Supply, erection, testing & commissioning for LILO of S/C 132kV Dhandhuka –Paliyad Line & S/C 132kv Dhandhuka –Botad Line at 132K Ranpur on M/C Tower with ACSR Panther Conductor 48F OPGW cable having route 1.7RKM (Overhead part)

Sr. No. Description of Works - SAC Code 9954 Amount in Rs.

PART -A Supply of Materials

PART -B, SCHEDULE -

Erection of Line

PART -B, SCHEDULE -

Old line dismentalling

TOTAL F.O.R. COST WITHOUT GST

Service of "Works Contracts" GST @ 18% (SAC 9954)

TOTAL END COST WITH GST

I am / we are willing to carry out this service package of works contract stated above at GST 18% (in figure)

______ % (in words _____ %) below / above the estimated TOTAL END COST for all the items stated there

The amount of tender works out with above % (in figure) for TOTAL END COST Rs. _____________ (in

I / we confirm that our above quoted rates are ON firm price basis; except Percentage Basis on FIRM

PRICE with Price Variation applicable on (i) Supply of Tower Materials (Including Bolts-Nuts) and (ii)

Hardware & Accessories of ACSR Panther for which Price variation will be applicable.

1) Separation of the Contract into Supply of Goods, Services and Civil Work, is only for convenience and

better economical management and for the ease of Accountancy but the entire Contract, is to be assessed

under GST Law, as the Works Contract Service, which is, as per the provisions of Section 2(30), read with,

Section 2(119), further read with, Paragraph 6(a) of the Schedule II to the CGST Act, 2017 or SGST Act,

2017 and similar provisions, applicable under the UTGST Act, 2017and the IGST Act, 2017 and the entire

activity, would be subjected to levy of Tax, at the rate of 9% CGST + 9% SGST or 18% IGST, under the GST

Law. However, Classification Codes for different segments or portions of the Works Contract, may be

specified separately, in the Supplies, with a final common Classification Code of Works Contract Service.

2) The Bidder is hereby conveyed that only SAC Code and Tax rate for supply of Service Works Contract

i.e. 18% is relavant for the purpose of contract since the contract is works contract and any separation in the

works is for better management and convenience purpose.

It is to state that bidders are however requested to fill the HSN code item by item for the knowledge and

transparency purpose which shall have no bearing on price or taxation payment.

Signature of Authorized Representative of Company / Agency

SEAL & SIGNATURE Status _________________

OF BIDDER Name of bidder Company

Estimated Cost - SUPPLY

Supply, erection, testing & commissioning for LILO of S/C 132kV Dhandhuka –Paliyad Line & S/C 132kv Dhandhuka –Botad Line at 132K Ranpur on M/C

Tower with ACSR Panther Conductor 48F OPGW cable having route 1.7RKM (Overhead part).

Tender No. ACE(P&C)/Contract/E-457/TL/132kV/S&E

Description of Supply with Detail HSN / SAC Unit Freight, Unit FOR Unit FOR Total Cost

Sr. code for Packing & Insurance

Specification of Service Package - Works identification

Unit Quantity Unit Rate Forwarding Charges in

Rate (Excl. GST)

Contract (SAC Code 9954) only charges Rs. in Rs. in Rs.

A Supply of Materials

A.1 Tower Materials

A-2 ACSR Panther conductor kM 0 234904.00 2867.00 1229.00 239000.00

A.3 Silicone Rubber insulators - 132kV

A.3.3 132kV,90kN - Suspension SRI Nos. 19 2250.00 42.00 18.00 2310.00

A.4 Insulator hardware for ACSR Panther

A.4.1 Single suspension Nos. 18 1564.00 17.00 7.00 1588.00

A.4.2 Double suspension Nos. 0 4413.00 34.00 15.00 4462.00

A.4.4 Double tension Nos. 72 4945.00 51.00 22.00 5018.00

A.4.6 Mid span joint Nos. 17 695.00 6.00 3.00 704.00

A.4.7 Vibration damper Nos. 384 572.00 11.00 5.00 588.00

A.4.8 Repair sleeve Nos. 2 252.00 6.00 3.00 261.00

A.5 Hardware for Earth wire (7/3.15mm)

