CA GE(N)AMB-23/2024-24 PETTY REPAIR/DAY TO DAY MAINT WORKS INCL REPAIR/REPLACEMENT TO JOINERY, PLUMBING, SANITARY, ROOF, PLASTERING AND ALLIED CONNECTED BLDG REPAIR WORKS IN OFFR MD ACCN-II AND OTHER AREA OF SEC B UNDER AGE B/R-I OF GE (N) AMBALA

Amount

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key scrubbing down with water, etc. complete all as specified and as directed by the Engineer-in-Charge

M & L rendering 15 mm thick on brick work or concrete wall surfaces in cement mortar 1:4 including mixing water proofing compound @ 2% by weight of cement or as per manufacturer's instruction and finished fair and even without using extra cement Upto a height of double storey including parapet, complete all as specified and as directed by the Engineer-in-Charge. ( Note- The cost of providing WPC shall be included in quoted rate under this item )

Material and labour for rendering 10 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:6 and finishing the surface even and smooth without using extra cement upto a height of double storey including parapet, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering (in patches) 05 mm thick on fair faces of brick work or concrete ceiling surfaces, chajjas, etc. in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine stone aggregate of size between 6 to 12 mm as per the texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered/unplastered surfaces of walls, chajjas, roof projection, etc. and applying two coats of cement base paint over a coat of chalk whiting complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of newly plastered/ unplastered surfaces of walls and applying two coats of oil bound distemper with painting roller over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces over a coat of chalk whiting complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered/unplastered surfaces and applying three coats of white lime wash on surfaces of ceiling, chajjas, roof projection complete all as specified and as directed by the Engineer-in-Charge.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar, etc. but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Non Skid coloured ceramic tiles joint free premium/1st quality 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Non Skid coloured ceramic tiles joint free premium/1st quality 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for glazed ceramic coloured tiles joint free premium/1st quality in vertical surfaces/skirtings/dados of size 300x600 x7-8mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for glazed ceramic coloured tiles joint free premium/1st quality in vertical surfaces/skirtings/dados of size 300x450 x7-8mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for vitrified ceramic double charged light shade tiles, premium quality, (square/rectangular), 10mm thick, area of each tile exceeding 0.42 sqm and not exc 1.00 sqm as in floor, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for vitrified ceramic double charged light shade tiles, premium quality, (square/rectangular), 10mm thick, of same description as of floor tiles in serial item No. 18 above but 100mm to 200mm height as in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including rendering 10 mm thick in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete in ground floor and pavings not exceeding 15cm thickness (below or above ground level) and removal the rubbish/ demolished material outside defence land, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for providing 75 mm thick cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base and finished even and fair without using extra cement including form work where ever required complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 25 mm thick PCC 1:2:4, type B0 as in sub base of floor (using 12.50mm graded crushed stone aggregate), finished even & fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge. Note- This item shall not be executed in the location, where dismantling of tiles work have been done.

M & L providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (not exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight including form work complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in horizontal surface of steps, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 incl rounding of front edge complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rounding to edges of stone slab, both edge with grinder as in kitchen slab, steps and similar situations etc. complete all as specified and as directed by the Engineer-in-Charge.

Cutting chases to brick wall built in cement mortar, pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

Material and labour galvanised iron tubing 20 mm bore, ISI marked, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

Material and labour for galvanised iron tubing 15mm bore, ISI marked, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixed (in repair), stop valves, 15 mm dia pipe, brass chromium plated, fancy type, ISI marked, screwed down, high pressure with capstan head, (concealed type) with long shank and cup, screwed both ends for iron pipes or for unions, complete all as specified and as directed by the Engineer-in-Charge. (Note : Weight of stop valve shall not be less than 0.575 Kg)

Supply and fixing as in repair 15mm bore cast copper alloy chromium plated angular stop valves, ISI marked, screwed down, high pressure with capstan head, screwed down both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair fancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, ISI marked, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair bib taps 15mm bore fancy type brass chromium plated with long body, ISI marked, wall flanges and capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair brass chromium plated WHB mixer or sink mixer for mixing hot & cold water for 15mm bore pipes including all connecting fittings, screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing PVC connections 15 mm size with PTMT nuts of length 600 mm as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of vitreous china wash hand basin white with pedestal, ISI marked, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling chromium plated and 32 mm dia PVC waste pipe including fixing of waste fitting, etc. as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixed as in repair fancy type, shower rose 125mm size with shower arm 195mm , brass Chromium plated, revolving type, fixed to existing steel pipe or union 15mm bore complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing for vitreous china wash down water closet pan (pedestal pattern), including 'P' or 'S' trap white (including fixing bolts but excluding flushing cistern and flush pipe) including plastic water closet seat white closed pattern with flat bottom cover and mild steel chromium plated or aluminium hinges device as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of brass chromium plated hand shower ( health faucut) with 8 mm dia 1.2 mtr long flexible tube and wall hook with NRV ( back flow preventer )complete fixed to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in replacement 10 litre PVC valveless syphonic action type flushing cistern with inlet ball valve float, handle, etc. with and including brackets, flush pipe, etc. and connections of flush pipes to WC complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair stainless steel grating doom 125 mm dia with or without waste hole complete all as specified and as directed by the Engineer-in-Charge

