Construction of Science College at Kalgam Ta. Umergam Dist. Valsad

No figures

1 Excavation for foundation upto 1.5 m depth including sorting out 6383.00 Cumt 117.09

and stacking of useful materials and disposing off the excavated

stuff upto 50 Meter lead.(A) Loose or soft soil

2 Excavation for foundation upto 1.5 to 3 m depth including sorting 2068.00 Cumt 162.56

out and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead.(C) Dense or Hard soil

3 Filling in foundation and plinth with sand in layers of 20 cm. 439.00 Cumt 460.19

Thickness including watering ramming and consolidating etc.

layer of 20 cm in thickness including ramming watering and

consolidating etc. complete

5 Anti-Termite System:Providing and laying of permanent piping 2151.00 Sqmt 63.63

technology anti-termite treatment before flooring work by

installing LLDP (Low linear density polyethylene) tube of 8 mm

O.D. & 6.4 mm 1.D. with inbuilt pressure compensation chip every

30 cm interval in the tube, having working pressure of 2 Kg/cm2

and release rate of 1.9 Itr/hour fixed by P-clips and nails. The

LLDP pipe shall be installed at the entire periphery of the building

and at internal network of building at a depth of 20 to 200 mm

under floor at every 2 to 3 mtr. c/c distance (adjusted as per

building layout ) & Ends of loop pass through a PVC elbow of

minimum 32 mm ID at junction box of wall and floor level,

entering into a steel reinforced grooved flexible pipe of minimum

22 mm ID leading into junction box and the loops shall terminate

in junction boxes & test every junction during injecting chemicals

for termite control treatment. The anti termite chemical

Imidacloprid 30.5% SC mix as per IS- 6313 (part III) shall be

injected by the pressure pump diluted with water @ 10.5 ml/5 ltr

of water at the rate of 2 Kg/sq.cm @ 5 Ltr/SMT. The contractor

shall submit approved line plan for piping system and junction

boxes dully approved by Engineer-in-Charge with bond of 5 year

warranty.(II)Anti Termite chemical injected area (Chemical

injecting incl. labour cost)

6 Providing and laying controlled cement concrete M.150 and 1036.00 Cumt 3894.06

curing complete including the cost of formwork and excluding

reinforcement for reinforced concrete work in (A) Foundations

and plinth pcc

7 Providing and laying controlled cement concrete M.250 and 2735.61 Cumt 4590.45

curing complete including the cost of formwork and excluding

reinforcement for reinforced concrete work in (A) Foundations,

footings, and Mass concrete. footing

8 Providing and laying controlled cement concrete M-250 and 53.00 Cumt 7429.56

curing complete including the cost of form work but excluding the

cost of reinforcement for reinforced concrete work in (d) columns

Up to Plinth level.

9 Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse 444.00 Cumt 3005.76

sand : 6- machine cut stone aggregates 40 mm nominal size) and

curing complete excluding cost of formwork in (A) Foundation

and Plinth

Item Rate In

Description of Item Quantity Unit Amount

No figures

10 Providing and laying controlled cement concrete M-200 and 163.00 Cumt 7403.30

curing complete including the cost of form work but excluding the

cost of reinforcement for reinforced concrete work in Columns,

pillars posts and struts G.FLOOR

11 Providing and laying controlled cement concrete M-200 and 66.00 Cumt 7403.30

curing complete including the cost of form work but excluding the

cost of reinforcement for reinforced concrete work in Columns,

pillars posts and struts F.FLOOR

12 Providing and laying controlled cement concrete M-200 and 66.00 Cumt 7443.70

curing complete including the cost of form work but excluding the

cost of reinforcement for reinforced concrete work in Columns,

pillars posts and struts S.FLOOR

13 Providing and laying controlled cement concrete M-200 and 30.00 Cumt 7484.10

curing complete including the cost of form work but excluding the

cost of reinforcement for reinforced concrete work in Columns,

pillars posts and struts T.FLOOR

14 Providing and laying controlled cement concrete M-250 and 459.02 Cumt 4832.62

curing complete including the cost of form work but excluding the

cost of reinforcement for reinforced concrete work in Ground &

Plinth BEAMS

15 Providing and laying controlled cement concrete M-150 and 330.50 Cumt 5160.09

curing complete including the cost of form work but excluding the

cost of reinforcement for reinforced concrete work in plinth Slab

16 Providing and laying controlled cement concrete M.200 and 354.00 Cumt 6122.62

curing complete including the cost of formwork and excluding

reinforcement for reinforced concrete work in (C) Ground floor

17 Providing and laying controlled cement concrete M.200 and 317.00 Cumt 6122.62

curing complete including the cost of formwork and excluding

reinforcement for reinforced concrete work in (C) F.floor Beams,

18 Providing and laying controlled cement concrete M.200 and 319.00 Cumt 6162.01

curing complete including the cost of formwork and excluding

reinforcement for reinforced concrete work in (C) S floor Beams,

19 Providing and laying controlled cement concrete M.200 and 8.00 Cumt 6202.41

curing complete including the cost of formwork and excluding

reinforcement for reinforced concrete work in (C) T floor Beams,

20 Providing and laying controlled cement concrete M-200 and 12.00 Cumt 6725.59

curing etc. complete including the cost of form work and

reinforcement for reinforced concrete work in (c) Chhajja for

Ground floor

21 Providing and laying controlled cement concrete M-200 and 10.00 Cumt 6725.59

curing etc. complete including the cost of form work and

reinforcement for reinforced concrete work in (c) Chhajja for First

22 Providing and laying controlled cement concrete M-200 and 11.00 Cumt 6765.99

curing etc. complete including the cost of form work and

reinforcement for reinforced concrete work in (c) Chhajja for

second floor

23 Providing and laying controlled cement concrete M-200 and 1.00 Cumt 6806.39

curing etc. complete including the cost of form work and

reinforcement for reinforced concrete work in (c) Chhajja for

third floor

24 Providing and laying controlled cement concrete M-200 and 13.00 Cumt 8499.15

curing etc. complete including the cost of form work and

reinforcement for reinforced concrete work in (c) Lintal for

Ground floor

Item Rate In

Description of Item Quantity Unit Amount

No figures

25 Providing and laying controlled cement concrete M-200 and 10.00 Cumt 8499.15

curing etc. complete including the cost of form work and

reinforcement for reinforced concrete work in (c) Lintal for First

26 Providing and laying controlled cement concrete M-200 and 11.00 Cumt 8539.55

curing etc. complete including the cost of form work and

reinforcement for reinforced concrete work in (c) Lintal for

Second floor

27 Providing and laying controlled cement concrete M-200 and 7.00 Cumt 8579.95

curing etc. complete including the cost of form work and

reinforcement for reinforced concrete work in (c) Lintal for Third

28 Providing and laying controlled cement concrete M.200 and 295.50 Cumt 6502.38

curing complete including the cost of formwork and excluding

reinforcement for reinforced concrete work in (C) Ground floor

29 Providing and laying controlled cement concrete M.200 and 281.00 Cumt 6502.38

curing complete including the cost of formwork and excluding

reinforcement for reinforced concrete work in (C) First Floor slab

30 Providing and laying controlled cement concrete M.200 and 281.00 Cumt 6542.78

curing complete including the cost of formwork and excluding

reinforcement for reinforced concrete work in Second Floor slab

31 Providing and laying controlled cement concrete M.200 and 9.00 Cumt 6583.18

curing complete including the cost of formwork and excluding

reinforcement for reinforced concrete work in Third Floor slab

32 Providing and laying controlled cement concrete M-200 and 15.00 Cumt 6973.04

curing etc. complete including the cost of form work and

excluding the cost of reinforcement etc. complete in (E) Stair case

for Ground Floor to first floor

33 Providing and laying controlled cement concrete M-200 and 7.00 Cumt 6973.04

curing etc. complete including the cost of form work and

excluding the cost of reinforcement etc. complete in (E) Stair case

for First Floor to Second floor

34 Providing and laying controlled cement concrete M-200 and 7.00 Cumt 7012.43

curing etc. complete including the cost of form work and

excluding the cost of reinforcement etc. complete in (E) Stair case

for Second to third floor

35 Providing and laying controlled cement concrete M-200 and 5.00 Cumt 8722.36

curing etc. complete including the cost of form work and

excluding the cost of reinforcement etc. complete in RCC Vertical

and horizontal wall for Below Plinth & Ground floor

36 Providing and laying controlled cement concrete M-200 and 48.00 Cumt 8722.36

curing etc. complete including the cost of form work and

excluding the cost of reinforcement etc. complete in RCC Vertical

and horizontal wall for G.floor

37 Providing and laying controlled cement concrete M-200 and 8.00 Cumt 8761.75

curing etc. complete including the cost of form work and

excluding the cost of reinforcement etc. complete in RCC Vertical

and horizontal wall for F.floor

38 Providing and laying controlled cement concrete M-200 and 8.00 Cumt 8761.75

curing etc. complete including the cost of form work and

excluding the cost of reinforcement etc. complete in RCC Vertical

and horizontal wall for S.floor

39 Providing and laying controlled cement concrete M-200 and 8.00 Cumt 8802.15

curing etc. complete including the cost of form work and

excluding the cost of reinforcement etc. complete in RCC Vertical

and horizontal wall for T. floor

Item Rate In

Description of Item Quantity Unit Amount

No figures

40 Providing and fixing 90 cm high Stainless steel railing made from 44.00 Rmt 3719.83

anticorrocive 304 grade S S pipe of 50 mm dia (16Gauge) as hand

rail with S S 304 grade Baluster of 38 mm dia (16Gauge) as a

vertical support fixed in RCC slab at 1.2m c/c including three

horizontal S S pipes of 25 mm dia (16Gauge) at eqal distance fixed

by 18.75 mm dia (16Gauge) S S pipe with baluster including

accessories as per detailed drawing as directed etc. complete.

41 Providing and Fixing S.S Hand Rail made SS 304 of 50 mm inside 225.00 Rmt 1532.37

dia 16 guage round pipe supported with 8 mm thick SS 304 base

flange on wall including end S.S ball 75mm dia, anchor fasteners,

nuts, accessories as per detailed drawing etc. complete as

directed by Architect or Engineer in charge.

42 Providing TMT Bar FE 550D reinforcement for R.C.C. work 756242.00 Kg 95.26

including bending, binding and placing in position complete upto

floor top level

43 Providing and fixing eco-friendly light weight calcium silicate 1071.00 Sqmt 1648.96

false ceiling tiles having Tegular edge & 15 mm Thick Densified

edges on the Tile Periphery for Extra Strength The Light weight

calcium silicate ceiling tiles shall have, light reflection 85% non-

combustible as per B.S. 476 part IV, 100% humidity resistance

and also having thermal conductivity0.043° w/m KC.for the best

thermal Insulation. The Light weight calcium Silicate tile shall be

of approved texture Fine fissured/ Spintone/ Cosmos having NRC

value of 0.5 & Globe having NRC value of 0.75 NRC or equivalent

of size 595 X 595 mm to be laid on true horizontal level

suspended inter locking metal grid of hot dipped galvanized steel

sections (galvanizing @120 grams per sqm including both side)

consisting of main ‘T’ runner suitably spaced at joints to get

required length and size of 24 X 38mm made from 0.30 mm thick

(minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size

24 X 28mm made out of 0.33mm (Minimum) sheet spaced

1200mm along spaced between main 'T' at 600mm centre to

centre to form agrid of 1200x600mm and size 24x48mm made of

0.30mm thick (Minimum) sheet to be interlocked at middle of the

1200x600mm panel to form grid of size 600x600mm resting on

periphery walls/partitions on a perimeter wall angle pre-coated

steel of size (24x24x3000mm made of 0.40mm thick (minimum)

sheet with the help of rawl plugs at 450mm centre to centre with

25mm long dry wall screws @ 230mm interval and laying 15mm

thick densified edges light weight calcium silicate ceiling tiles of

approved texture (Fine fissured/Cosmos/Spintone) in the grid

including cutting/making opening for services like diffusers, grills,

light fittings, fixtures, smoke dtectors etc., wheneveer required,

Main 'T' runners to be suspended from ceiling using G.I. slotted

cleats of size 25x35x1.6mm fixed to ceiling with 12.5mm dia and

44 Brick work using common burnt clay building bricks having 405.00 Cumt 4021.02

crushing strength not less than 35 kg/sq.cm. in foundation and

plinth in cement mortar 1:6 (1 cement : 6 fine sand) Conventional

45 Brick work using common burnt clay building bricks having 645.00 Cumt 4295.99

crushing strength not less than 35 Kg/Sq.cm. in super structure

above plinth level upto floor two level in cement mortar 1:6

(1cement : 6 fine sand) Conventional {Ground FLoor}

46 Brick work using common burnt clay building bricks having 381.00 Cumt 4295.99

crushing strength not less than 35 Kg/Sq.cm. in super structure

above plinth level upto floor two level in cement mortar 1:6

(1cement : 6 fine sand)Conventional {First FLoor}

Item Rate In

Description of Item Quantity Unit Amount

No figures

47 Brick work using common burnt clay building bricks having 312.00 Cumt 4336.18

crushing strength not less than 35 Kg/Sq.cm. in super structure

above plinth level upto floor two level in cement mortar 1:6

(1cement : 6 fine sand)Conventional {Second FLoor}

48 Brick work using common burnt clay building bricks having 74.00 Cumt 4376.37

crushing strength not less than 35 Kg/Sq.cm. in super structure

above plinth level upto floor two level in cement mortar 1:6

(1cement : 6 fine sand)Conventional {third FLoor}

49 Half brick masonry in common brunt clay building bricks having 650.00 Sqmt 653.01

crushing strength not less than 35Kg/Sm. In C.M 1:4( 1cement :

coarse sand) in super structure. Conventional for Ground floor..

50 Half brick masonry in common brunt clay building having 679.00 Sqmt 653.01

crushing strength not less than 35Kg/Sm. In C.M 1:4( 1cement :

coarse sand) in super structure.Conventional for first floor.

51 Half brick masonry in common brunt clay building having 530.00 Sqmt 659.00

crushing strength not less than 70Kg/Sm. In C.M 1:4( 1cement :

coarse sand) in super structure.Conventional for Second floor.

52 Half brick masonry in common brunt clay building having 147.00 Sqmt 665.00

crushing strength not less than 35Kg/Sm. In C.M 1:4( 1cement :

coarse sand) in super structure.Conventional for Third floor.

