Construction of Special Repair of Govt. College for Women at Gohana in Sonepat Distt. (Re-invited)

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing In cement (HSR 8.5 b)

First class brick work laid in cement sand mortar 1:4 in foundation and plinth (HSR 11.4)

10 mm thick cement plaster 1:3 (HSR 15.2)

12 mm thick cement plaster 1:4 (HSR 15.5)

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall (HSR 15.10)

Scraping of cement plaster (HSR 8.32 c)

Providing and fixing hard drawn steel wire fabric 75 mm X 25 mm rectangular mesh with 3.25 mm dia wire fixed on steel windows of standard rolled sections with 3 mm thick flat iron cover moulding of 12.5 mm width fixed with machine screws welded complete in all respect (HSR 18.33)

Providing and laying 150mm thick granular sub base consisting of drainage-cum-filter layer confirming to Table 400.1 Grading - VI of MoRT&H 5th edition, mixing in a mechanical mix plant at OMC, carriage of mix material to the site of work, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory power roller to achieve desired density complete as per clause No. 401 of MoRT&H specifications. Note: - 1.Only crushed metal material should be used. No local earth sand shall be used. The material finer than 425 micron shall have zero Plasticity Index (PI). 2. Materials to be used and operations of manufacturing shall be approved by engineer.

Providing and laying 80mm thick interlocking paver blocks ISI marked (IS code: 15658:2006) of all shapes and colours in design mix cement M-40 as per IRC:SP:63-2004, over a bed of 30 mm thick fine sand complete in all respects. [HSR 10.159]

Providing & fixing false ceiling with grooves with 12mm to 15mm thick, 600mm x 600mm best quality mineral fibre tiles of approved make fixed on M.S. Steel runners frame i/c cost of screws angles, cleats, rawel plugs, with taping and painting etc. complete in all respect as approved by the Engineer-in-Charge (HSR 13.93)

Providing & laying average 6mm thick POP coating on walls, ceiling, beams and lintels etc. complete in all respects as approved by the Engineer-in-Charge (HSR 13.94)

Painting one coat with exterior acrylalic paint on old work (1st quality apex) (HSR 16.82)

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work (HSR 16.60)

Painting one coat with synthetic enamel Paint in all shades on old wood-work, or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint (HSR 16.7)

Providing & applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete (J.K. / Birla make) (HSR 16.81)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces (HSR 16.25)

Scarping white was and colour wash (HSR 8.32a)

Factory-manufactured wire gauze door and windows shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash, etc, (non coniferous timber other teak, conforming to I.S. specification no. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide locak rail 200 mm wide bottom rail and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fitting other than specified above, but including labour for fixing the same in position)- (styles and rails of windows shutter shall be 75 mm wide) (HSR 17.92) (i) 30mm thick.

Cost of aluminium fitting cokmplte for doors and windows, such as tower bolts, handles, etc., and screws for these fittings (excluding sliding bolt)- (a) for single lead shutter (HSR 17.72a)

Providing and fixing aluminium work for doors windows, ventilators and parti-tions with extruded built up standard tubular sections appropriate Z sections and other sections of approved make conforming to IS, 733 and IS:1285 fixed with rawlplugs and screws or with fixing clips or with expansion hold fasterners including necessary filling up of gaps at junctions, at top, bottom and sides with required neoprene felt etc. aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat angle. Aluminium snap beading for glazing / panelling C.P. brass / stainless steel screws, all complete (HSR 17.95)

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12)

Providing & fixing PVC flushing Cistern low level conforming to IS 7231 of reputated make such as hindware, CERA or equlant / ISI marked as approved by the Engineer-in-Charge complete with flush pipe with bend and all other necessary miscellaneous fitting required to complete the job to the entire satisfaction of the Engineer-in-Charge (HSR 30.124)

Providing & fixing in position of best indian make (To approval of the Engineer-n-Charge) Chinaware Indian type water closet suit PVC cistern with dual button of 10 Ltr. Capacity of repuated make such as hindware CERA or equilant / ISI marked P/S trap & other necessary fitting required to complete the job to the entire satisfaction of the Engineer-in-Charge (HSR 30.125)

Providing and fixing in position 15 mm i/d C.P brass bib Cocks of best quality (as required by Engineer-in-charge) (a) Bib cock long body (HSR 30.75a)

Providing & fixing in position best Indian Make flexible tube connection (iii) CP Brass 15mm x 450mm (HSR 30.82 b)

PROVIDING AND FIXING IN POSITION INDIAN MAKE (ORDINARY) LAVATORY SUITES Consisting of Lavatory in VITREOUS CHINAWARE size as given Below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary R.S or C.I BRACKETS for building into wall including Painting 32 mm C.P BRASS WASTER WITH C.P brass chain and rubber plug 15 mm C.P BRASS SCREW DOWN PILLAR TAP WITH Jamnuts or couplings best design ( as approved by the Engineer- In-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS FLOORS AND PAINTING OF FITTINGS ETC. (HSR 30.41) (V) Size 560mm x 450mm with one no. tap.

Pdg. & fixing PVC rain water Pipe 6 kg Presure of ISI Mark in Cement morter during masonary work (a) 100mm dia PVC pipe 6 Kg. presure (HSR 13.89a)

Providing & fixing PVC bend ISI mark (a) 100mm dia PVC ben (HSR 13.90 a)

Supplying and fixing hydraulic door Closer, I.S.I mark, with necessary Screws, etc., complete ( C) ISI designation No. III (Size of door 851mm to 1000mm) (HSR 17.82 c)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRRON Mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall or chromium plated brass clamps with C.P brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.71 a i) Indian make 600mm x 450mm

Bijender Singh