S & F as in repair stainless steel grating doom 100 mm dia with or without waste hole complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing of sinks with drainage board made out of stainless steel 1mm thick sheet for kitchen with plugs, waste pipe, brass chromium plated coupling and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm as in repair complete all as specified and as directed by the Engineer-in-Charge

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer–in–Charge.

Supply and fixing of brass chromium plated Soap Dish Holder including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of brass chromium plated toilet paper holder including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 15 mm bore Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F 20 mm bore Gun–metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe as in repair , complete all as specified and as directed.

Supply and fixing water storage tank, 500 litre capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm bore high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore, complete all as specified and as directed.

Supply and fixing water storage tank, 1000 litre capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm bore high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore, complete all as specified and as directed.

Material and labour for 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement as in repair complete all as specified and as directed.

Demolition and breaking up drain pipes 75/100 mm dia, SGSW, AC, PVC, reinforced concrete pipe including fittings, in any position complete all as specified and as directed

Supply and fixing of 110mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in trenches, complete all as specified and directed by the Engineer-in-Charge..(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 110 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 110 mm bore UPVC (SWR) Tee with access door, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 75mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and as directed by the Engineer-in-Charge. .(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 75 mm bore UPVC (SWR) Tee with access door, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 75 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified and as directed by the Engineer-in-Charge. . (Note- UPVC bends shall be confirm to BS 4515 DIN 19531 and DIN 19534)

Supply and Fixing with stack clamps 50mmx5mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing end of stays to wall or roof for 100/110 mm pipe, complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing of plastic water closet seat cover , white closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminised hinging device as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair vitreous china table top wash hand basin white, of size 565mmx420mmx140mm fixed on and including cantilever bracket 32mm dia brass waste coupling and 32 mm dia PVC corrugated waste pipe not less than 900 mm long including fixing of waste fitting etc complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of stainless steel fancy type peg set ( each peg having 5 Nos hook) and fixed with stainless steel screws and PVC rawal plug as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of brass chromium plated Towel ring round including fixing with brass screws complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 32 mm dia PVC waste pipe for wash hand basin / Kitchen sink etc. of standard length as in repair complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutter area not exceeding 1.50 Square metre (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutter area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description area exceeding 01 sqm but not exc 2 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-290-W (Gde E-165) quality 'A' complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for factory made 2nd class hard wood 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both face . The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be kiln seasoned and chemically pressure treated) complete all as specified and as directed by the Engineer-in-Charge.

S&F powder coated aluminium section (minimum thickness of powder coating 50 micron) work for doors,windows & ventilators frames with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge. Note : (a). Weight of aluminium sections shall be as per IS or actual weight which ever less shall be measured. (b). The rates quoted shall be inclusive of neoprene beading, jointing clips, screws, etc as required and the same shall not be measured for arriving the weight;

S&F powder coated aluminium section (minimum thickness of powder coating 50 micron) for doors,windows & ventilators shutters including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge. Note : (a). Glazing shall be measured and paid separately; (b). Weight of aluminium sections shall be as per IS or actual weight which ever less shall be measured. (c). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required and the same shall not be measured for arriving the weight; (d). The rates shall be inclusive of locking arrangement including complete packing with silicon gel alround contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed.

S & F anodised aluminium grill (anodized transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section and fixed to the window frame with C.P brass/ stainless steel screws @ 200 mm center to center, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized aluminium standard section around the opening, complete all as specified and as directed by the Engineer-in-Charge.

S & F 125 x 60mm size, 01 mm thick MS pressed steel frames for windows with two rebates including necessary fixing lugs, hinges, holes for tower bolts incl bolt strike plate, etc., complete all as specified and as directed.

S & F 125 x 60mm size, 01 mm thick MS pressed steel mullion for windows with two rebates including necessary fixing lugs, hinges, holes for tower bolts incl bolt strike plate, etc., complete all as specified and as directed.