A.4.1 Suspension Clamp Nos. 0 440.00 12.00 5.00 457.00

A.4.2 Tension Clamp Nos. 0 433.00 9.00 4.00 446.00

A.4.3 Mid span Joint Nos. 0 115.00 1.00 1.00 117.00

A.4.4 Cross by clip Nos. 0 213.00 4.00 2.00 219.00

A.4.5 copper earth bond Nos. 0 558.00 13.00 6.00 577.00

A.6 OPGW - 24 Fibre (220kV)

A.6.1 24 Fibre (DWSM) OPGW fibre Optic cable Km 0 145356.00 1999.00 857.00 148212.00

A.6.2 Installation Hardware set * & accessories for Km 0 45351.00 502.00 215.00 46068.00

above OPGW i.e. all cable fittings & accessories

like suspension clamps, tension clamps, vibration

dampers, earthing clamps, down lead clamps, in-

line splice enclosures etc. including; Pigtails FC-

a) Fibre Optic Approach Cable -

400 Mtrs - For 220KV S/S &

500 Mtrs - For 400KV S/S

(with installation hardware like ties/ clips / cleats,

conduits, ducts, supports, fittings, accessories

(Any variation in quantities shall be absorbed by

A.7 OPGW - 48 Fibre (220kV)

A.7.1 48 Fibre (DWSM) OPGW fibre Optic cable Km 1.7 195533.00 2385.00 1022.00 198940.00

A.7.2 Installation Hardware set * & accessories for Km 1.7 48279.00 644.00 276.00 49199.00

above OPGW i.e. all cable fittings & accessories

like suspension clamps, tension clamps, vibration

dampers, earthing clamps, down lead clamps, in-

line splice enclosures etc. including; Pigtails FC-

a) Fibre Optic Approach Cable -

400 Mtrs - For 220KV S/S &

500 Mtrs - For 400KV S/S

(with installation hardware like ties/ clips / cleats,

conduits, ducts, supports, fittings, accessories

(Any variation in quantities shall be absorbed by

TOTAL COST FOR MATERIALS

Service of "Works Contracts" GST @ 18% (SAC 9954)

ERECTION PORTION

PART B SCHEDULE -

Supply, erection, testing & commissioning for LILO of S/C 132kV Dhandhuka –Paliyad Line & S/C 132kv Dhandhuka –Botad Line at 132K Ranpur on

M/C Tower with ACSR Panther Conductor 48F OPGW cable having route 1.7RKM (Overhead part).

Tender No. ACE(P&C)/Contract/E-457/TL/132kV/S&E

HSN / SAC FOR Total Cost

Description of Supply with Detail Specification of Service Package - Works code for

SN identification

Unit Quantity Unit Rate (Excl. GST)

Contract (SAC Code 9954)

B ERECTION OF LINE

B-1 Schedule-1 (Tower line)

The work of detail survey, preparation and submission of profiles in 6 copies

(PLSCAD as well as hardcopy),

Detail scope of Work :-

(a) Fixing of tower as per actual requirement, site condition and plotting of line on

profile having standard details i.e. span length, lat-long (co-ordinate), chainage,

weight and wind span, all dimensions, scale, legends, tower spotting data etc. as per

requirement and along with all require details.

(c) Preparation and submission of tower schedule as per standard require details

with all the Major - Minor crossing details in profile drawing and tower schedule,

along with due care of clearance as per prevailing standards i.e., for all electric line

1 with pole, all type of track, river, pond, nala, road, canal etc. kM 1.700 10222

(d) Details of Right of Way in profile drawing. i.e. Building, Temple, Well etc.

(g) Plotting line on TIKKA-MAP (Revenue Land map) - Required TIKKA-MAP will be

provided by GETCO.

Importantly, any work other than mentioned will align with the specific requirements

outlined by the Engineer-in-Charge.

Note : The survey report will be submit with sign and stamp of the surveyor agency

and engineer in charge.

