CA NO.CWE BLY/GE (W)/120 OF 2025- 2026SPECIAL REPAIR TO BLDG NO P-105 LOKHART LINE UNDER GE (WEST) BAREILLY

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) n exc 1.50 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.50 sqm but n.exc 4.0 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

S&F pressed steel, frames of size 125mmx60mm x 1.25mm thick for door with one or more rebates including filling and compaction with PCC (1:3:6) Type C-1 using 20 mm graded stone aggregate, necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S&F pressed steel, frames of size 105mmx60mm x 1.25mm thick for door with one or more rebates including filling and compaction with PCC (1:3:6) Type C-1 using 20 mm graded stone aggregate, necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, including pintal etc. complete, drilled for fixing of steel sheeting or othercovering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete confirming to Fe-410- W (Gde- E-250) quality- B complete all as specified and directed.

S&F Steel door including projecting type hinges, steel handle, complete, with glazing bars, dovetailed or welded including flat sheet complete all as specified and directed.

M&L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm coloured PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete as per specified and directed & drawing

S&F in replacement Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F 3.0 mm thick sheet glass ordinary quality and glazing with oil putty or in squares not exceeding 0.50 square metre in each pane complete all as specified and directed.

S&F 3.0mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5sqm in each pane complete all as specified and directed

S&F stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks or galvanised wire stapples complete all as specified as directed.

M&L for galvalised mild steel wire netting of chicken wire mesh 0.46 mm nominal dia of wire & 10 mm mesh size all as spd fixed to walls roof etc complete all as specified and directed.

S&F mild steel framed work such as grills grating etc with ends of bars shouldered and/or riveted or forged into spikes framed guard bars, barrel iron doors ladders framed balusters walk ways railing frame work of water tanks and similar work confirming to Fe -290 Gde-E-165 complete all as specified and directed

S&F for 35 mm thick factory made wooden flush door shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed .

S&F for 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. (Note :- Glass/gauge shall be measured and paid for separately).

S&F in replacements factory made PVC cupboards frame of the size 75 mm x 40 mm with a wall thicknesss of 5 mm made out of extruded 5mm thick plain/prelam PVC sheet of density 600kg/cbm, having bottom width of 50mm and thickness of 10 mm. All four frame lengths reinforced with 15 mm x 15mm M.S.square tubes of 19 quage thickness throughout the frame and mitre cut at two corners adjointed with 2 nos of 15mm long brackets of 10 mm x 10 mm M.S. square tubes. the door frame shall be fixed to the wall using 8/100 long MS screw through the frame by using PVC fastners. A minimum of 4 nos of screws to be provided for each vertical members and minimum of 2 nos of screw to be provided horizontal members etc. complete all as specified and directed, as per manufacturer's specification & drawing.

S&F in replacement factory made PVC cupboards flush type shutter of 30 mm thick consisting of frame made out M S tubes of 19 guage thickness and size 19mm x 19 mm for stiles and rails. The inside panels shall consist of 20 mm thick multichamber hollow PVC section of 1mm wall thickness, bonded using solvent cement / cynoacrylate adhesive with 5mm thick plain/prelam PVC sheet, on both sides of inside panels including necessary item to fix the shutters to frame such as 100 mm stainless steel hinges, 100 mm long handles made of anodised aluminium and magnetic ball catch for each pair of shutters. all four edges of the panels to be sealed with lipping of 10 mm thick and 20 mm wide PVC sheet baton( made by sticking 2nos PVC foam sheet of 5mm thickness using PVC solvent cement adhesive) complete all as specified and directed.

S&F PVC boards 19/20 mm thick any colour as in cabinets including shelves and shutters, fixed with screws and adhesives as per direction of engr-in-charge and manufacturers instructions including piano hinges , magnet catcher, handles etc complete all as specified and directed.