53 Providing and fixing 150 mm wide, approved quality chicken wire 2723.00 Sqmt 360.77

mesh at junction of brick work and RCC work or two dissimilar

surfaces, at all heights fixed by nails, rowal plugs or tag by cement

mortar 1:3 before applying the plaster, including curing, s

54 Providing 15mm thick Smooth cement plaster in single coat on 3980.00 Sqmt 201.40

Rough (Similar) side of single or half birck walls / concrete wall

for interior plastering and finished even and smooth in C M 1:4 (1

cement : 4 coarse sand) with floting coat of neat cement slurry

etc. comp. For Ground floor

55 Providing 15mm thick Smooth cement plaster in single coat on 4047.00 Sqmt 201.40

Rough (Similar) side of single or half birck walls / concrete wall

for interior plastering and finished even and smooth in C M 1:4 (1

cement : 4 coarse sand) with floting coat of neat cement slurry

etc. comp. For first floor

56 Providing 15mm thick Smooth cement plaster in single coat on 4165.00 Sqmt 224.80

Rough (Similar) side of single or half birck walls / concrete wall

for interior plastering and finished even and smooth in C M 1:4 (1

cement : 4 coarse sand) with floting coat of neat cement slurry

etc. comp. For second floor

57 Providing 15mm thick cement plaster in single coat on Rough 439.00 Sqmt 248.19

(Similar) side of single or half birck walls / concrete wall for

interior plastering and finished even and smooth in C M 1:4 (1

cement : 4 coarse sand) with floting coat of neat cement slurry

etc. coThird floor

58 Providing 10 mm. Thick smooth cement plaster in single coat for 2091.00 Sqmt 189.15

plastering on ceiling and soffits of stairs and finished even and

smooth in : (I) Cement mortar 1:4 (1 cement : 4 sand) with floting

coat of neat cement slurry etc. complete.Ground Floor

59 Providing 10 mm. Thick smooth cement plaster in single coat for 1948.00 Sqmt 189.15

plastering on ceiling and soffits of stairs and finished even and

smooth in : (I) Cement mortar 1:4 (1 cement : 4 sand) with floting

coat of neat cement slurry etc. complete. First Floor

60 Providing 10 mm. Thick smooth cement plaster in single coat for 1944.00 Sqmt 212.54

plastering on ceiling and soffits of stairs and finished even and

smooth in : (I) Cement mortar 1:4 (1 cement : 4 sand) with floting

coat of neat cement slurry etc. complete second Floor

Item Rate In

Description of Item Quantity Unit Amount

No figures

61 Providing 10 mm. Thick smooth cement plaster in single coat for 64.00 Sqmt 235.94

plastering on ceiling and soffits of stairs and finished even and

smooth in : (I) Cement mortar 1:4 (1 cement : 4 sand) with floting

coat of neat cement slurry etc. complete third Floor

62 20mm thick double coat sand faced cement gutka plaster on walls 10518.00 Sqmt 300.66

upto height 10 metres above ground level consisting of 12mm

thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick

finishing coat of C.M. 1:1 (1-cement : 1-sand) including 1cm x 1cm

grooves etc. complete.

63 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 737.00 Rmt 42.17

64 Applying two coats of (white cement based) or (acrylic lappy 18337.00 Sqmt 40.59

(putty)) or equivalent and two coats of primer of approved brand

and manufacture on new wall surface to give an even shade

including thoroughly brushing the surface free from mortar

dropping and other foreign matter and sand papered smooth. for

All floor.

65 Wall painting (two coats) with plastic emulsion paint of approved 12294.00 Sqmt 80.35

brand and manufacture on undecorated wall surface to give an

even shade including throughly brushing the surface free from

mortar droppings and other foreign matter and sand papered

66 Wall painting (two coats) with plastic emulsion paint of approved 6043.00 Sqmt 85.76

brand and manufacture on undecorated ceiling surface to give an

even shade including throughly brushing the surface free from

mortar droppings and other foreign matter and sand papered

67 Finishing wall with Weather proof exterior 100% acrylic 10493.00 Sqmt 114.53

emulsion paint With one coat of primer on wall surface to give an

required shape even shade after thoroughly brushing the surface

to remove all dirt, and remains of loose powdered materials.etc

complete for All floor

68 Providing And filling with good quality cinder(steam coal) as 104.00 Cumt 691.85

directed by engineer in charge in sunks in layers of 15 cm

thick,including watering,placing ,ramming well etc as directed, for

all floor.

69 Providing and laying water proofing treatment by conventional 148.00 sqmt 1005.96

method including cleaning the slab surface by wire brush as

directed including provding first layer of C.M. 1:4 of 40 mm

thickness mixed with water proofing compound at rate

prescribed by manufacturer, including putting of brick bats of

average thickness 40 mm Well immerssed in water laid uniformly

on first layer of mortar including applying cement slurry @ rate of

0.08 bag/sqm. on fixed layer of brick bats including maintaining

necessary slope, in second layer 40 mm thick C.M 1:4 mixed with

water proofing compound as directed, including finishing smooth

with cement slurry as directed complete.

70 Providing and laying controlled cement concrete M-200 for RCC 69.75 Cumt 5283.31

work and curing complete including the cost of form work but

excluding the cost of reinforced concrete work in coping on

Ground Floor

71 Providing and laying controlled cement concrete M-200 for RCC 7.00 Cumt 5283.31

work and curing complete including the cost of form work but

excluding the cost of reinforced concrete work in coping on First

72 Providing and laying controlled cement concrete M-200 for RCC 5.00 Cumt 5323.71

work and curing complete including the cost of form work but

excluding the cost of reinforced concrete work in coping on

Second Floor

Item Rate In

Description of Item Quantity Unit Amount

No figures

73 Providing and laying controlled cement concrete M-200 for RCC 11.00 Cumt 5364.11

work and curing complete including the cost of form work but

excluding the cost of reinforced concrete work in coping on third

74 Providing and fixing window having extruded aluminumColour 15.00 Sqmt 2140.33

anodized section frame main outer size 127mm x38.10mm x

1.35mm @wt. 1.384kg/m, horizontal Four track member size

122.20mm x 31.75mm x 1.10mm@ wt1.205 kg/m, vertical

member of size 122.20mm x31.75mm x 1.50mm @1.398 kg/mt

with sliding shuttersof horizontal member size 40mm x 18mm x

[email protected]/mt ,vertical member of size 40mm x 18mm

x1.29mm @ 0.456 kg/mt with 5 mm thick transparentbronze

colour tinted float glass with powder coatedaluminum fittings

and fixtures and transparent siliconsealant glass fixing to frame as

per details etc completefor window

75 Providing and fixing window having extruded aluminumColour 262.00 Sqmt 1583.95

anodized section frame main outer size 95mm x24mm x 1.17mm

@ wt.of 0.738 Kg/mt , horizontal Three track member size 92mm

x 31.75mm x 1.30mm,@Wt.1.07 Kg/mt , vertical member of size

92mm x31.75mm x 1.50mm @ Wt. 1.06 Kg/mt with

slidingshutters of horizontal member size 40 mmx18mmx1.29mm

@ wt.of 0.456 Kg/mt, vertical member of size40mm x 18mm x

1.29 mm @ wt.of 0.456Kg/mt/ with 5mm thick transparent

bronze colour tinted float glasswith powder coated aluminum

fittings and fixtures andtransparent silicon sealant glass fixing to

76 frame as perdetails

Providing etc

& Fixing in position standard extruded approved colour 163.00 Sqmt 3004.75

anodised Aluminum Ventilator with outer frame 63.50 x 38.10 x

1.95 mm @ Wt 1.094 kg/Rmt with 3mm thick Bajari figure

adgesteble tinted louvers glass fixed to alluminium strip blade

including fixtures, fastenning, labours and equipments as per

detailed drawing as directed. For Ventilators W3 V1 V3

77 Providing & Fixing in position standard extruded approved colour 17.00 Sqmt 3336.03

anodised Aluminum Ventilator with outer frame 63.50 x 38.10 x

1.95 mm @ Wt 1.094 kg/Rmt with 6mm thick Dark glass pannel

fixed to alluminium strip blade including fixtures, fastenning,

labours and equipments as per detailed drawing as directed. For

Ventilators V2

78 Providing and fixing 38 mm thick flush double door shutter, solid 226.00 Sqmt 4673.27

core with Anodized Aluminium section (jindal door section no

19552-weight not less than 1.1 kg/mt ) frame size 63.5mm x

38mm inserted Non teak wood frame inside the aluminium

section for durable grip of hinges & Double shutter with

required teakwood batten having 1mm thick lamination on both

side, Durable Grip shall be providing with both side 15cm long

stainless steel handle and necessary Locking system of Godrej,

,fixtures & fastenings etc. directed by engineer in charge. D1

79 Providing and fixing 38 mm thick flush single door shutter, solid 45.00 Sqmt 4628.83

core with Anodized Aluminium section (jindal door section no

19552-weight not less than 1.1 kg/mt ) frame size 63.5mm x

38mm inserted Non teak wood frame inside the aluminium

section for durable grip of hinges & Double shutter with

required teakwood batten having 1mm thick lamination on both

side, Durable Grip shall be providing with both side 15cm long

stainless steel handle and necessary Locking system of Godrej,

,fixtures & fastenings etc. directed by engineer in charge. D,D3

Item Rate In

Description of Item Quantity Unit Amount

No figures

80 Providing and fixing FRP frame size 100 x 50 mm and 35 mm 46.00 Sqmt 2362.39

thick FRP depress panel single/Double shutter having extra

reinforcement on sides & edges in Gel coat finish.The core of the

shutter & frame is to be filed up with injected fire retradat grade

polyurethene foam done in situ along with embeded wooden

pieces for stiffening & also taking hinges & fintures.The whole FRP

frame & shutter is to be waterproof, weatherproof ,termite proof

& resistance to mild acid/alkali.Rates are to be inclusive of S.S

hinges with necessary screws & alluminum fixtures & fastenings

& fartener sleeve.Colour and Shade approved by Engineer-In-

Charge.D5,

81 P & L 60x60 cm Mirror polished Blue Kota Stone slab flooring 5144.00 Sqmt 1029.22

over 20 mm (average)thick base of cement mortar 1:6 (1-cement

6-coarse sand) or L.M 1:1.5 (1 Lime putty : 1.5 coarse sand laid

over and jointed with grey cement slurry mixed with pigment to

match the shade of slab including rubbing and polishing

etc.complete (A) 30mm thick

82 P & L 60x60 cm Mirror polished Blue Kota Stone slab 30 mm 189.00 Sqmt 1089.67

thick in riser of steps,skirting dedo and pillars laid on 10 mm

thick cement mortar 1:3 (1-cement 3-coarse sand) and jointed

with grey cement slurry mixed with pigment to match the shade

of slab including rubbing and polishing etc.complete(30 mm thick)

83 P & L Mate Finished antiskid ceramic tiles 30 x 30 cm size 6 mm 213.00 Sqmt 970.07

thick in flooring treads of steps and landing laid on a bed of

mm thick cement mortar 1:3(1-cement:3-coarse sand)finishing

with flush pointing in white cement

84 P & L premium printed glazed tiles tiles size 30 x 60 cm 6 mm 587.00 Sqmt 1441.22

thick in skirting risers of steps and dedo on 10 mm thick cement

plaster 1:3 (1-cement:3coarse sand) and jointed with colour

cement slurry

85 Providing and laying machine cut free edge machine polished 173.00 Sqmt 929.20

Blue kota stone 25mm thick finished treads and risers in Max

cm length with 1cm projecting, nozing rounded moulding in tread

laid over 12 mm (av.) thick bases of cement mortar 1:6 (1-cement

: 6-coarse sand) jointed with grey or colour cement slurry

including rubbing and polishing incl. making Three No.s of

grooves of size 3mm X 3mm along the length of treads etc.

86 Providing Plinth Protection to Building including excavation in 452.00 Sqmt 2402.49

ordinary soil and laying cement concrete 1:3:6 using stone

aggregates of 40mm nominal size in foundation layer 125 mm

thick+ 125mm thick sand layer below pre-cast Rubber Dye inter

locking concrete block 60mm thick with grade of concrete M300

pneumatic compressed by mechanically pressed and as per

approved design including 75mm Sand layer for levelling and

filling the joint with sand in proper line and level etc. complete,

Including Providing and fixing pre-cast concrete kerb stone of

grey cement based concrete block 30cm length, 30cm height and

15cm thick made of M250 grade concrete as per approved design

and including excavation for fixing in proper line and level, filling

the joint with C:M 1:3 (1cement:3 fine sand) etc. complete.

87 Providing and laying broken chine mosaic flooring for terrace 2188.00 Sqmt 747.29

using 12 mm to 20 mm broken pieces of glazed tiles to be laid

over cement mortar 1:3 to plain or slope and to be tempered to

bring mortar creme out upto surface using white cement

including rounding off junctions and extending them upto 15 cm

along the wall,clearing with water and oxalic acid etc. as directed

Item Rate In

Description of Item Quantity Unit Amount

No figures

88 Providing and laying cement concrete flooring 1:2:4 (1-cement : 2- 2188.00 Sqmt 322.93

coarse sand : 4-graded stone aggregate 20mm nominal size) laid

in one layer and finished with a floating coat of neat cement. (A)

50mm thick.

89 Providing and fixing mirror polished 18 mm thick Green Marble 830.00 Sqmt 1317.04

stone with full round edge and polished of approved quality in

clading on sill and around the doors/ windows/ ventilation with

20 mm thick cement plaster CM (1:4) and fixing with cement

slurry & adhesive including moulding of exposed edges as

directed by engineering in charge etc. complete.

90 Providing and fixing M.S Safty Grills having 16mm MS bar 458.00 Sqmt 3392.59

Horizontally at every equal 0.10m C/C distance and 2 no of bar

Vertically at every equal 0.375m C/C distance Fixing on around

(5x40) mm Solid MS Patti including cutting, welding and

fabrication etc; including one coat of primer of approved quality

and two coats of oil painting as per detail drawing etc. complete

as per directed Engineer in charge.

91 Providing erecting and fixing double coated Syntex PVC. (ISI) 15000.00 Litre 3.95

water tank of required capacity each with all necessary fittings

and connection etc. complete on terrace.

92 Providing laying and jointing in true line and level 50mm dia. 180.00 Rmt 195.67

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make as

approved by Engineer In Charge. Pipe shall be fixed on the wall

with the help of clamp at every two metre C/C or shall be

concelled as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

93 Providing laying and jointing in true line and level 40mm dia. 120.00 Rmt 148.12

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make as

approved by Engineer In Charge. Pipe shall be fixed on the wall

with the help of clamp at every two metre C/C or shall be

concelled as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

94 Providing laying and jointing in true line and level 25mm dia. 180.00 Rmt 91.84

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make as

approved by Engineer In Charge. Pipe shall be fixed on the wall

with the help of clamp at every two metre C/C or shall be

concelled as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

95 Providing laying and jointing in true line and level 15mm dia. 180.00 Rmt 72.65

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make as

approved by Engineer In Charge. Pipe shall be fixed on the wall

with the help of clamp at every two metre C/C or shall be

concelled as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Item Rate In

Description of Item Quantity Unit Amount

No figures

96 Providing, laying and jointing in true line and level 160 diametre 120.00 Rmt 831.22

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain

and other end socketed with rubber ring, & fittings conforming to

ISI 14735-1999 of approved make for drainage system pipe line,

pipe shall be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp of the size 160 mm

diametre x 210 mm length x 196 mm heigh at every 2000 mm

center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including

testing of pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

97 Providing laying (to level or slopes) and jointing reinforced 571.00 Rmt 665.48

concrete Light duty non-pressure pipes I.S. class NP2 of the

following internal diameter with collars and butt ends prepared

for collar joints including testing of joints complete.(D)

98 Providing, laying and jointing in true line and level 110 diametre 685.04 Rmt 836.73

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain

and other end socketed with rubber ring, & fittings conforming to

ISI 14735-1999 of approved make for drainage system pipe line,

pipe shall be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp of the size 110 mm

diametre x 149 mm length x 145 mm heigh at every 2000 mm

center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including

testing of pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

99 Providing, laying and jointing in true line and level 75 mm dia. 120.00 Rmt 292.90

UPVC SWRType B pipe conforming to IS 13592-1992 with one

end plain and other end socketed with rubbering and fitting

conforming to ISI 14735-1999 of approved make for drainage

system pipe line, pipe shall be jointed with each other with

rubber lubricant, pipe shall be fixed on wall using of PVC clamp at

every 2000 mm c/c or shall be conceled in walss as directed

including necessary fittings such as bends, shoes etc. including

testing of pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

100 Providing and fixing in PVC SWR cowel went 75mm dia to 4.00 No 15.66

pipes.(B) 75mm dia.

