SPL REPAIR OF BLDG NO P-204, P-205, P-206 AND P-207 AT CORPS ZONAL WKSP AREA JODHPUR AND BATHROOM AND TOILET OF BLDG NO P-63 AND P-64 OF PL ASC AND PROVN OF SECURITY FENCING AROUND NEAR BLDG NO P-964 OF HQ SQN BDE UNDER GE (A) NO.1 JODHPUR.

Amount

Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15cm thickness ( below or above ground level) of any description and removing rubbish to out side MD land complete all as specified and as directed.

Demolition of reinforced cement concrete (including cutting of reinforcement if any) in any description for roof, beams, columns, slabs, downward fascia, chajja, parapet wall & others and any position not otherwise specifically provided for and removing rubbish to out side MD land complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for 15 to 18 mm thick machine cut udaipur green stone slab (size as approved by GE), as in washbasin plateform, (table rubbed and polished) best quality as per sample, including & over 20 mm thick screeding in CM1:4 including rounding & double mouldlng with jointless finish of the edges, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.providing suitable dia hole in the slab for the gas pipe, complete all as specified and as directed.

M&L for 25 mm thick cement concrete 1:2:4, type B-0 (using 12.50 mm graded crushed stone aggregate), as in base course, to receive floor finishes, complete all as specified & directed.

M&L for glazed colour ceramic tiles (premium quality) of size 300X450X6-7 mm, as in vertical surface such as i.e. dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & including M&L 10mm thick backing coat in CM (1:3), (including Highlighter pattern), complete all as specified and directed.

M&L Machine cut kota stone slab 20 to 25mm thick(size not less than 580 mm X 580 mm), as in floor, treads of steps (single piece for steps) or similar works laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete over and including 20mm thick screed bed in CM 1:6, complete all as specified and as directed.

M&L Machine cut kota stone slab 20 to 25mm thick, as in riser of steps (single piece for steps), skirting, dado and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete over and including 10 mm thick backing coat in CM 1:4, complete all as specified and as directed.

M&L for joint free non skid ceramic coloured tiles (premium quality) of size 6 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm (size & shape, shade and pattern as approved by GE), as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including M&L 15mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed.

M&L for vitrified tiles of dark shade, 10mm thick (minimum) (square/ rectangular) polished area of each tiles equal to or not exceeding 0.36 Sqm (size & shape, shade and pattern as approved by GE), as in flooring, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour tiles over and including 15 mm thick skrid bed in CM 1:6, complete all as specified and as directed.

All as per Sl. Item No. 10.00 here-in-above, but as in dado/skirting over and including 10 mm thick skrid bed in CM 1:4

Taking down cement plaster any description on brick or stone walls, RCC surfaces, etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified and as directed.

M&L rendering 15mm thick in cement mortar 1:6 internal on stone masonry surfaces , finished even and smooth without using extra cement complete all as specified and as directed.

M&L rendering 10mm thick in cement mortar 1:4 on concrete surfaces of ceiling /chajja/facia, finished even and smooth without using extra cement, complete all as specified and directed.

Racking out joints/ pointing to squared rubble or polygonal rubble un-coursed or brought up to courses masonry built in cement mortar or cement lime mortar, coursed or un-coursed in walls not less than 12mm deep, washing the joints, removing rubbish off the premises and keeping the surface to pointed or plastered wet for two days prior to re-pointing or plastering complete all as specified & directed.

M&L keyed pointing in cement mortar (1:3) to squared rubble masonry regular coursed or un coursed complete all as specified & directed.

M&L Preparing new plastered or unplastered wall surfaces and applying with 1.5-2 mm thick wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over & including M&L one coat of primer on walls complete all as specified and as directed.

M&L for complete removal of existing treatment of any description on walls and applying with wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over & including M&L single coat of primer on walls complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete all as specified and as directed.

M&L for preparation of old decorated ceiling surfaces plastered or unplastered, by brooming down or steel wire brushing, scrapping down moulds, moss and efflorescent salts and trading oil & greasy spots, including cornices etc and applying two coat of white wash on ceiling, complete all as specified and directed.

M&L for complete removal of existing treatment of any description on walls and applying two coats of cement base paint over & including M&L single coat of white wash complete all as specified and as directed.