M& L for 125 mm long Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in replacement PVC kitchen frame of section 18x75mm made out of 18mm thick PVC Ply sheet of pleasing colours, print and prelam finishes one side as approved and frame shall be fixed with & including plastic fasteners and 75mm long steel screws inside by using drilling machine complete all as specified and directed.

S&F in replacement PVC kitchen shutter made out of 18mm thick PVC Ply sheet of pleasing colours, print and prelam finishes one side as approved and kitchen shutters shall be fixed to the PVC kitchen frame with & including auto hinges, steel screws and modular handels complete all as specified and directed.

Cutting down existing tree any grith on roof/ wall of bldgs, grubbing roots including necessary cutting and removings penetrated roots and filling holes with cement mortar 1:4 or PCC 1:2:4 type B-1 making good to disturbed portion of brick and cleaning site complete all as specified and directed.

M&L preparation of new wooden surfaces and applying two coats of synthetic enamel paint over one coat of pink primer over 10 cm width or girth complete all as specified and directed.

M& L for Preparation of new iron surface and two coats of synthetic enamel paint ovar a coat of red oxide primer over 10 cm width or girth of any description complete all as specified and directed.

M& L for Preparation of old iron surface and two coats of synthetic enamel paint over 10 cm width or girth of any description complete all as specified and directed.

S & F 100 mm long medium weight, stainless steel Butt hinges ISI marked with screws complete all as specified and directed.

S&F 200mm long mild steel barrel tower bolts, stove enamelled black, with bright bolts complete all as specified and directed.

S & F mild steel pressed handle, oval type, stove enamelled black size of handle 125mm ISI marked .

Supply and fix mild steel, sliding door bolts, bolt type, stove enamelled black, with bright bolt not less than 12 mm dia with and minimum of 6 bolts and nuts, four on bolt plate and two on staple plate length of bolt 300 mm complete all as specified and directed.

S&F mild steel 300 mm long ordinary rat rail rod pattern helical door springs, including roller and roller plate complete all as specified and directed.

S & F 125 mm long Aluminium alloy handles, cast type, anodised complete all as specified and directed.

S & F 150 mm long Aluminium anodised barrel tower bolts of extruded sections complete all as specified and directed.

M & L for brick work with fly ash bricks conforming to IS 12894 -2002 specification straight or curved on plan exc 6 m mean radius built in CM 1:6 including demolition of exiting brick work complete all as specified and directed

M&L for 15mm thick rendering on internal surface in cement mortar 1:6 to on brick masonary wall surfaces on other than fair faces of brick masonary finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering on external surface on fair faces of brick work or concrete surface in cement mortar 1:4 complete all as specified and directed.

M&L for 15mm thick rendering on internal surface in cement mortar 1:6 to on brick masonary wall surfaces on other than fair faces of brick masonary finished even and smooth without using extra cemen including taking down old cement plaster complete all as specified and directed.

M & L for 15 mm thick rendering on external surface on fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth without using extra cement with mixing of water proofing compound as per manufacturer’s instructions but not less than including taking down old cement plaster complete all as specified and directed. (Note:- Water Proofing compound shall be measured and paid seprately).

Supply only liquid water proofing compound conforming to IS specification complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 as on concerete surface on ceilings finished even and smooth without using extra cement including taking down old cement plaster complete all as specified and directed.

M&L for preparation of new plastered surfaces applying three coats of white wash on walls complete all as specified and directed.

M&L for applying two coats of oil bound distempering on newly plastered wall surface with airless electric sprayers over a coat of primer applied using airless electric sprayers over one coat of plaster of paris putty of 1 mm thickness complete all as specified and directed. (Note-APPLICATION TO BE DONE THROUGH AUTHORISED APPLICATOR OF MANUFACTURER.)

M&L for applying two coats of oil bound distempering on newly plastered ceiling surface with airless electric sprayers over a coat of primer applied using airless electric sprayers over one coat of plaster of paris putty of 1 mm thickness complete all as specified and directed. (Note-APPLICATION TO BE DONE THROUGH AUTHORISED APPLICATOR OF MANUFACTURER.)

