CA NO CWE/AMB/NORTH-09 OF 2025-26 SPECIAL REPAIRS TO MD ACCN BLOCK NO 30/1-8 AT RACE COURSE AND ADDN/ALTN TO BLDG NO P173 AND P174 OF MR FOR GE (NORTH) AMBALA CANTT

Amount

M & L for taking down cement of cement lime plaster of any description on brick or stone walls etc including ranking out joints hacking for key scrubbing down with water etc complete all as specified and as directed.

Material and Labour rendering 15 mm thick on outer faces of brick work or concrete surfaces in cement mortar 1 :4 including finished even and smooth mix with WPC @ 2% wt of cement (WPC Paid separately) complete all as specified and directed .

M&L 15mm thick rendering in CM (1:6) to brick/Conc wall surface finished to even & smooth w/o using extra cement .

M&L 5 mm thick rendering in CM(1:3) to ceiling finished even and smooth complete all as specified and as directed by engr-in-charge

Supply only Integral waterproofing compound complete.

Demolition of Brickwork built in cement mortar including all quioins, arches, pillars etc complete all as specified and as directed.

M & L for brickwork with subclass `B` bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge

Discription as per aove item except bricks , using bricks retrived from item No.7 complete all as specified and as directed by engr-in-charge.

Demolition of Cement concrete (Unreinforced) of any description in ground floors and pavings n exe 15 cm thickness (below or above ground level) complete all as specified and as directed.

M & L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in bedding layer under floor surface finished even and fair complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premise complete all as specified.

M&L for 300x600x7mm thick coloured glazed tiles as in dado over 10mm thick rendering in CM (1:4) set & jointed in neat cement slurry & pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed

M&L for joint free Non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exc 0.11 but not exc 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match laid over 15mm cement screed bed in CM (1:4) complete all as specified.

M&L for joint free ceramic coloured tiles 7 mm thick (square/ rectangular) area of each tiles exc 0.18 but not exc 0.38 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match laid over 15mm cement screed bed in CM (1:4) complete all as specified.

M&L non skid ceramic coloured tiles 7 to 8 mm thick joint free cut from tile of area exc 0.18 Sqm but n.exc. 0.38 Sqm as in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick screed in cement motar 1:4 complete all as specified.

M & L for machine cut kota stone slab flooring of size 550mm x550 mm 18-20mm thick over cement screed base 10mm thick of CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by the Engineer-in-Charge

M & L for kota stone slab of size 550mm x550mm of 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed base 10 mm thick of CM(1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by the Engineer-in-Charge

M&L for granite (of any type) tiles 20mm thick machine cut one piece in width and length not less than 1.8M(except in case of slab is more than 1.80M and less than 2.40M smaller size as approved by Engr-in-Charge may be used) table rubbed & polished as in cooking platform/window cills etc including 15mm thick bedding layer in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble incl rounding of front edge and finally granite finish polishing with and including taking down the existing covering all as specified and as directed.

Demolition, Cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L, 75 mm thick PCC (1:3:6) C-2 using 40mm graded stone agg in path/plinth protection finished even & smooth completed W/O using extra cement.

M&L PCC (1:3:6) C-1 using 20 mm graded stone agg as in surface channel or drain incl use of necessary from work for fair finished surface.

Extra for forming fair finished drain or channel 45 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each complete all as specified and as directed by the Engineer-in-Charge

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sq. m but not exc 4 sq. m each complete all as specified and as directed by the Engineer-in-Charge

S & F bands, straps, supports or stay for rainwater, ventilating pipes, including bolts, if required; hooks(stay), heavy, for large gates, hooks and pintle hinges; larger hasps and staples; chains; hand made slidinfg bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain anle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe 410-0 or Fe 310-0 complete allas specified and as directed by the engineer-in-charge.