M&L Preparation of new plastered or un-plastered surfaces of walls and applying two coats of cement base paint over & including M&L single coat of white wash complete all as specified and as directed.

Taking down chowkhats or frame with shutters (without taking of shutters from the frames) area not exc 1.5 Sqm each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking of shutters from the frames) area exc 1.5 Sqm but not exceeding 4 Sqm each, complete all as directed.

S&F solid PVC Door Frame of size 50mm x47mm made out of 5mm wood grain printed PVC sheet incl all edges printed to match the shade reinforced with M.S. Sq tube, suppling & fixing in opening, complete all as specified & directed.

M & L Pressed steel frames of size 105X60mm of 1.25mm thick for doors with one or more rebates including necessary fixing lugs. hinges, lock strike plate,etc., complete all as specified and as directed.

M & L Pressed steel frames of size 165X60mm of 1.25mm thick for doors with one or more rebates including necessary fixing lugs. hinges, lock strike plate,etc., complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B-1 by using 20 mm graded stone aggregate as in bed block for fixing of hold fast complete all as specified and as directed.

Taking down steel windows and ventilators ( glazed / fly proof) of any description complete all as specified and as directed.

M&L factory made box type steel window side hung shutter, with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and as shown in Drg No CEJZ/TD/20 sheet1/3 to 3/3 complete with glazing bars & with or without cooler opening, dovetailed or welded and with one shop coat of zinc chromate primer (with or without cooler opening), complete all as specified and directed. Note:- (i)-:Both shutter (wherever applicable) will be jointed internally with flat iron of size 40 x 4mm and quoted rate deemed to include the cost component of the same. (ii)-Glass panes, guard bar & wire cloth shall be measured and paid seperately.

All as per item No. 30.00 here-in-above, but without glazing bar

S/F of Box type steel ventilator with top hung shutter including hinges with steel handle, and steel peg stay, complete with glazing bars, all as specified. Note:- (i)-:-Glass panes, guard bar & wire cloth shall be measured and paid seperately.

All as per item No. 32.00 here-in-above, but without glazing bar

M&L for mild steel work as in chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165, complete all as specified and as directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18 mm complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded wood grain printed PVC sheet PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wood grain printed PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) and jointed together with solvent cement complete all as specified & directed.

M&L factory Made flush shutters, 35 mm thick solid core with block board core construction and plywood face panels, one face is covered with decorative face veneer with lipping/frame to match and other commercial type, as per IS 2202(part-I, 1999) . The stiles & rails shall be with out any joint and made with non- coniferous timber hard wood (Hillock/ Mirantee/ Bosum/ Benteak) with moisture content not less than 12% as per IS. The face panel comprising of ply wood or cross band and face veneers shall be glued by hot pressed process. The over all finished thickness of face panel shall not be less than 40mm while the thickness face veneer shall not be less than 0.6 mm complete all as specified and directed.

M&L 35mm thick factory made 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a) complete all as specified and as directed.

S&F 100mm size butt hinges stainless steel, with stainless steel hinge pin, anodised type B-21 complete all as specified and as directed.

S&F 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed.

S&F 200mm long, mild steel, barrel tower bolts, stove enameled black with bright bolt complete all as specified and as directed.

S&F 150 mm long, mild steel, pressed handles, oval type, stove enameled black complete all as specified and as directed.

S&F 300mm long mild steel sliding door bolts plate type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

S&F for 150mm size aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

S&F 300 mm length aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

S&F 125mm size single action door spring hinge complete all as specified and directed.

S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-charge.

Hacking out old broken glass [any thickness, size, quality or description] from metal frames including punching or drilling out old glazing pins / spring clips complete all as specified and as directed.

S&F for sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

S&F of 4 mm thick pinheaded figured glass panes of size not. exceeding 0.5 Sqm fixed with oil putty complete all as specified and directed.

M&L preparation of steel surfaces of any description over 10cm width or girth not otherwise described and apply two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified & directed

M & L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over & including M&L single coat of pink primer complete all as specified and as directed.

Taking up or down 15mm bore steel tubing or CPVC and connections including cleaning for refixing or credited to contractor complete all as specified and directed.

All as per item No 53.00 here-in-above, but size of pipe 20/25 mm bore.