M&L for preparation of new plastered walls surfaces and applying two coats of Cement based paint over a coat of plaster of paris putty of 1 mm thickness complete all as specified and directed.

Demolition of cement concrete (un reinforced) in ground floor and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for 25 mm thick cement concrete type B0, 1:2:4 (using 12.5 mm graded stone aggregate) in floors, finished rough to receive floor tiles complete all as specified and directed

M&L for 75 mm thick cement concrete 1:3:6, type C1 (using 20 mm graded stone aggregate) as in floor/plinth protection, finish the surface even and smooth without using extra cement including forming necessary joints 12 mm wide to the full depth of PCC at every 3 mtr and every change of direction and filling the same with bitumen filler 1:3 by weight complete all as specified and directed.

M & L for 100 mm thick PCC (1:2:4) type B-1 (using 20 mm graded stone aggregrate laid where required/ directed after applying cement slurry for filling undulationations/ level course finished even and smooth without using extra cement complete all as specified and directed.

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 and dismantling of existing floor, tiling removing rubbish off the premises complete all as specfied and directed.

All as per serial item as above but as in vertical surfaces including rendering 10 mm thick in cement mortar 1:4, dismantling of existing wall, tiling and removing rubbish off the premises as in backing layer complete all as specified and directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 (400x400) sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 and dismantling of existing floor, tiling removing rubbish off the premises scomplete all as specfied and directed.

M&L for Glazed ceramic tiles as in vertical surface 450X 350X 7mm thickset and jointed in neat cement slurry and pointed in white or colour cement to match over and including rendering 10 mm thick in cement mortar 1:4 including dismantling of existing wall tiling and removing rubbish off the premises complete all as specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed.

M&L for 15-18 mm thick Granite work (table rubbed and polished) in steps, jambs, pillars, window-cills, door cills cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with and like in cement mortar (1:4) including form work , pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edging complete all as spd as directed.(shade and coloured of granite will be approved by Engr-in-charge)

M & L for Kota stone slab 18-20mm thick full length in single peice without joint in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade including necessary grinding, rubbing and polishing (mirror finish) and bull nosing over and including rendering of 15 mm thick CM 1:4 complete all as specified and directed.

Demolition of Reinforced cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and direcetd.

Form work to soffits of suspended slabs/chajja/ flat surface of concrete finished rough surfaces of concrete not exceeding 200mm thick,complete all as specified and directed.

M&L for TMT Bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified.

M&L for RCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels complete all as specified and directed.

M&L for RCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in slab supported on wall, beams and columuns in floors, roofs, shelves and stair case etc complete all as specified and directed.

M&L for RCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in Chajjas etc complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks(tripple layer and white in colour) of 500 Litre capacity as per SSR P-I (cylinderical vertical with closed top) hoisted and fixed in position including dismantling of existing old water tank complete all as specified and directed.

S&F 15mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S & F in replacement of 20 mm bore gunmetal globe or gate valve, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F GI tubing of 15 mm dia, medium grade with all fittings and fixed to walls or ceiling (concealed) or laid in floors including taking up or down old existing pipe complete all as specified and directed.

S&F GI tubing of 20 mm dia, medium grade with all fittings and fixed to walls or ceiling (concealed) or laid in floors including taking up or down old existing pipe complete all as specified and directed.

S&F in replacement kitchen sink with drainage board made of stainless steel 1 mm thick with plugs washers and waste pipe and coupling including bedding in cement mortar on dwarf walls including brackets and connecting union to pipe overall size of sink 915 x460 mm and bowl size 410x330x160 mm complete all as specified and directed.

S&F in replacement stainless steel plate rack of overall size 31" x 30" x 10" made with 0.63 mm stainless steel thick sheet complete all as specified and as direcetd.

S & F in replacement Glass shelf assembly with CP brackets complete all as specified and directed.