M & L for cutting holes in exc. half brick but not exc. one brick thick walls, built in mud mortar, for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B1 as required (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall) complete all as specified and as directed by the Engineer-in-Charge

S&F factory made single extruded WPC(Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60( suspension grade),calcium carbonate and natural fiber(wood powder/rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100gms) having minimum density of 650kg/cum and screw withdrawal strength of 1800 N(face) & 900 N(edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistence to spread flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with neccessary full body threaded star headed counter sunk SS screw, all as per direction of Engineer-in-charge.(Note: stainless steel butt hinges and necessary SS screws shall be paid separately) complete all as specified and as directed by the Engr-in-Charge.

S&F factory made single extruded WPC (Wood Polymer Composite) glazed and skeleton shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-in-Charge. (Note: stainless steel butt hinges and necessary SS screws shall be paid separately) complete all as specified and as directed by the Engr–in–charge.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size 45 x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant complete all as specified and directed.

S&F factory made single extruded WPC(Wood Polymer Composite) solid door/window/ceosetory windows and other frames / chowkhts of size 65 x 125mm comprising of virgin polymer of K value 58-60( suspension grade),calcium carbonate and natural fiber(wood powder/rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100gms) fabricated with meter joints after applying PVC solvent and screwed with full body threaded star headed SS Screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (face)& 1100 N (edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistence to spread flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant complete all as specified and directed.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virginpolymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicityindex of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face)& 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 andresistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of requiredsize with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge.

S&F double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutter fabricated from following sections :– (a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces. (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf. (c) Vertical mullion shall be ERW hollow T –section of size 60 x 25 mm made from 1.25 mm thick MS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape– 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt stove enamelled 150mm long– 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square – 01 No per leaf vi) Pintal hinges 12 x 75 mm – 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c welded to frame. (viii) Two coat of Synthetic enamel paint over one coat of red oxide primer. (ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws . (x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window. (xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B–1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessoriries as mentioned above. (iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type.

S&F steel windows or ventilators ,fixed type,with glazing bars complete all as specified and as directed by engnr-in-charge

S & F for galvanized mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and as directed.

S & F 200mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing for ISI Marked 125mm long aluminium handle, cast type, anodized complete all as specified and as directed.

M & L for 3.00mm thick tinted glass for windows and ventilators complete all as specified and as directed by the Engineer-in-Charge

S & F 300mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed by the Engineer-in-Charge

S&F 150 mm MS ordinary rat tail rod pattern springs incl roller and roller plate fixed to wooden chwkhats or welded to angle iron door frames.

Supply and fixing for butt hinge ISI Marked 100mm size, medium weight, cold rolled mild steel complete all as specified and as directed.

Supply and fixing for stainless steel butt hinge ISI Marked 100mm size, medium weight, cold rolled complete all as specified and as directed.

S&F small articles such as door stoppers etc of IInd class H/Wood. Incl all necessary labour area not exc 200 cu cm each.

S & F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

M & L for taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

S & F for ISI Marked 15mm bore medium grade GI tubing with all fittings complete all as specified and as directed.

M & L for taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

M & L for 20mm bore `Medium grade` galvanised tubes with all fitting, laid in trenches complete all as specified and as directed by the Engineer-in-Charge

M & L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in brick walls complete all as specified and as directed by the Engineer-in-Charge

S & F in repair of ISI marked 15mm bore angular stop cock, brass chromium plated screwed down, high pressure, with crutch or butterfly handle, complete all as specified and as directed.

S & F in repair of ISI marked 15mm bore stop valve, brass chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed.

S & F in repair of ISI marked 20mm bore stop valve, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed.

S&Fin repair, 15mm bore stop valves chromium plated fancy type chromium plate with long shank & cup (concealed type). Complete all as specified and as directed by engr-in-charge.

Supply and fixing in repair for ISI marked 15mm bore bib tap of Brass chrome plated long body, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S & F in repair of ISI marked Pillar Tap of 15mm bore dia, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F in reapir 125mm dia swivel shower of brass chromium plated any colour for fixing with 15mm pipe (minimum weight 40 gms).

S & F in repair of 15mm size PVC connections with PTMP nuts of length 450mm complete all as specified and as directed by the Engineer-in-Charge

S&F in repair vitreous chinaware squatting pan white ORISSA pattern size 580x440 mm with integral foot rest, 100 mm Cl ‘S’ or ‘P’ trap, front or back inlet including providing lime conc. Bedding & making necessary connections comp.