Supplying, laying, testing & commissioing of CPVC pipes 20 mm outer diameter SDR 11 & Plain or brass CPVC SDR 11 fittings, laid in trenches, complete all as specified and as directed.

All as per item No 55.00 here-in-above, but size of pipe 25 mm outer dia.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting, exceeding 10 cm but not exceeding 20 cm girth complete all as specified and as directed.

S&F in replacement bib cock with wall flange, chromium plated brass, fancy type 15mm dia complete all as specified and as directed.

S & F in repairs over head shower rose 125mm dia round shape single flow ,body and face plate CP brass, arm 300mm long jointing to pipe complete all as specified and as directed.

All as per item No. 58.00 here-in-above, but angular stop cock

S & F in repairs stop valves, 20 mm dia, cast copper alloy with capstan head, screwed down high pressure with crutch or butterfly handle with long shank and cup for iron pipe etc complete all as specified and as directed.

S & F in repairs pillar tap, cast copper alloy, chromium plated, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed.

S & F in repairs 75mm bore PVC nahani trap with CP mild steel grating (with or without hole) including jointing to waste pipe, fixed in cement concrete type B1, 1:2:4 complete all as specified and as directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D Type, 600 mm long between flanges including brackets complete all as specified and as directed.

S&F in replacement decorative type curtain rod stainless steel finish of pipe 22 to 25mm dia with best quality knob metal with double fitting type including stainless steel brackets fixed to walls complete with two nos decorative stainless steel knobs at each end, complete all as specified and as directed.

M&L 7.5 cm thick sand stone slabs in sunshades, chajjas, shelves, cills, landings cover stones templates etc n exc 2m in length punched dressed on face and along exposed edges self faced on other side and set and pointed in cement mortar 1:4, complete all as specified and as directed.

S & F in repairs vitreous china ware wash hand basin, Ivory (brand-I), flat back of size 450 mm X 300 mm including 32 mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe,PVC connection15mm size with PTMT nuts of length 600mm long, complete all as specified and as directed.

S&F in repairs vitreous ware wash down water closet [Pedestal Pattern], Ivory (brand-I), [ETWC] including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap connecting to drain pipe and flushing pipe etc., complete all as specified and as directed.

Dismantling of cast iron/PVC SWR pipes of 100/110mm bore, including fittings, jointed in cement mortar complete all as specified and as directed.

All as per item No. 70.00 here-in-above, but 75 mm bore pipe

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or floor of suitable size complete all as specified and as directed .

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or fixed to walls with MS clamps of suitable size complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps of suitable size complete all as specified and as directed .

S&F 110 mm bore (SWR) PVC bends any radius with access door complete all as specified and as directed.

S&F 75 mm bore (SWR) PVC bends any radius with access door complete all as specified and as directed.

S&F of PVC (SWR) 110mm bore vent cowl complete all as specified and as directed.

Supply only in repairs 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia and PVC connection 15mm size, 600 mm long with PTMT nuts complete all as specified and as directed. Note:- The colour of the cistern shall be as matching with the colour of the EWC/WC Pan

M&L 40mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floors & fixing of glass dividing strips & finishing the surface even & smooth with using extra cement complete all as specified & directed. Note:- Glass dividing strip shall be measured and paid seperately.

M&L 50 mm thick PCC (1:3:6) type C-1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight complete all as specified & directed

Complete removal of existing water proofing treatment of any description including bedding up to the true surface of original concrete, in RCC roof slab / stone patty and roughening the old surfaces by picking, sweeping clean and washing down with water to remove dust etc including removing rubbish to out side MD land and provide plastring 10 mm thick in CM (1:4) finished even & smooth over the RCC roof slab / stone patty for laying of water proofing treatment using water proofing compound (WPC) as per manufacturer instructionand including providing the following as roof treatment complete all as specified and as directed : - (a) FIRST COURSE: Applying a coat of bituminous primer @ 0.4 litre / Sqm manufactured by the same agency that of APP with a density 0.87 to 0.89 Kg/litre at 25 degree celsius on prepared plastred surfaces. (b) SECOND COURSE: Applying one coat of bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.20 Kg/Sqm (c) THIRD COURSE : Provide a layer of APP modified polymeric membrane centre core of 100mm micron HMHDPE, outer film 20 micron each, thickness 3.00mm having weight not less than 3.00 Kg/Sqm using butane torch with minimum 10cm side lap and 15cm end lap complete (d) FOURTH COURSE : Applying one coat of bonding material using blown type bitumen confirming to IS- 702 grade 85/25 @ 1.20 Kg/Sqm. (e) FIFTH COURSE : M&L 40mm thick PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate in roof padding , the surface of concrete is to be finished even and fair with out using extra cement NOTE :- WPC shall be measured and paid separately under respective

Supply only integral water proofing compound (ISI marked), complete all as specified and directed.