S & F in replacement Soap dish, any type, fixed to plugs with chromium plated brass screw complete all as specified and directed.

S & F in replacement Vitreous China wash basin , pedestal pattern, size 580x450 including , CP brass waste coupling brass,waste pipe, chain and plug and porcelain stopper brackets complete all as specified and directed.

S & F in replacement Vitreous China water closet Padestal pattern white, including mild steel chromium plated or aluminised hinging device seat cover size 630x450 mm size white with Cast Iron `P' or `S' trap, front or back inlet and including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including lime concrete bedding complete including making good to floor all as specified and directed.

S&F in replacement PVC low level cistern 10 Ltr cap with inlet ball valve, float and handle incl bracket and flush pvc pipe of low or high density or PVC 32 mm dia for low level cistern.

S&F in replacement 15 mm bore dia CP wall mixer with connection, L bend for shower arrangement complete all as spd and directed

S&F in replacement 15mm bore chromium plated fancy type bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in replacement 15 mm bore dia centre hole basin mixture chromium plated complete all as spd and directed

S&F in replacement fancy type chromium plated brass angle valve/Concealed stop cock type suitable for 15mm bore pipe complete all as specified and directed.

S & F in replacement chromium plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union size 125 mm complete all as specified and directed

S&F in replacement 15 mm dia bore PVC connection with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in replacement chromium plated brass tubular towel rail 20 mm dia, D type 60cm long between flanges complete all as specified and directed.

S&F in replacement Grating round 140 mm size of PTMT complete all as specified and as directed.

S & F PVC (SWR) 110 mm dia soil waste or rainwater drainage pipes single socketed in any length with rubber ring joint laid in floor or fixed on wall including taking up or down AC/PVC rain water pipe, soil/waste/vent pipe of any size with fittings etc all as specified or as directed.

S & F PVC (SWR) 75 mm dia soil waste or rainwater drainage pipes single socketed in any length with rubber ring joint laid in floor or fixed on wall including taking up or down AC/PVC rain water pipe, soil/waste/vent pipe of any size with fittings etc all as specified or as directed.

S & F PVC (SWR) 110 mm bore bends all as specified or as directed.

S & F PVC (SWR) 75 mm bore bends all as specified or as directed.

S & F PVC (SWR) junction single,75 mm (Single T) equal or unequal complete all as specified and directed.

S & F PVC (SWR) junction single,100 mm (Single T) equal or unequal complete all as specified or as directed.

S&F in replacement PVC Nahani trap with grating 110mm x 75mm or as per site requirement complete all as specified and directed

S&F in replacement PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

M&L for redering on roof, verticle surfaces of mortar, 15 mm thick, in cement mortar 1:4, over RCC roof slabs for laying water proofing treatment mixed with using water proofing liquid @ 150 ml per 50 kg bag of cement including application of cement slurry over existing roof surface @ 3 Kg/Sqm complete all as specified and directed. (Note:- Water proofing liquid shall be measured and paid separately).

M&L for heavy duty out door type double charged vitrified tiles 10-12 mm thick laid with suitable tile adhesive mortar and painted with suitable water-proof tile joint filler laid over on accessible roof and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Complete removal of existing debris, etc from sunken slab and making good with Providing water proofing treatment to RCC sunken slab as specified and directed as under:- (a) Cleaning the existing RCC sunken slab and vertical wall/RCC beam and hacking the surface. (b) 15mm thick plastering over the floor & vertical surface in CM 1:4, mixed with liquid water proofing compound @ 200ml per 50 kg of cement trowelled to even and smooth finish without using extra cement . (c ) filling the sunken portion with water for 72 hrs and carring out the ponding test.(Any leakage /seapage noticed shall be repaired). (d) Applying two coats of elastomaric acrylic water proof coating Make: Dr. Fixit of pidilite or equivalent per sqm in each coat with roller application.(Note: Each coat of elastomaric acrylic compound requires 6-8hrs to dry up itself second coat shall be applied on getting the first coat completely dried up) and filling with PCC 1:5:10 using 40 mm grade stone aggregate complete all as specified and directed.

