Development of various Tourist facilities for Puliyancholai Falls in Trichy District

Amount

Clearing and Removing of Heavy Jungle clearing away from the site and levelling the site etc. complete as directed

Earthwork excavation for foundation in all soils except hard rock requiring blasting to a full depth with an initial lead of 10m and lift of 2m in hard stiff clay,stiff black cotton,hard red earth mixed with small size boulders etc.,complete complying with relevant standard specification.

Supplying and Filling in foundation and basement with P-sand in layers of 150mm thickness well watered rammed and consolidated complete complying with relevant standard specification.

Supplying and filling in foundation and basement excavated earth soil in layers not more than 16cm thick well rammed watered, consolidated and compacted etc., complete complying with relevant standard specification.

Cement Concrete 1:5:10(One Cement five sand ten aggregates) using 40mm gauge HBG jelly inclusive of shoring strutting and baling out water where ever necessary ramming curing etc., complete in respects complying with relevant standard specification and as directed by the Department Officers.

Plain Cement Concrete 1:2:4 (one cement, Two sand and Four hard broken stone jelly) using 20mm jelly including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Damp Proof in cement mortar 1:4, (one cement and four sand) 20mm thick mixed with Impermo powder 2% by weight of cement ect., complete complying with relevant standard specification.

Brickwork in Cement Mortar 1:5 (One cement and five sand) using IInd class chamber burnt bricks of size 9"x4½"x3" including cost and conveyance of all materials and labour charges and all other incidental charges etc.,complete complying with standard specification.

a) Upto For Basement

a) In Ground Floor

Brick partition wall in Cement Mortar 1:3 (One cement and three sand) 11.40 cum. thickness using II class chamber burnt bricks of 9” x 4 ½” x 3” including both side plastering with CM 1:5, 12mm thick and using hoop iron with reinforcement if found necessary etc. complete. a) In Ground Floor

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers.

a)Upto Basement

b) In Ground Floor

Supplying fabrication and placing in position of MS (or) Rts bars for all RCC works including cutting bending placing and cost of binding wire etc.,complete complying with standard specification.

Centering for soffits of RCC slabs of plane surface like lintels, beams,stair waist slabs & landing slabs ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X '3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed by the corporation officers.

a) Column Footing and Plinth Beam

b) Plain Surfaces Beams, Roof slab

c) Centering for Sunshade and Rectangular Column

Special ceiling plastering for R.C.C slab beam and sunshades with cement mortar 1:3 ,10mm thick including tacking finishing neatly, cost and conveyance of all materials and all labour charges,curing etc., complete complying with standard specifications.

Plastering with Cement Mortar 1:5 (One cement and five sand),12mm thick including cost and conveyance of all materials and all labour charges,curing etc., complete complying with standard specifications.

Weathering course concrete with broken jelly 20mm size and pure slaked lime over RCC roof slab,the proportion being 32:12.5 for required depth of 80mm for giving required slope and thickness of roof on required ,well beaten with wooden beater etc.,complete complying with standard specification.

Finishing the top of roof with one course of machine pressed tiles of size 23cmx23cmx20mm of approved quality laid in 1:3,12mm thick mixed with water proofing compound 2% by weight of cement used etc., complete with standard specification

Supply and fixing M.S.Grill for Window of approved design including welding,transporatation and one coat of primer etc., complete complying with standard specification.

Supplying and fixing Teak Wood Frames for DOORS, WINDOWS, VENTILATORS and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc., complete in all floors complying with standard specification.

a) Upto 2m in Length

b)2m to 3m in Length

Supplying and fixing in position of 30mm thick Solid core flush shutters with Teak wood ply on both sides with teak wood lipping alround including cost and conveyance of all materials,Aluminium furniture fittings including labour charges for fixing in position of door shutter etc., complete complying with standard specification.

Supply and fixing in position of UPVC ventilator of any size .The outer frame will be 62x38x2mm 21.17Kg/m and the louvers with moving arrangements will be made with Aluminium,channel of size 60x30x4mm @ 1.27kg/m with necessary glass pans for louvers 4mm thick Alulminium clips 19.05x17.27x11.05x0.075mm @0.169kg/m including all materials,labour and power consumption charges required fro fabrication if necessary chipping dismantling making hole sing RCC columns,beams or masonary whereever necessary with power drill to the extent required and make good to the original conditions.