M&L 40mm thick plain cement concrete, 1:2:4 type B1 using 20mm graded stone aggregate mixed with water proofing compound, as in levelling courses of roof / chajja / kerbs, rounded or chamfered on edges including necessary form work complete all as specified and directed.

M&L for Rotational moulded polythene water storage tanks of 1000 ltrs capacity, white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I with PTMT ball valve heigh pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms including dismantling old tanks complete all as specified and as directed.

Demolition of stone / boulder masonry walling, built in cement mortar including all quoins, arches, pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and directed.

M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed.

M&L precast cement concrete block masonry using PCC 1:2:4, type B-1 solid blocks, 10 cm in width and setting in cement mortar 1:4, straight or curved on plan exceeding 6 m mean radius complete all as specified and directed.

M&L for 75 mm thick, PCC 1:4:8 type D2 by using 40mm graded crushed stone aggregate as in sub base of floor complete all as specified and as directed.

M&L precast cement concrete (1:2:4) type B-1using 20mm graded crushed stone aggregate as in kerb stone or mud steps, coping, rounded or chamfered on edge, fixing of holdfast etc complete all as specified & directed by Engineer-in-charge.

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any colour, design & pattern, & size/ shape, as approved by GE as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Taking down carefully cement conc /spalled out concrete from RCC roof projections, ceiling ,sunsheds, beams, etc upto cover depth by chipping out lightly including necessary scafolding etc, complete all as directed.

S&F in replacement TMT bars 12 mm dia fixed by way of stitching ( welding ot tieing with existing reinf) incl drilling holes etc & securing ends in walls etc ,complete all as specified and as directed.

M&L for cleaning the existing reinf of slabs , chajjas etc & applying a coat of SIKA RUSTOFF 11 to remove the loose rust particles etc & throughly cleaning the surface.,complete all as specified and as directed.

M&L for applying a coat of bond coat made with cement slurry (1 part cement to 1.5 -2 parts water) mixed with admixture LATEX POWER mixed @5 Kg per 50 kg of cement & applying to the conc surfaces @ 200 gm/sqm to obtain tack.,complete all as specified and as directed.

M&L for 15 -20 mm thick rendering in CM (1:1:2) using1 part of cement 1 part 2-3 mm screenings of stone agg & 2 parts coarse sand over the bond coat applied surfaces with cement mixed with SIKA PLASTOCRETE SUPER admixture @ 100 gm /50kg of cement & finishing the surface even & rough to receive final rendering coat. ,complete all as specified and as directed.

M&L for 5 mm thick rendering in CM 1:3 on ceiling & finishing the surface even & smooth w/o using extra cement, complete all as specified and as directed.

M&L for 10-15 mm thick rendering in CM 1:3 over the bond coat applied surfaces with cement mixed with SIKA PLASTOCRETE SUPER admixture @ 100 gm /50kg of cement & finishing the surface even & smooth, complete all as specified and as directed.

S&F GI chicken wire mesh of 0.71 mm dia wire & 12 mm mesh size fixed with nails & screws around RCC chajjas/fascias, wall, ceiling etc., complete all as specified and as directed.

M&L preparation of plastered surfaces of walls & writing letters or figures with (Block roman italic or Indian) exc 30cm high of suitable width as required at site with two coats of flourescent paint complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5m wide but not exceeding 1.5m in deep for foundation etc and not exceeding 1.50m deep for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in any type of soil complete all as specified and as directed.

S & F 150 mm bore reinforced cement concrete pipes, one end socketed, class NP2, laid in trenches and jointed complete all as specified and as directed .

M&L PCC 1:3:6 type C-2 (using 40 mm graded crused stone aggregate) as in bed to150 mm bore drain pipe including packing under and haunching against the side of pipe after they are laid and tested complete all as specified and as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed.