S&F steel window shutters glazed and gauged using ERW hollow 'P' section with side hung shutter including projectind type hinges, steel handles and steel peg stay, 2 nos 150mm long towel in each shutter complete with glazing bars dovetailed or welded, incl shop coat of red oxide primer as specified complete all as specified. (Ref TD–219(c) sheet 1/3 to 3/3) Note : Guard bars incl 40x3mm size FI & its painting will be measured separately.

S&F steel window shutters glazed and gauged using ERW hollow 'P' section with side hung shutter including projectind type hinges, steel handles and steel peg stay, 2 nos 150mm long towel in each shutter complete but with out glazing bars dovetailed or welded, incl shop coat of red oxide primer as specified complete all as specified. (Ref TD–219(c) sheet 1/3 to 3/3) Note : Guard bars incl 40x3mm size FI & its painting will be measured separately.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

Supply and fixing of factory made solid PVC moulded door shutters with particle board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick prelaminated moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for PCC 1:3:6 type C-0 using 12.50mm graded crushed stone aggregate as in holdfasts etc. complete all as specified and as directed.

S&F mild steel flat iron as in hold fast clamps articles conforming to Fe–290 Gde E–165, complete, all as specified and as directed

Supply and fixing of butt hinges 100mm long of mild steel, medium weight, complete all as specified and as directed.

Supply and fixing of 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

Supply and fixing of 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed as in repair complete all as specified and as directed.

Supply and fixing of 150 mm long aluminium handle cast type anodised complete all as specified and as directed.

Supply and fixing of 300mm long aluminium alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloys to door shutter as in repair complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds and steel window frame glazed with putty or fixed with beads complete all as specified and as directed.

Material and labour for sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters,complete all as specified and as directed.

Material and labour for 3mm thick glass ground or obscured or frosted on one side, in square not exceeding 0.5 sqm in each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters,complete all as specified and as directed.

Material and labour for sheet glass 4.8mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters,complete all as specified and as directed.

Material and labour for 4.8 mm thick glass ground or obscured or frosted on one side, in square not exceeding 0.5 sqm in each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters,complete all as specified and as directed.

Supply and fixing of stainless steel wire cloths 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple, complete all as specified and as directed.

Supply and fixing as in repair stainless steel wire cloths 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified and as directed.

S&F mild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and as directed.

S&F hydraulically regulated, universal type door closer suitable for door shutters of width 851mm to 1000mm, mild steel body complete incl welding if required, all as specified and directed.

S&F in repair hydraulically regulated, universal type door closer suitable for door shutters of width 851mm to 1000mm, mild steel body complete incl welding if required, all as specified and directed.

Supply and fixing of 250mm long aluminium alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloys to door shutter complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair stainless steel tubing of 25 mm dia min 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets,finials or end piece, fancy type, fixed with 30x8 SS screws etc complete all as specified and as directed by the Engineer–in–Charge. Note : For the purpose of payment running length of curtain rod only shall be considered.

Material and labour for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete in existing sunken floor etc and removal of the same to a distance exceeding 250 mtr and not exceeding 500 mtr, depostied where directed complete all as specified and as directed by the Engineer-in-Charge.

S&F medium grade GI tubing of size 40mm dia as in spouts as in repair complete all as specified and as directed by Engineer-in-Charge

M&L PCC 1:5:10 type E-2, using 40 mm graded crushed stone aggregate as in filling in sunken floor, rounded or chamfered on edges complete all as specified.as directed by the Engineer-in-Charge.

M & L providing cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate as in padding, levelling course, etc. and surfaces finished even and smooth without using extra cement including form work where ever required complete all as specified and as directed by the Engineer-in-Charge.

M&L for sunken floor water proofing treatment complete all as under :– (A) Scrapping the surface with wire brush and cleaning with water and allow to dry. (B) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound. (C) 15 mm thick cement plaster 1:3 mixed with water proofing compound as per manufacture instruction (the corner will made rounded in concave shape). (D) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound. (E) Apply one coat of hot bitumin grade 85/25 conforming to IS 702 @ 1.2 kg/sqm. (F) Supply and laying APP with non woven polyster reinforced sheet 3mm thick weight not less than 3.00 kg/sqm. (G) Applying one coat of hot blown bitumin grade 85/25 conforming to IS–702 @1.20 kg/sqm. (H) Curing the sunken portion with water min 48 hours by ponding. (J) Fixing 50mm bore GI pipe medium grade as in spout of 0.60 mtr length in each sunken.