Supplying, fabrication and fixing of 30mm thick both side pre laminated WPC door shutter with frame of required size 0.75m x 2.00m & 0.90 x 2.00m including necessary brass furniture fittings such as 125mm x 25mm brass hinges-3Nos , 200mm x 12mm brass tower bolt - 1No, 150mm x 12mm brass tower bolt - 2Nos,150mm brass handle - 2Nos, cylindrical lock - 1No, T.W lippings around the shutter etc., including cost, conveyance of all materials and labour charge for fixing complying with standard specification.

Flooring with Anti Skid ceramic tiles of approved quality, colour design and of size 30cmx30cm laid in cement mortar 1:3 (One Cement and Three Sand) 20mm thick including pointing the joints with same colour cement to the full depth of the tiles including cost and conveyance of all materials and labour etc. complete complying with standard specification.

Dadooing the side walls with glazed wall tiles of approved quality colour, design and of size 30cm x 45cm in cement mortar 1:2 - 10mm thick and painting with white cement including finishing the joint and polishing the tiles surface glassy etc.complete complying with standard specification.

Supplying and fixing in position best quality approved make, colour glazed Earthenware wash hand basin oval shape of size 550x400mm in granite table top including cost of 15mm brass chromium plated pillar cock 32mm dia CP waste coupling with rubber and chain, 15mm dia CP angle valve, 15mm dia brass nipple, 15mm dia Nylon connections including fixing the wash in position with a pair of M.S. angle 50x50x6mm etc. Complete as per standard specification.

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Supplying and fixing in position Indian water closet of size 580x440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap conforming to IS 2556-Part XII with 10 lit capacity PVC flush tank and internal fittings with sand cushion and forming, flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to case iron soil pipes by dismantling brick masonary, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without quality with 'P' trap or 'S' trap conforming to IS:2556 leakage etc., complete complying with standard specifications.

Supplying and fixing in position Indian make white glazed earthernware Magnum urinal of ISI standard and best approved colour urinal of best approved quality with G.I.pipe connection of 32mm, bell mouthed, waste Pipe, 15mm. dia G.M. Gate value bring the urinal to the wall in position with necessary T.W.Plugs, clamps, shellac etc., including dismantling masonry if necessary and readoing the same to original condition fixing the 15mm. dia G.I.pipe and wheel valve. Painting the pipe with two coats of approved paint over one coat of primer and checked without any breakage complete complying with standard specification.

Supplying and fixing 50mm thick (both side polished) marble slabs for shelves (4 tier) with neat finishing. The rate inclusive of cost of slab and labour charges for fixing etc., complete as directed by the departmental officer.

Supplying and fixing of CP screw down tap heavy type 15mm dia including testing for leakage etc., complete complying with standard specification.

Supply and fixing of Health faucet of approved quality and make including fixing in position etc., complete as directed by the Corporation Officers.

Supply and fixing 4” dia PVC Nahini trap of size with C.P. Gratings 100mm x 75mm of approved quality etc. complete as directed by the Corporation Officers.

Supplying, laying and jointing of following size of CPVC pipes of approved make and ISI quality including fixing CPVC specials but excluding cost of CPVC specials,cutting, threading of pipes concealing the pipes into wall with necessary clamps and nails , dismantling the wall, laying pipes and making good the dismantled portion to original condition with necessary brick work and plastering wherever necessary etc.complete complying with standard specification

a) 25mm dia pipe

b) 20mm dia pipe

Supplying, laying and jointing of following size of PVC pipes of approved make and ISI quality including fixing PVC specials but excluding cost of PVC specials,cutting, threading of pipes concealing the pipes into wall with necessary clamps and nails , dismantling the wall, laying pipes and making good the dismantled portion to original condition with necessary brick work and plastering wherever necessary etc. complete complying with standard specification

a) 40mm dia PVC pipe

b) 50mm dia PVC pipe

Supplying and fixing of 75mm dia P.V.C pipes 6Kg/Sqm of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs, PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.Above ground level upto 4m height.