Removal of excavated material [Soil] to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Removing of existing filling in sunken floor of wc/bath/kitchen and repair to sunken floor with 15 mm thick plastering in CM 1:3 of internal surface with PC than painting with bitumen 30/40 over a coat of bitumen primer putting 50 micron polythene than filling with pcc 1:5:10 type E-1 using 40mm graded stone aggregate and inserting 50 mm bore GI water pipe light grade spout complete all as specified and directed.

S&F 150 mm floor door stopper of aluminium alloy body and tongue, anodised ,with hard drawn steel spring ,fixed in floor, complete all as specified and directed.

S&F rolled mild steel sections like angle, channel, flat, square etc as in framed work such as grills, gratings, etc, with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars barred iron doors; chowkhat, doors with MS sheet, ladders ;framed balusters walk ways railings framed work of water tanks and similar work confirming toFe-290Gde E-165 complete all as specified & directed

M &L in repair for fabrication of pressed steel cupboard shutters using 1.00 mm thick MS plain sheet & with frame 1.25 MM thick bent to shape incl two coats of syn enamel paint on int surfaces & two coats of hammer tone finish on external surfaces alongwith locking arrangement mortice lock handle etc complete. ( Taking down of existing Cupboard /Almirah included in the rates)

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including rough finished surfaces complete all as specified and directed.

Use and waste of form work to sides and soffits of lintels, beams, staircase railing, parapet wall, retaining wall, brackets, shelves and similar works for rough finished surfaces of concrete complete all as specified and as directed.

M&L reinforced cement concrete type B-1 [Nominal Mix] 1:2:4 using 20mm graded stone aggregate as in as in beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed.

M&L reinforced cement concrete type B-1 [Nominal Mix] 1:2:4 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use and waste formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide includingrough finished surfaces complete all as specified and directed.

M&L TMT steel bars of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

M&L for TMT steel bars of 6mm to 8mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

Exposing existing RCC members such as columns, slabs, lintels, beams, etc. up to the main reinforcement carefully by means of Chisel & hammer, hard wire brushes or any other mechanical means, so as to remove all loose concrete and cleaning the surface to remove all dust particles, etc. and make the surface ready for chemical treatment in bone dry condition.

M&L for 30 mm thick guniting in patches on to the required area on RCC columns, beams, stairs, lintels, retaining walls, sunshades, roofing slab etc. of all sizes and shapes at any heights from existing ground floor and at any locations with cement and mortar 1:2 (1 cement : 2 sand) under 2 to 2.8 Kg/Cm2 pressure after removing the damaged loose spalt concrete as specified here in before and applying one coat of rust convertor/kp-100 or its techhno commercial equivalent grade over reinforcement wherever necessary providing and tying in position 25mmx25mmx12 gauge dia wire MS welded mesh or smaller size over treated surface ready to receive grouts, curing for 10 days etc,loose spalt concrete portions by chipping, removal of dust over treated surface ready to receive grouts including 5mm to 10mm thick plastering in CM 1:4 to match existing surfaces and finished even and smooth including curing for 10 days etc, complete operation all as directed removing the debris out side the MOD land in low lying areas and leveling as directed, complete all as directed by Engr-in-charge. Note (i) After placing the additional reinforcement all concrete surfaces shall be thoroughly scrubbed with brushes, washed with water and alloy to dry. To this surface apply chemistic polycrete admixture at the rate not less than 2% by weight of cement or as per manufacture’s instructions. (ii) When polymix coating is in tackey condition guniting is done with polycrete admixture at the rate not less than 2% by weight of cement or as per manufacturer’s instruction. Polycrete admixture shall be procured from Chemical Adhesive Pvt Ltd Co or their authorized dealer. (iii) Cost of the above aspects shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account. (iv) Work shall be carried out up to first floor

M&L for fabrication of powder coated (powder coating min thickness 50 micron) aluminium frame work as in frames for aluminium windows with or without rebate or for sliding windows(two track/three track ), ventilators etc with louvers having suitable mechanism for tilting , U shaped fillets for securing Jallies etc & the likes complete all as per sample kept in GE Office & fixed in position complete all as specified and directed. Note : Glass panes, in louvers, GRILL & stainless steel wire cloth shall be measured & paid for seperately.