101 Providing and fixing in PVC SWR cowel went 110mm dia to 11.00 No 28.79

pipes.(B) 110mm dia.

102 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 42.00 No 571.08

mm diameter with jali of the following nominal diameter of self

cleansing design with C.I scread down or hinged grating including

the cost of cutting and making good the walls.

103 Providing and fixing wash down water closet (European type W C 18.00 No 2951.22

pan) with integral P and S trap including jointing the trap with

soil pipe in cement mortar 1:1 (1 cement five sand) including

providing and fixing plastic seat cover for wash down WC with CP

brass hinges and rubber buffers back plastic seat and including

providing and fixing PVC flushing tank with a pair of C I or MS

bracket with complete fitting such as lead valve siphon 15 mm dia

brass ball valve with polythene float CP brass handle unions and

couplings for connection with inlet out let and over flow pipes

mm dia porcelain enameled flush bend including cutting holes in

walls and making good the same connection the flush bend with

cistern and closet vitreous china.

Item Rate In

Description of Item Quantity Unit Amount

No figures

104 Provision and fixing water closet squatting orissa type W.C. pan 6.00 No 1607.92

size 580mm integral footrest and 100 mm P or S trap and in

cluding 25 mm dia CP brass flush valve and GI inlet connection

etc. comp. (A) Vitreous china long pattern white or color

105 Providing and fixing brass screw down stop tap.(A) 15mm dia. 24.00 No 205.83

106 Providing and fixing ball cock of approved. quality as directed.(A) 3.00 No 189.84

Copper Metal (ii) 50mm dia.

107 Providing and fixing washbasin with single hole for pillar tap with 18.00 No 1506.45

C.I. or M.S. brackets painted white including sutting holes and

making good the same but excluding fittings.(A) Vitreous

China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In

108 white colour.

Providing and fixing C.P. brass waste for washbasin or sink. (A) 18.00 No 67.91

109 Providing and fixing M.I. fisher union for washbasin or sink. (A) 18.00 No 78.75

110 Providing and fixing 600mm x 450mm bevelled edge mirrror of 18.00 No 833.73

superior glass mounted on 6mm thick A.C. sheet or plywood sheet

and fixing to wooden pluge with C.P. brass screws and washers.

111 Providing and fixing C.P. brass towel rail comlete with C.P. brass 18.00 No 603.19

brackets fixed to wooden plugs with C.P. brass scews (B) 600mm

x 20mm size.

112 Providing and fixing screw down bib taps of following size.(A) 54.00 No 214.81

Brass screw down bib tap polished bright. (i) 20mm dia.

113 Providing and fixing pillar tap, capstan head, screw down high 18.00 No 308.73

pressure with screws, shanks and back nuts. (i) 15mm dia.

114 Providing and fixing in position 300 mm high, 150 mm wide 360.00 No 707.00

English letters made from 1.0 mm thick stainless steel sheet as

directed by Engineer in charge with all necessary tools & plants

etc. complete.

115 Providing and fixing Urinal of approved quality including 12.00 No 1550.99

connection with trap and with integral longitudinal flush pipe.(A)

Squating plate pattern white earthenware 550mm x 300mm.

116 Providing and fixing Rubber plug for sink or wash basin. 12.00 No 17.15

117 Providing and fixing chromium plated brass half trun flush cock of 36.00 No 263.77

approved quality including fixing in pipe line etc. complete (ii)

118 Providing and fixing S.W. gully trap with C.I. grating brick 10.00 No 1246.92

masonry chamber and water tight C.I. cover with frame of 300mm

x 300mm size (inside) with standard weight (i) Square mouth

traps (B) 150mm x 100mm size P or R type

119 Constructing brick masonry chamber for underground C.I. 34.00 No 3172.41

Inspection chamber and bends with briocks having croshing

strength not less than 35Kg. Cm2 in C.M. 1:5 precast RCC cover

455mm x 610mm intenal dimensions with frame (R.C.C. top slabe

with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth with a

floating coat of neat cement on walls and bed concrete etc.

complete (i) Inside dimensions 455mmx 610mm and 450mm

deep for single pipe line.

Item Rate In

Description of Item Quantity Unit Amount

No figures

120 Constructing brick masonry chamber for underground C.I. 31.00 No 3883.45

Inspection C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5 precast RCC

cover 500mmx 700mm intenal dimensions with frame (R.C.C. top

slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth with a

floating coat of neat cement on walls and bed concrete etc.

complete (i) Inside dimensions 500mmx 700mm and 450mm

deep for single pipe line.

121 Extra over items for every additional depth of 0.1M. of part 18.00 Each 242.39

thereof beyond 450mm depth for Brick masonry chamber.(i) for

455mm x 610mm size.

122 Extra over items for every additional depth of 0.1M. of part 15.00 Each 264.86

thereof beyond 450mm depth for Brick masonry chamber.(i) for

500mm x 700mm size.

123 Providing cement vata (10cm x 10cm size) quarter round in 195.00 Rmt 23.68

cement mortar 1:1 including neat cement finishing watering etc.

124 Providing and fixing MS Ladder of required pattern with MS 300.00 Kg 113.12

flats(30x3mm) or round or square bars (12mm) at required

spacing & with round headed bolts and nuts or screws or welding

including primer coat of approved quality and two coats of oil

paintas as directed by engineer in charge

125 Providing and fixing in position 150 mm high, English letters 160.00 No 404.00

made from 1.0 mm thick stainless steel sheet as directed by

Engineer in charge with all necessary tools & plants etc. complete.

126 Providing and fixing polished 18 mm thick black granite with full 11.00 Sqmt 2719.93

round edge and double side polished of approved quality in

between urinal and fixing with cement slurry & adhesive

including moulding of both exposed edges as directed by

engineering in charge etc. complete.

127 Constructing Platform of 18 mm thick Polished Black Granite at 8.00 Sqmt 6235.74

top and 25 mm thick Kota stone slab one side polished at bottom

with cementing Materials / adhsives including makeing

necessary grooves in walls with Vertical sandwich two

Kotastone 25 mm support every 60 cm centre to centre or as

required including all labour material of approved quality incl.

full moulded round front edge granite strip of one side polished

and jointed with grey cement slurry including rubbing and

polishing etc. complete for all floors

128 provision and fixing of both side polished machine-cut marble 840.00 Sqmt 1616.00

stone shelves/partitions, ranging from 18mm to 20mm in

thickness, securely embedded into the wall through support fixing

using cement slurry and adhesive. The process encompasses the

necessary adjustments such as cutting the stone to fit as needed,

along with the meticulous smoothing of surfaces to achieve a

refined finish, inclusive of all requisite racking as per directed

engineer in-charge.

129 Providing & fixing in position glass partition with standard 171.00 Sqmt 2469.45

extruded colored anodized aluminum frame size 63mm x 38mm

x 2mm thick make vertical and horizontal grid distance as shown

in drawing with 12mm thick toughen glass directed with glass

film, fixed with transparent silicon rubber gasket in panel with

glazing clips 19 mm x 17.3mmx1.2mm in size including fixtures

and fastening with required all labour and equipment and

including rebar up to slab level in half partition and as per

detailed drawing as directed with all lead and lift.

Item Rate In

Description of Item Quantity Unit Amount

No figures

130 Providing & fixing in position glass panel with standard extruded 255.00 Sqmt 2712.86

colored anodized aluminum frame size 63mm x 38mm x 2mm

thick make vertical and horizontal grid distance as shown in

drawing with 12mm thick toughen glass directed with glass film,

fixed with transparent silicon rubber gasket in panel with

glazing clips 19 mm x 17.3mmx1.2mm in size including fixtures

and fastening with required all labour and equipment and

including rebar up to slab level in half partition and as per

detailed drawing as directed with all lead and lift. for FG

131 providing and fixing 12mm thick compact laminated panel door 11.00 Sqmt 8397.14

of merino or aproved equivalent mae with all accessories handle

and locing system including all fixtures and fastner and laboure

work etc completed as per engineer incharge.

132 Providing and laying and fixing 50 mm thick expansion joint by 166.00 Sqmt 1491.03

hydro cell semi rigid UV resistance with high performance

laminated closed cell polythene foam joint filler in sheet foam as

directed, etc. complete.

133 Applying and providing Expansion joint sealing System on 100 166.00 Sqmt 4772.00

mm vide joint including cleaning of exansion joint by mechanical

means provision of adhesive and flexible membrane with

required bond length as per menufracturer specification and

4mm thick alluminium strip covering with one side sloted and

bolted with suitable system, inclusive of all manpower, machinery

and material as per specification and as directed.

134 Providing and filling the expansion joint by Thioflex 600 polymer 166.00 Sqmt 515.39

or equivalent confirm to BS 4254-1983 as per required shade and

manufactured specifi-cation by making groove of 50 mm x

mm lather by cutting or by repairing groove and removing mortar

drop or any other foreign materials including applying primer

and filling required size (oversize of joint PU foam etc. complete.

135 Providing and fixing 25 cm Wide & 3mm thick exterior composite 111.00 Sqmt 1054.34

panel on existing expansion joint horizontally & vertically with all

material, hardware, acessories & fittings etc completed.

136 Providing & Fixing 114mm wide G.I. Sheets lovers having weight 83.00 Sqmt 7813.36

not less than 490 Gm/m roll formed to create 84mm wide louver

snap fixed on special shaped GI channel. Fix louvers & channels

shall finished with powder coating of 55 micron (1) 0.55mm thick

sheet.etc. complet as per detail drawing as directed.

137 Providing & fixing 25mm thick cupboards of plywood shutter 265.00 Sqmt 3297.65

including fixing 19 mm and 6mm thick back to back flush all proof

plywood & including with Teak Wood frame 40 mm x 25 mm size

as directed etc. complete including necessary both side

lamination 1 mm thick outer side & 0.80mm thick inner side fixing

by necessary SS hinges, handles, magnet, stoppers, etc. as directed

including fevicol, and other hardware material required. Plywood

and all fixture shall be of ISI quality and as approved by engineer-

in-charge including cost of teak wood beading, one coat of primer

and two coats of oil painting or polishing as directed.

138 Providing and fixing 0.45 meter wide Drinking platform 8.00 Sqmt 3038.08

including supplying and fixing granite stone of black or equivalant

quality 18 mm thick mirror polished on top and side posiition

and vertical strip at front with cement slurry & adhesive

including moulding of both exposed edges over 25 mm thick

kotah stone platform fixing in top and sides and itermediates

supports fixing with cement mortar and adhesive and finishing

all material and labour and assessories with necessary fitting

complete etc.

Item Rate In

Description of Item Quantity Unit Amount

No figures

139 Providing and fixing M.S Pipe fabrication For duct made from M.S 61.00 Sqmt 3868.30

pipe of 40 mm dia fitted into M.S Frame with clamp into

RCC/Brick structure at 0.10 m c/c at equal distance fixed

including all required accessories as per detailed drawing as

directed etc. complete. for All Floor

140 Providing and fixing coloured self adhesive PU-Tactile tile, ground 216.00 Sqmt 4791.44

surface indicators of Polyurethane) of size 300mm x 300mm for

guiding/warning to the visually visitors in the centre/side of the

pedestrian/approach pathway as per specification and guidelines

complete in all respect to the entire satisfaction of in charge.

141 Providing and fixing acrylic multilingual Braille (raised dots) 20.00 Nos 1765.48

DIRECTIONAL SIGNBOARDS of size 225 x 150mm designed as

per accessibility standards and having 3.5mm thick acrylic base

plate with Upper Case San Serif words made of white acrylic non

glare cut out letters of height 15mm raised not less than 0.8mm

above base plate and the equivalent word written in Hindi with

Devanagari non glare acrylic letters of height 15mm raised not

less than 0.8mm above base plate and having a non-glare acrylic

cut arrow pointing in the required direction. Each signboard to be

fixed as per manufacturers specifications on the wall at the

approved location and at a height of 1200mm from FFL complete

as per design / specifications and guidelines as per the entire

satisfaction of the Engineer-in-charge

142 Providing & Fixing Braile Indicator Of Size 170 Mm X 35mm For 150.00 Rmt 946.37

Handrails Of The Approved Design And Make Have Braile Dots

Raised 0.5 Mm Above Base Plate To Be Installed At Specific

Locations As Per Direction Of Engineer In Charge

143 Providing and fixing of conspectus tape 50mm width on of treads 30.00 Rmt 304.01

in staircase including cutting pasting etc. As per harmonised

guidelines complete in all respect to the entire satisfaction of

engineer in charge.

144 Providing and Fixing a set of wall mounted 38 mm dia U shaped 6.00 Set 2730.03

horizontal stainless steel collapsible grab bar , 38mm vertical

stainless steel fixed grab rail of grade SS 304 from round pipe

supported and 75 mm dia 8 mm thick SS 304 base flange on wall

including anchor fasteners, nuts, accessories as per detailed

drawing etc. complete as directed by Architect or Engineer in

145 Providing and fixing EURONICS 304 Stainless Steel Handicap Grab 12.00 Nos 3368.35

Bar, Size 600 millimeter, including all necessary fittings and

fixtures, complete as per the direction of the Engineer-in-charge.

146 Excavation for foundation for depth from 3.0 m to 5.0 m including 83.00 Cumt 175.97

sorting out and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead.(B) Dense or Hard soil

147 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size 2.00 Nos 958.17

having weight not less than 35Kg.

148 Providing & erecting open well horizontal mono block pump set 2.00 Nos 36107.50

with cast iron body, complete for three phase submersible motor

having [H]For 15 H.P,3 phase open well horizontal mono block

pump set suitable for 1600 LPM to 1025 LPM @ 33 to 42 MTR

head suitable for 65/80 mm dia delivery pipe

Item Rate In

Description of Item Quantity Unit Amount

No figures

149 Supplying & erecting approvedmake 3 phase motor control 3.00 Nos 19695.00

cubicalpanel (Star-Delta) made from 16G.CRCA sheet duty

painted with epoxy powder painted inside and outside with

hinged doors and locking arrangement, consisting suitable size of

ON-OFF isolator (AC- 3/23duty) main fuses,single phasing

preventer cum water level, Guard(Compe unit), Toggle switch to

by pass Single phase preventercum WLG,indicating lamps forR-Y-

Bphases, over load relay.Automatic water level controller,

incoming wires duty socket Crimped,Panel to be erected on angle

iron frame grouted on wall as overload relay,thermal/Electronics

star delta cutoff timer,start-stop push buttons.The isolator

overload relay &cntractors ofL&T,Siemens or Cuttler Hamer make

only.Panel to be erected on angle iron frame ground on wall

(e)S/D upto

150 Providing 2.5fixing

and H.P. rolling shutters of approved make made of 10.00 Sqmt 3503.41

80 mm wide M.S laths inter-locked together through heir entire

length and jointed together at the ends by end locks mounted on

specially designed pipe shaft with bracket plates,guide channels

and arrangement for inside and outside locking with push-pull

operation including the cost of hood cover and sprig

etc.complete(A) Shutters having width below 3.5M

151 Constructing brick masonry chamber for underground C.I. 20.00 No. 7180.44

Inspection chamber and bends with briocks having croshing

strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame

(Light duty) 455mm x 610mm intenal dimensions, total weight of

cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.)

and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-

cement :2- coarse sand :4-graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick with

cement mortar 1:3 finished smooth with a floating coat of neat

cement on walls and bed concrete etc. complete.(iii) Inside

dimensions 600mm x 850 mm and 450mm deep for pipe lines

152 with threeand

Providing or more inlets.

laying (two level or slopes) and jointing with stiff 240.00 Rmt. 696.46

mixture of Cement Mortar in proportion 1:1, Salt glazed stone

ware pipes of pipes 150mm laying lime concrete 1:2:4 (1-Lime

putty :2-Fine samd : 4-Graded brick aggregates 40mm nominal

size) bedding for stoneware pipes of following internal diameters

with necessary formwork and curing complete.

