PROVISION OF LADDERS FOR OVERHEAD WATER TANKS OF CIVILIAN MD ACCNS (CERA 500-600 LINES) AND ADDITION/ALTERATION OF CUPBOARDS AND DOORS IN MARRIED ACCOMMODATIONS IN CERA (PHASE-II) AT INA EZHIMALA

Amount

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance n exc 50 m and making good surface in hard/dense soil complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

S&F framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similiar work conforming to Fe.290 Gde-E-165 complete all as specified and as directed.

S&F MS plates, channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment (Fe-410W, Gde E-250, Qlty-A) complete all as specified and as directed.

S&F MS anchor fasteners of size 12mm dia and 100mm length for fixing the plates to the wall surface complete all as specified and as directed. Make:- Hilti or equivalent as approved by GE.

M&L for rendering 15mm thick on stone masonry surfaces in cement mortar 1:4 and finish the surface even and smooth complete all as specified and as directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new /old surfaces complete all as specified and as directed.

Taking down chowkats with shutter (without taking off shutter from the frame) exc 1.5 Sqm but n.exc 4.00 Sqm each complete all as specified and as directed.

S&F pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges etc complete all as specified and as directed.

M&L for filling concrete inside frame in PCC 1:3:6 type C-0 complete all as specified and as directed.

S&F 30mm thick 1st class hard wood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats complete all as specified and as directed.

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type both side complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surface exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Dismantling cabinets boarding, any description, fixed in any position with screws incl all fittings complete all as specified and as directed.

S&F stainless steel telescopic channel drawers slides complete all as specified and as directed.

S&F stainless steel soft closing hydraulic hinges for shutter complete all as specified and as directed.

S&F in repair prelaminated particle board 18/19 thick exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

S&F in repair 18/20 mm thick plywood, BWR grade, type BB, fixed with screws to timber frame work as in cupboards etc complete all as specified and as directed.

M&L for preparation of old painted surfaces exc 10cm width or girth and applying one coat of synthetic enamel paint on wooden surfaces complete all as specified and as directed.

M&L for preparation of new or previously untreated wood based surface exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Refixing of shutters of any description exc 1.00 Sqm and n.exc 2.00 Sqm in same opening after easing and adjusting complete all as specified and as directed. Note:- Serviceable shutters obtained from item No.01 above shall be reused.

Resecuring or easing and adjusting without taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and as directed.

S&F in repairs continuous (piano) hinges brass bright finish or electrogalvanised, width of flaps (when open) 30 mm complete all as specified and as directed.

S&F in repairs 40mm dia cupboard knobs fixed with nut, screw and washer of brass, polished complete all as specified and as directed.

S&F in repairs 4 levers brass lock cupboard, grade 1, size 50 mm complete all as specified and as directed.

S&F 75mm long aluminium handles, cast type, anodised complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles fabricated type anodised complete all as specified and as directed.

S&F ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

S&F 75 mm size extruded brass handles, fabricated type polished complete all as specified and as directed.

S&F in repairs 100mm stainless steel butt hinges, cold rolled medium weight complete all as specified and as directed.

S&F in repair 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F in repair 100mm long aluminium, anodised barrel tower bolt of extruded section complete all as specified and as directed.

S&F in repair 150mm long aluminium, anodised barrel tower bolt of extruded section complete all as specified and as directed.

S&F in repairs 100 mm size brass, 4 levers mortise lock, vertical type complete all as specified and as directed.

S&F in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring and overall length of cover plate 140mm complete all as specified and as directed.

S&F in repair 300mm long ordinary MS rat tail rod pattern springs including roller plate complete all as specified and as directed.

General Engineering and Constructions

SANDR

LAKSHMI BUILDERS

KDR CONSTRUCTION

Gates Infra Construction Co

GMS Builders

RS ENTERPRISES