Check Survey along with plotting of line route on village (tika) map with Coordinates

2 including detailed survey, preparation of profiles and revision in original route kM 1.700 9277

alignment, if any and as per instruction of EIC.

Excavation excluding back filling, but including shoring, shuttering, dewatering, tree

cutting for tower footings etc. for:-

a) Normal soil either dry or wet / Sandy soil. CMT 115.67 307.00

b) Black Cotton Soil either dry or wet. CMT 2643.50 614.00

c) Normal submerged / marine soil where dewatering is necessary. CMT 0.00 484.00

d) Black cotton submerged / marine soil where dewatering is necessary. CMT 1351.83 703.00

e) Soft Rock CMT 0.00 1066.00

f) Hard Rock CMT 0.00 2212.00

Installation of steel reinforcement in concrete foundation including supply of

GETCO Approved M.S. bars, binding wire. Work also includes their cutting, bending,

4 shaping and binding with binding wire and fixing in position of TMT bars as per MT 38.42 99900.00

drawing before the concrete work and as per instruction of the EIC

Stub-setting with prop or template including back-filling, during back filling dispose

of excess soil and levelling of site is to be done as per instructions of EIC but

excluding excavation and concreting etc. for all types of towers/extensions except

special towers. (Weight of stub, cleat & template with Bolt & Nuts of stub & template

shall be counted)) up to 6 mtr extension. (SOR Part-A -6)

6 ---- Do ---- up to 9 to 25 mtr extension MT 12.02 9918.00

Concreting of foundation by M20/M15/M30 mixture including shoring, shuttering,

compaction, dewatering etc. for normal tower / tower with extension upto 25mtr.

After completion of concrete work, curring (watering to concerte) is to be done as

7 per instruction of EIC.

(Rates are inclusive of supply of GETCO approved Cement only.)

Grounding of towers with pipe type earthing including excavation and back

filling, with supply of all materials like 32mm dia heavy duty 3 mtr. long G.I. Pipe,

x 6 mm G.I. flat, GI bolt-nuts, with GI spring washer, salt, charcoal etc. as per

drawing and as per instruction of EIC.

Grounding of towers with COUNTER POISE TYPE including excavation and back-

9 filling and supply of all materials like GSS wire, lugs, bolt-nuts, salt, coke/charcoal as Set. 0.00 15756.00

Erection of super structure upto 6 meter extension including tree cutting, fixing of

tower accessories, attachments except ACD /DP /NP /CIP /PP and excluding tack

welding of bolts as per instruction of EIC. This includes taking delivery of tower

10 materials and bolt-nuts from GETCO’s stores etc. for normal, extension & special MT 153.75 10076.00

towers at destination and keeping them in safe custody and transporting the same to

Same as above but erection of 9/12/15/18/21/25 mtr. Extention with Tower.

Fixing of Anti-climbing devices including supply of barbed wire as per drawing

and as per instruction of EIC.

Fixing of DP / NP / PP / CIP including supply of plates and supply of G.I. bolts-nuts &

12 tack welding as per drawings and as per instruction of EIC. Loc. 0.00 1690.00

(II) For D/C Loc. 4.00 3379.00

(II) For M/C Loc. 6.00 6758.00

HSN / SAC FOR Total Cost

Description of Supply with Detail Specification of Service Package - Works code for

SN identification

Unit Quantity Unit Rate (Excl. GST)

Contract (SAC Code 9954)

Tack welding of nuts upto approx. 10 mtrs. height OR two bottom-most panel from

ground level at three places on the nuts diametrically and applying zinc rich paint Per

13 immediately after tack welding and as per instruction of EIC. 48000 15.00

Work of Painting of Line name, Location No., two coat Painting Color code of

desired length and telephone no. on Tower Leg with letter of Gujarati language using

14 ISI marked Paint as per instruction of EIC including Supply of paints and other

require materials.