M&L for fabrication of powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. Note : Glass panes, in louvers, GRILL & stainless steel wire cloth shall be measured & paid for seperately.

Pre powder coated aluminium decogrill all as per sample fixed to aluminium framework of windows & ventilators, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S & F rolled mild steel sections of grade Fe - 410 - S as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.complete all as specified and as directed.

M&L for Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws, including dismantling old existing roof covering sheet of any description, complete all as specified and as directed.

M&L for Prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in ridge, eaves valley gutters, hip etc., fixed with self tapping screws all as specified and as directed.

Aluminium snap grid frame work of 600 X 600 mm panel size for false ceiling with Aluminium "T" section of size 38 X 25 X 1.50 mm thick for main runners, 25 X 25 X 1.5 mm thick for cross runners and angle of size 25 X 25 X 1.50 mm thick along the walls suspended with and including 6mm dia, Galvanized mild steel wire as in suspenders of ceiling members fixed in proper position, including fixing of Exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm grids of size 600 X 600 X 6mm thick confirming to IS and fixed with aluminum staples on snap grid as per manufacturer's specifications and including applying two coats of synthetic enamel paint over a coat of primer complete all as specified and as directed.

GI frame work size of grid 605 x 605mm for seamless ceiling comprising of GI perimeter chanel 0.55mm thick with two unequal flanges of 20 & 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm c/c intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm c/c with GI cleat and steel expansion fasteners with and inccluding ceiling section (not exceeding 1.2M length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to intermediate channel at 457mm c/c and hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and including providing gypsum board 12mm thick in ceiling fixed with screws as per manufacturers instructions over the frame work and preparation of ceiling board and applying two coats of oil bound distemper over a coat of 'Birla' wall / ceiling care putty including dismantling of existing false ceiling of any thickness with cover fillets complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of wall and applying three coats of white wash on wall surfaces complete all as specified and as directed.

S&F solid PVC Door Frame of size 50mm x47mm made out of 5mm plain PVC sheet incl all edges printed to match the shade reinforced with M.S. Sq tube, suppling & fixing in opening, complete all as specified & directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded wood grain printed PVC sheet PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wood grain printed PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) and jointed together with solvent cement complete all as specified & directed.

S&F 100mm size butt hinges extruded aluminium alloy, with mild steel hinge pin, anodised type B-21 complete all as specified and as directed.

S & F in repairs white vitreous china squatting pan "Orissa pattern" of size 580 mm X 440 mm with integral foot rests and PVC 'P' or 'S' trap including provision of cement concrete bedding 1:5:10 type E2 complete all as specified and as directed.

S & F in repairs vitreous china ware wash hand basin, Ivory (brand-I), flat back of size 550 mm X 450 mm including 32 mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe,PVC connection15mm size with PTMT nuts of length 600mm long, complete all as specified and as directed.

M&L for Granite slab 18 to 20mm thick machine cut, factory polished, Jet Black colour, as in WHB plateform and cooking plateform bedded and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the shade of granite stone over and including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4, complete all as specified and directed.

S & F vitreous china urinal, half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar [1:2], securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, including 32mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, 32mm bore PVC flexible waste pipe, grating and union for discharge pipe, PVC connection15mm size with PTMT nuts of length 600mm long, Urinal spCP screws, etc complete all as specified and as directed.

S&F in repair, stop valve, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15mm bore iron pipe or for union complete all as specified and as directed.

S&F in replacement two way angle cock with wall flange, chromium plated brass, fancy type 15mm dia complete all as specified and as directed.

S&F in replacement GI tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking down old tubing complete all as specified and as directed.

Excavating in post holes or similar holes each not n exc 0.50 cu.m,getting out any type of soil,returning,fillig in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm complete all as specified and as directed.

M&L plain cement concrete 1:4:8 type D-2 by using 40mm graded crushed stone aggregate as in foundation filling and mass concrete,complete all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C-2 by using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete for fencing post complete all as specified and as directed .

M&L precast cement concrete block masonry using PCC 1:2:4, type B-1 solid blocks, exceeding 10 cm in width and setting in cement mortar 1:4, straight or curved on plan exceeding 6 m mean radius complete all as specified and directed.

M&L 15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces mixed with water proofing compound as per manufacturer instructions and finished the surfaces even and smooth with out using extra cement complete all as specified and as directed. Note :- WPC will be measured and paid seperately.

