JJM CWSS to Mavelikkara and adjoining Panchayaths Electromechanical works Pumps Transformer VCB Main Control Panel RMU etc in WTP at Mavelikkara and Raw Water Pump House at Mandapathinkadavu General Electrical Work

Amount

Appendix-A- Electromechanical Work-30 MLD WTP at Mavelikkara

OD79125/2023-2024:Supply Installation, testing and commissioning of 400KVA Unitised substation consisting of the following,11KV,high voltage panel board comprising of KSEB metering facilities with CT and PT,1No. Load break switch of 350 MVA capacity, Bus bar sections 350Amps capacity,3 Nos HT HRC fuses and with 230V shunt top coil. With copper winding, having a continuous rating for,11KV/433V 3 phase 50Hz.Vector group Dyn-11.USS should have cable end box on HV side suitable for 3Cx150Sq.mm XLPE cable and suitable end box for connecting 32Rx3.5Cx185Sq.mm Aluminium XLPE cable on LV side, with all fittings and accessories, complete as required as per KSEI specifications.

OD79129/2023-2024:Supplying, laying and clamping of 3 x 300 Sq.mm XLPE insulated AL HT armoured power cable, conductors of best conductivity aluminium 11KV grade of following sizes in existing cable tray / existing trench (excluding sand cushioning and protective covering) / clipping directly on wall / ceiling

OD79130/2023-2024:Supplying all material (Termination kit) and providing indoor / outdoor end termination for existing XLPE insulated AL conductor HT power cable 3 x 300 Sq mm to the transformer HT terminal as per IS 1255. Including properly cleaning, aligning and providing mechnical support to the cable, inspection for any defects etc.

OD79131/2023-2024:Supply and installation of following Current transformer with enclosure for neutral CT of the transformer ,5P10 Class

OD79136/2023-2024:Supply, erection, testing and commissioning of cubicle type, dust and vermin proof, floor mounted, front operated extensible type MV panel board made out of 16SWG thick CRCA sheet fully compartmentalised, duly rust inhibited,degreasing,zinc phosphating and painted with epoxy paints of approved colour and quality, complete with hinged and earthed front doors , name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made of 3mm thick sheet steel, all connections and inter-connections including mounting the following switch gears. (the panel shall be fabricated by a CPRI approved vendor) Incomer: 320A 4P MCCB Isolator ,Busbar : 320A TPN AL, CT:-320/5A CL-1,15 VA -3Nos ,MFDM with RS 485 - 1 Nos RYB phase indicating lamps (LED ) with control fuses, push buttons and switches -1 set. Outgoings: 250A 36kA 3P current limiting type MCCB with encapsulated double break mechanism- 2 Nos. B)MCCB mechanical Interlock system 1 set C) Heavy Duty Soft Starter Drive suitable for 100HP motor with capacitor and CDC with 3 built-in RJ45 communication ports , 1 Ethernet port, 2 serial ports working at a rated supply voltage from 380V to 480V AC. – 2 NOS D) 150A AC 3 power contactor 2 Nos

OD79135/2023-2024:Supply, erection, testing and commissioning of cubicle type,dust and vermin proof, floor mounted, front operated extensible type MV panel board made out of 16SWG thick CRCA sheet fully compartmentalised, duly rust inhibited,degreasing,zinc phosphating and painted with epoxy paints of approved colour and quality, complete with hinged and earthed front doors , name plate,danger notice board, heavy duty rubber gaskets, removable gland plates made of 3mm thick sheet steel, all connections and inter-connections including mounting the following switch gears. (the panel shall be fabricated by a CPRI approved vendor) Incomer: 160A 4P MCCB ISO Busbar : 160A TPN AL CT:-160/5A CL-1,15 VA -3Nos MFDM with RS 485 - 1 Nos RYB phase indicating lamps (LED ) with control fuses,push buttons and switches -1 set. Outgoings: (a)125A 25kA 3P current limiting type MCCB with encapsulated double break mechanism- 2 Nos. (b)MCCB mechanical Interlock system 1 set c) Heavy duty Soft Starter with voltage protection relay for 40 HP motor with capacitor & CDC -2 nos