153 Box cutting the road surface to proper slope and camber for 1555.00 Cum. 104.04

making a base for road work including removing the excavated

stuff and depositing on the road side slope as directed upto

50Mt.lead.

154 Filling in plinth with sand under floors including watering 519.00 Cum. 532.27

ramming, consolidating and dressing complete

155 Construction of granular sub-base 150 mm thick by providing 389.00 Cum. 1241.29

coarse graded machine crushed B.T. material satisfying MOST

specification of grading I (B.T. stone aggregate 53 mm to 26.5 mm

35 %, 26.5 to 4.75 mm - 45 % and 2.36 mm below - 20 %

)including spreading in uniform layer with motor grader on

prepared surface, mixing by mix in place method with rotavator

at OMC and compacting with vibratory roller to achieve the

desired density etc. complete.

156 Providing and laying wet mix macadam base course 250 mm thick 648.00 Cum. 1262.50

using machine crushed B.T. chips as per required gradation

mixing with required optimum quantity of water, conveying the

mix to site of work, spreading in to grade and camber with

mechanical paver and consolidation each layer with vibratory

roller including cost of material labour plant and equipment etc.

Item Rate In

Description of Item Quantity Unit Amount

No figures

157 Compaction and finishing of cement concrete road by trimix 2468.00 Sqm. 63.63

M.250 process providing extra Labour charges for the trimix

vacume dewatering service process on cement concrete road

sutface by using vacuum dewatering pump floater surface

vibrator including making groves and rough finish to surface

including leveling etc complete.

158 Providing and fixing pre-cast Rubber Dye / steel Dye inter locking 1608.00 Sqm 686.90

concrete block 60mm thick with grade of concrete M300

pnumatic compressed / vibrated mechanically and as per

approved design Confirming to IS 15658 : 2006 including 35 mm

Sand layer for levelling and filling the joint with sand in proper

line and level as per guidlines of IRC : SP 63-2018 etc. Complete.

159 Providing and fixing pre-cast concrete kerb stone of gray cement 832.00 Rmt. 361.64

based concrete block 30cm length,30cm height and 15cm thick of

M250 grade concret as per approved design and including

excavation for fixing in proper line and level,filling the joint with

C:M 1:3 (1cement:3fine sand) etc complete.

160 Drilling of min. 250 mm dia. bore hole in all strata including 310.00 Rmt 1270.58

dualover burden strata by combination DR/DTH rig including

lowering 200 mm dia MS ERW pipes in bore hole and testing

etc.all work as per directed engineer incharge.

161 Manufacture, supply and delivery of cage typeTrapezoidal shape ( 200.00 Rmt 1682.66

' V ') wire wound low carbon, Galvanized screen pipe and

Stainless Steel Screen pipes, confirming IS: 8110 For (B) 200mm

dia 1) 1.00mm Slot size

162 Bore plug having 100 mm height made from M.S. plate with 3 2.00 No 1161.62

holes at equal distance on circumference for nut-bolts type,

locking arrangement with nuts-bolts & lock nuts of std. Make

complete. For 250mm dia

163 Providing PVC insulated flat submersible cable as per detailed 400.00 Rmt 180.79

technical specifications of R/C of GWSSB conforming to IS

IEC 60227 / 60228.d)1 R x 3 C x 6.0 mm2

164 Suppling and installing 3 Phase Borewell 15.00 HP Submersible 2.00 No 37160.93

Pump Sets Electric motor driven conforming to I.S. 8034 and

motor conforms to IS-9283 working at 3 phase 400/440 volt

C/S A.C. supply & 2900 R.P.M. cat

165 Providing and fixing check or non return pully wheel valve of 50 4.00 No 1111.00

mm diameter.

166 Providing and fixing to wall,ceiliing and floor galvanised mild 300.00 Rmt 787.40

steel tubes ( Medium grade ) of the following nominal bore, tube,

fittings and clamps included making good the wall, ceilling and

floor (F) 50 mm

167 Supplying and lowering ISI-mark edunplasticized PVC (uPVC) 80.00 Rmt 393.90

casing pipe,200 mm outer diameter,as per IS:12818

169 Geohydrological ground water investigation including vehicle 2.00 Nos 14428.86

charges for three phase DTH bore/DR tube well including water

sample testing & chemical analysis

170 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 240.00 Rmt 336.24

working pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type

fittings, wall clipsetc. including making good the wall ceiling and

floor.(G)110 mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

171 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 260.00 Rmt 696.90

working pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type

fittings, wall clipsetc. including making good the wall ceiling and

floor.(G)160 mm

172 Providing junction for rain water juncton chamber of size 26.00 Nos. 8981.93

0.60x0.60x0.75m with excavation of size 1.96x1.96 m & 0.15m

thick c.c.1:2:4 bed concrete including brick masonary wall in CM

1:6 of 0.75m height & 0.23m thick with 15mm thick cement

plaster inside & outside & 1.06x1.06 RCC (1:2:4) slab of thickness

0.15m with CRS steel and 0.60mx0.45m cast iron manhole cover

with frame weight not less than 35 kg as per directed by Engineer-

173 Providing Filter chamber of Brick work in C:M 1:6 of size 8.00 Nos. 15287.36

2.06mx1.20m x1.20m & excavation dimension of 2.66mx

1.81x1.35m including C.C 1:2:4 bed concrete of 0.15m thick

including brick work in c.m 1:6 for 23cm thick wall including

15mm thick cement plaster inside & outside with cement slurry &

10cm thick RCC 1:2:4 top cover with frame of minimum weight of

35 kg & filling filter material kapchi in layers (25-40mm & 10-

20mm) & BT metal 40mm & sand as per directed by Engineer-in-

174 Providing Recharging pit of size 2.0m Dia.& 2.0m depth of water 3.00 Nos. 8209.28

logging with excavation filling the pit with gravel & sand in layers

including making 300mm dia bore depth of 4.5mt & above

concrete with kapchi in layers (25-40mm & 10-20mm) & BT

metal 40mm & filling brick as directed by Engineer-in-charge.

175 Providing and laying controlled cement concrete M-250 and 1287.10 Cumt 5943.85

curing complete including the cost of form work but excluding the

cost of reinforcement for reinforced concrete work in Retaning

176 Providing and filter media 600mm thick as directed at the back of 390.03 Sqmt 1248.74

Protection Wall as per detailed specification.

177 Constructing providing and fabricating cattle guard using channel 15.00 Sqmt 5071.21

section frame of size ISMC series 100 mm x 50 mm (Weight

kg/Rmt) and ISMC section 100 mm x 75mm (weight

kg/Rmt) intermediate support for welding G.I.pipe at 12 Cm C/C

of size 50 mm in a frame made of Channel section size 100 mm x

50 mm all round including fixing the unit on prepared chamber of

masonary wall using MS hold fast embeded in masonary wall top

as directed by Engineer in charge and as per drawing and

necessary required arrangement etc complete.

178 Providing and fixing decorative entrance gate made out of cast 1658.00 kg 165.64

iron and various mild steel tabular section combination , the

Ornamental entrance gate should be fixed at compound wall

including pattern and die making , cutting , welding , grinding,

fabrication , fixing in position at compound wall with necessary

pedestal, bearing block and other locking arrangement. The

entrance gate should be painted with two coats of priming coat of

paint, and two coat of oil paint etc complete. As per detail design

and instruction of architect.

Item Rate In

Description of Item Quantity Unit Amount

No figures

179 Providing and fixing concertina coil fencing with punched tape 768.00 Rmt 590.85

concertina coil 600 mm dia 10 mt openable length having 50 no

rounds per 6 mt length, upto 3mt height of wall with existing

angle iron (50mm x50mm x5mm )requird shaped As per Directed

Engeenier in charge. placed 2.4mt or 3.00mt apart and with

horizontal R.B.T. reinforced barbed wire(3 mm) , stud tied with

G.I. staples and G.I. clips to retain horizontal, including necessary

bolts or G.I.barbed wire tied to angle iron, all complete as per

direction of Engineer-in-charge, with reinforced barbed tape

(R.B.T.)/Spring core (2.5 mm thick) and weight 43.478 gm/meter

at compound wall for ESR M4/ intakewell.

180 Steel work, welded in built up sections framed work including 21840.00 kg 90.48

cutting, hoisting, fixing in position and applying a priming coat of

read lead paint & two coat oil paint. (A)In beams and joists,

channels angles Tees, flats, with connecting plates or angle cleats

as in main and cross beams. Hip and jack rafters, purlins conneted

to common rafters and the like..

181 Providing and fixing of Ridge flashing for roof panel shall be made 780.00 Sqm 858.67

out of 0.5 mm thick pre coated GI sheet . The Precoated sheet shall

be of minimum 240 mpa steel grade confirming to IS 14246:1995

and shall have zinc coating of minimum 120 gsm as per

IS:277:1992 , 5-7 microns epoxy primer on both side of the sheet

and polyester top coat 15-18 micron. The PPGI Sheet shall have

plastic protective guard film of minimum 25 microns to avoid

scratches during transportation. The ridge shall be fixed to the

steel members by pop rivet or self drilling/self stitching fastners

@ maximum 450 mm c/c along length of capping/flashing etc

complete .

182 Earth work for Embankment including breaking clods,dress 98764.32 Cum 161.22

ing,with all lead and lift.( excluding watering and

consolidation)(E) From borrow pits within 3 km lead.

183 Rolling of Earth work in layers with power roller including filling 98764.32 Cum 22.63

in depressions which occure during the process.

184 Supply. installation, testing & commissioning of ISI approved 1.00 No 98432.21

electrical motor driven jockey pump set having 10.8 m3/hr. @

70m head. The pump unit shall be a horizontally direct mounted

motor. Unit shall comprise the following minimum requirements:

a) Pump, b) Electric motor IE2, c) Foundation bolts, d) Mating

flanges with gasket and fasteners, e) Discharge gauges, etc.

complete in all respect, with labour.

185 Supply, installation, testing & commissioning of Priming tank, 1.00 No 25677.97

HDPE type, 1000 litres, with necessary piping 100 mm size, G.I

pipe for priming the pumps, pipe of with butterfly valves for

isolation, Water Filling to priming tank by piping min. 50 mm size,

with all complete.

186 Supply, installation, testing & commissioning of Manifold( surge 1.00 No 55635.60

vessel,)for fire hydrant system, min. 300 mm diameter, made

from M.S plate, hydro tested to 15 kg./cm2. with ball valves,

header with couplings for fitting pressure switches, pressure

gauges etc.with necessary isolation valves with all complete.

Item Rate In

Description of Item Quantity Unit Amount

No figures

187 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW 20.00 Mtr 398.01

piping, conforming to IS:1239, part-I, Heavy class up to 150 mm

dia. and IS:3589, for size 200 mm dia. & above, thickness. G.I. pipe

fitting's as per IS: 1239, part-II, Heavy class for size 150 mm dia. &

below & IS: 3589, for size 200 mm dia. above, flanges, nuts bolts &

washers, 3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system pressure,

hook-up etc.

Painting for piping, fittings & structural pipe support, shall be

two coat of zinc primer and two coats of fire red conf. to IS:

Shade 536. Complete with all accessories as per approved

drawings, specicification and direction of the Engineer-in-Charge,

with all complete. 25 mm dia.

188 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW 30.00 Mtr 641.95

piping, conforming to IS:1239, part-I, Heavy class up to 150 mm

dia. and IS:3589, for size 200 mm dia. & above, thickness. G.I. pipe

fitting's as per IS: 1239, part-II, Heavy class for size 150 mm dia. &

below & IS: 3589, for size 200 mm dia. above, flanges, nuts bolts &

washers, 3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system pressure,

hook-up etc.

Painting for piping, fittings & structural pipe support, shall be

two coat of zinc primer and two coats of fire red conf. to IS:

Shade 536. Complete with all accessories as per approved

drawings, specicification and direction of the Engineer-in-Charge,

with all complete. 50 mm dia.

189 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW 36.00 Mtr 1176.90

piping, conforming to IS:1239, part-I, Heavy class up to 150 mm

dia. and IS:3589, for size 200 mm dia. & above, thickness. G.I. pipe

fitting's as per IS: 1239, part-II, Heavy class for size 150 mm dia. &

below & IS: 3589, for size 200 mm dia. above, flanges, nuts bolts &

washers, 3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system pressure,

hook-up etc.

Painting for piping, fittings & structural pipe support, shall be

two coat of zinc primer and two coats of fire red conf. to IS:

Shade 536. Complete with all accessories as per approved

drawings, specicification and direction of the Engineer-in-Charge,

with all complete. 80 mm dia.

190 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW 260.00 Mtr 1690.47

piping, conforming to IS:1239, part-I, Heavy class up to 150 mm

dia. and IS:3589, for size 200 mm dia. & above, thickness. G.I. pipe

fitting's as per IS: 1239, part-II, Heavy class for size 150 mm dia. &

below & IS: 3589, for size 200 mm dia. above, flanges, nuts bolts &

washers, 3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system pressure,

hook-up etc.

Painting for piping, fittings & structural pipe support, shall be

two coat of zinc primer and two coats of fire red conf. to IS:

Shade 536. Complete with all accessories as per approved

drawings, specicification and direction of the Engineer-in-Charge,

with all complete. 100 mm dia.

Item Rate In

Description of Item Quantity Unit Amount

No figures

191 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW 20.00 Mtr 2525.00

piping, conforming to IS:1239, part-I, Heavy class up to 150 mm

dia. and IS:3589, for size 200 mm dia. & above, thickness. G.I. pipe

fitting's as per IS: 1239, part-II, Heavy class for size 150 mm dia. &

below & IS: 3589, for size 200 mm dia. above, flanges, nuts bolts &

washers, 3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system pressure,

hook-up etc.

Painting for piping, fittings & structural pipe support, shall be

two coat of zinc primer and two coats of fire red conf. to IS:

Shade 536. Complete with all accessories as per approved

drawings, specicification and direction of the Engineer-in-Charge,

with all complete. 150 mm dia.

192 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW 7.00 Mtr 3423.73

piping, conforming to IS:1239, part-I, Heavy class up to 150 mm

dia. and IS:3589, for size 200 mm dia. & above, thickness. G.I. pipe

fitting's as per IS: 1239, part-II, Heavy class for size 150 mm dia. &

below & IS: 3589, for size 200 mm dia. above, flanges, nuts bolts &

washers, 3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system pressure,

hook-up etc.

Painting for piping, fittings & structural pipe support, shall be

two coat of zinc primer and two coats of fire red conf. to IS:

Shade 536. Complete with all accessories as per approved

drawings, specicification and direction of the Engineer-in-Charge,

with all complete. 200 mm dia.

