Day to day annual maintenance S and P and Building works at Mal Sub Divisional Hospital and Doctors Quarters Non Residential Mal Sub Division PWD during 2025_26

Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6 m height for external wall) (i) 3 mm thick (weighing 7.4 kg/Sq.m)

Extra for fixing glass panes in steel window.

Labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damaes complete. (Concrete and brick work for mending damage will be paid separately) (a) Upto area 2.5 Sq.m

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). (d) Sal : Local.

d) Sal : Local. (add above GL-1ST FLOOR)

Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. (In case of non-supply of single plank, penal rate of reduction of 20% will be made)(iii) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm. (b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak.

Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. (vii) 100mm. X 58mm. X 1.90mm.

Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: (iv) 150mm long x 10mm dia. bolt.

(ix) 300mm long x 10mm dia. bolt.

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (a) With continuous plate base (Hexagonal/ Round rod (vi) 150 mm grip x 10 mm dia rod.

Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of 59 mm x30 mm section with 2.0 mm (+/-0.2 mm) wall thickness.Horizontal & vertical section shall be fixed to each other by self tapping screws and 1 solid polymeric or M.S. galvanised tubular 'L' shaped bracket 100mm x 200mm in each corner of the shutter frame for placing hinges. Polymer based multicavity hollow section of 120 mm x30mm with 2.0 mm (+/- 0.2 mm) wall thickness will be fitted in the middle, reinforced by solid polymer bar of 200 mm long at both ends and screws from both sides as lock rail. The section frame will then be fitted in by PVC panels of size 100 mmx25 mm with wall thickness of 1.2 mm (+/- 0.2 mm) and 2 nos. of 6 mm dia bright rod will be inserted horizontally with both side check and nut system and stretches where fixing of hinges / hasp bolt / tower bolt / door ring are required to be strong enough to with stand wear and tear. The rate is inclusive of cost of all materials,labour, and hire of tools and plants and appliancesi/c carriage of all materials taxes and all other incidental charges complete.

Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 205/66) and fitted and fixed with cadmium plated screws: (v) 100 x 63 x 3.2mm.

Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted and fixed complete. (i) 250mm x 16mm dia bolt.

Glazed shutters of doors, windows, fan light, clerestory windows etc. as per design (with ordinary glass of 7.4kg./sq.m. 3mm. Thick) fitted with putty bed and teak wood bead and nails including fitting and fixing shutter in position but excluding the cost of hinges and other fittings. cost of glass, putty, wooded beads etc.will be paid separately. In ground floor. (i) 40mm thick shutters. (b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak.

Taking out door shutter and rehanging the same by fixing aluminium sheet [0.457 mm] with proper nail etc.

Removing old scales, blisters etc. of interior surface of walls,ceiling by scraping etc. and preparing smooth and even surface with rendering or cement mortar (1:2) (as necessary), to make the surface suitable for receiving distemper. (Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge).

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface. Two Coats

White washing including cleaning and smoothening surface thoroughly. All floors : (b) Two coats (to be done on specific instruction).

i) Hydraulic door closer of approved quality as per I.S.I. standard fitted and fixed complete. (b) Medium (I.S.I. size 2)

Styles and rails of wooden shutters fitted and fixed complete. (Payment to be made on area of new work only). In Ground Floor: (ii) 35mm Thick shutter. (b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak.

Supplying bubble free float glass of approved make and brand. Conforming to IS: 2835-1987.(iii) 5 mm thick clear glass.

Stripping off worn out plaster and raking out joints of walls, celings etc. up to any height and in any floor including removing rubbish with in a lead of 75 m as directed

Supplying fitting and fixing I.R.C. fabric mesh with covering battens includingcost of screws etc complete (excluding the cost of battens).In ground floor(j) 25mm x 25mm x 2.2mm x 2.2mm.

Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface].(ii) With 1:4 cement mortar .(c)10 mm. thick plaster.

(i) with 1:6 cement mortar.(b) 20 mm. thick plaster.

Brick work with 1st class bricks in cement mortar (1:6)In Super structure, ground floor.

Supplying profiles of requred section made of Aluminium Alloy extrusions conforming to IS:732-1983 and IS:1285-1975; Annodized (with required film thickness and specified colour/natural) matt finished conforming to IS: 1868-1983 for fabrication of composite door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed/ certified make and brand as per direction of Engineer-In- Charge . (Payment will be made on finished length of the work).(A) In 10-12 Micron thickness Annodizing film.(I) Natural White.(k) Movable door shutter.(i) Door frame (Top & sides).