Demolition of mud in roofs, any thickness, including plastering and leaping (whether full thickness removed or only a part thereof) complete all as specified and as directed by the Engineer-in-Charge.

M & L providing cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in padding, levelling course, etc. and surfaces finished even and smooth without using extra cement including form work where ever required complete all as specified and as directed by the Engineer-in-Charge.

Material & Labour for providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt and consisting of a coat bitumious primer @ 0.40 litre /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25 degree centegrate temprature and viscosity 70-160 cps over the primer coat with overlap of 100mm at the side and 150mm at the end, the layer membrane shall be laid using butane gas torch and sealing all joints etc. after preparing the surface complete as per standred practice as per manufacture's instructions . The vital physical and chemical parameters of the membrane shall be under ;- (i) Joint strength in longitudinal and transverse direction at 23 degree centegrate at 650/ 450 N /5 cms (ii) Tear strength in longitudinal and transverse direction at 300/250N/5 cms. Softing point of membrane not less then 150 degree centegrate when tested in accordance with ASTM (d-5147) (iii) The laying of membrane shall be got down through the authorised applicator of manufactures of membrane only complete all as specified and as directed by the Engineer-in-Charge.

M&L for providing and laying in small patches n.exc 1Sqm each using 3mm thick APP (atactric polypropylenepolymer) modified prefabricated five layer weight not less then 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt, make as approved consisting of a coat bitumious primer @ 0.40 ltr /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25'C temprature and viscosity 70–160 cps over the primer coat, the layer membrane shell be laid using butane troch and sealing all joints etc after preparing the surface complete as per standred practic as per manufactures instructions.

Cutting openings, through 230mm thick brick walls built in cement mortar for window and other openings n.exc 0.50 Sqm in area or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including repairing the cill & jambs in cement plaster 1:4 incl providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m

S&F for cement concrete tiles 30cm x 30cm x 20mm thick, machine pressed, set jointed and pointed in neat cement slurry in roofs, laid in CM (1:6) 15 mm thick and jointed flush in CM (1:3) mixed with 5% crude oil by weight of cement including dismantling of unsv tiles, complete all as specified and as directed.

M & L cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed.

Demolition of reinforced cement concrete as in shelves, lintles etc n exc 15 cm thickness (below or above ground level), complete all as specified and as directed.

M & L reinforced cement concrete (1:2:4) (Nominal Mix) using 20mm graded crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed.

Formwork to soffits of suspended slabs such roof slab, floor slabs, landings and similar work not exceeding 20 CM thick (horizontal or sloping) flat for rough finished surfaces of concrete , complete all as specified and as directed.

M&L TMT steel bars 10mm dia and over cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia, complete all as specified and as directed.

Dismantling boarding of any type/size as in cup board/wardrobes etc , fixed in any position with nails including hardware, wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs any thickness, including cover fillets, complete all as specified and as directed.

Supply and fixing of continuous (piano) hinges , width of flaps 40mm (when open) mild steel bright finish or electro galvanised, complete all as specified and as directed.

S & F 100mm Hasp and staple, safety type, aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and as directed.

Supply and fixing of 100 mm long fancy type brass handle, cast type, polished bright, complete all as specified and as directed.

S & F in rep ball catches with 8mm dia steel ball, and brass body or magnetic catcher with striking plate including letting in and fixed, complete all as specified and as directed.

Supply and fixing of continuous (piano) hinges , width of flaps 30mm (when open) mild steel bright finish or electro galvanised, complete all as specified and as directed.

S&F in repair glass corner shelf (set of three) 8mm thick including CP railing radius 250mm, complete all as specified and as directed.

S&F in repair cabinet type looking mirror, size 450 mm x 600 mm, box type including all as necessary items complete all as specified and as directed by the Engineer–in–Charge. Make : Prayag Cat NO.555 or equivalent as per appendix 'B' of Makes.

S&F in repair single piece water closet wtih integrated cistern (twin flush), PP soft close seat cover, hinges, fixing accessories and accessories set, cistern fittings 'S' or 'P' Trap complete fixed as in repair, complete all as specified and as directed. Make : PRAYAG Cat part NO. 4256 /Cera Cat part No.S10131095 /Hindware Cat Part No.92099 (S–30)

S&F in repair stainless steel kitchen plate rack made out of 0.63mm thick stainless steel of grade SS304 of size 24"x30"x10" including screws and fixing arrangements complete all as specified and directed. Make : PRAYAG Cat part NO. P-430 or equivalent in Bluestar /Nirali /Prima

S&F in repair stainless steel 304 grade wall mounted towel rack with lower hanging towel hooks 600 mm long and 250mm wide between flanges including brackets complete all as specified. Make : PRAYAG Cat part NO. GBA 133 or equivalent in SOMANY/JAQUAR/HINDWARE/Parryware /Prima

S&F in repair brass CP wall mixer 3–in–1 (with over head shower and telephonic shower) for mixing hot & cold water for 15mm bore dia, pipes, screwed down for iron pipe with connected leg with wall flange & wall bracket for hand shower and fixed complete all as specified and directed.