193 Supply, installtion, testing & commissioing of Underground GI 20.00 Mtr 2020.00

(ERW) piping conforming to IS:1239, part-I, Heavy class ('C' class)

up to 150 mm dia. and IS:3589 Heavy class ('C' class), for 200 mm

dia. & above, min. 6.35mm thickness including Heavy class

fittings, anti-corrosive tape of size 150 mm wide x 4 mm thick,

wrapping & coating with 13KV holiday testing . Rates shall

include sand bedding of 75mm dia all around, backfilling of the

excavated including installation of heavy pipe fitting's, flanges,

etc. 10 % of all the welded joints shall be done radiographically

tested and 50% of the joints radiographed shall be the "Field

Joints". Hydrostatic testing for 2 hours at 150% of the system

pressure, hook-up etc., complete with all accessories as per

approved drawings, specicification and direction of the Engineer-

in-Charge, with all complete. (Road Crossing) 100 mm dia.

194 Supply, installtion, testing & commissioing of Underground GI 25.00 Mtr 3047.12

(ERW) piping conforming to IS:1239, part-I, Heavy class ('C' class)

up to 150 mm dia. and IS:3589 Heavy class ('C' class), for 200 mm

dia. & above, min. 6.35mm thickness including Heavy class

fittings, anti-corrosive tape of size 150 mm wide x 4 mm thick,

wrapping & coating with 13KV holiday testing . Rates shall

include sand bedding of 75mm dia all around, backfilling of the

excavated including installation of heavy pipe fitting's, flanges,

etc. 10 % of all the welded joints shall be done radiographically

tested and 50% of the joints radiographed shall be the "Field

Joints". Hydrostatic testing for 2 hours at 150% of the system

pressure, hook-up etc., complete with all accessories as per

approved drawings, specicification and direction of the Engineer-

in-Charge, with all complete. (Road Crossing) 150 mm dia.

Item Rate In

Description of Item Quantity Unit Amount

No figures

195 Design , Supply and installation of Safety Signage made of Zinc 5600.00 Sq. inch 9.41

Sulphilde based glow in dark , Rigid sheet with High Luminous

property enclosed in a transperent weather proof UV stabilized

plastic pasted on 3 mm thick clear acrylic sheet such as EXITS,

EMERGENCY EXIT, DO NOT USE LIFT DURING FIRE, FLOOR

MARKINGS, FIRE LIFT, STAIRCASE EXIT, FIRE ALARM CALL

POINT, FIRE HOSE REEL, FIRE HYDRANT POINT etc.

196 Supply, installation, testing & commissioning of pressure switch. 3.00 No 2824.58

(Range 0 to 16 kg/cm2)

197 Supply, installation, testing & commissioning of 150 mm dia. dial 6.00 No 2738.99

Burdon Type Glycerine Filled pressure gauge with isolation ball

valve arrangements with necessary isolation valves with all

complete.( Range 0 to 15 kg/cm2)

198 Supply, installation, testing & commissioning of Cast iron body 2.00 No 5905.93

double flanged gate valve With Rising Spinldle conf. to IS:

PN-1.6 with mating flanges, drilling as per IS/ANSI 150# with

mating flanges, galvanized nut, bolts & washers, gasket 3 mm

thick, etc., with all complete. 50 mm dia.

199 Supply, installation, testing & commissioning of Cast iron body 1.00 No 8182.71

double flanged gate valve With Rising Spinldle conf. to IS:

PN-1.6 with mating flanges, drilling as per IS/ANSI 150# with

mating flanges, galvanized nut, bolts & washers, gasket 3 mm

thick, etc., with all complete. 80 mm dia.

200 Supply, installation, testing & commissioning of Cast iron body 2.00 No 10271.18

double flanged gate valve With Rising Spinldle conf. to IS:

PN-1.6 with mating flanges, drilling as per IS/ANSI 150# with

mating flanges, galvanized nut, bolts & washers, gasket 3 mm

thick, etc., with all complete. 100 mm dia.

201 Supply, installation, testing & commissioning of Cast iron body 1.00 No 15920.34

double flanged gate valve With Rising Spinldle conf. to IS:

PN-1.6 with mating flanges, drilling as per IS/ANSI 150# with

mating flanges, galvanized nut, bolts & washers, gasket 3 mm

thick, etc., with all complete. 150 mm dia.

202 Supply, Installation, Testing & Commissioning of Cast iron body 5.00 No 2011.45

Butterfly valve according to IS: 13095, PN-1.6, Iron Disc for size

150 mm dia. & below Lever operated and above 150 mm dia. Gear

operated complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc., with all

complete. 50 mm dia.

203 Supply, Installation, Testing & Commissioning of Cast iron body 1.00 No 2567.79

Butterfly valve according to IS: 13095, PN-1.6, Iron Disc for size

150 mm dia. & below Lever operated and above 150 mm dia. Gear

operated complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc., with all

complete. 80 mm dia.

204 Supply, Installation, Testing & Commissioning of Cast iron body 4.00 No 3124.15

Butterfly valve according to IS: 13095, PN-1.6, Iron Disc for size

150 mm dia. & below Lever operated and above 150 mm dia. Gear

operated complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc., with all

complete. 100 mm dia.

205 Supply, Installation, Testing & Commissioning of Cast iron body 2.00 No 4493.65

Butterfly valve according to IS: 13095, PN-1.6, Iron Disc for size

150 mm dia. & below Lever operated and above 150 mm dia. Gear

operated complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc., with all

complete. 150 mm dia.

Item Rate In

Description of Item Quantity Unit Amount

No figures

206 Supply, installation, testing & commissioning of Cast iron body 1.00 No 1540.67

Dual Plate Wafer Type NRV conf. to IS: 210, PN-1.6 complete with

mating Flanges class # 150 with bolts & nuts, washers, gaskets

mm thick, etc., with all complete Accessories 50 mm dia.

207 Supply, installation, testing & commissioning of Cast iron body 1.00 No 2225.42

Dual Plate Wafer Type NRV conf. to IS: 210, PN-1.6 complete with

mating Flanges class # 150 with bolts & nuts, washers, gaskets

mm thick, etc., with all complete Accessories 80 mm dia.

208 Supply, installation, testing & commissioning of Cast iron body 2.00 No 3166.96

Dual Plate Wafer Type NRV conf. to IS: 210, PN-1.6 complete with

mating Flanges class # 150 with bolts & nuts, washers, gaskets

mm thick, etc., with all complete Accessories 100 mm dia.

209 Supply, installation, testing & commissioning of Cast iron body 1.00 No 5820.34

Dual Plate Wafer Type NRV conf. to IS: 210, PN-1.6 complete with

mating Flanges class # 150 with bolts & nuts, washers, gaskets

mm thick, etc., with all complete Accessories 150 mm dia.

210 Supply, installation, testing & commissioning of SG iron body 1.00 No 1112.71

SinglePlate Wafer Type NRV conf. to ASTMA 536, PN-1.6 complete

with mating Flanges class # 150 with bolts & nuts, washers,

gaskets 3 mm thick, etc., with all complete. Accessories 50 mm dia.

211 Supply, installation, testing & commissioning of SG iron body 1.00 No 1455.09

SinglePlate Wafer Type NRV conf. to ASTMA 536, PN-1.6 complete

with mating Flanges class # 150 with bolts & nuts, washers,

gaskets 3 mm thick, etc., with all complete. Accessories 80 mm dia.

212 Supply, installation, testing & commissioning of SG iron body 1.00 No 1797.46

SinglePlate Wafer Type NRV conf. to ASTMA 536, PN-1.6 complete

with mating Flanges class # 150 with bolts & nuts, washers,

gaskets 3 mm thick, etc., with all complete. Accessories 100 mm

213 Supply, installation, testing & commissioning of Y Type Strainer 1.00 No 5563.55

complete with mating flanges with bolts & nuts, washers, gaskets

3 mm thick, etc., with all complete accessories. 80 mm dia.

214 Supply, installation, testing & commissioning of Y Type Strainer 1.00 No 7275.42

complete with mating flanges with bolts & nuts, washers, gaskets

3 mm thick, etc., with all complete accessories. 100 mm dia.

215 Supply, installation, testing & commissioning of Y Type Strainer 2.00 No 11555.09

complete with mating flanges with bolts & nuts, washers, gaskets

3 mm thick, etc., with all complete accessories. 150 mm dia.

216 Supply, installing, testing and commissioning of Normax make CI 1.00 No 4194.07

heavy duty ball type foot valve with flanges, nut bolts, gaskets etc.

with necessary complete accessories. 80 mm dia.

217 Supply, installing, testing and commissioning of Normax make CI 2.00 No 6162.72

heavy duty ball type foot valve with flanges, nut bolts, gaskets etc.

with necessary complete accessories. 100 mm dia.

218 Supply, installing, testing and commissioning of Normax make CI 1.00 No 12411.02

heavy duty ball type foot valve with flanges, nut bolts, gaskets etc.

with necessary complete accessories. 150 mm dia.

219 Supply, installation, testing & commissioning of Four way fire 1.00 No 8987.29

brigade Inlet connection with 63 mm dia. stainless steel (SS304)

instantaneous male inlets with built in non return valve in each

inlet with 150 mm dia. header pipe, suitable rubber cap and GI

chain including nuts, bolts, washers, gasket 3 mm thick, etc. with

all complete.

Item Rate In

Description of Item Quantity Unit Amount

No figures

220 Supply, installation, testing & commissioning of Two way fire 2.00 No 5135.60

brigade Inlet connection with 63 mm dia. stainless steel (SS304)

instantaneous male inlets with built in non return valve in each

inlet with 100 mm dia. header pipe, suitable rubber cap and GI

chain including nuts, bolts, washers, gasket 3 mm thick, etc. with

all complete.

221 Supplying FIRE bucket round bottom of 9 liters capacity made out 8.00 No 1027.12

of 24 gauge G.I Sheet with extra handle at bottom duly painted

white inside and Red out side with FIRE mark. Filled with dry-

sand and kept on existing stand provided or hung on wall hook.

222 Supplying and erecting floor mounting Stand for keeping four nos. 2.00 No 5563.56

of FIRE buckets comprising 1500 mm in length, 900 mm height

frame made out of 30mm x 30 mm x 4 mm angle iron with cross

supports legs, welded with 4 hooks and duly painted with one

coat of primer and two coats of approved enamel P O red paint.

223 Supply & installation of stainless steel body Orifice Plate of 12.00 No 1069.91

suitable inner bore along with matching flange - as per

specification & requirement as per hydraulic calculation.

224 Providing and fixing approved make Perforated C type cable tray. 10.00 Mtr 471.67

Made from pre- galvanized sheet steel. The cable tray should be

bended as per IS 2062/1079 . with max 17.5% perforation with

coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and

as per instruction of engineer in charge..(5) 300 X 50 X 1.5 mm

225 Providing and fixing approved make Perforated C type cable tray. 10.00 Mtr 322.19

Made from pre- galvanized sheet steel. The cable tray should be

bended as per IS 2062/1079 . with max 17.5% perforation with

coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and

as per instruction of engineer in charge..(3) 150 X 50 X 1.5 mm

226 Supply, installation, testing & commissioning of Oblique pattern 12.00 No 5435.17

type stainless steel (SS 304) single headed External Fire Hydrant

Valve with 63 mm dia. female instantaneous outlet conf. to IS:

5290, type - A, including mating flanges, galvanised nuts,

galvanised bolts/studs, washers & gaskets 3 mm thick with all

227 Supply, installation, testing & commissioning of 63 mm dia. 12.00 No 1754.66

stainless steel (SS 304) Universal Branch Pipe conf. to IS:

228 Supply & installation, testing & commissioing of Fire Fighting 12.00 No 6967.29

Hose - conf. to IS : 636, type B (type- 3), The fire hose shall be

m long with 63 mm dia. stainless steel (SS 304) couplings conf. to

IS: 903, at both the ends for connection with the hydrant valve

and the branch pipe.

229 Supply, installation, testing & commissioning of fabricated from 3 12.00 No 2525.00

mm MS sheet, hose box of size-450 mm x 600 mm x 250 mm -

painted with Fire Red as per IS: 5, shade no. 536 front 3 mm thick

transparent glass with lock & key, handle and brass hinges - to

accommodate one number of 15 mtr long hose and one number of

universal branch pipe, including supporting arrangement with

civil work.

230 Supply, Installation, testing & commissioing of Swinging type mild 12.00 No 7403.82

steel hose reel drum with 20 mm dia. x 30 mtr. rubber hose as per

IS: 884. The mounting stand shall be of mild steel and the hose

shall be fitted with a SS shut-off nozzle & SS ball valve of 25 mm

dia. including supporting arrangement with all complete.

accessories

Item Rate In

Description of Item Quantity Unit Amount

No figures

231 Supplying, fixing & testing of of CI ball Valve 25mm dia. (Thread) 23.00 No 706.14

232 Supplying, fixing & testing of New Battery of diesel engine 150 1.00 No 15834.75

233 Supply and installation of Diesel Tank For Diesel Engine With All 1.00 No 16690.67

Accessories 100 Ltrs.

234 Supplying, filling & testing lube oil for diesel engine 20.00 Ltrs 320.98

235 Supply and commissioning of Oil Filter. 1.00 No 706.14

236 Supplying, filling of diesel in diesel engine tank 75.00 Ltrs 89.87

237 Supply and commissioning of Diesel Filter 1.00 No 427.97

238 Supplying, filling & testing coolant to engine cooling for radiator 20.00 Ltrs 239.66

239 Filling Of Gaps Between pipe and Core Cutting Hole With 59.00 No 299.58

Chemical and Cement

240 Steel work, welded in built up sections framed work including 270.00 Kg 90.48

cutting, hoisting, fixing in position and applying a priming coat of

read lead paint & two coat oil paint. (A)In beams and joists,

channels angles Tees, flats, with connecting plates or angle cleats

as in main and cross beams. Hip and jack rafters, purlins conneted

to common rafters and the like.

241 Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper 15.00 Mtr 136.35

cable 1.1 KV grade to be erected as directed of following size. (E)

3 core 2.5 Sq. mm for pressure switch

242 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 20.00 Mtr 285.83

multistrand Copper conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe at road crossing or

floor of following size of cable. (Only Fire Panel to Fire Pump) (B)

3 core 4 Sq. mm

243 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 30.00 Mtr 497.93

multistrand Copper conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe at road crossing or

floor of following size of cable. (Only Fire Panel to Fire Pump) (D)

3 core 10 Sq. mm (Only Fire Panel to Fire Pump)

244 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 30.00 Mtr 213.11

multistrand Copper conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe at road crossing or

floor of following size of cable for Diesel Engine Battery Charger

(A) 3 core 2.5Sq. mm

245 Supply, Filling and Fixing of approved make ABC type fire 17.00 No 1968.64

extinguisher - 6 Kg. Capacity as per IS:15683 & IS :

246 Supply, Filling and Fixing of approved make CO2 type fire 17.00 No 5520.76

extinguisher. Capacity 4.5 Kg. (conforming to IS-15683).

247 Supply, Filling and Fixing of approved make ABC Moduler type 3.00 No 3423.73

automatic fire extinguisher. Capacity 5 Kg. (conforming to IS-

248 Submitting the application to obtain Fire Plan Approval and After 1.00 No 151500.00

Completion of Work Obtain Final Fire NOC for 3 Year.

249 Supply, Installation and commissioning of Air Release Valve, 25 2.00 No 1412.29

mm Dia. connection.

250 Supply, Installation and commissioning of Fire Alarm Panel 2.00 No 22725.00

Conventional type, 4 zone, with complete accessories.

251 Supply, Installation and commissioning of smoke detectors / heat 15.00 No 1027.12

detectors, with complete accessories.

252 Supply, Installation and commissioning of plug in base for the 15.00 No 256.78

smoke detectors, hooters, with complete accessories.

253 Supply, Installation and commissioning of Audio hooters , with 12.00 No 1069.91

complete accessories.