(A) In 10-12 Micron thickness Annodizing film.(I) Natural White.(k) Movable door shutter.(ii) Shutter :(a) Top rail.

(A) In 10-12 Micron thickness Annodizing film.(I) Natural White.(k) Movable door shutter.(ii) Shutter :(d) Door vertical.

Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium section for the following units:-.(B) Partly glazed partly panelled of fully glazed single leaf aluminium swing door made of extruded and anodised alloy aluminium sections, fabrication, including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages, with top pin assembly of approved make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries , cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated / particle block ) fixing them with glazing clips as per drawing , specification and direction of Engineer-in-Charge. (Add. above ground floor - 1st. floor)

Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan orsimilar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings in ground floor(b) 32 mm thick shutters (single leaf)

Dismantling all type of masonry excepting cement concrete plain of reinforced stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m..(a) In ground floor including roof.

(a) M.S. or W.I. ornamental grill of approved design joints continuously welded with M.S., W.I. flats and bars for windows ,railing etc. fitted and fixed with necessary screws and lugs in ground floor. (Add extra @1% for each addl. floor up to 4th floor and @1.25% for each addl. floor above 4th floor). (i) Grill weighing above 10 kg./sq.m.and up to 16kg/sq.m.

Supplying fitting and fixing in position approved P.V.C. door frame (Matt finish)made of extruded P.V.C. multichamber hollow section having dimensions 60mm x50mm x 2mm (+/-0.2mm), horizontal section will be joined with vertical sectionby galvanised steel screws after inserting two number steel brackets asreinforcement making suitable space for placing hinges, one steel tube 40mm x20mm x 1.20 mm will be inserted on one full vertical side of the frame (hinge side)as reinforcement, the frame will then be fixed in the opening with the help ofP.V.C. expandable fastner/wooden gutties and galvanised steel screws includingcost of all materials and labour, hire charges of tools and appliances, carriage ofall materials, taxes and all other incidental charges complete.

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Priming one coat on timber or plastered surface with synthetic enamel oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand parpering etc. in cluding using of approved putty etc. on the surface , if necessary.(b) On steel or other metal surface: (1) With super gloss (hi-gloss).(iv) Two coats (with any shade except white).

(a) On timber or plastered surface: (1) With super gloss (hi-gloss).(iv) Two coats (with any shade except white).

Ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttring and reinforcement, if any, in ground floor as per relevant IS codes.(b) River bazree.

Neat cement punning about 1.5mm thick in wall, dado, windowsill, floor etc.NOTE:Cement 0.152 cu.m per100 sq.m.

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor.

Hire and labour charge for shuttering with centreing and necessary staging up to 4 m. using approved stout props and thick hard wood planks of approved thick ness with required bracing for concrete slabs, beams, columns, lintels curved or staight including fitting fixing and striking out after complection of works. (up to roof of ground floor).

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at inter-section, complete as per drawing and direction.

Ordinary cement concrete (mix 1:1.5:3) with graded stone chips (20mm nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant codes. (i) Pakur Variety.

Reparing collapsible gate by cutting out all rivets as necessary reassamblingall members including welding pieces of channels,sraightening bent bars and rivetting with new rivets and fitting inposition and painting two coats.

Supplying PVC rollers for sliding windows as per direction of Engineer in charge.

Supplying EPDM gasket of approved make and brand as per direction of Engineer-in -charge.

Supplying Weather Silicon of approved make and brand for fixing of grove line between the Glasses as per direction of Engineer-in - charge.for Structural Glazing/Curtain wall Weather Silicon for filling the Grove line between Glasses or any other material for facial work, Glazing silicon for fixing glass on sub frame.

Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16 mm dia rod with centre bolt and round fitting.

Taking out M.S. or W.I. grills from wooden frame including cutting lugs from masonry wall and refitting the same and mending good damages after repairs (excluding the cost of necessary repair of damages) or doing any other necessary works.

Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. and cutting trenches in any soil through masoury concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen/M.seal etc) complete. (A) UPVC PIPES. (ii) 110mm Dia.

(A) UPVC PIPES. (iii) 160mm Dia.

(B) UPVC fitting:. (a) plain tee. (ii) 110mm Dia.

(B) UPVC fitting:. (c)bend 87.5 degree. (ii) 110mm Dia.

Supplying 1.5 mm. thick M.S. sheet fitted and fixed on one or both faces of M.S./W.I. gate etc. with point welding at not more than 150 mm. apart complete in all respect as per design including cost of all labour and materials.

supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar , end bifurcated with necessary screws etc. by cement concrete (1:2:4) as per direction . ( cost of concrete will be paid separately). (a) 40mm x 6mm, 250mm Length .