Supplying and fixing of 110mm dia P.V.C pipes 6Kg/Sqm for Sanitory line of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs, PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.Above ground level upto 4m height.complete complying with standard specification

Supply & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes etc., complete. as direcetd

Supply and fixing the following GI and PVC pipes and CPVC specials for pipe connection arrangements for inlet outlet sour and overflow etc., including cost of pipes specials valve labour charge fro lifting aligning ,cutting,threading,fixing and painting of GI pipe with two coats of approved quality enamel paint etc.complete complying with standard specification

25 mm Dia CPVC Elbow

25 mm Dia CPVC Tee

25 mm Dia CPVC coupling

25 mm Dia CPVC Union

20mm Dia CPVC Elbow

20mm dia CPVC Tee

20mm dia CPVC Union

20 & 15mm dia CPVC elbow

75mm dia PVC Plain elbow

75mm dia PVC Door Elbow

75mm dia PVC Door Tee

75mm dia PVC Tee

110mm dia PVC Door Tee

110mm dia PVC Bend

110mm dia PVC Cowl

Supplying and fixing of 20mm dia Brass ball valve GM gate values, GI fittings, pvc specials of various sizes of approved quality and ISI band as per standard specification

Construction of manhole chamber of size 600x600mmx1100mm (above GL 200mm Below GL 900mm) to total height of 1100mm (ID) 200mm above ground level 900mm below ground level with a base concrete of 100mm thick 1:5:10 over a sand cushion of 100mm thick. The chamber should be constructed in brick masonry 230mm thick in CM 1:5 with stock bricks of size 9"x41/2"x3". The inner side of chamber plastrering in cm 1:5, 12mm thock, the outer chamber of wall to depth of 300mm plastered in cn 1:5, 12mm thick. The Chaber top covered with SRF cover slap 100mm thick. The rate is includuing the cost of material,Labour etc, complete.xincluding all works of earthwork,CC 1:5,10, 200mm thick,Brickwork, plastering in CM 1:5,12mm thick etc., complete

Providing SS hand rails using in pathway of 304 grade 16 SWG SS pipes 40mm dia as verticals to height spaced at 1m centre with top railing 50mm dia and 25 mm dia pipe intermediate rigidly fixed with spacing of 0.30m centre to centre vertically in the existing concrete/brick wall structure and properly fixed including all materials and labour charges polishing transport charges etc., complete complying with standard specification

Painting two coats with Plastic Emulsion paint of approved quality and colour including one coat of emulsion primer over new wall surfaces including cleaning and preparing the surface, scaffolding etc., complete complying with standard specification

Painting two coats with Elesto metric acrylic water proof Exterior Emulsion paint ( Dr.Fixit or equivalent) over one coat of primer (Prime seal of Dr. Fixit or equivalent) after cleaning the surface over old wall surfaces including scaffolding etc., complete complying with standard specification

Painting two coats with Ready mixed synthetic enamal paint of approved quality and colour over new Iron surfaces including prepare the surfaces, cost of brushes and all materials, scaffolding etc.,complete complying with standard specification

Supply and erection of M.S Angle pole of size 50mmx50mmx6mm in the equired length including provision of anchorage clamp and making holes for fixing chain link fencing , erection in true alignment with necessary foundation concrete including cost and conveyance of all materials , labour but excluding the cost of concrete etc...complete complying with standard specification.

Supply and fixing of chain link fencing (50mmx50mmx10 Gauge) with necessary M.S angle post of size 50mmx50mmx6mm at every 3.0M centre to centre fixing in P.C.C1:2:4. The top and bottom to be fixed with M.S flat of size 25x3mm horizontally on both sides including provision of holes in M.S flats and fixing M.S bolt and nuts etc., complete. The rate is including cost of all materials, labour charges and excluding cost of M.S angle and P.C.C 1:2:4 etc., complete as directed.

Supplying and fixing of Duck spring rideon Charges including for cost of materials and painting etc complete as directed by the approved Corporation Officials

Supplying and fixing of standard double swinge which is made of M.S 3" round pipe for vertical & horizontal support with FRP seater. Charges including for cost of materials and painting etc complete as directed by the approved Corporation Officials

Supplying and fixing of circle swing standard which is made of M.S 3" round pipe for vertical & horizontal support outer frames and inner frames is made of M.S 11/2" round pipe with necessary aluminum sheet for seater. Charges including for cost of materials and painting etccomplete as directed by the approved Corporation Officials

Supplying and fixing of double seesaw chair seats which is made of M.S 3" round pipe for vertical & horizontal support with FRP seater. Charges including for cost of materials and painting etc complete as directed by the approved Corporation Officials

Supplying and fixing of metal slide . Outer frame of slide is made of by the 3" M.S round pipe, slide sheet is made of by stainless steel (Veda) and with necessary M.S ladder with handrails. Charges including for cost of materials and painting etc complete as directed by the approved Corporation Officials

Supplying and fixing of Merry go round four seats) which is made of M.S 3" round pipe for vertical support and 11/2" M.S round pipe around and M.S sheet for seater with M.S 1" handrails. Charges including for cost of materials and painting etc complete as directed by the approved Corporation Officials.