S&F 25 mm dia SS fancy type droppery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required including fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate size in each end & intermediate support complete all as specified and directed.

M&L for Providing & injecting chemical for post construction ATT at the junction of the wall and floor where the apron is not provided using chemical emulsion @ 7.5 litres per sqm of the vertical surface of the sub-structure to a depth of 300 mm including excavating channel along the wall and rodding etc. complete all as specified and directed.

Surface excavation in soft /loose soil n. exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed.

Removing surplus excavated materials (SOIL) to distance not exceeding 50 m and depositing where directed at a level n. exc 1.50 m above the starting point complete all as specified and directed.

M & L 100 mm thick PCC 1:3:6 type C-2 as in sub base, Floors, Paving, finished even and fair with out using extra cement complete all as specified and directed.

M&L for Sand filling under floors or in foundations or for cushing of UG cable including watering and consolidation complete all as specified and directed.

M&L for Machine pressed Precast cement coloured concrete, factory made coloured glazed interlocking paver block any shape and size conforming to IS 15658 -2006 of 60mm thickness, M-35 Grade, pattern and colour with grey cement & pigment complete all as specified and directed.

Taking down carefully unserviceable copper/aluminium point wiring (Light, fan, socket or power) complete including unserviceable fittings and fixtures such as switches, ceiling roses, pendents, regulators, sockets, lamp holders, brackets, except ceiling fittings, bulk head fittings, tube light fittings etc. and making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down old MCB DBs/ main switches off size complete all as specified and directed

Taking down or out old sub main copper/aluminium cable off various sizes from existing conduit/ batten complete all as specified and directed.

M&L for wiring with and including multi stranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLSH cable, 1100 volts grade, ISI marked with valid CML number, drawing through in and including medium grade, rigid non metallic, PVC concealed conduit of 20mm bore and including cutting chases for conduits and sinkings for boxes, its accessories & including with multi stranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLSH cable, 1100 volts grade, ISI marked with valid CML number as continuity earth wire terminating with new sunken concealed terminal boxes complete all as specified and directed for the following :- (a) One light/fan/Bell point controlled by one switch

(b) One multi pin socket outlet, 5/6 Amps, on Independent board.

(c) One 3 pin, 5/6 Amps, socket outlet on the same board, controlled by another switch.

(d) One buzzer/ bell point controlled by one push button on the same board with other switches or independent complete all as specified and directed

M&L for wiring with and including multi stranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLSH cable, 1100 volts grade, ISI marked with valid CML number, drawing through in and including medium grade, rigid non metallic, PVC concealed conduit of 20mm bore and including cutting chases for conduits and sinkings for boxes, its accessories & including with multi stranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLSH cable, 1100 volts grade, ISI marked with valid CML number as continuity earth wire terminating with new sunken concealed terminal boxes complete all as specified and directed.

S & F Modular switch one way 6 A, 1 Module complete all as specified and directed.

S & F Modular switch one way 16 A, 1 Module complete all as specified and directed

S & F Modular bell push 6 Amp, 1 Module complete all as specified and directed

S & F Modular Socket 6 Amp, 2/3 Pin combined 2 Module complete all as specified and directed

S & F Modular Socket 6/16 Amp, 2/3 Pin combined 2 Module complete all as specified and directed.

S&F Modular fan regulator Step up type, 120 Watt, 2 Module complete all as specified and directed

S&F, ceiling rose, 3 terminal , any shade, of PVC/Polycarbonate, isolated body complete all as specified and directed

M & L for replacement of lamp holder, PVC / Poly carbonate, insulated body modular type with back plate batten/angle type for batten fittings complete all as specified and directed

S&F in replacement LED mirror light fitting of 1 x 10 watt LED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed.

S&F in replacement LED mirror light fitting of 1 x 20 watt LED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed.