254 Supply, Installation and commissioning of Manual Call Points, 12.00 No 1010.00

with complete accessories.

Item Rate In

Description of Item Quantity Unit Amount

No figures

255 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 650.00 Mtr 176.75

multistrand Copper conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of

cables (A) 2 core 2.5 Sq. mm for Fire Alarm System

256 Core cutting in wall and in RCC slab with size as below: 50 mm 34.00 No 342.37

257 Core cutting in wall and in RCC slab with size as below: 80 mm 5.00 No 427.97

258 Core cutting in wall and in RCC slab with size as below: 100 mm 4.00 No 513.56

259 Core cutting in wall and in RCC slab with size as below: 150 mm 10.00 No 599.15

260 Core cutting in wall and in RCC slab with size as below: 200 mm 6.00 No 855.93

261 Supply, installation, testing & commissioning of ISI approved 1.00 Set 186850.00

electrical motor operated Kirloskar make fire hydrant main

pump set horizontal end suction back pull out top discharge

centrifugal fire pump set with all the standard acessories, base

frame, coupling, and foundation bolts with following

specifications: Model -DB 80/26, Flow-96 m3/hr, Head-70

meter, Motor Rating -30KW/40HP/3 ph, Suc x Del - 80 x

262 Supplying, Installation, Testing and commissioning of Kirloskar 1.00 Set 419150.00

make diesel engine driven fire hydrant pump set suitable for

automatic operation and consisting of following: horizontal type,

centrifugal end suction back pull out, top discharge pump of cast

iron body & bronze impeller with m.s.fabricated common base

plate, coupling, coupling guard, foundation bolts etc.,as required.

Model -KFE, Flow-97 m3/hr, Head-70 meter, Engine - 45 HP /

ph, Suc x Del - 100 x

263 Fire Hydrant Panel suitable for 10 hp Jockey pump, 40 hp (97 1.00 No 95445.00

m3/hr @ 70 m head) main electrical pump and 45 hp (97 m3/hr

@ 70 m head) Diesel engine operated pump

A) Incomer, MCCB - 1 Nos, R Y B Indication - 1 Set , VAF

Digital Meter - 1 Set, B) Outgoing , F1 40 HP Star Delta Starter -

For Main pump, F2 10 HP DOL Starter - 1 For Jockey, Pump , F3

Auto - On / Off Diesel Pump With Battery Charger, Control Circuit

With Auto - Manual On/Off, On/Off Trip Indication, On/Off Push

Button , C) Fabrication, Dully Powder Coated PO Red

Colour, Fabricated From 14/16 SWG,GI Sheet , IP-42 Protection,-

Fixed Type Floor Mounted, Cable Entry : Bottom

264 Pay Legal Fees to Concern Authority for Obtaining Plan Approval 5800.00 Sq.mt 12.12

and Final NOC

265 Filling available excavated Earth (Excluding Rock) in trench plinth 74.00 Cumt 130.39

side of foundation . in layer not excluding 20 cm in depth

consolidation each deposited layer by ramming and watering etc.

266 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 837.00 Pt. 485.81

1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length , in below

type of pipe erected with 6A Modular type switch / bell push &

accessories and earth continuity of following type, erected on

PVC / Metallic/Wooden box, single mounting base frame covered

with textured/metallic/white front plate modules erected on / in

wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed. (f) with medium

class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III

Item Rate In

Description of Item Quantity Unit Amount

No figures

267 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm 383.00 Pt. 674.68

(Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of

pipe erected with 6A Modular type switch and hum free EME

step type electronic fan regulator mounted and accessories with

earth continuity of following type erected on PVC /

Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall

/ ceiling as per pipe erected. with necessary ceiling rose /

H.D.Connector as directed. (f) with medium class Rigid PVC pipe

and accessories erected concealed in wall/ceiling complete.Cat. III

268 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm 2.00 Pt. 510.05

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of

pipe erected complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic/Wooden box covered with appropriate

front plate modules erected on / in wall / ceiling as per pipe

erected with following type of accessories. [I] For 6A Plug and 6 a

switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb

db board (f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

269 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm 3.00 Pt. 745.38

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of

pipe erected complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic/Wooden box covered with appropriate

front plate modules erected on / in wall / ceiling as per pipe

erected with following type of accessories. [II] For 16A Plug and

16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db board.(f)

with medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete Cat. III

270 Point wiring for on board Looped Plug with 6A Modular type 145.00 Pt. 257.55

switch & 5 pin socket erected on PVC / Metallic/Wooden box,

single mounting base frame covered with textured /

metallic/white front plate modules erected on / in wall / ceiling

with following type accessories Cat. III

271 Providing following type of Modular Type Accessories mounted 27.00 Ea. 151.50

with PVC / metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate , modules

erected with necessary connections as per site situation directed

by Engineer In charge. (1)One No. SP 6 Amp. Cat.III

272 Providing following type of Modular Type Accessories mounted 27.00 Ea. 151.50

with PVC / metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate , modules

erected with necessary connections as per site situation directed

by Engineer In charge. (2) One No 5 pin plug Cat.III

273 Providing following type of Modular Type Accessories mounted 248.00 Ea. 25.25

with PVC / metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate , modules

erected with necessary connections as per site situation directed

by Engineer In charge. (7) Blank Plate Single Cat.III

274 Providing following type of Modular Type Accessories mounted 13.00 Ea. 180.79

with PVC / metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate , modules

erected with necessary connections as per site situation directed

by Engineer In charge. (9) 16 Amp. SP one way switch Cat.III

Item Rate In

Description of Item Quantity Unit Amount

No figures

275 Providing following type of Modular Type Accessories mounted 37.00 Ea. 199.98

with PVC / metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate , modules

erected with necessary connections as per site situation directed

by Engineer In charge. (10) 6/16Amp. Universal socket Cat.III

276 Providing following type of Modular Type Accessories mounted 24.00 Ea. 410.06

with PVC / metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate , modules

erected with necessary connections as per site situation directed

by Engineer In charge. (14) 6A/ 10A/ 16A/ 20A/ 25A/ 32A

Double Pole Modular MCB Switch

277 Providing and erecting ISI mark Medium class RIGID PVC PIPES of 1848.00 Mtr. 24.24

following size complete to be erected on/in wall or ceiling

erected with necessary PVC fittings & Junction boxes fixed with

adhesive solution & Clamps with following dia of pipes, in

approved manner as directed (a)20 mm

278 Supplying and laying UPVC cable trunking system comprising 48.00 Mtr. 277.75

unplasticised polyvinyl, chloride rigid material with ignition free

and flame proof confirming BS with necessary end caps Internal

and external bend, flat bends, coupler, tee etc..All necessary

accessories and measuring of following sizes (1) 75 mm x 50 mm

279 Providing and erecting Mains with 1.1 KV grade FRLS PVC 3924.00 Mtr. 82.82

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /flushed on

wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of

following size (A) With medium class Rigid PVC pipe and

accessories (b) 2 wire 2.5 sq. mm

280 Providing and erecting Mains with 1.1 KV grade FRLS PVC 480.00 Mtr. 112.11

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected in / on wall / ceiling with

sq. mm copper conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size (A) with

medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq. mm

281 Providing and erecting Mains with 1.1 KV grade FRLS PVC 30.00 Mtr. 147.46

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected in / on wall / ceiling with

sq. mm copper conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size (A) with

medium class Rigid PVC pipe and accessories (b) 2 wire 6 sq. mm

282 Providing and erecting Mains with 1.1 KV grade FRLS PVC 600.00 Mtr. 260.58

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected in / on wall / ceiling with

sq. mm copper conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size (A) with

medium class Rigid PVC pipe and accessories (h) 4 wire 6 sq. mm

283 Providing and erecting Mains with ISI marked, 1.5KV grade 228.00 Mtr. 56.56

electrolyte multi stranded, annealed copper conductor with heat

resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel,

relays, power switchgears, motor starters & control wiring) with

required size of copper lugs, nuts and bolts if required. (e) One

wire 6.00 sq. mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

284 Providing and erecting Mains with ISI marked, 1.5KV grade 56.00 Mtr. 300.98

electrolyte multi stranded, annealed copper conductor with heat

resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel,

relays, power switchgears, motor starters & control wiring) with

required size of copper lugs, nuts and bolts if required. (i) One

wire 35.00 sq. mm

285 Supplying and erecting Flexible PVC insulated multi strand multi 1848.00 Mtr. 22.22

core 1.1 kv grade ISI marked copper wires of following size to be

erected as directed. (c) 1.00 Sq.mm 2 core round/ flat PVC

286 Supplying and erecting Flexible PVC insulated multi strand multi 294.00 Mtr. 46.46

core 1.1 kv grade ISI marked copper wires of following size to be

erected as directed. (e) 1.50 Sq.mm 3 core round PVC sheathed

287 Providing & erecting Switch board for Computer or electric 142.00 Ea. 1133.22

apparatus consisting of following modular type accessories

mounted with PVC / Metallic concealed/open box with single

mounting base frame covered with textured/metallic /white front

plate,modules erected with necessary connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat. III

288 Decorative call bell Ting-tong box type 250 volts complete erected 2.00 Ea. 71.71

289 Supplying and erecting LED indoor fittings with LEDs of wattage 700.00 Ea. 535.30

0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing

used as a heat sink shall be made of thick sheet Steel conforming

to IS: 513/CRCA/ aluminium die cast powder coated and high

U.V. & corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.95, THD <

15%, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt

,LED LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

between the ranges shown.) (A) Tube Light with integral driver

(v) 36-40 Watts, Surge-2 KV, IP-20, conventional 4 feet Cat-lll

290 Supplying and erecting led lamps with following wattage capacity 24.00 Ea. 112.11

of 220 to 240 voltage, minimum 15000 burning hours life, 500 V

in built-surge protection,Polycarbonate diffuser, mounting

suitable for E14 / E27 / B22 lamp holders, pf >= 0.5 (A) LED

Lamps integral type, with PC diffuser suitable LAMP holder (ii)

5 to 8 watts Cat-III

291 Supplying and erecting LED indoor fittings with LEDs of wattage 68.00 Ea. 1794.77

0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing

used as a heat sink shall be made of thick sheet Steel conforming

to IS: 513/CRCA/aluminium pressure die cast powder coated and

high U.V. & corrosion resistance with diffuser housed in

aluminium casted body with company mark/name 160V to

270V,Power Factor more than 0.95, THD < 15 %, CCT 3000 K to

6500K, Luminaire efficacy> 85 lumens/watt , LED driver

efficiency > 85 % ( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of

any wattage capacity between the ranges shown.) (B) LED Panel

Light with provision for Plane front frame with translucent cover

fixed to housing complete.IP20 (vi) 36 watts, 24" x 24", Surge-

2KV Cat-lll

Item Rate In

Description of Item Quantity Unit Amount

No figures

292 Supplying and erecting LED street light / Flood light fittings with 46.00 Ea. 5976.17

High power White LEDs wattage of 3 Watt and above assembled

on single MCPCB, efficiency more than 130 lm/w and corrosion

free High pressure die cast aluminum housing with smooth finish

powder coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy>

lumens/watt . LED driver efficiency > 85 %.( fittings required LM-

79 & LM-80 certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer incharge

Street Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage protection. (iii)

Above 60 to 90 watts Cat-lll

293 Supplying and erecting LED street light / Flood light fittings with 8.00 Ea. 9647.52

High power White LEDs wattage of 3 Watt and above assembled

on single MCPCB, efficiency more than 130 lm/w and corrosion

free High pressure die cast aluminum housing with smooth finish

powder coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy>

lumens/watt . LED driver efficiency > 85 %.( fittings required LM-

79 & LM-80 certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer incharge

Flood Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage protection. (vii)

(vi)above 160 to 200 watts Cat-lll

294 Supplying and erecting LED street light / Flood light fittings with 2.00 Ea. 4819.72

High power White LEDs wattage of 3 Watt and above assembled

on single MCPCB, efficiency more than 130 lm/w and corrosion

free High pressure die cast aluminum housing with smooth finish

powder coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy>

lumens/watt . LED driver efficiency > 85 %.( fittings required LM-

79 & LM-80 certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer incharge

Post Top Lantern LED fitting comprises of finish cast aluminum

spigot and spun aluminum canopy fixed with opal polycarbonate,

pipe arrangement for vertical mounting driver and accessories

wired upto terminal block.IP 65 (ii)32-40W Cat-lll

295 Pproviding and erecting Approved make Four pole moulded case 1.00 Ea. 6173.12

circuit breaker having breaking capacity ICU of 25 KA. at

V,having normal current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on A.C. supply 50 c/s.

with all internal connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing.ICS=100% of ICU only Cat III

Item Rate In

Description of Item Quantity Unit Amount

No figures

296 Providing and erecting Approved make Four pole moulded case 5.00 Ea. 8055.76

circuit breaker having breaking capacity ICU of 35 KA. at 415 V.

having normal current rating 125A. with Fixed thermal &

magnetic release suitable to work on A.C.supply 50 c/s. with all

internal connections, spreader tinned copper & complete erected

in existing 16 G.M.S. housing. ICS=100% of ICU only

297 Providing and erecting Approved make Four pole moulded case 3.00 Ea. 16221.61

circuit breaker having breaking capacity ICU of 35 KA. at 415 V.

having Normal current rating 200A.with variable Thermal &

magnetic release suitable to work on A.C.supply 50 c/s. with all

internal connections, spreader tinned copper & complete erected

in existing 16 G.M.S.housing ICS=100% of ICU only Cat III

298 Providing and erecting Approved make Four pole moulded case 2.00 Ea. 20946.39

circuit breaker having breaking capacity ICU of 35 KA. and above

at 415 V . having normal current rating 250A. with variable

thermal & magnetic release suitable to work on A.C.supply 50 c/s.

with all internal connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing. ICS=100% of ICU only

299 Supplying & erecting approved make Four Pole 415V change over 1.00 Ea. 13353.21

switch interior for panel mounting with operating mechanism

A.C.23 duty confirming to IS for (E)250A / 320A Cat-lll

300 Supplying and erecting triple pole & neutral 440V / 500V panel 2.00 Rn.Mtr 1961.42

mounting Copper Busbars with four equal Nos. of electrolyte bus

having current density not more than 1.6 Amp. / sq.mm (Rated

current / cross section area) duly wrapped with colour insulating

tape for phase sequence of following current carrying capacity,

erected with necessary bus bar supports /insulators, main cable

socket to each bar, erected in existing cubical panel with

necessary connections. (A) Suitable for 100 Amp. Capacity

301 Supplying and erecting triple pole & neutral 440V / 500V panel 1.00 Rn.Mtr 3202.71

mounting Copper Busbars with four equal Nos. of electrolyte bus

having current density not more than 1.6 Amp. / sq.mm (Rated

current / cross section area) duly wrapped with colour insulating

tape for phase sequence of following current carrying capacity,

erected with necessary bus bar supports /insulators, main cable

socket to each bar, erected in existing cubical panel with

necessary connections. (B) Suitable for 200 Amp. capacity

302 Supplying and erecting triple pole & neutral 440V / 500V panel 1.00 Rn.Mtr 4909.61

mounting Copper Busbars with four equal Nos. of electrolyte bus

having current density not more than 1.6 Amp. / sq.mm (Rated

current / cross section area) duly wrapped with colour insulating

tape for phase sequence of following current carrying capacity,

erected with necessary bus bar supports /insulators, main cable

socket to each bar, erected in existing cubical panel with

necessary connections. (C) Suitable for 300 Amp. capacity

303 Providing and erecting Miniature circuit breaker single pole 6A to 304.00 Ea. 112.11

25A suitable to operate on 240 V A.C. system and having breaking

capacity 10 KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark Cat.III

304 Providing & erecting 240 V MCB double pole switch for lighting 1.00 Ea. 278.76

Load (B Curve) having 10 KA breaking capacity & confirms to IS :

8828 in existing box having following capacity (A) 6 to 32 Amp.