M&L for mild steel work confirming to Fe-290 [Grade-E-165] for post and struts in fencing including cutting tops to shape as directed, bending to shape, notching for wire, etc flat iron fillets for securing wire mesh etc, necessary drilling holes for securing barbed wire etc including bolting or riveting etc as required complete all as specified and directed.

M&L for rolled mild steel confirming Fe-290 (Gde E-165) in door or gates of angle (35x35x5 mm) or other section with gusset plate, rail braces etc complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (inclding of steel, sheeting or other covering ) and hanging also fastening and fixing complete all as specified and as directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n. exc 10cm long and dia 5 to 10 mm complete all as specified and as directed.

Supply only chain link fencing with 3.15mm dia of 50mm x 50mm mesh size MS galvanised fencing, complete all as specified and as directed.

Fixing only chain link fencing including line wires,any mesh,size and type of standards,rails, straining bolts, etc including provision of binding wire complete all as specified and as directed.

Supply only Mild steel round or square bars,in available length Fe-290(Gde-165) for fixing of chain link fencing complete all as specified and as directed.

S&F galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as specified and as directed. Note : - Each line wire to be measured.

Supply and Fixing of concertina coil as 600mm dia rounded 50 circuls covering in 10RM with necessary fixing material complete all as specified and directed.

Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed.

Taking down carefully UNSV main switch and DB's including MCBs of any size make, type and capacity and depositing at site as directed.

Taking down carefully UNSV submain wiring of any size and all as directed.

M & L for (concealed) point wiring complete with multistranded copper conductor 1.5 Sqmm PVC insulated unsheathed single core FRLSH cable 1100 volt grade, confirming IS 694 & colour code in conduit system of wiring, drawn through in and including non-metalic PVC concealed (including Cutting Chases and make good the distrubed surfaces ) conduit of size 20 mm or med grade as required as site, totally concealed in walls / and surface on floors / ceiling or fixed on surface of walls / columns / beam / tie beam etc by means of saddles and clips etc incl all conduit accessories / fittings / junction boxes / inspection covers etc of heavy grade, ISI marked and sunk terminal boxes of CI or 16 SWG pressed steel housing, totally concealed in walls with 3mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws and sunk / cup washers, for mounting of switches, sockets fan regulators etc incl 1.5 Sqmm FRLSH PVC insulated, unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, all as specified, directed and shown on drgs for The rates of chase cutting on wall done concealed conduit and steel terminal boxes & Making good disturbed surface are included in the unit rates, suitable for One light / fan point controlled by one, one way switch all as specified and directed by Engr-in-Charge.

All as per serial Item No. 154.00 above but for one 3 pin socket outlet 5/6 Amps on the independent board, complete all as specified and directed.

All as per serial Item No. 154.00 above but for one 3 pin socket outlet 5/6 Amps on the same board, complete all as specified and directed.

All as per serial Item No.154.00 above but with 4.00 Sq mm single core multistanded copper conductor cable for 3 pin 16 Amp socket outlet on independent board .omplete all as specified and directed .

S&F Switch piano type, single pole, one way, 6 amps, 230 volts, complete all as specified and directed.

S&F Socket, two-in-one, 5 pin, 5 Amp, universal type, 230 volts, shutter provide complete all as specified and directed.

S&F Switch piano type, single pole, one way, 16 amps, 230 volts, complete all as specified and directed. Make: Anchor/Havells/Cona

S&F Socket, 6 pin, 6/16 Amp, multipurpose shutter type, shutter provided 230 volts, complete all as specified and directed.

S&F Lamp holder, metal cased, bakelite body, 230 volts, complete all as specified and directed.

S&F LED lamp 9W complete all as specified and directed by the Engineer-in-Charge.

S&F Ceiling rose, two to three terminals, bakelite body, 230 volts, complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including AC decorative box type with driver, holder including,copper conductor cable of suitable size from ceiling rose complete complete, 4 ft long all as specified and directed.

S&F bldg security LED Light Luminaire of 35 Watts having IP 65 protection fiting made out of pressure die cast Aluminium housing, operating Voltage 140-270 Volts with in built surge protectore, toughened glass with and including GI pipe 40 mm bracket of 1.5 m in length including drilling holes, nuts & bolts 2 coats of red oxide primer on GI pipe and fixing with wall security light on building wall connecting cable complete all as directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

S&F MCB, B Curve type, 10 kA, 63Amp, 240 volts, SPN with over load and short circuit protection, complete all as directed.

