CERTAIN REPAIR TO BIRD PROOFING STEEL DOORS FLOORING ETC AT SOUTH SIDE IN TECH AREA AT AF JODHPUR

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and removing the demolished material or debries out side MoD land complete all as specified & directed by the Engineer-in-Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of old unserviceable, rusted, broken (corrugated/semi corrugated, etc.) asbestos cement sheets in ridge and roof coverings complete all as specified and as directed by the Engineer-in-Charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc Laid, bedded and pointed in any mortar complete all as specified and as directed.

Supply and fixing bird proof net of co-polymer nylon monofilament, ultraviolet stabilized with apertute 20mm x 20mm, the thickness of filament is 0.80 mm, melting point 260 degree, tension force can resist 23.08 kgs, dia of nylon thread not less than 1.25 mm fixed in position as per manufacturer's instructions including dismantling old existing destroyed unserviceable nylon deteriorated net at any height in ceiling including making good the disturbed surface complete all as specified and as directed by the Engineer-in-Charge. Note :- Quoted rates shall be deemed to be included for working in building/structure of upto 10 metre height.

Supply and fixing bird proof net in patch work of size not exceeding 1 sqm each, at any location and at any height, with bird proof net of co-polymer nylon monofilament, ultraviolet stabilized with apertute 20mm x 20mm, the thickness of filament is 0.80 mm, melting point 260 degree, tension force can resist 23.08 kgs, dia of nylon thread not less than 1.25 mm fixed in position as per manufacturer's instructions including dismantling old existing destroyed unserviceable nylon deteriorated net at any height in ceiling including making good the disturbed surface complete all as specified and as directed by the Engineer-in-Charge. Note :- Quoted rates shall be deemed to be included for working in building/structure of upto 10 metre height.

S&F in repair wire netting of stainless steel wire not less than 0.90 mm dia and size of square mesh 20 mm x 20 mm fixed with tinned tacks of stainless steel wire staples fixing in vertical/ceiling position complete all as specified and directed Note :- Quoted rates shall be deemed to be included for working in building/structure of upto 10 metre height.

Material and labour for oiling and greasing top and bottom pullies of each steel sliding hanger door shutter (each panel), cleaning with using standard thinner such as carbon tetra chloride/ Benzene and making smooth functioning to reduce the friction of door and make the door functional to the entire satisfaction of Engineer-in-Charge. Note :- Quoted rates shall deemed to be included for working in building/structure of any height.

Supply & fixing in repairs MS pulley of dia 180 mm to 300 mm with bearing shaft, nuts, bolts including making necessary arrangement for taking down old pulley at the bottom of sliding hanger door shutter complete all as specifed and directed. Note :- (i) Quoted rates shall deemed to be included for working in building/structure of any height. (ii) Quoted rates shall deemed to be included taking down of hanger door leaf for repair and refixing in original position.

Supply & fixing in repairs MS pulley of dia upto 180 mm with bearing shaft, nuts, bolts including making necessary arrangement for taking down old pulley at the top of sliding hanger door shutter complete all as specifed and directed. Note :- (i) Quoted rates shall deemed to be included for working in building/structure of any height. (ii) Quoted rates shall deemed to be included taking down of hanger door leaf for repair and refixing in original position.

S&F in repairs 5 mm thick PVC acrylic sheet in square or rectangle in each pane fix in window/ventilator of hanger/bldg by fixed with necessary joining cleats glazing clips, rubber packing, aluminium snap beading, screws etc complete all as specified and as directed by Engr-in-Charge Note :- (i) Quoted rates shall deemed to be included for working in building/structure of any height.

Material & labour for preparation of old steel surface of any description over 10 cm width and girth, not otherwise described and applying two coats of aluminium paint complete all as specified & directed by the Engineer-in-Charge.

M&L for Vitrified light shade coloured tiles 9-10 mm thick double charged (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 1.00 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in cement mortor 1:6 complete all as specifed and directed.

M&L for Vitrified light shade coloured tiles 9-10 mm thick double charged (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 1.00 sqm in skirting etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick plastering in CM 1:4 as in backing coat of tiles complete all as specifed and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate in sub floors complete all as specified and as directed.

M&L for factory made vitrified heavy duty coloured parking tiles, matt finish, unglazed and unpolished of size 300x300x10mm thick laid over and including 15 mm thick screed bed in CM (1:4) complete all as specified and as directed.

M&L for 75 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregates as in sub base complete all as specified and as directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for granite of 18 to 20mm thick, work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including screed layer of 15 mm thick in CM 1:6 including grinding and polishing complete all as specified and as directed.

Supply & fixing factory made Steel rolling shutters with laths of thickness 1 mm, without ball bearing, as specified including top cover, anchoring rod, hasp and staple, erected in position as indicated, push, pull or manual type/gear operated type with bevel gear box and crank handle including taking down existing old unserviceable, broken, rusted steel rolling shutter of any size and type complete all as specified and as directed.

Taking down carefully hood and steel rolling shutter of size not exceeding 10 sqm and replacement of unserviceable/defective parts and refixing in the same opening after cleaning of guide rails, laths, top cover by kerosene and proper greasing, oiling, replacement of rusted nut bolts etc, removing of bend, alignment etc to make the system smooth functional & making good the disturbed surface all as specified & directed by Engineer-in-Charge. Note :- (i) The unserviceable parts to be replaced shall be measured and paid for separately as "Supply only". (ii) Quoted rate shall be inclusive of providing missing nuts bolts, greasing, oiling, denting, tension to spring etc.

Taking down carefully hood and steel rolling shutter of size exceeding 10 Sqm but not exceeding 25 sqm and replacement of unserviceable/defective parts and refixing in the same opening after cleaning of guide rails, laths, top cover by kerosene and proper greasing, oiling, replacement of rusted nut bolts etc, removing of bend, alignment etc to make the system smooth functional & making good the disturbed surface all as specified & directed by Engineer-in-Charge. Note :- (i) The unserviceable parts to be replaced shall be measured and paid for separately as "Supply only". (ii) Quoted rate shall be inclusive of providing missing nuts bolts, greasing, oiling, denting, tension to spring etc.

Supply only MS sheet hood cover of 1.00mm thick bent to shape match with existing brackets including stiffners of MS angles/flat complete all as specified and directed.

Supply and fixing in repairs gear box of steel rolling shutter Including handle rack & pinion system, bearing etc of rolling shuter size exceeding 5 Sqm but not exceeding 25 sqm each complete all as specified & directed by Engineer-in-Charge.

Supply only helical wire rolling spring suitable for rolling shutter of area not exceeding 15 sqm each complete all as specified and directed.

Supply only helical wire rolling spring suitable for rolling shutter of area exceeding 15 Sqm but not exceeding 25 sqm each complete all as specified and directed.

S&F in repair for Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete including painting with two coats of synthetic enamel paint over and inluding one coat of red oxide primer complete all as directed by Engineer-in-Charge.

M&L for cleaning and greasing the top and bottom guide rails of MS sliding door complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise discribed, and applying two coats of synthetic enamel paint over and including a coat of red oxide primer all as specified and as directed.

M&L for PCC 1:3:6, type C-2 using 40 mm graded stone aggregate as in foundation filling or mass concrete complete all as specified and as directed.

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; door, barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks & similar work conforming to Fe 290-0 Gde E-165 including dismanting old unserviceable MS work complete all as specified and as directed by Engr-in-Charge.

GB Group & Co

D DEV COMPANY

Om Trading Corporation

VIKAS CONSTRUCTION CO.

Keystone Constructionare