having average thermal efficiency 58.76% and maximum rise in temp 53.04 deg C (in 24 hours) without night losses fixed at angle of inclination from hrizontal as per recommendation of manufacturer, hot water tank of 300 ltr capacity with 2 KW electrical back up made out of staineless steel sheet not less than 0.5 mm thick duly insulated with puff insulation 50mm thick having density mot less than 36 kg having thermal conductivity 0.29 m/k duly covered with PPGI cladding fixed with temperature gauge, inlet and outlet valves of suitable size duly installed on staging fabricated out of MS angle of appropriate size as recommended by manufacturer duly fixed properly and painted with two coates of anti corrosive paint over a coat of red oxide primer complete all as specified and directed. Note for item No 13.05, 13.06 & 13.07 : (i) MS staging and puff insulated water storage tank for cold water, hot and cold water pipe including valves (to and from system), insulation to pipe and valves to be measured and paid separately. (ii) Any other item required for successfully operation of system is deemed to be included in overall cost quoted. (iii) Make of system : INTER SOLAR/SUN MAGIC/BIPIN INDUSTRIES/TATA BP SOLAR/BORO SOLAR/VENUS (IV) System shall be installed and commissioned by authorized rep of firm supplying the solar water Heating system. (v) Stands for mounting of collector and hot water tank are included in over all cost quoted.

All as per item No. 13.05 above but for capacity 200 ltrs/day.

All as per item No. 13.05 above but for capacity 100 ltrs/day.

Supply, installation, commissioing of double door refrigerator, electric driven (single phase), 240 volts, 50 Hz of capacity 350 Litres all as specified and directed. BEE 5 star rated.

Supply, installation, commissioing of double door refrigerator, electric driven (single phase), 240 volts, 50 Hz of capacity 310 Litres all as specified and directed. BEE 5 star rated.

Supply, installation, commissioing of double door refrigerator, electric driven (single phase), 240 volts, 50 Hz, of capacity 210 Litres all as specified and directed. BEE 5 star rated.

Supply, installation, commissioing of double door refrigerator, electric driven (single phase), 240 volts, 50 Hz of capacity 190 Litres all as specified and directed. BEE 5 star rated.

Supply, installation, commissioing of double door refrigerator, electric driven (single phase), 240 volts, 50 Hz of capacity 160 Litres all as specified and directed. BEE 5 star rated.

Supply, installation, commissioing of metal double door hard top deep freezer single phase 240 Volts, 50 Hz of capacity 270 Litres all as specified and directed.

Supply, installation, commissioing of metal double door hard top deep freezer single phase 240 Volts, 50 Hz of capacity 210 Litres all as specified and directed.

S&F voltage stablizer for automatic operation, single phase naturally air cooled indoor type 3KVA capacity suitable for wall mounting type single phase -220 Volts 50 Hz AC supply for voltage correction up to 170V to 260 V with 1% tolerance including fixing accessories connection testing etc. complete all as directed.

S&F voltage stablizer for automatic operation, single phase naturally air cooled indoor type 2KVA capacity suitable for wall mounting type single phase -220 Volts 50 Hz AC Supply for voltage correction up to 170V to 260V with 1% tolerance including fixing accessories connection testing etc complete all as directed.

Supply, installation, testing & commissioning split type Air Conditioner capacity 1.5 TR complete with copper condensing tubing designed for outside ambient temp (summer-50 degree celcius, monsoon-32 degree Celcius), inside design ondition (Room temp- 18 degree Celcius-25 Degree Celcius, relative humidity-55% ±5% ) No of air changes 3-4 Per hour, copper refrigerant piping with insulation (EP foam pipe section) upto 3.0m from indoor unit to outdoor unit with copper power cable upto 4.0m, 5 Star rated complete with cordless remote control unit confirming to latest BIS standard including supply and fixing/grouted with best quality mounting brackets for outdoor unit complete all as directed.

S&F wall mounted type line-voltage stablizer of capacity 5 KVA for automatic operation, single phase naturally air cooled indoor type and designed for inpur variation between 170 V to 250V with out put voltage stablized at 230 V with accuracy of +2.5% speed of correction 8 V per second complete all as directed.

S&F Steel body, desert cooler electric driven (single phase), having nominal air flow capacity of 4000 Cum per hour (or nearest size).