S&F MCB, B Curve type, 10 kA, 32Amp, 240 volts, SPN with over load and short circuit protection, complete all as directed.

S&F MCB, B Curve type, 10 kA, 6 to 32 Amp, 240 volts, Single Pole with over load and short circuit protection, complete all as directed.

Supply and fixing as MCB DB TPN (double door) 8 Ways, 415 Volts including 200 Amps rated bus bar neutral link, IP-43 Protection, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall incl dismantling of old UNSV DB all as specified and directed by the Engr-in-Charge.

Supply and fixing as MCB DB SPN (double door) 8 Ways, 240 Volts including 200 Amps rated bus bar neutral link, IP-43 Protection, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall incl dismantling of old UNSV DB all as specified and directed by the Engr-in-Charge.

S&F in replacement exhaust fan, heavy duty steel body, AC single phase 300 mm sweep, 900 RPM, complete with frame & louvers, connecting with & including 3 core PVC insulated copper conductor flexible cable of size 23/0.0076 (or eq. Size in mm) from ceiling rose to fan, complete all as specified and as directed.

S & F in replacement ceiling fan 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE 5 star rating, brushless direct current motor (BLDC), suitable for single Phase 230 volts and connected with twin core twisted flexible copper conductor cable from ceiling rose to fitting complete all as specified and as directed. .

Supply, fixing, testing and commissioning miniature circuit breaker (MCB) TPN/FP 40 to 100 AMP, 415V 10KA 'C' curve and current carrying capacity in the DB complete with connection, complete all as specified and directed.

S&F single pole and neutral enclosure with two pin and earth plug socket complete with one single pole MCB 32 Amp ‘C’ curve type, 230 volts, 10 KA, complete all as specified and directed.

M&L for sub main wiring with 2 run of 6 Sqmm FRLSH, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLSH, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non metallic PVC conduit 15 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note:- Two run of 6 Sq.mm. and one run of 6 Sq.mm (earth wire) cable incuding one run of conduit pipe will be measured as one length including making good the disturbed surfaces

Earthing complete with galvanised steel earth plate electrode 60 x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in elevtrical plate no. 3 connected to Earthing test point all as specified or indicated including testing on completion Note : (i) Rates are deemed to be included for necessry earth work ,PCC pit , RCC cover etc complete. (ii) Earth lead shall be up to 7.5 Mtr and rates are deemed to be included for GI pipe 15mm Light grade upto 7.5 mtrs for protection of earth wire 4.0 mm dia, complete all as specified and as directed.

Supply, laying, jointing, testing and commissioning 1100 volt grade heavy duty XLPE insulated LT under ground cable, sheathed, as per IS- 7098 (Part I) 1988, galvanized steel strip armoured heavy duty multi stranded aluminum conductor laid in trenches / passed through pipe/duct road crossing, fixed on poles/ wall with clamps made out of mild steel flat iron including fixing accessories like brass cable glands double compression type, lugs, nuts, bolts, washers etc of size 3.5 core 25 sqmm, complete all as specified and directed Note: - (i) Excavation and earthwork, sand cushioning, PCC cable cover, shall be measured and paid separately in relevant item here in after .

All as per serial Item No. 179.00 above but for 2 Core 16 Sqmm cable

Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1, flat, size 300x180mm x40 mm, complete all as specified and as directed.

M&L for dry clean fine river sand as in sand cushioning to underground cable including punning down of sand layer, complete all as specified and as directed. Note :- Punned thickness shall only be measured and paid.

M&L for galvanised steel tubing, medium grade, for protection of cable, laid in trenches/road crossing/floor or fixed to pole/wall with all fittings, of size 40 mm bore, complete all as specified and as directed.

NOTE:- (a)- Quantities are clubbed in BOQ for different Jobs. Details as per Annexure-I on Sl. Page No. 39 to 42 of tender document. (b)- The contract sum shall be arrived at after duducting amount of schedule of "Credit" from the Total quoted amount

SN TECHNO CONSTRUCTIONS

JB INFRA

Harsh Enterprises

M/S SUMAN ENTERPRISES