Supply and fixing in repair 10 ltrs capacity PVC Valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed by engr-in-charge

S&F in repair vitreous china wash hand basin flat back white in colour with pedestal ISI marked of size 550mm x 400mm with brass chromium plated waste coupling and PVC waste pipe fixed to walls with CI breckets 2 Nos embedded in CM 1:4 complete all as specified and directed by Engineer-In-Charge.

M & L for dismantling water tanks exc 250 but not exc 500 Litres, and removing to store complete all as specified and as directed by the Engineer-in-Charge

S&F 500ltr capacity PVC water storage tank rotational moulded (cylenderical verical with closed top) hoisted & fixed in position incl 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe & fixed.

S & F of 100mm bore branch pieces, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed by the Engineer-in-Charge

M & L in repair 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge

M & L for PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge

M & L prepration of newly plastered surface of wall and applaying two coats of acrylic distemper with roller over a coat of 2mm thick wall putty on plastered surface.Complete all as specified and as directed by Engr-in-Charge.

M & L prepration of newly plastered surface of wall and applaying two coats of cement base paint over a coat of cement based primer on plastered surface complete all as specified and as directed by Engr-in-Charge.

M&L preparation of newly plastered surface of ceilings and applying three coats of white wash complete all as specified and as directed.

M & L prepration of previously plastered or unplastered surface of wall and applaying two coats of acrylic distemper with roller over a coat of 2mm thick wall putty on plastered surface.Complete all as specified and as directed by Engr-in-Charge.

Complete removal of existing treatment including washing rubbing down and stopping of distempered and painted surfaces and applaying two coats of white wash on ceiling surface .Complete all as specified.

Complete removal of existing treatment including washing rubbing down and stopping of distempered and painted surfaces and applaying two coats of cement base paint on wall surface .Complete all as specified.

Preparation of new or previously untreated surfaces of any description over 10cm width or girth not other wise described applying two coats synthetic enamel paint over a coat of red oxide zinc crome to steel surfaces.

S&F in repair 25 mm dia 1.6 mm thick Stainless steel decorated type curtain rod incl pair of MS bracket,finials (latto) at ends inc fixing on wall with screws

Supply & Fixing in repair stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm, complete all as specified

Dismantling Brick tiles or terracing tiles, single layer on roofs complete all as specified and as directed.

Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and as directed.

M & L for providing cement concrete 1:2:4 Type B1 using 20mm graded aggregate as in roof kerbs or mud stops,padding, rounded or chamfered on edges complete all as specified and as directed.

M & L Priming roof surfaces and applying water proofing treatment over roofs comprising of the following,Complete all as specified & as directed:- (i) Applying oil bound bitumineous primer at the rate of 0.40 Liters/Sqm as per IS 3384-1986 on prepared surfaces.Surface shall be kept free till the moment, the primer is impregnated and the solvent oil in primer is evaporated. (ii) Laying 3mm thick APP polymeric water proofing membrane of weight not less than 3.6 Kg/Sqm, black finished reinforced with non woven polyster matt, with a thermo fusible finish,torching overlaps with a propane or butane gas torch, with a overlap of 75mm at sides and 100mm at the ends,and sealing including applaying a coat of cold emulsion bitumineous primer all as per manufacturer's instruction including prepration of surface. (iii) Applying one coat of hot straight run bitumin grade 30/40 (Grade S-35) confirming to IS -73 at the rate of 1.2 Kg/Sqm. Note:- The water proofing treatment shall be carried out by manufacturer or his authorized applicators in terms of clause 11.43 of MES Sch Part-'I' (2009)

M&L cement concrete tiles 30 cm x 30cm x 20 mm thick, machine pressed laid on screed bed and joints grouted flush in CM (1:3) mixed with 5% crude oil by weight of cement including screed bed 15 mm thick in cement mortar 1:6 complete all as specified and as directed by the Engineer–in–Charge.

Demolition of of rein forced Cement Conc of any description & in any position comp incl cutting of reinforcement.