OD79145/2023-2024:Supplying, laying and clamping of XLPE insulated and PVC sheathed armoured power cable, conductors of best conductivity aluminium 1.1KV grade strictly conforming IS: 1554 (Part I) of following sizes in existing cable tray / trench / clipping directly on wall / ceiling-3.5x300sqmm

OD79146/2023-2024:Supplying, laying and clamping of 3.5x240sqmm XLPE insulated and PVC sheathed armoured power cable, conductors of best conductivity aluminium 1.1KV grade strictly conforming IS: 1554 (Part I) of following sizes in existing cable tray / trench / clipping directly on wall / ceiling

OD79148/2023-2024:Supplying, laying and clamping of XLPE insulated and PVC sheathed armoured power cable, conductors of best conductivity aluminium 1.1KV grade strictly conforming IS: 1554 (Part I) of following sizes in existing cable tray / trench / clipping directly on wall / ceiling- 3x120 sqmm

OD79151/2023-2024:Supplying, laying and clamping of XLPE insulated and PVC sheathed armoured power cable, conductors of best conductivity aluminium 1.1KV grade strictly conforming IS: 1554 (Part I) of following sizes in existing cable tray / trench / clipping directly on wall / ceiling-3.5x70 sqmm

OD79152/2023-2024:Supplying, laying and clamping of XLPE insulated and PVC sheathed armoured power cable, conductors of best conductivity aluminium 1.1KV grade strictly conforming IS: 1554 (Part I) of following sizes in existing cable tray / trench / clipping directly on wall / ceiling-3.5x35 sqmm

OD79154/2023-2024:Supplying, laying and clamping of 4x16 sq.mm XLPE insulated and PVC sheathed armoured power cable, conductors of best conductivity aluminium 1.1KV grade strictly conforming IS: 1554 (Part I) of following sizes in existing cable tray / trench / clipping directly on wall / ceiling

OD79165/2023-2024:Supplying, laying and clamping of XLPE insulated and PVC sheathed armoured power cable, conductors of best conductivity aluminium 1.1KV grade strictly conforming IS:1554 (Part I) of following sizes in existing cable tray /trench / clipping directly on wall / ceiling. 3x25 sqmm cu ar cable

OD79156/2023-2024:Supplying, laying and clamping of XLPE insulated and PVC sheathed armoured power cable, conductors of best conductivity aluminium 1.1KV grade strictly conforming IS: 1554 (Part I) of following sizes in existing cable tray / trench / clipping directly on wall / ceiling-4x1.5 sq.mm copper cable

OD79157/2023-2024:Supplying, laying and clamping of XLPE insulated and PVC sheathed armoured power cable, conductors of best conductivity aluminium 1.1KV grade strictly conforming IS: 1554 (Part I) of following sizes in existing cable tray / trench / clipping directly on wall / ceiling-2x1.5 sq.mm copper cable

OD79158/2023-2024:Supplying, laying and clamping of XLPE insulated and PVC sheathed armoured power cable, conductors of best conductivity aluminium 1.1KV grade strictly conforming IS: 1554 (Part I) of following sizes in existing cable tray / trench / clipping directly on wall / ceiling-1c x 95 sqmm copper flexible cable

OD79166/2023-2024:Supplying and fixing of compression gland for armoured aluminium/copper conductor cable 1.1kv grade and making end termination suitable for 2/3/3.5/4 core cables of the following sizes as required 3.5x300sqmm

OD79167/2023-2024:Supplying and fixing of compression gland for armoured aluminium/copper conductor cable 1.1kv grade and making end termination suitable for 2/3/3.5/4 core cables of the following sizes as required 3.5x240sqmm

OD79168/2023-2024:Supplying and fixing of compression gland for armoured aluminium/copper conductor cable 1.1kv grade and making end termination suitable for 2/3/3.5/4 core cables of the following sizes as required 3x120 sqmm

OD79169/2023-2024:Supplying and fixing of compression gland for armoured aluminium/copper conductor cable 1.1kv grade and making end termination suitable for 2/3/3.5/4 core cables of the following sizes as required 3.5x70 sqmm

OD79170/2023-2024:Supplying and fixing of compression gland for armoured aluminium/copper conductor cable 1.1kv grade and making end termination suitable for 2/3/3.5/4 core cables of the following sizes as required 3.5x35 sqmm

OD79180/2023-2024:Supplying and fixing of compression gland for armoured aluminium/copper conductor cable 1.1kv grade and making end termination suitable for 2/3/3.5/4 core cables of the following sizes as required 4x16 sq.mm

OD79198/2023-2024:Supplying and fixing of compression gland for armoured aluminium/copper conductor cable 1.1kv grade and making end termination suitable for 2/3/3.5/4 core cables of the following sizes as required.