Supply and laying in trenches, jointing and testing ductile iron (DI) pressure pipes with spigot and socket ends (S/S) including specials class "K-9" 150mm dia cinfirming to IS:8329/2000 in standared length, jointed with cement mortar lining inside the pipes with outside zinc coating with finished layer of BLACK BITUMEN/BLUE EPOXY SYNTHETIC RESIN. Note: Rubber gasket joints shall be measured & paid separately under respective item of Sch 'A '

Supply and laying in trenches, jointing and testing ductile iron (DI) pressure pipes with spigot and socket ends, (S/S) including specials class "K-7" 100mm dia conforming to IS:8329/2000 in standared length, jointed with cement mortar lining inside the pipes with outside zinc coating with finished layer of BLACK BITUMEN/BLUE EPOXY SYNTHETIC RESIN. Note: Rubber gasket joints shall be measured & paid separately under respective item of this Sch 'A '

Supply and laying in trenches, jointing and testing ductile iron (DI) pressure pipes with spigot and socket ends, (S/S) including specials class "K-7" 80mm dia cinfirming to IS:8329/2000 in standared length, jointed with cement mortar lining inside the pipes with outside zinc coating with finished layer of BLACK BITUMEN/BLUE EPOXY SYNTHETIC RESIN. Note: Rubber gasket joints shall be measured & paid separately under respective item of this Sch 'A

S&F and connecting ductile iron fitting such as bands collars, reducers tee pieces, (single or double branch), angle/reducer any type complete.

M&L for construction of brick masonry valve chamber of internal dimension of size 600mm x 600mm x 600mm with PCC (1:2:4) type B1, using 20 graded crushed stone aggredgate as in foudation brick masonry with one brick thick wall in CM (1:4), coping with PCC (1:2:4), type B1, 15 mm thick internal plastering and external wall plaster upto 150 mm below GL in CM (1:4), 50 mm x 50 mm x 6mm size angle iron frame fixed on top of chamber using 4 Nos lugs made of 50mm x 6 mm thick MS flat iron of suitable length, 4.0mm thick mild steel cover for chamber brazed with 50mm x 6mm mild steel flat with locking arrangements, fixed with 200 mm long handle made of 10 mm dia mild steel round bar suitably welded including two coat of cement base pain on plastered surface and two coats of synthetic enamel paint over a coat of red oxide primer on steel surface complete.

M&L for construction of brick masonry valve chamber of internal dimension of size 750mm x 750mm x 750mm with PCC (1:2:4) type B1, using 20 graded crushed stone aggredgate as in foudation brick masonry with one brick thick wall in CM (1:4), coping with PCC (1:2:4), type B1, 15 mm thick internal plastering and external wall plaster upto 150 mm below GL in CM (1:4), 50 mm x 50 mm x 6mm size angle iron frame fixed on top of chamber using 4 Nos lugs made of 50mm x 6 mm thick MS flat iron of suitable length, 4.0mm thick mild steel cover for chamber brazed with 50mm x 6mm mild steel flat with locking arrangements, fixed with 200 mm long handle made of 10 mm dia mild steel round bar suitably welded including two coat of cement base pain on plastered surface and two coats of synthetic enamel paint over a coat of red oxide primer on steel surface complete.

M&L for construction of brick masonry valve chamber of internal dimension of size 900mm x 900mm x 900mm with PCC (1:2:4) type B1, using 20 graded crushed stone aggredgate as in foudation brick masonry with one brick thick wall in CM (1:4), coping with PCC (1:2:4), type B1, 15 mm thick internal plastering and external wall plaster upto 150 mm below GL in CM (1:4), 50 mm x 50 mm x 6mm size angle iron frame fixed on top of chamber using 4 Nos lugs made of 50mm x 6 mm thick MS flat iron of suitable length, 4.0mm thick mild steel cover for chamber brazed with 50mm x 6mm mild steel flat with locking arrangements, fixed with 200 mm long handle made of 10 mm dia mild steel round bar suitably welded including two coat of cement base pain on plastered surface and two coats of synthetic enamel paint over a coat of red oxide primer on steel surface complete.

Supply, install, commissioning, lowering and testing of open well submersible pumping set (suitable for under ground sump), electric driven 415 volts, 3 phase, 50Hz supply, 36.0m head, 17.5 litre per second discharge (LPS) suitable for pump with accessories like contactor, starter protection relay range 13-22 amps etc. complete. Capacity of pump shall not be less than 15 HP.

Supply and install altoch dozing system consisting of 40 ltr-100 ltr PE/FRP tank with lid and level guage along with agitator with shaft and blade in SS-316 (FRP/Epoxy coated)/ plastic mounted on tank all as specified and directed.

Supply MCBs, 'C' curve, ISI marked, 10KA, integrated lable holder, sliding bottom clamp, improved air channels, colour coded. On/Off indication on dolly, biconnect lower terminals, IP 20 protected terminals, sliding shutter, IS-60898-1 2002 of under mentioned type and rating and fixing in DB's ( Catered separately in this schedule ) MCB TPN 32 Amps. Note:- DBs shall be measured & paid separately under respective item of this Sch 'A'

Cutting of existing DI pipe line of 150mm dia bore and inserting Tee of size 150x150x150mm for taking branch connection including necessary joints and fittings complete all as specified and directed by Engr- in-Charge.