M & L for formwork to chullah hoods, chajjas, weather shades, corbels, water troughs and similar items including edges, work in rough finished flat surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge

M & L for mild steel TMT bars of 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge

M & L for RCC 1:2:4 type B0 using 12.5mm graded aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports overhangs etc, also splays between floors and beams, etc., work in rough finished flat surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised., width of flaps when open in 30mm complete all as specified and as directed by the Engineer-in-Charge

S&F Aluminium CP fancy type handle 100mm size complete all as specified and as directed by the engineer in charge.

S & F brass body ball catches with 8mm dia steel ball and striking plate including letting in complete all as specified and as directed by the Engineer-in-Charge

M & L for 100 mm thick cement concrete type D-2 1:4:8 using 40mm graded aggregate complete all as specified and as directed by the Engineer-in-Charge

M & L for providing PCC 1:1.5:3 type B1 using 20mm graded aggregate as in kerb stones, (of Size 0.30 X0.30m X 0.10mm), with plain fair faces, including chamfers, weatherings, throating etc. and set in CM 1:4 complete with joints to match complete all as specified and as directed.

M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with Grey cement and no pigment over 25mm thick sand layer complete all as specified and as directed.

M & L for taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed by the Engineer-in-Charge

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls complete all as specified and as directed by the Engineer-in-Charge

S & F in repair of 75mm bore bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed by the Engineer-in-Charge

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls complete all as specified and as directed by the Engineer-in-Charge

S & F 75mm bore PVC (SWR) vent cowl, complete all as specified

S & F in repair of 110mm bore bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed by the Engineer-in-Charge

M & L in repair for soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed by the Engineer-in-Charge

M & L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel(1/2 round 3/4 section) in cement concretye 1:2:4 type B-1 smooth finished, and reforming benching as required for 100mm bore pipe line complete all as specified and as directed by the Engineeing-in-Charge.

S & F bands, straps, supports or stay for rainwater, ventilating pipes, including bolts, if required; hooks(stay), heavy, for large gates, hooks and pintle hinges; larger hasps and staples; chains; hand made slidinfg bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain anle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe 410-0 or Fe 310-0 complete allas specified and as directed by the engineer-in-charge.

M & L for PCC 1:5:10 Type E2 using 40mm graded aggregate as in filling in sunken portion floor ,rounded or chamfered on edges complete all as specified and as directed.

M&L for sunken floor water proofing treatment complete all as under :– (A) Scrapping the surface with wire brush and cleaning with water and allow to dry. (B) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound. (C) 15 mm thick cement plaster 1:3 mixed with water proofing compound as per manufacture instruction (the corner will made rounded in concave shape). (D) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound. (E) Apply one coat of hot bitumin grade 85/25 conforming to IS 702 @ 1.2 kg/sqm. (F) Supply and laying APP with non woven polyster reinforced sheet 3mm thick weight not less than 3.00 kg/sqm. (G) Applying one coat of hot blown bitumin grade 85/25 conforming to IS–702 @1.20 kg/sqm. (H) Curing the sunken portion with water min 48 hours by ponding. (J) Fixing 50mm bore GI pipe medium grade as in spout of 0.60 mtr length in each sunken.

Supplying & Fixing in repair for stainless steel plate rack standard size 786mmx914mm x 264mm complete and fixing with rawl plug and steel screws of wt not less than 8 kg each, complete, all as specified and as directed. Make :– Bluestar /Nirali /Prayag.

Supply and fixing of 18mm thick PVC sheet (density not less than 600 Cum) having one side decorative laminated sheet all required brackets SS screws etc. the panel shall be fabricated using adhesive and screws where ever required.all the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification including dismanteling existing board any type complete all as specified and directed. NOTE: - Material manufacture test certificate alongwith purchase voucher should be produced before execution of work.

S&F as in repair mild steel door shutter two leaves with frame of 20 gauge MS sheet (all around) and leaves of 21 gauge MS Sheet (all as per godrej pattern) with three way locking arrangement with brass lock with duplicate key and CP handle including two coats of spray painting over a coat or red oxide primer complete fixed in existing cupboard fixed with necessary nuts, bolts including embedded in PCC 1:2:4 (area of opening shall be measured) complete all as specified and as directed by the Engineer–in–Charge.