OD79184/2023-2024:Supplying and fixing of compression gland for armoured aluminium/copper conductor cable 1.1kv grade and making end termination suitable for 2/3/3.5/4 core cables of the following sizes as required 4x1.5 sq.mm copper cable

OD79195/2023-2024:Supplying and fixing of compression gland for armoured aluminium/copper conductor cable 1.1kv grade and making end termination suitable for 2/3/3.5/4 core cables of the following sizes as required 2x1.5 sq.mm copper cable

OD79193/2023-2024:Supplying and fixing of compression gland for armoured aluminium/copper conductor cable 1.1kv grade and making end termination suitable for 2/3/3.5/4 core cables of the following sizes as required 1c x 70 sqmm copper flexible cable

OD79201/2023-2024:Supply and providing ISI plate earthing as per IS: 3043 with 1200x1200x12mm CI earth plate with Cu strip extending to the other end of the earth plate and bolt to the plate with minimum 3 nos. of SS bolts, filling earth enhancing mineral compount of approved type around earth plate upto a distance of 15cm. with cover

OD79203/2023-2024:Supply and laying Copper strip /GI strip of the following sizes laid 0.6m below ground level excluding excavating trench of suitable size/tray and refilling etc as required 25x6mm Copper strip

OD79202/2023-2024:Supply and laying Copper strip /GI strip of the following sizes laid 0.6m below ground level excluding excavating trench of suitable size/tray and refilling etc as required 25x3mm Copper strip

OD79207/2023-2024:Fixing of 32x6 mm Cu Earth clamp (Main Earth Terminal / Earth bus) with all provision for making protective earthing system and equipotential bonding

OD79206/2023-2024:Supply and drawing bare copper conductors of the following sizes along with wiring/ cables and giving connections as required

OD79218/2023-2024:Supply and installation of 3 phase double cover MCB vertical DB IP42/43 including copper busbar, neutral link and DIN bar suitable for fixing outgoing MCB, flush mount on wall, including cutting holes on the wall making good the damage etc. as required

OD79217/2023-2024:Supply and installation of double cover enclosure of MCB DB IP42/43 for 1phase inclusive of copper/brass bus bar, neutral link and DIN bar suitable for incorporating MCB, isolator etc, flush mount on the wall including cutting holes on wall,making good the damages etc. as required

OD79216/2023-2024:Supply and installation of following accessories / circuit breaker in exisitng VDB / DB and making all connections, dressing up as per Electrical schematic and DB schedule, using suitable terminal sockets, marking ferrules etc complete. 100A TP MCCB

OD79215/2023-2024:Supply and installation of following accessories / circuit breaker in exisitng VDB / DB and making all connections, dressing up as per Electrical schematic and DB schedule, using suitable terminal sockets, marking ferrules etc complete. 63/40A FP Isolator

OD79214/2023-2024:Supply and installation of following accessories / circuit breaker in exisitng VDB / DB and making all connections, dressing up as per Electrical schematic and DB schedule, using suitable terminal sockets, marking ferrules etc complete. 40A TP MCB

OD79213/2023-2024:Supply and installation of following accessories / circuit breaker in exisitng VDB / DB and making all connections, dressing up as per Electrical schematic and DB schedule, using suitable terminal sockets, marking ferrules etc complete. 32A TP MCB

OD79212/2023-2024:Supply and installation of following accessories / circuit breaker in exisitng VDB / DB and making all connections, dressing up as per Electrical schematic and DB schedule, using suitable terminal sockets, marking ferrules etc complete. 16A TP MCB