S&F, cast iron, HT cable/route indicator of suitable size along HT cable trench including planting in ground with PCC complete all as specified and directed.

S&F Junction Box of size 200 x 160 x 100mm made out of 2mm thick CRCA mild steel sheet, duly painted and fixed with suitable MS clamps, nut bolts including 04 Nos Bus bar supports duly insulated and fixed for terminating 4 core,16 Sqmm aluminium under ground cable including glands etc 1 No MCB SP, 10 KA, 10 Amps all as specified and directed.

S&F IP-66 rated LED street light luminaire 45W, 6000-6500 K, Die Cast Alluminium housing with UV stabilized prismatic acrylic cover with LM-6 alluminium housing. The luminaire should be provided with in built power unit and electronic driver. The luminaire should be so constructed to ensure that the gear and LED modules are replaceable if required. The luminaire should be suitable for side entry with pole diameter of 48mm to 60mm. No additional cooling or ventilation apart from the cooling fins provided along the length on luminaire housing, should be used upto 50 Degree centigrate all as specified and directed.

S&F IP-66 rated LED street light luminaire 60W, 6000-6500 K, Die Cast Alluminium housing with UV stabilized prismatic acrylic cover with LM-6 alluminium housing.The luminaire should be provided with in built power unit and electronic driver. The luminaire should be so constructed to ensure that the gear and LED modules are replaceable if required. The luminaire should be suitable for side entry with pole diameter of 48mm to 60mm. No additional cooling or ventilation apart from the cooling fins provided along the length on luminaire housing, should be used upto 50 Deg C all as specified and directed.

Supply, install, testing and commissioning of factory made CPRI test certified outdoor cubical type panel board made out of 2mm thick CRCA mild steel sheet, duly painted, stand mounted essential/ non essential with timer circuit for the automatic switching ON/OFF the lumanaries and with provision of control circuit for power tool operation complete with ,4 pole MCCB 63 amp 415 volts of 25 KA- 01 Nos, power contractor 3 Ph, 415 V, 50 Hz MNX 70, digital timer switch for LED lights complete all as specified and directed.

S&F IP66, SMD, LED floodlight with pressure Die Cast Aluminium housing complete with all accessories,150 W and unique flood optics all as directed.

Supply, install, testing and commissioning of factory made CPRI test certified outdoor cubical type panel board, stand mounted essential/ non essential with timer circuit for the automatic switching ON/OFF the lumanaries and with provision of control circuit for power tool operation complete with, 4 pole MCCB 63 amp 415 volts of 25 KA - 01 Nos, power contractor 3 Ph, 415 V, 50 Hz MNX 70, digital timer switch for high mast light, including starter moter for lowering and lifting machines of required capacity complete all as specified and directed.

S&F 20 Watt surface/wall mounted LED batten having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed.

S&F, 5 Watt led bulb including lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings, including electrical connection with 3 core flexible copper wire of appropriate size from ceiling rose to the lamp holder all as specified and directed by Engineer-in-Charge.

S&F, 20 Watt LED security/building light having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficacy of ≥ 100 lumen/W, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP 66 protection, high effiency polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, suitable for side entry, pole mounting with bracket arm OD 35 mm to 42 mm including necessary electrical connection to the fixture with 3 core flexible copper conductor cable of appropriate size and 1.5 m long bracket, having 40 mm diameter light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and directed.

S&F, BEE five star rated energy efficient high speed ceiling fan having 1200 mm blade sweep, air flow not less than 210 cum, operating voltage 220-240 V and frequency 50 Hz, including a downroad of suitable size and electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fan complete all as specified and directed.

S&F, engery efficient metalic exhaust fan having blade sweep 300 mm, air delivery not less than 900 Cum, operating voltage 220-240 V and frequency 50 Hz, including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fan complete all as specified and directed.

S&F SP MCB, ISI marked 6 -32 A, 'B' curve for AC supply till 63 A, having breaking capacity Icn = 10 kA, conforming to IS/IEC 60898-1-2002, sliding bottom clamp, colour coded on/off indication on dolly, biconnect IP-20 protected lower terminals and sliding shutters complete all as specified and directed.

All as per item No. 13.53 above but 63 A, SP MCB, 'C' curve.

All as per item No. 13.53 above but 16 A, SPN MCB, 'C' curve.

All as per item No. 13.53 above but 32 A, SPN MCB, 'C' curve.

All as per item No. 13.53 above but 40 A, SPN MCB, 'C' curve.

All as per item No. 13.53 above but 63 A, SPN MCB, 'C' curve.

All as per item No. 13.53 above but 63 A, TP MCB, 'C' curve.