Excavating in post holes (or similar holes) each not exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance not exc 50m and making good surface, work in soft/loose soil, complete all as specified

M & L for PCC 1:3:6 Type C2 using 40mm graded aggregate as in foundations, filling inside hollow pipes placed vertically up to 6 mtr height complete all as specified and as directed.

M & L for PCC 1:1.5:3 Type B2 using 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

S & F steel work in tubular trusses square or rectangular including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and as directed by the Engineer-in-Charge

S & F 250/300 mm dia MS structural hollow pipes on supports placed vertically steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and as directed by the Engineer-in-Charge

S & F for rolled mild steel in plates channels (plain or chequered), square cut or notched (ordinary and counter sunk) forming holes, without any attachment, of quality GDE Fe 410-S complete all as specified and as directed by the Engineer-in-Charge

S & F 11-15mm dia of shank mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and as directed by the Engineer-in-Charge

S & F for Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified.

S & F for Pre-painted galvatume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified.

M & L for PCC 1:4:8 Type D2 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in soft/loose soil, complete all as specified

M & L for removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil, complete all as specified

M & L for hardcore of broken bricks exc 63mm but n exc. 100mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rolled/rammed to a true surface complete all as specified.

Material and labour for premium quality, glazed coloured ceramic tiles 450x350x7mm thick on vertical surfaces of walls , SKIRTING / DADO over and including 10mm thick rough finished plaster in cement mortar (1:4) set jointed in neat cement slurry and pointed in coloured cement to match complete, all as specified and as directed.

S & F for rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, quality confirming to GDE Fe410-S complete all as specified and as directed by the Engineer-in-Charge

S & F 35mm thick, 2nd class HW, plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed by the Engineer-in-Charge

S & F 150mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

S & F 250mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed by the Engineer-in-Charge

Preparation of new wooden surfaces of any description over 10cm width or girth not other wise described applying two coats synthetic enamel paint over a coat of pink primer.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, regulators, socket outlet, etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and as directed.

Taking down and refixing of water heater any type and any size/capacity with all accessories such as nut bolt washers ,PVC pipe etc with making all connection using three core copper conductor flexible cable drawn through in PVC flexible conduite pipe complete all as specified and directed.

Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly (boxes shall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally) including provision of new covered plate over sunken box for housing the modular switches , modular socket outlets,modular fan regulators etc. for one light/fan/exhaust fan/bell point controlled by one way switch, complete all as specified and as directed by Engineer-in-Charge. Note :- a) .All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid for separately .

Description all as per serial item No.129 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on same board, complete all as specified and as directed by Engineer-in-Charge.

Description all as per serial item No.129 here-in-before but for One light point controlled by two, two way switches complete all as specified and as directed by Engineer-in-Charge. .

Description all as per serial item No.129 here-in-before but for one socket outlet 5 Amp with 2.50 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade, ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly complete all as specified and as directed.

Description all as per serial item No.129 here-in-before but for one socket outlet 16 Amp with 2.50 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade, ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly complete all as specified and as directed.

Description all as per srl item No 129 here-in-before but for one socket outlet 16 Amp with 4.00 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 4.00 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly complete all as specified and as directed.

Supply and fixing of modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular switch 1 module, single pole, one way 16 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular switch 1 module, single pole, two way 6 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular bell push 6 Amp, 1 way, 1 module, 230 volts complete all as specified and as directed.

Supply and fixing of modular socket outlet 2/3 pin combined, 6 Amp, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular socket outlet 3/3 pin combined, (6pin), 6/16 Amp, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing as in repair electronic Fan regulator modular 100 watt, 1 module, 230 volts , 50 Hz, AC supply suitable for ceiling fan any type/make/sweep complete all as specified and as directed.

Supply and fixing ceiling rose surface type 2/3 terminal polycarbonate, isolated body complete all as specified and as directed.

Supply and fixing in repair calling bell ding dong 230 volt, complete all as specified and as directed.