305 Providing & erecting 240 V MCB double pole switch for lighting 4.00 Ea. 295.93

Load (B Curve) having 10 KA breaking capacity & confirms to IS :

8828 in existing box having following capacity (B) 40 Amp. Cat.III

Item Rate In

Description of Item Quantity Unit Amount

No figures

306 Providing & erecting 415V MCB Four Pole Switch for Lighting 50.00 Ea. 638.32

Load (B curve) having 10KA breaking capacity & confirms to IS

:8828 in existing box having following capacity (b)40 Amp. Cat.III

307 Sheets steel powder coated enclosure suitable for incorporating 3.00 Ea. 176.75

One/Two nos. MCB.

308 Providing and erecting Sheet Steel powder coated MCB 2.00 Ea. 1492.78

distribution board - flush / surface mounted fitted with busbar,

neutral link, earth bar and DIN rail, Conforms to IS 8623-1 &

IEC 61439-1 & 3 without MCB to house appropriate nos. of

MCBs.(The DBs should be used of same company of MCB to be

used) suitable for (A) single phase incoming and horizontal single

phase outgoing (b) sheet steel double door (IP-43) (iv)12 way

309 Providing and erecting Sheet Steel powder coated MCB 20.00 Ea. 2339.16

distribution board - flush / surface mounted fitted with busbar,

neutral link, earth bar and DIN rail, Conforms to IS 8623-1 &

IEC 61439-1 & 3 without MCB to house appropriate nos. of

MCBs.(The DBs should be used of same company of MCB to be

used) suitable for (B) three phase incoming and single phase

horizontal type outgoing Per phase isolation type (PPI) (b) sheet

steel double door (i)4 way

310 Providing and erecting Approved make RCCBs conforming to IS: 4.00 Ea. 1969.50

12640 and having sensitivity of 30 mA and Short Circuit

withstand capacity of 10 KA and suitable for operation on single

phase 240 V,50Hz. having characteristic of quick action & tripping

with all advance feature & do not incorporate any electronic

component. for following Max. rating erected as directed (i)

Amps.DP Cat. III

311 Providing and erecting Approved make RCCBs conforming to IS: 61.00 Ea. 2235.13

12640 and having sensitivity of 30 mA and Short Circuit

withstand capacity of 10 KA and suitable for operation on single

phase 240 V,50Hz. having characteristic of quick action & tripping

with all advance feature & do not incorporate any electronic

component. for following Max. rating erected as directed (ii)

40Amps. DP Cat. III

312 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 25.00 Kg. 794.87

313 Providing and erecting HOT deep Galvanised iron strip wire 8 to 66.00 Kg. 77.77

314 Providing and erecting Pipe type earthing having 150 cms.long 17.00 Ea. 368.65

and 2.5 cms. dia. galvanised iron pipe with coupling and buch

buried in specially prepared earth pit complete with necessary

SWG earth wire.

315 For using salt and charcoal / coke as required for pipe type 17.00 Ea. 171.70

Item Rate In

Description of Item Quantity Unit Amount

No figures

316 Supplying & erecting earth pit of minimum bore dia.150mm size 8.00 Ea. 4591.46

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive compound

with high charge dissipation suitable for following type of

applications with chamber and heavy duty cover. (A)(approved

make OEM has to submit test certificate including value of earth

resistance of installation duly stamped and signed by agency and

officer Incharge has to ensure the value of earthing resistane

mentioned in test Certificate) & having back filling compound of

(B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm /

meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no

load & dry form, Sulphar content:- <2%(C) Back fill Compound :-

Earthing compound should be capable to retain moisture for long

time Necessary test report must be submitted by Agency. (a) For

Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

317 Providing & erecting weather proof, dust & vermin proof, floor 6.00 Sq.Mtr 10468.65

mounted front operated indoor type cubical panel board

necessary IP-42 and above protection as per approval from

engineer incharge made from 14 SWG thick CRC M.S. sheet for

outer body & doors, 16 SWG thick CRC M.S.sheet for internal

partitions with necessary accesories , supporting angles/ flats

channel including cutting, bending, drilling, welding, riveting

with internal partitions & cable alley as per requirements &

instruction of engineer-in-charge with erection of supplied switch

gears, BUSBARS, suitable size of inter connecting PVC copper

wire / copper-aluminium strips, rubber grommets, rib, bakelite

control fuses/MCB for measuring instruments, earth bus & earth

bolts, foundation flange - bolts-base Plates, sufficient nos. of

hinged doors, handles with locking arrangement and rubber

gasket,heavy duty end terminal connection,danger notice

board,necessary ventilation,earthing strip complete. The Panel

shall be painted with epoxy powder coating. (The rates excludes

the cost of switchgears, bus bars, inter connecting mains &

Copper Aluminium strips, meters, Fuses etc. The dimension shall

be measured excluding base beams) The panel shall be supplied

with following approved manufacturers with following size. (A)

locally fabricated panel board (i) with 350mm depth

318 Providing , erecting , fabricating the M.S. structure as per 80.00 Kg. 77.77

requirement on site incorporating proper size of M.S.

angles,square,round, flats, bars, channels, sections complete with

cutting, welding, grinding & finishing duly painted with one coat

of red oxide with erection on site as per direction of engineer in

charge with necessary grouting, cementing, plastering & finishing

319 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 40.00 Mtr. 92.92

Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of

cables. (B) 2 core 6 Sq. mm

320 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 28.00 Mtr. 490.86

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following

size of cables (E) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core)

Item Rate In

Description of Item Quantity Unit Amount

No figures

321 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 235.00 Mtr. 540.35

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following

size of cables (F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)

322 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable 1168.00 Mtr. 126.25

multistrand / Solid Aluminium conductor for 1.1 KV. to be laid

on wall with necessary clamps or in existing trench / pipe of

following size of cables (B) 4 core 6 Sq. mm

323 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable 40.00 Mtr. 153.52

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following

size of cables (A) 4 core 16 Sq. mm

324 Making trench in soft soil of suitable width of 90 cm deep for 982.00 Mtr. 55.55

laying cable or locating the fault all over the run and back filling

the same and making the surface as normal ground.

325 Supplying following size of Light duty “A” Class G.I . Pipe & 20.00 Mtr. 300.98

erecting as directed by Engineer-in-charge. (B) 50 mm dia

326 Supplying following size of Light duty “A” Class G.I . Pipe & 14.00 Mtr. 696.90

erecting as directed by Engineer-in-charge. (D) 100 mm dia.

327 Providing & laying approved make Double walled corrugated 842.00 Mtr. 62.62

pipes (DWC) of polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same material at required

depth in existing trench for laying of cable. below ground / road

surface for enclosing cable (A)50 mm outer dia

328 Providing & laying approved make Double walled corrugated 148.00 Mtr. 137.36

pipes (DWC) of polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same material at required

depth in existing trench for laying of cable. below ground / road

surface for enclosing cable (D)120 mm outer dia.

329 Providing and, fixing heavy duty flange type brass cable gland 17.00 Ea. 38.38

with rubber ring for PVC insulated armoured cable complete with

out going tails, insulating tape etc for following size of cables. (B)

2 to 4 core 6 Sq. mm

330 Providing and, fixing heavy duty flange type brass double 4.00 Ea. 131.30

compression type cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails, insulating tape etc

for following size of cables. (D) 3 & 1/2 core 95 Sq. mm

331 Providing and, fixing heavy duty flange type brass double 8.00 Ea. 140.39

compression type cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails, insulating tape etc

for following size of cables. (E) 3 & 1/2 core 120 Sq. mm

332 Solder less crimping type Aluminium lugs conforming to IS 4.00 Ea. 20.20

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner. (D)

333 Solder less crimping type Aluminium lugs conforming to IS 2.00 Ea. 25.25

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner. (E)

334 Solder less crimping type Aluminium lugs conforming to IS 18.00 Ea. 40.40

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner. (F)

Item Rate In

Description of Item Quantity Unit Amount

No figures

335 Solder less crimping type Aluminium lugs conforming to IS 28.00 Ea. 45.45

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner. (G)

336 Providing & erecting Approved make Power Saving 50 Watt 383.00 Ea. 1948.29

Ceiling Fan with double ball bearing ISI mark with Condenser

volt A.C. 50 Hz 1200 mm sweep complete having 3blades with

aluminium blades with , canopy & 30 cm. down rod erected with

earthing.(Make shall be approved by Engineer in charge))

337 Supplying and erecting 19 / 20 mm. nominal bore Medium Class 383.00 Mtr. 108.07

M.S. Pipe down rod erected duly painted for fan complete with

proper insulation without leakage and earthing.

338 Supplying & erecting fan hook box of 10 mm M.S. round bar 383.00 Ea. 108.07

bounded to the RCC bars up to 50mm length each side and

pierced through a 16 Gauge M.S. box / Heavy Duty PVC box

complete erected concealed in Ceiling with necessary finishing.

339 Providing 2.5mm.thick laminated acrylic sheet to cover the fan 383.00 Ea. 18.18

hook or Fan box.

340 Supplying & erecting approved make low noise decorative 3.00 Ea. 1366.53

exhaust fan having square frame ABS body with inbuilt lowers &

square frame. 250mm with 1350 RPM Cat.II

341 Supplying & erecting single phase approved make industrial 40.00 Ea. 2054.34

exhaust fan suitable for medium duty ring mounted low noise

operation suitable for medium duty having following dia size and

maximum speed in RPM [A] 305 mm dia 900 RPM Cat.II

342 Supplying and erecting approved make Octagonal pole made from 32.00 Ea. 8192.11

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759,

suitable suspend local wind speed with integral Junction box

consist of terminal plate of min 6mm Hylam sheet, standard

profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type

terminal and arrangement for cable termination to be erected

With Suitable foundation (Included) as per details given by

manufacturer considering site requirement. (D) 6 Mtr. Long

mm Top X 135 mm bottom dia, 3 mm thickness with

200mmX200mmX12mm base plate, 4-M20 Bolts and 600mm long

J-Bolt.Approx Pole weight 59 kg

343 Supplying & erecting approved make SMC press moulded 10.00 Ea. 515.10

composite FRP. loop-in, loop-out approx. 2mm thick box

complete with Bakelite connector strip 5way(3P+N+E),DIN rail

for mounting mob & hinged doors as per requirement having

locking arrangements with mounting clamp with nuts, bolts &

washers suitable for erection on pole with cable clamps& earth

bolt of following size of box. (B) 250mm x 200mm x 100mm

Supplying and erecting Street light pole bracket comprising main 18.00 Ea 491.87

B Class GI pipe of 4.2 cm/require outside dia. complete with

suitable B Class G.I. sleeve tubing of approx. 45cms.length and

suitable for 76.5mm/80mm/require size of pole top having nuts

and bolts for fixing the brackets and having spread of 0.5 mtr.

Length with 110 deg.with vertical plane and suitable welded

stiffener reducer and nipple with check nut complete painted

with one coat.of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of arms. [A] Single

Arm bracket 0.5 Mtr

Item Rate In

Description of Item Quantity Unit Amount

No figures

345 Supplying and erecting Street light pole bracket comprising main 14.00 Ea 622.16

B Class GI pipe of 4.2 cm/require outside dia. complete with

suitable B Class G.I. sleeve tubing of approx. 45cms.length and

suitable for 76.5mm/80mm/require size of pole top having nuts

and bolts for fixing the brackets and having spread of 0.5 mtr.

Length with 110 deg.with vertical plane and suitable welded

stiffener reducer and nipple with check nut complete painted

with one coat.of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of arms. [B]

Double Arm

346 Supplying & Bracket

erecting0.5 Mtrgrade following size section pillar

fabricated from joint less M.S. Sheet with angle iron legs made

from jointless M.S. Angle with cable clamps to be buried in ground

to have appropriate erection to work uniform until erected with

cement concrete foundation and 45 cm high bricks work finishing

with plaster etc. hinged double door internally supported on both

side, with internal and outside looking arrangement with look

and keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one

is welded and other with nut and bolt for erecting Bakelite sheet.

Painting the Section Pillar inside and out side with three tank

powder coated paint. section pillar roof should be without joint

with water leakage proof & tested as per IP 55 test & followed by

IS 2147 of 1962 (B) 75 X 60 X 45 cm section pillar fabricated from

16 Gauge MS Sheet with angle iron legs 45 cm long made from

X 35 X 5 mm thick MS angle.

347 Supplying and erecting HYLAM sheet on existing angle iron 1.00 sq.mtr 1541.26

frame.for following thickness (D) 8mm

348 Supplying and erecting nuwood 12 mm thick on existing angle 1.00 Sq.Mtr 291.89

iron frame.

349 Providing and erecting Inverter based approved make Cassette 16.00 Ea. 80731.32

type split air-conditioning unit consisting of condensing unit with

fan motor, hermetically sealed scroll/rotary compressor with

accessories etc. duly connected separately erected evaporating

unit and blower motor with its accessories by Eco friendly Green

gas charging & Internal copper wiring & Remote control ( 3 star

and above of current year) with necessary core cutting. (B) for

ton capacity

350 Supplying and erecting insulated pair of soft copper tubing open 154.00 RMT. 965.56

or concealed including power and control cable,necessary PVC

drain pipes for Split AC machine up to 4 TR capacity

351 Supplying and erecting approved make Single phase power 16.00 Ea. 3232.00

conditioners suitable for input voltage 180V / 280V, output

voltage 220V (+ / - 10%) AC 50 ‘Hz with electronic relays &

component of housed in sheet metal cabinet ‘with epoxy powder

switch, 5/15 A universal socket with range off (D) 4 KVA

352 Providing & erecting water cooler having storage capacity 150 3.00 Ea. 55893.40

Ltr. & cooling capacity 150 Ltr.per hour @ an ambient temp of 45˚

C. The outlet temp. of the water should drop by 15˚C within a

hour, The water cooler should be comprising of hermetically

sealed compressor, fan motor, condensing unit, water tank

surrounded by evaporating, coil, thermostats, relay etc.complete

with necessary inlet & outlet connection. The body of water

cooler will be made from Stainless Steel.

Item Rate In

Description of Item Quantity Unit Amount

No figures

353 Supplying & erecting reverse osmosis (RO) water purification 3.00 Ea. 77891.20

system with M.S. powder coated pedestal frame, prefilter housing

carbon filter suitable buster DC pump, auto low & high pressure

switches with following size of LPH capacity & erected as directed

[D] 100 LPH with 1 phase / 3 phase Raw water pump of 500LPH

@ 2.5kg/cm2 - (1N0 - Kirloskar /CRI/Lubi), Dual media filter

10"x54" - (1 No), Micron cartridge filter 20" x 2.5" ( 1No), High

pressure pump 500LPH @ 10kg/cm2 - (1No - Shimge /CRI /Lubi),

RO Membrane housing with RO membrane of 40*40 - (1No), RO

pressure tube 4" x 1E - ( 1No), 0 - 1200LPH Rotameter -(2 Nos),

with Recovery Rate 50%.