Easing, oiling and adjusting the steel shutters including scraping allmembers and fitting so as to make the shutters easily operable (noextra payment will be made for taking out and fixing glass, ifnecessary). (Each means a pair of shutter in a frame)

Renewing hinge of steel shutter including taking out old one bycutting and fixing new hinges by welding and mending gooddamages complete

Easing door and window.

Labour for taking out rolling shutter (only shutter portion), dismantling by parts for repair (or replacement of damaged parts only),rehanging and re-fitting the same in position after necessary repairs (excluding the cost of supply of new parts).

(A) Iron door ring of approved quality fitted and fixed with nut and washer complete. (ii) 75 mm. dia.

Clearing compound premises of shurbs, plants, jungles etc.by cutting and removing as directed (Specific permission ofEngineer-in-Charge prior to execution will be necessary).(Payment to be made on area cleared)

Supplying, fitting and fixing bib cock or stop cock. Chromium plated Bib Cock short body (Equivelent to Code No.511 & Model- Tropical /sumthing special of ESSCO or Similar brand).

Chromium plated Stop Cock (Equivelent to Code No.513(A) & 513(B) Model- Tropical /sumthing special of ESSCO or Similar brand).

PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or equivalent)15 mm

Supplying, fitting and fixing shower of approved brand and make. PTMT overhead shower (prayag or equivalent ) 150 mm round .

Supply of Chlorinated Polyvinyl Chloride (CPVC ) pipes &fittings conforming to IS-15778: 2007 (Q) Ball Valve 25 mm

(Q) Ball Valve 32 mm

(Q) Ball Valve 50 mm

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) P.V.C Pipes. 15 mm dia.

P.V.C Pipes. 25 mm. dia.

P.V.C Pipes. 32 mm. dia.

P.V.C Pipes. 50 mm. dia.

Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. Specification with P.V.C. fittings complete, C.I. brackets including two coats of painting to bracket etc.

Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. Brackets on 75 mm X 75mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30mm dia, approved quality P.V.C.waste pipe with C.P. nut 32mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P.nut including mending good all damages and painting the brackets with two coats of approved paint. 550 mm x 400 mm size.

Supplying, fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of C.I. brackets. Sink only. 530mm x 430mm x 180mm.

Supplying, fitting & fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P.nut, 15mm dia. 900 mm long.

Supplying, fitting and fixing approved brand 32mm dia P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps. 1050mm long.

Supplying, fitting and fixing pillar cock of approved make. PTMT Pillar Cock-15 mm. (Prayag kor equivalent).

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 . Single socketed 3 meter length. 75 mm.

Single socketed 3 meter length. 110 mm.

Fittings. Bend 87.50 110 mm

Fittings. Pipe Clip. 110 mm

Fittings. Door Tee. 75 mm

Fittings. Door Tee. 110 mm

Fittings. Plain tee. 75 mm

Fittings. Plain tee. 110 mm

Fittings. Cleaning pipe. 75 mm

Fittings. Cleaning pipe. 160 mm

Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any foor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Enginer-in-charge) Payment will be made on centre line measurement of the total pipeline including specials.). Above ground. 75 mm dia.

Above ground. 7110 mm dia.

Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. With 'P' trap.

Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing). 530 mm X 410 mm.

Supplying, fitting and fixing Flat back urinal (half stall urinals) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. 470 mm X 280 mm X 340 mm.

Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws supplied, fitted and fixed complete. E.W.C. . Plastic (hallow type) white.

Supplying, fitting and fixing 32 mm dia. flush pipe of approved make with necessary fixing materials and clamps complete. Polythene Flush Pipe.

Supplying, fitting and fixing urinals flush pipe fittings of approved brand. C.P. urinals flush pipe fiitngs range of one .

Supplying, fitting and fixing bevelled edge mirror 5.5 mm thick silver red as per I.S. 3438/1965 together with brass C.P. hinges. 600 mm X 450 mm.

Cleaning silt of inspection pit.

Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only). (iii) 65 mm dia

(iv) 50 mm dia

(v) 40 mm dia

Supply of G.I. nipple standard 50 mm long (vii) 65 mm dia

Supply of G.I. union (vii) 65 mm dia

Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (A) For Exposed Work (g) (ii) 65 mm dia. medium quality

(f) (ii) 50 mm dia. medium quality

(e) (ii) 40 mm dia. medium quality

Add GST @ 18%

Add Labour Welfare Cess @ 1%

Please Enable Macros to View BoQ information