Supplying and fixing of rope climer which is made of M.S 3" round pipe for vertical and horizontal support and inner side are connected with ropes. Charges including for cost of materials and painting etc complete as directed by the approved Corporation Officials

Supplying and fixing of S type balance walk Charges including for cost of materials and painting etccomplete as directed by the approved Corporation Officials

Supplying and fixing of Horse spring ribeon Charges including for cost of materials and painting etc complete as directed by the approved Corporation Officials

Supplying and fixing in position of the Granite Stone Benches with seaters of Size 1.50 M length x 0.60m width x 0.10m thick and legs of size 0.90m height x 0.60m width x 0.10mm thick the rate is inclusive cost of all materials and labour charges etc complete as directed by the approved Corporation Officials

Providing and laying, spreading and compacting graded stone aggregate to Wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.

Supplying and laying interlocking Rubber Moulded Hydraulic Pressed Paver Block M40 grade 83mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, stone dust cushion 50mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers, sweeping tranporting loading unloading of laying paver block as per standard specification,. Natural grey colour

Manufacturing, supplying and fixing in position plain cement concrete precast kerb slab of size 300mmx450mmx125mm in Cement Concrete 1:2:4 (One cement, Two sand and Four jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, finishing, curing, fixing and pointing the slab with CM 1:3 (One Cement and Three Sand) to full depth of slab etc., complete complying with standard specification and as directed

Supply of miscellaneous MS bore materials suitable to 250 mm dia pipes as follows. Drilling pilot bore hole of size 250 / 300 mm at above village site in all starata by mud flush direct rotary rig (Mechanical) complete complying with standard specification

Reaming of 250 / 300 mm dia pilot bore hole to size 450 mm dia. including assembling, jointing, lowering of housing casing screen pipes & other assembly items with gravel packing and clay balls packing etc complete complying with standard specification

Upto 60 m depth ending below ground level

From 60 m depth and upto 90 mt depth ending below ground level

Development of bore by air compressor of 600 cfm / 150 psi capacity for minimum 06 hours or up to the availability of sand free discharge complete complying with standard specification

Supply of 250 mm dia ERW blank pipes complete complying with standard specification

Supply of 250 mm dia V wire screen pipes (ii) Size: 1.0 mm Regular complete complying with standard specification

Supply of miscellaneous MS bore materials suitable to 250 mm dia pipes as follows. Bore clamps made from MS plate with 03 holes on either side with nuts & bolts of standard make & suitable size. 750 mm x 75 mm x 16 mm complete complying with standard specification

Bore plug having 250 mm height made from MS plate of 5 mm thickness with 03 holes at equal distance on circumference for nut bolts type locking arrangement with nuts & bolts & lock nuts of standard make complete complying with standard specification

Bail plug having length of 0.45 meter from medium class pipe as per IS complete complying with standard specification

Steel bent plates of size 150 mm x 150 mm x 6 mm complete complying with standard specification

Supply of clay balls having size of 25 mm to 50 mm complete complying with standard specification

Electrologging of pilot bore Complete as directed

Water sample chemical analysis charges. Complete as directed

Supply and fixing of 2.00 HP Submersible Pump complete complying with standard specification

Supply and installation of FRP/PVC storage water tank with double flab cover of approved quality and make including conveyance and lifting to top of terrace and fixing in position etc., complete. In the tank, necessary holes to be made for inlet, outlet and over flow connections. The rate is including cost and conveyance of all materials and labour for erection etc. complete complying with standard specification

Supply and erection metal framed petro reflected information signage board of high intensity grade of following size made with 3mm thick alco panel sheet board fixed over the metal framed M.S angle frames made with ISA 40mm x 40mm x 6mm angles for all-round and intermediate frames at a spacing of not more than 0.75m on vertical direction and 0.60m on horizontal direction including fixing of petro reflected information signage letters over the alco panel sheet board. The sign board is to be erected with two numbers of ISMC 150 x 75mm vertical poles of 5.45m height with necessary foundation concrete of C.C. 1:2:4 using 20 mm HBG Jelly to a size of 0.60m x 0.60m x 0.90m. The rate is including cost and conveyance of all materials, painting the iron works with two coats of enamel paint over one coat of primer, erection of the signage board in true alignment in the location as directed by the corporation officers complying with specification.