S&F, MCCB 100 A, 16 KA, 4 Pole, thermal magnetic release,Ics=100%,Icu.

S&F, MCCB 63 A, 16 KA, 4 Pole, thermal magnetic release,Ics=100%,Icu.

S&F factory made, verticle distribution board made out of 2mm thick CRCA mild steel sheet duly painted, TPN four way, double door type, protection class IP- 42 suitable for mounting MCCB as incomer and SP MCB as outgoing and DBs conforming to IS-13032, IS-8623, BS-5484.

S&F MCCB TPN of the following capacity, 300 milliseconds sensitivity , ISI marked as per IS 12640-2, as a single complete unit, under mentioned type and rating and fixing in DB'S (Catered Seperately in this schedule):-(NOTE:- Make of the MCCB should be the same as that of DB). MCCB TPN 160 Amps, 16 KA rupturing capacity. Make leegrand Cat Pt No 420010 or equivalent make .

S&F 25mm dia, rigid non-metallic PVC conduit exclusive of boxes (junction terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, locking nuts, saddles, pipe hooks etc.

S&F, testing and commissioning of High Mast Tower of 16.0m height, material of mast is BS EN 10025, polygon >12 sided, maximum 3 sectors, stress fit joints, base dia 410mm, top dia 150mm, section thickness of base 4mm & top 3mm, foundation base plate size 570mmx25mm, foundation bolt 30mm x 850mm, door size 1200x250mm, weather proof, capable for resist wind pressure 180Km/hr as per IS:875 Part-3, safety factor 1.25 complete with suitable mast carrier, insulated copper cable of 5 core x 4.0 Sqmm, stainless steel wire-rope (two Nos) of dia 6.0mm with drum gearbox suitable cap motor & manual handle etc. complete including the 8 Nos 250W LED high intensity energy efficient, LED flood light for high mast tower, chip efficient > 140Im/w, pf>0.95, CCT 5000K-6500K, CRI>80, beam angle 60-90 degree, die cast LM6 body powder coated anodized aluminium reflector, toughened glass with gasket, working voltage 140-280V, 50Hz, surge voltage/open & short circuit protection, IP-65 conforming to IS:10322 & IS 13383. including feeder pillar (control panel), outdoor type, suitable for above High Mast Tower light, consisting of timer switch for auto ON/OFF, contactors, MCBs, V-meter, A-meter, auto/manual, Rev/Fwd buttons/switches for carrier motor etc. and provn of foundation complete as recommended by manufacturer and all as directed..

M&L for 10 Sqmm x 3 core, 1100 volt grade flat copper conductor cable, submersible PVC insulated water proof conforming to IS specifications complete all as specified and directed.

S&F and lowering flange type mild steel column pipe (medium grade) confirming to IS specifications, of size 80 mm dia bore (approx 3.0m long), both ends flanged/ drilled by welding with special provision such as MS clamps and mild steel flange all as specified and directed.

Cutting 150mm bore dia pipe for inter connection of delivery pipe of non clog submersible pump set including leak proof welding for complete all as specified and directed.

S&F 24W, 2'x2' surface/ wall mounted, LED Decorative light extruded aluminum housing with PC diffuser and integrated electronic driver with high efficiency long life LED chips, CRI > 80, power factor > 0.95, system luminous efficiency > 100, having average life 50000 hrs, operating voltage 140-270, including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the LED batten fitting complete all as specified and directed.

S&F punched tape concertina coil/ Razor wire concertina coil, dia 610mm (having 50 Nos spiral turns, weight shall not be less than 9.0Kg and one coil (i.e. 50 spiral shall not be stretched more than 6.0m), tied with GI staples and GI clips to retain in horizontal position including necessary bolting or tied to GI birbed wire or angle iron etc. complete all as specified and as directed.

Same as above item no. 13.72 but for One fan /exhaust point controlled by one switch.

Same as above item no. 13.72 but for One 6 Amp socket outlet Independent board controlled by one switch

Same as above item no. 13.72 but for One 6 Amp socket outlet for same board controlled by one switch.

Same as above item no. 13.72 but for One 16 Amp socket on independent board but with 2.5 sqmm 2 core & 1 earth controlled by one switch

S&F 9W, mirror light having indirect up/down light for miror and as wall light application with CCT 6000K, including LED bulbs /module and electrical connection with 3 core flexible, copper conductor cable of appropriate size from ceiling rose to the LED battern fitting complete all as specified and directed.

FRIZO INDIA PVT LTD

M/s Madan Lal Bansal and Co. Contractors Pvt. Ltd.

Komal Buildcon Pvt. Ltd.

DES RAJ AND SONS BUILDERS PVT LTD

N A Construction Pvt Ltd

AYG Realty Pvt. Ltd.

Som Projects Pvt Ltd