S&F for LEAD FREE PVC Celuka ply 18mm thick (Minimum density 650kg/Cum) of both side plain white colour, fixed with stainless steel screws, solvent cement /adhesive to make kitchen /bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications, complete all as specified and as directed.

S&F for LEAD FREE PVC Celuka ply 18mm thick (Minimum density 650kg/Cum) of single side rigid lamination of approved colour and other side plain white colour, fixed with stainless steel screws, solvent cement /adhesive to make kitchen cabinet shutters and shelves complete as per manufacturer’s specifications, complete all as specified and as directed.

S&F for 24mm thick LEAD FREE PVC Celuka ply (Minimum density 650kg/Cum) of single side rigid lamination of approved colour and other side plain white colour fixed with stainless steel screws, solvent cement /adhesive as in shutters of kitchen cabinet/CB and pull out drawer visible side complete as per manufacturer’s specifications, complete all as specified and as directed.

S&F in repair stainless steel 304 grade wire basket of size 386 x 500 x 100mm premium quality fixed in position complete all as specified and directed by Engr–in–Charge. Make : HETTICH, KAFF, GLEN, HARRISON or GODREJ.

S&F in repair stainless steel 304 grade wire basket of size 386 x 500 x 150mm (plain basket) premium quality fixed in position complete all as specified and directed by Engr–in–Charge. Make : HETTICH, KAFF, GLEN, HARRISON or GODREJ.

S&F in repair stainless steel 304 grade wire basket of size 386 x 500 x 200mm (for plates) premium quality fixed in position complete all as specified and directed by Engr–in–Charge. Make : HETTICH, KAFF, GLEN, HARRISON or GODREJ.

S&F in repair Ball bearing runners 450mm telescopic (KA4732) full extension load capacity minimum 35Kgs complete all as specified and directed by Engr–in–Charge. Make : HETTICH, KAFF, GLEN, HARRISON or GODREJ.

Attending and rectify day to day complaints of broken pcc floor, plinth, plaster, painting, etc requiring max 1Kg cement with sand for rep of masonry work /items and carrying out minor repairs such as edges of plinth protection, plaster in patches n exc 1 sqm etc, including other petty repairs using material like sand, cement & aggregate to make it functional /useable complete all as specified and directed by Engineer–in–Charge. (Note : Any other items except mentioned in this item or major repair, if required, the same shall be measured and paid for separately under respective items)

M&L for Cleaning of sewage line upto first man holes by any means and removing blockage of WC, EWC, Bathroom, floor trap of WHB/Kitchen pipe etc including first man hole, complete all as specified and as directed.

Note for Item No. 138 and 139:- (i) Contractor or his authorised rep will report daily at 0900 hrs and onwards at complaint cell for collection of complaints from the concerned JE's In charge and distribute all complaints/ detailing to his tradesmen, monitoring the work done and taking the complaint slip back from trademans on every working day, re-submit the same to JE's in charge after rectifying the complaint at complaint cell, failing which a recovery of Rs 1000/- per day shall immediately be effected from the contractor's dues in terms of conditions 25, 44 & 45 of IAFW-2249 (General Conditions of contracts). (ii) The complaint shall be attended & defect shall be rectified within 08 hrs i.e from 0900 hrs to 1700 hrs (excluding sunday & gazetted holiday), commencing from date and time of notifying the complaint slip failing which a penalty @ Rs.120/- per complaint per day (08 hrs) shall be levied upon/imposed on the contractor and necessary recovery shall be effected from his dues on this account. In case, after checking & attending the defects, if it is not possible to rectify the defect within 08 hrs, the fact shall be brought to the notice of Engr-in-Charge by the contractor/ his rep immediately and if Engineer-in-Charge is satisfied with the facts brought by the contractor, no recovery shall be made on this account. (iii) All T&P required for attending the complaints shall be provided by the contractor without any extra. (Iv) The above all aspect shall be deemed to be included in the quoted rate of the respective item.

Note:- Amount of credit of Rs. 30,555.00 for retrieved materials is mentioned in Schedule of Credit Page No. 121 to 123 of tender documents in pdf form which will be deducted offline while acceptance of tender.

Ashwani Kumar (BID ID -3116643)