Providing Turffing of Mexicon Grass. The existing soil to be removed filled with suitable to a depth of 75mm of Red soil and compost. The soil to be prepared by rough dressing, fine dressing and making grass mounts, After that fertilizer and Gypsum for neutralizing soil PH over the soil bed. The gross to be free from White Ants by applying pesticides like phorate and Monocrotophos. The chemical and mechanical weeds to be controlled by applying foliarspray.complete as directed

Supplying with mixture of red soil, River sand and FYM in 2:1:1 ratio after powdering, cleaning sieving opening of bags and filling with above mixture and arranging into beds etc.,complete as directed

Supply and fixing of bio- septic tank of 5000 litres capacity designed no foul smell, need less Space, Eco-Friendly and Hyglenic, More than 99 .9% Pathogens digested, It's odouries and gets rechycled water, No Maintenance for life time only one time feeding bio bacteria inoculum etc, complete with necessary erection work in an underground trench of size 6m x 3mx 3m. The Trench is to be constructed with a base foundation concrete in CC 1:5:10 using 40mm HBG Jelly with thickness of 150mm and alround brick wall of 23cm thick, plastering the wall with CM1:5 12mm thick, etc., The rate also including filling the trench with MSand after erection of the tank, provision for inlet chamber, transportation charges etc., as directed by the corporation officers.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade\in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator)

Wiring with 2 x 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with module GI switch box in flush with wall with 1 no 6A one way modle switch 1 no 6A 3/2 pin module socket with module front plate with painting of suitable colour with continuous earth wire connection of 1.5 Sq.mm copper wire for concealed PVC plug point.

Supply and Run of 2 of 2.5 sq.mm.(56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour

Supply and laying of 3 -1/2 x 35 Sqmm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and fixing of brass cable gland for 3 1/2 x 35 sqmm PVC LTUG aluminium armourd cable with earth connection

Supply and providing cable end termination of 3 1/2 x 35sqmm PVC LTUG aluminium armoured cable necessary aluminum cable sockets by crimping etc with eelctrical connection complete.

Supply and fixing of horizontal type 4 way triple pole neutral MCB distribution board in sheet steel enclosure double door type with metal door with IP43 protection with 40A 4 pole MCB isolator as incoming and 12 Nos 6A to 32 A SP MCB as outgoing inflush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB`s should be with the ISI mark.

Supply and fixng of TNEB meter board suitable for 3 phase 63A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 63A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 19/16 PVC insulated copper wire with earth connection complete.

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and installation of 22W 4 feet LED tube light fitting with its electrical connection etc., complete.

Supply and installation of 18W 2 feet LED mirror light fitting with its electrical connection etc., complete.

Supply and installation of 15W LED Bulkhead fitting with its electrical connection etc., complete.

Supply and fixing of 8" Brisk air ventillation exhaust fan with its electrical connection to make good condition.

Supply and laying of 4 x 16 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and fixing of brass cable gland for 4C X 16 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 4C x 16 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and fixing of 6 Mtr GI steel tubular pole for street light with base plate of (250 x 250 x 6mm) having dimension of 76.10mm OD x 3.65mm Thick x 6000mm Length, with 1 Mtr cross arm of 32mm GI pipe for fxing of 120 Watts LED Street light fitting with inbuilt of 10 Amps 4 pole MCB suitable and etc complete.

Supply and installation of Street light feeder pillar with 63A MCB incomer and 8 Nos 32A DP MCB with sheet metal enclosure - Weather proof type with inbuilt timer control All compontents covered with Hylem sheet of 12mm thickness with necessary bolts and nuts and with earth connection complete.

Supply and run of 2 of No.8 SWG GI wire for earth connection, including cost of all materials etc. all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

GST at 18%

BHAKIYA ASSOCIATES (BID ID -1435654)