All four legs - For 4 Nos. of Line (M/C) per loc 6.00 862.00

All four legs - For 2 Nos. of Line (D/C) per loc 4.00 431.00

Two legs - For 1 Nos. of Line (S/C) per loc 0.00 216.00

Complete Installation of OPGW cable (24/48 fibres) including laying, providing

required hardwares, in line splices to be encased in Fibre Optic Splice Enclosures,

Laying and termination of a fibre optic approach cable required to connect Overhead

15 Fiber Optic Cable (OPGW) between the final iin line splice enclosure on the RKM 2.16 97193.00

gantry/tower and the Fibre Optec Distribution panel (FODP) to be installed within the

building at both the substation ends as per technical specifications

16 Link up of OPGW Cable including all related activities as per inst. Of EIC. RKM 2.16 8850.00

Stringing of ACSR/ AAAC 3 (Three) conductors for single circuit including laying,

jointing, tensioning, clamping with armour rods, hoisting of insulator string fixing of

17 jumpers, dampers etc. & with required tree cutting on entire length for adequate RKM 0.00 56464.00

clearances / safe charging of line, as per instruction of EIC.

-do- but for Stringing of ACSR/ AAAC 6 (SIX) conductors for double circuit.

-do- but for Stringing of ACSR/ AAAC 12 (Twelve) conductors for Multi circuit.

Termination and connection for making LOOP-IN-LOOP-OUT arrangement with

existing line during specified outage including restringing of existing conductors OR

dismantalling / new stringing for making LILO arrangements with existing line or for

change over line as per approved LILO arrangement in profile as per instruction of Job

EIC in COLD CONDITION and dismentalled materials to be credited to near by Work

GETCO's store or sub station as per inst. of EIC.

TOTAL COST PART - B, SCHEDULE - 01 WITHOUT GST

Schedule-2 Work involved in existing Line ( Old line dismentalling)

Description of Supply with Detail Specification of Service Package - Works HSN / SAC FOR Total Cost

B-2 Contract (SAC Code 9954) Unit Quantity Unit Rate (Excl. GST)

Dismantling of any type of tower including transportation & crediting to nearest

1 GETCO’s store or substation as per instruction of EIC. MT 4.00 8434.00

Cutting of stubs of old tower to be dismantled including breaking of chimney/cutting

of RCC upto 450mm below ground level & crediting stubs & steel bars to GETCO's

2 store or substation including back‑filling & leveling of site as per inst. of EIC. 1 12618.00

Dismantling of conductors and line materials of existing line including transportation

3 & creaditing to nearest GETCO's store or substation as per instruction of EIC.: SOR

(A) COLD CONDITION

6 Conductors (D/C) Route

- 1 Earthwire Route

Dismantling of ‘A’ & ‘B’ type ‘H’ frame structure by breaking of muffing upto 450 mm

depth from ground level and cutting the girders from 450 mm depth from ground

4 level by gas cutting & crediting the material to GETCO Store or Substation including Loc. 0 7656

transportation as instructed by Engineer in‑charge.

5 - do – but for ‘C’ type structure. Loc. 0 11055

Dismantling of all three conductors and line materials such as insulators, hardwares

etc. and crediting to the GETCO’s Store or Substation including transporation as per

6 instruction of Engineer in‑charge with submission of pole wise inventory for 0.00 16136

preparing C.R.note.

Dismantling of OPGW cable with require accessories and creadit to GETCO's store

OR Sub station as per instruction of EIC.

TOTAL COST PART - B, SCHEDULE - 02 WITHOUT GST

TOTAL COST PART - B, SCHEDULE - 01 WITHOUT GST

TOTAL COST PART - B, SCHEDULE - 01+02 WITHOUT GST

Service of "Works Contracts" GST @ 18% (SAC 9954)

TOTAL COST PART - B, SCHEDULE - 01+02 WITH GST

1) While calculating the weight of stub-setting, the weight of stub, cleat & templetes shall also be added in stub weight.

2) Red oxide & zinc rich paint shall be applied after tack welding of nuts.

3) The above rates are with supply of cement by the contractor.

4) The rate indicated above includes taking delivery of all stringing materials from Board / Contractor store at destination keeping them in safe custody and

transporting the same to erection site.