Supply and fixing in repair LED batten fitting 18-20 watt, 4 feet, aluminium housing with electronic driver cool/warm type industrial model complete, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed. Cat part No. LUMILINEPLUSNEOBS20WLED830SPCSSIND of make Havells or equivalent in make given in Appx 'B'.

Supply and fixing in repair, LED surface mounted bulk head luminaries 8-10 watt with min 800 lumen, industrial model, IP 65, aluminium housing, surge protection including driver and LED lamp, etc. complete with all accessories, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed. Cat part No. HEXAFT10WLED857SSYMBOPC of make Havells or equivalent in make given in Appx 'B'.

S&F Surface mounted wall Mirror LED light Compact & sturdy 10 watt LED decorative fixture with anti glare polycarbonate diffuser, multi purpose lighting solution& applications .all accessories & fixtures, internally prewired and connecting by provding copper flexible wire 23/.0076 mm twin core upto fitting, complete all as specified and directed. Cat part No. LUMILINE+ BS10WLED865PCSS of make Havells or equivalent in make given in Appx 'B'.

Supply and fixing in repair, 9/12 watt LED light fitting PVC wall mounting fixture (sketch type) including B-22 LED lamp compact and energy efficient epoxy powder coated luminaire and connecting with copper conductor flexible cable from ceiling rose to connector of the light complete including removing unserviceable light fittings complete all as specified and as directed. Cat part No. HLWB-01-B22 of make Halonix or equivalent in make given in Appx 'B'.

Supply and fixing in repair, LED Bldg Security Light Fittings of capacity 20 -25 watt made up of die cast aluminium housing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver and making electrical connection, service bracket of mild steel pipe 25 mm bore medium grade of length 0.70 mtr fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts and washer and suitable reducer for connecting fitting to GI pipe as required at site including two coats of synthetic enamel paint over one coat of red oxide primer on mild steel work complete complete all as specified and as directed. Cat part No.ENDURASUNDOWNSL25WLED765PASYBOTGIHD of make Havells or equivalent in make given in Appx 'B'.

S&F single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB.20 Amp, 10 KA 'B' curve including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811955 of make Indo Asian or equivalent in make given in Appx 'B'.

Supply and fix sheet metal enclosure Vertical triple pole & neutral(VTPN) IP-54 including MCCB 100 Amp, 16 KA, 415 volts, 4 way with 200 Amp rated bus bar flush /surface mounting double door duly grouted in solid block wall or on wooden board in and including lugs/thimbles duly crimped for connection including making smooth the disturbed surface including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811882 of make Indo Asian or equivalent in make given in Appx 'B'.

Supply and fix sheet metal MCB DB SPN 8 way with 200 Amps rated bus bar single pole and neutral with double door IP-54 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811825 of make Indo Asian or equivalent in make given in Appx 'B'.

Supply and fix MCB SP, 6-32 Amps, 240 volt,10 KA , 'B' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed.

Supply and fix MCB SPN 32 Amps, 240 volt,10 KA , 'B' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed.

Taking down and refixing only ceiling fan after cleaning in any model/size etc and making all connection using three core copper conductor flexible cable in size 1.5 sqmm including drawn through PVC flexible conduit pipe from ceiling rose to fan connector complete all as specified and directed.

Taking down and refixing only exhaust fan after cleaning in any model/size etc and making all connection using three core copper conductor flexible cable in size 1.5 sqmm including drawn through PVC flexible conduit pipe from ceiling rose to fan connector complete all as specified and directed.

Taking down and refixing of serviceable electronic energy meter 5 to 30 Amps capactiy obtained under above item complete all as directed.

S & laying as in repair sub main wiring with two run of 6 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium grade ISI marked of adequate size for housing the wires complete all as specified and as directed. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to earthing test point as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/c both ways with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing as in repair complete all as directed by Engineer-in-Charge and earth testing on completion .

Note:- Amount of credit of Rs. 68,688.00 for retrieved materials is mentioned in Schedule of Credit Page No. 24 & 25 of tender documents in pdf form which will be deducted offline while acceptance of tender.

Peerzada And Sons (BID ID -3344102)