WBIW/EE/MDD/e-NIT-15(e)/ 2025-26/S2

Supplying Jhaw / Eucalyptus bullah piles at work site, including dressing and making one end pointed. Note : Diameter of pile to be measured at a distance of 1.5m from the thicker end. i) 20 cm. average dia.

ii) 15 cm. average dia.

Labour for driving Jhaw / Eucalyptus bullah piles by monkey in all sorts of soil including hoisting and placing piles in position, protecting the pile head with iron ring and cutting and shaping heads before and after driving and including hire and labour for necessary driving appliances and all tackles. i) 20 cm. average dia.

ii) 15 cm. average dia.

Supplying, fitting and fixing with iron nails half split bullah wailing pieces and cross pieces etc. complete with cost of all materials and carriage to site. Width of thinner end above 10 cm. and less than 15 cm. Jhaw / Eucalyptus.

Splicing (as per drawing and direction of the Engineer-in-charge) in position 150 mm. to 250 mm. dia. of individual bullah with 2 Nos. 1250 mm.x 75 mm. x 10 mm. M.S. flat and 4 Nos. half rings made of (700x75x6) mm. M.S. flat fitted and fixed with 4 Nos. 12mm. dia. bolts with nuts and washers. Flat bars are to be fitted and fixed with 3 Nos . 20 mm. dia. through bolts with nuts and washers including cost of supply and carriage of all materials, making necessary scaffolding, stagging etc. drilling holes complete (splicing is to be done on position after the bottom bullah is driven as per necessity). Length of lap of bullah should be provided as five times the diameter of bullah or 90 cm. whichever is greater.

Labour for taking out old wood work including cutting bolts and nuts and stacking within a lead of 100 M etc complete as per direction of Engineer - in - charge (the quantum should be corrected upto 3 decimel.)

Best Seasoned wood work in shutters, posts, plates, rafters, battens, trusses, beams, purlins, bargas, wheel-guards, running boards, frames etc. including supplying at site, handling, hoisting, fitting & fixing in position excluding the cost of bolt and nuts only but including the cost of nails and screws with cost and carriage of all materials complete as per the direction of the Engineer-in-charge. (The quantum should be corrected upto 3 decimels). Hard Wood (Mahua / Arjun / Tentul etc or similar quality hard wood as approved by the Engineer-in-charge.

Supplying at site and fitting & fixing Mild Steel long nuts & bolts etc. complete as per the direction of the Engineer-in-charge.

Coal tarring with 5% pitch including cost of material and labour complete as per direction of the Engineer-in-charge. Two Coat

Supplying, dressing and stacking at site bamboo pins above 5 c.m. diameter. and upto 7.5 cm. diameter. (dia. to be measured at mid length).

Driving bamboo pins in standing or flowing water including scaffolding and driving appliances. Where boats are not necessary.

Supplying, fitting, fixing with iron nails half split bamboo wailing pieces (av. dia. of bamboo not less than 50 mm.)

Supplying to site empty cement polythene bags (capacity 50kg) in good condition including stacking, incedental charges etc. all complete (capacity 50 kg).

Labour charges for filling empty cement gunny bag / polythene bag (capacity 50 kg) with all kinds of earth (wet or dry), sand or agreegates(stone / brick) and sewing as done in case of cement bags ,( tying with a knot after filling will not be accepted ) , and stacking within a lead of 30 metre as per direction of Engr-in-charge (cost is excluding the cost of any types of filling materials). NB:- Volume of earth/ sand filled bags should not be less than 0.028 cum/ bag.

Dumping in position earth / sand filled gunny / poly bags (capacity 50 kg) within a lead of 30 metre inclusive of all lifts.

Earthwork from borrow pits over existing embankment or for repairs to embankment, closing breaches etc. within an initial lead of 30 metre and lift of 1.50 metre including breaking clods and depositing the same in layers not exceeding 25 cm. and rough dressing etc. complete as per profile.

Please Enable Macros to View BoQ information