S&F indoor decorative LED City-3 light fitting suitable for & including single 12 Watt LED lamp with polycarbonate body with upper globe complete all as specified and directed.

Supply and Fix LED lamp 12 Watt, 230 V , AC integrated circuit complete all as specified and directed.

Supply and fixing Buzzer, Ding Dong AC. 230 volts,single pole complete all as specified and directed

Supply & Fixing security light fitting, LED type, 25 Watt, 6000 K, pressure die cast housing with prismatic polycarbonate diffuser & indvl LEDs as light source with integrated electronic driver complete with M&L GI pipe mounting bracket of size 25/32 mm dia and 1.20 m long fixed to wall with and including nut, bolts and GI clamps of size 50 x 6 mm as required including two coats of synthetic enameled paint over a coat of primer and making connection with three core 23/.0076 rubber insulated copper cable from ceiling rose to connector of street light complete all as specified and directed.

M&L for sub main wiring with two single core 6.0 Sqmm (FRLS) copper conductor PVC unsheathed cable medium grade including PVC conduit (appropriate size) concealed in wall for sub main connection including 6.0 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified. ( Note :- Two runs of 6.0 sqmm (FRLS) and one run of 6.0 sqmm (FRLS) copper conductor shall be measured as one unit length.)

Taking down carefully ceiling fan from existing site and doposited in MES yard for BER in coming BOO all as directed by Engineer-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as specified and directed.

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed.

S&F MCB SPN 40 Amp 240 volt complete all as specified and directed by the Engr-in-Charge.

S&F MCB single pole 6 to 32 Amp 240 Volt 'B' curve 10 KA complete all as specified and directed by the Engr-in-Charge.

Supply and fix flush sheet metal enclosure SPN DB 6 way with double door IP-42 protection detachable gland plates, flush mounting for MCB fitted with bus bar , earth bar and neutral links complete all as specified and directed.

Supply and fix TPN DB -TPN DB 4 way with provn and including of MCCB 63 Amps , 415 Volt, 3 Phase, 4 wire AC 50 Hz having aluminium Bas Bar phase and the neutral insulated with PVC sleeves, connected with appropriate size copper thimbles.

Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) of TPN/FP 40 to 100 AMP current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed by the Engr-in-Charge.

Material & Labour for earthing complete including taking out old unsv and replace with galvanised steel earth plate 600x600x 6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate using 4 mm dia GI wire as earth wire electrode moulded and rivetted to earth plate at one end and connected to main switch/ control switches of buildings at another end, GI earth wire encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto main switch board of building including 20 dia bore GI pipe 'light grade' as water pipe from earth chamber and including excavation and earth work, PCC 1:3:6 type C1 chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced complete all as specified and directed

Taking down carefully service connections of any dsecription from pole, wall or service brackets etc including making good disturbed surface to match with the existing surface complete all as specified and directed.

Supply and laying & testing UG cable XLPE, insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor , of size 25 Sqmm 4 core complete all as specified and directed.

Excavation in trenches n. exc 1.5 mtr wide and not exc 1.5 mtr in depth for laying under ground LT XLPE cable and getting hard/ dense soil complete all as specified and directed.

M&L Returning , filling in including spreading, levelling, watering and well ramming in laying not exceeding 25 cm thick in soft/loose soil complete all as specified and directed.

M&L Removing excavated material (soils) to a distance not exceeding 50 m and depositing whare directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M&L for river fine sand, washed and screened dry for caushioning to under ground cable in trenches below and around under ground cable including spreading and levelling punning complete all as specified and directed.

M&L for laying bricks, sub class 'B' old size for protection of cable, in trenches, laid in dry flat across the cable with length of whole bricks complete all as specified and directed.

S&F GI tubes light grade of dia 80 mm bore dia with all fitting and fixed complete for protection of LT UG Cables laid to walls or in floors or along with poles etc complete all as specified and directed.

Please Enable Macros to View BoQ information