354 Supplying and erecting approved make panel mounting type 4.00 Ea. 1275.63

Digital Voltmeter having 3 digits LED display, 0 to 750 AC Volts

range erected on existing panel board with all connection, wiring

etc .with manufacturers calibration certificate.

355 Supplying and erecting approved make panel mounting type 4.00 Ea. 1558.43

Digital Ammeter having 3 digits LED display, external CT

operated, calibrated for 0 to 1000 Amps suitable to operate on

500 Volt AC , erected on existing panel board with all connection,

wiring etc .with manufacturers calibration certificate.

3 phase AC Supply 500 V on existing panel board with necessary

connections.

357 Providing & erecting L.T. Current Transformer with bar primary 12.00 Ea. 274.72

50/5 to 1000/5 ratio 15 VA burden erected in existing CRCA box

duly secured with insulating materials connected to the meter

358 Supplying and erecting approved make suitable panel indicator 12.00 Ea. 43.43

LED type lamp, lens cover, complete erected with necessary

connections.

Supplying and erecting, commissioning and testing of Diesel

Generating set confirming to IS: 4722:1968 & BS:5514 having

continuous rating, 3 phase, 415 volts, 50 cycles A.C. supply

comprising of a totally enclosed air/water cooled diesel engine

with multi-cylinders developing suitable BHP not less than

following capacity at 1500 RPM with 10% overload for one hour

in 24 hours with standard accessories like fly wheel, lubricating

oil cooler, "A" class governor, heavy duty fuel wheel and

lubricating oil filter, oil bath air filler, lubricating oil pressure

gauge, end exhaust manifold, standard set of tools with adjustable

spanners, screw drivers, cylinder head to cover, joint cylinder

head to exhaust, element lube oil filter, 12 / 24 volts electric

starting equipment complete with standard heavy duty battery,

dynamo, cut-outs, ammeter, necessary wiring, pressure gauge,

starter etc and heavy duty Residential type exhaust silencer and

vertical hot air duct both

logged with asbestos rope, save oil trays, exhaust piping of

required length, standard wall/floor mounted fuel with level

indicator and piping and drip proof alternator, self excited, self

regulated, screen protected, with excitation system, capable of

delivering the rated system output at 415 volts, 3 phase, 0.8 PF,

50 Hz, 4 wire, running at 1500 RPM, conforming to IS-4722-

with voltage regulation +/- 5% of rated voltage from no load to

full load. Both the engine and alternator fitted on a common

fabricated steel base plate with antivibration mounting engine

and alternator both connected to each other by flexible flange

coupling and with floor/wall mounted control panel box

MCCB / MCB of adequate capacity,

Item Rate In

Description of Item Quantity Unit Amount

No figures

359 indicator lamps duly wired with HRC fuses. The alternator & 1.00 Each 1029194.04

control panel shall be connected with provided suitable capacity

armoured cable and complete with Acoustic enclosure (canopy)

made out of 16 SWG CRCA Sheet, sound absorbing material

Rockwool of 64 density & 100 mm thick conforming to IS:8183 /

PU Foam of 40 Density - at least 40 mm. The resin bonded

rockwool covered from inside the canopy by perforated sheet

with 3/4 mm holes, sound level not more than 75 dB at a distance

of 1 mtr, as per PVCT norms. Erection, commissioning and

satisfactory testing as per requirement with first filling of fuel, oil,

etc. with guarantee / Warrantee of complete system for Two

years. & with obtaining all necessary certificate from Electrical

Inspector. The Capacity and Ratings of DG sets are as below.(M)

Continuous rating of 125 KVA ,BHP not less than 154 BHP

360 Supplying & erecting Amplifier having following specification: 1.00 Ea 11298.87

Power Output :250W (RMS) (300W Max.)

inputs : 6 Misc. & 2 Aux.

frequency Response :50-1500HZ I3db

Tone Controls :Cut & Boost type

LED Meter :5 LED Arrays

The amplifier suitable to operate 240V A.C.& 24volt D.C. (Battery)

with automatic changeover from AC to Battery operation, duly

protected by wrong Battery Polarity connections. [[Approved by

Competent Authority i.e. not Below the rank of Executive

Engineer ]

361 Supplying & erecting Booster Amplifier having power output of 1.00 Ea. 9672.77

25OW (RMS,), suitable to obtain combined power output of two,

with 6 mike inputs & suitable to be used independently as a

250watt amplifier in combination with mike & mixer. The booster

Amplifier shall be without mike &Aux. input channels, The system

shall be suitable to operate on 24OV. A.C. & 24 Volts D.C. Battery.

[[Approved by Competent Authority i.e. not Below the rank of

Executive Engineer ]

362 Supplying & erecting recess wall mounting speaker with 5W rated 66.00 Ea. 591.86

input power 3.3 K. Ohms / 3W impedance, 100 - 10000 Hz

frequency response with 6 inch dia. cone type 8 ohms speakers

duly fitted in ABS plastic cabinet of colour match with wall or

ceiling of following size. [[Approved by Competent Authority i.e.

not Below the rank of Executive Engineer ] (b)Square shaped

x 260mm size speaker

363 Supplying microphones stands with sturdy mechanism, treble 2.00 Ea 445.41

free movement & positioning of microphones, free from rust with

superior quality of chrome plating with following size.

[[Approved by Competent Authority i.e. not Below the rank of

Executive Engineer ] (c)Fixed height 91 cms. & extendable up to

62 cms. with round base of dia. 23 cms.

364 Supplying, installing and testing approved make microphone for 2.00 Ea. 1284.72

All purpose, with frequency response of 100 - 11000 Hz, having

sensitivity 2.2mv / Pa & impedance 500 Ohms (LO- Z) supplied

with quick detachable holder, 6 mtr twin core cable & 3 pin XLR

connector. [[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

Item Rate In

Description of Item Quantity Unit Amount

No figures

[1] GEAR LESS LIFT DRIVE (MRL) comprising of High Starting

torque Lift 3 phase 440 V A. C. Permanent Magnet Synchronous

motor of proper rating with high efficiency shall be used.[2] Micro

processor based / PLC, ACVVVF, vector control drive with

encoder feedback closed loop system shall be used for lift car and

hall call demand response, UP/DOWN hall stops, Main, Up/ Down

Contactor with overload and phase reversal relay and safety

controls. [3] Car with M S platform with bracings of adequate size

and to sustain the impact load cabin + passenger with safety

factor of fire for steel and side panels of Stainless steel of sheet of

grade 304 duty. Car ceiling will be S.S. finishes with aesthetic

appearance with LED ceiling lights. Car flooring shall be of s/s

chaker plate design sugeested of engineer in charge. of engineer

in charge. Car doors shall be of stainless steel grade 304, hairline

finish with centre opening / telescopic automatic doors. Car panel

will also be S.S. 304 finished with emergency stop device,

mechanical door safety device, facility of auto/ attended mode. All

car panel buttons and all floor switches must be with brail

language as per lift act. [4] All landing doors must be fire rated for

2 hour shall be fully automatic centre opening/ telescopic

opening made of hairline finish steel grade of 304 with key holes

and infrared curtains with Unlocking facility from outside

[5] Appropriate battery operated emergency light in the car along

with alarm switch shall be provided. Also, Emergency Light & Fan

should start immediately without any Time Delay as soon as

power fails.

[6] Digital scrolling indicator system for up-down arrow along

with floor position indicator shall be provided inside the car and

at all floors.

[7] Full height infra red curtain with multiple cross / crossing

light beams shall be provided.

[8] Automatic Rescue Device (ARD) shall be provided accordingly

of passenger capacity with Manual Rescue Operation ( Manual

Cranking Facility).

[9] Audio visual indication in the lift car showing over loading

shall be provided such that doors kept open till excess load is

removed. [10] Spring buffers/PU Buffers shall be provided.

[11] Car fan as per passenger capacity with automatic sleep timer

shall be provided.

[12] Voice annunciator with suitable music shall be provided in

[13] Self diagnostics system for operational and safety

parameters shall be provided in control panel.

[14] Mechanical over speed governor with governor calibration

as per actual site parameters and submission of calibration

certificate submission, door key holes in the floor doors, fireman

switch shall be provided.

[15] Lift machine hoisting arrangement in the lift machine room

and monkey ladder for lift pit should be provided by the lift

agency, along with the other steel structure works, foundations

for the machine etc…

[16] In the hoist way fascia plate shall be provided without any

extra cost, where ever required as / if directed by engineer in

Item Rate In

Description of Item Quantity Unit Amount

No figures

[17] Permanent wiring with necessary safety devices like RCCB in

all circuit, Over Voltage Under Voltage protection and THD

eliminator in circuit for lift machine room and lift well with

proper numbers of light points, with fixtures, exhaust fan and plug

points shall be provided by the agency. Only 3 phase Power

Supply shall be made available by department in lift machine

room. Necessary Earthing as per Lift Act/Rules shall be arranged

by Lift Agency.

[18] Any civil/ electrical works for additional and alteration in lift

shaft and machine room related to erection of lift shall be made

by lift agency without any extra cost. (granite/marble fixing

around all landing door openings are not in lift agency’s scope.)

[19] Agency has to provide all working drawings and documents

and liaison services for obtaining all necessary permission from

lift inspector and other authorities. [20] acrylic transparent

licence/display A4 size holder in lift car [20A] As per statutory

requirement of Govt. Of Gujarat lift & escalator act 2000, lift

agency has to provide

1. Car top safety barricade

2. Push & talk communication system.

3. Fireman's switch operation at Ground Floor.

4.carrying out third party lift inspection

during/after lift erection and provide report by third party

authorized by concern licensing authority 5.agency has to

provide third party insurance upto completion of free

maintenance period and submit the document for the same.

[21] Car Panel Operating Buttons with floor position

indicator/buttons must be of Auto Glow type clearly visible when

view from inside cabin.

[22] For Physically Handicapped person Full Length Handrails of

hairline finish steel grade of 304 should be provided at

appropriate height on the Rear & Side Wall Panels in Lift Car.

[23] With Necessary KVA rating voltage controlled Stabilizer

suitable for your controller, drive and all equipments of lift.

[24] Necessary rating of DP Elcb and FP Elcb required for lift is in

scope of work which rating is sugested by CEICED Department

(electrical Inspector)

(B) SPECIAL FEATURES DESCRIPTION OF LIFTS for PREMIUM

1. Advanced control system dual 64 bit embedded

microprocessor with CANBUS Serial Communication mode

including Regenerative power efficient operation,on site

programming facility, Anti nuisance, Pte-opening, BMS/RMS with

necessary online real time monitoring system having necessary

connectivity for remote monitoring & other suitable supporting

hardware & software devices to fulfil the purpose. 2. Floor

Indication LCD Display with call registration & brail mark with

arrival gong and hall lantern & TFT Screen in the car with MP3

Voice Announcer. 3. CAR Panel should be Scratch resistive SS

Moonrock finish / Hair Line / Honeycomb for car and all Doors,

All landing doors must have fire rating up to 2 hours and car door

must have multi-level crisscross beam door protection. 4. To & fro

communication system & wiring (i.e. car , control room & guard

room ) and Each elevator are equipped with remote monitoring

system.agency has to provide mobile app and user id and

password for monitoring

365 10 Passengers, Ground plus 2 upper floor with Rated Speed of 1.00 Ea. 1474779.78

1.0 m/sec., (C) With General PLUS ADDITIONAL SPECIAL

FEATURES attached herewith. Prem. Cat.

Item Rate In

Description of Item Quantity Unit Amount

No figures

Supply, Installation, Testing & Commissioning of following size of

Grid Tied Solar Power Plant with

Solar Panels (ALMM approved): Frame Material : Anodized

Aluminum alloy Frame With Twin Wall Profile, Front Cover : High

Transmission Low-Iron Tempered Glass (AR Coated), High

efficency and positive power tolerance Pmax: 0/+5, Module

Efficiency should be approx. 19.5%-22%, Normal operating

temperature 45'C, Junction Box with Waterproof IP67 & MC4

Compatible and Enclosed with Bypass diodes, 100%

Electroluminescence test to ensure error free Modules, Thep.

temp. co-efficient of the PV module shall equal or better than -

0.45%/degree C. Solar PV modules of minimum fill factor 75% to

be used. Unit Production:- More than 4.5 Unit /kw /day

(Actual)(1Year Avg) With 10 year Product warranty and 25 year

Linear Power Warranty includes all mechanical and electrical

parameters of the Solar panel. Modules must be complied to the

DCR(Domestic content requirements). The Ration of AC to DC is

5:6 for the Installation capacity which are given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V , Max

efficiency: 97.5% - 98.9%, O/p Frequency: 50/60Hz, Operating

Altitude (m) ≤4000, O/p Power Factor: ~1, O/P THDi: <3%,

Operating Tempreture Range: -25~60°C, Integrated protection of

Inverter are Anti-islanding Protection, Input Reverse Polarity

Protection, Insulation Resistor Detection, Ground fault protection,

Residual Current Monitoring Unit, Output Over Current

Protection, Output Short Circuit Protection, Output Over Voltage

Protection, PV array string fault Protection. Protection Degree:

IP65, User Interface LCD & APP, Datalogger & Communication:

GPRS / Wi-Fi.

Integrated, Input Reverse Polarity Protection Integrated,

Insulation Resistor Detection Integrated, Residual Current

Monitoring Unit Integrated, Output Over Current Protection

Integrated, Output Short Circuit Protection Integrated, Output

Over Voltage Protection Integrated, Protection Degree: IP65, User

Interface LCD & APP,Datalogger & Communication: GPRS / Wi-Fi,

Module Mounting Structure: The mounting (Rectangular pipe /

square pipe / circular pipe) with requisite cross bars, nuts and

bolts, etc. shall be Hot deep galvanized with minimum 80micron

coating. The Rectangular / square /circular hollow pipe section

used for the structure should have a minimum thickness of

mm. other than above, the material thickness should be minimum

2.5 mm. A certificate of a structural engineer certifying the

strength and stability of the mounting structure to withstand the

weight and wind speed of 150 km/hour throughout the life span

of 25 years of the system, shall be submitted by the vendors. Hot

Dipped Galvanized steel coils. suitable arrangement for base plate

for foundation , solar panel mounting, the structure should be

suitable for carry the load of solar panel,wiring, sprinkler system

etc. with necessary foundation work/wall mount, j bolt, anchor

fastner etc. the nut bolt used for installtion of stucture should be

(SS 304) quality.The ground clearance of the bottom most edge of

solar panel shall not be less than 300 mm to 1200 mm or as per

site’s technical/feasibility requirement. a. Column –The minimum

section (thickness) should be 60MM*40MM b. Rafter - The

minimum section (thickness) should be 60MM*40MM c. Purlin -

The minimum section (thickness) should be 40MM * 40MM

Balane of System with necessary Swichgears (Suitabel size and

protection of ACDB & DCDB), inter connecting wiring, earthing

system as per the CEIG drawing approval, lightining arrester

Item Rate In

Description of Item Quantity Unit Amount

No figures

366 (Excluding GEDA Application fees, Solar connectivity Charges, 75.00 PER KW 40658.56

Meter connectivity Charges, Meter testing Charges.) (F) Grid Tied

Solar Power System: 101 - 250 kW (3 - phase)

Total Rs.

I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures and words) of the

estimated rate mentioned above. Amount of my /our

Tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for

1 which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement

Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per actual mix

4 design the cost of difference of cement consumption have been deducted from the rate of original item at the rate of input rate

mentioned in all the tender.

Deputy Executive Engineer Executive Engineer

Vapi ( R & B ) Sub Division Valsad ( R & B ) Division

Vapi Valsad