OD79211/2023-2024:Supply and installation of following accessories / circuit breaker in exisitng VDB / DB and making all connections, dressing up as per Electrical schematic and DB schedule, using suitable terminal sockets, marking ferrules etc complete. 6A-32A SP MCB

OD79210/2023-2024:Supply and installation of following accessories / circuit breaker in exisitng VDB / DB and making all connections, dressing up as per Electrical schematic and DB schedule, using suitable terminal sockets, marking ferrules etc complete. 63A100mA FP RCCB

OD79209/2023-2024:Supply and installation of following accessories / circuit breaker in exisitng VDB / DB and making all connections, dressing up as per Electrical schematic and DB schedule, using suitable terminal sockets, marking ferrules etc complete. 40A 30mA DP RCCB

OD79208/2023-2024:Supply and installation of following accessories / circuit breaker in exisitng VDB / DB and making all connections, dressing up as per Electrical schematic and DB schedule, using suitable terminal sockets, marking ferrules etc complete. 40A 2P Isolator

OD79219/2023-2024:Supply Fixing of medium grade rigid PVC conduit, open or concealed as required in circuit wiring etc

OD79139/2023-2024:Supply all material and wiring for light / fan point (Primary or first point of group control lights) using 3 runs 1.5 sqmm FR PVC insulated copper wire, modular switches, front plate, MS Box, wiring connector, flexible connection using 2/3 core flexible round cables etc.,. 2 way controlled points shall counted as 2 points.

OD79140/2023-2024:Wiring for Secondary light points (looping) using 2 runs 1.5 sqmm FR PVC insulated copper wire or 1.5sqmm 3 core flexible weather proof cable.

OD79141/2023-2024:Wiring for 6A plug points in combined position using 3 runs1.5 sqmm FR PVC insulated copper wire including supply and fixing of 6A / 3 pin modular plug socket, switches and giving connections. (circuit from same switch board)

OD79142/2023-2024:Supply all materials and wiring for 6A/16A plug points in independent position using 2 runs 2.5 sqmm + 1 run 1.5 sqmm FR PVC insulated including supply and fixing of MS box, 6A / 16A 3 pin modular socket, switch, front plate, conduiting and giving connections.(with out circuit wiring)

OD79144/2023-2024:Supply and drawing PVC FRLS insulated copper wire of following size through existing conduit and giving necessary connections etc as required in the following runs.

OD79143/2023-2024:Supply and drawing PVC FRLS insulated copper wire of following size through existing conduit and giving necessary connections etc as required in the following runs. 2Runs 4mm² Cu wire + 1Run 2.5mm² Cu wire

OD79150/2023-2024:Supply Installation, testing and commissioning of the following items including cutting holes for recessed fittings, fixing anchor bolt for fan clamps etc. complete.(supply of lights in client scope)-LED flood lights. (50 watts)

OD79149/2023-2024:Supply Installation, testing and commissioning of the following items including cutting holes for recessed fittings, fixing anchor bolt for fan clamps etc. complete.(supply of lights in client scope)-LED Tube light

OD79164/2023-2024:Supply of 11kV grade rubber gloves

OD79163/2023-2024:Providing MV voltage danger notice board 200mmx150mm

OD79162/2023-2024:Providing high voltage danger notice board 300mmx200mm

OD79161/2023-2024:Supply & fixing Laminated drawings of electrical lay out and schematic drawing, shock treatment chart etc on good frame work.

OD79160/2023-2024:Supply & installation of following electrical grade rubber mat conforming to IS standards

OD79159/2023-2024:Supply & installation of following electrical grade rubber mat conforming to IS standards

OD79172/2023-2024:Supply and installation of emergency push button

OD79173/2023-2024:Charges for testing CT PT unit and TOD meter at TMR and recollecting the same after testing (professional charges only

OD79178/2023-2024:Charges for testing EFR,neutral CT,other relays at meter testing and standards laboratory and obtaining certificate excluding statutory and sundry charges

OD79181/2023-2024:Charges for supply and installation of HT TOD meter-Class 0.2S, 11KV/110V,-/5A,3-Phase 4 wire conforming to KSEB guidelines

OD79183/2023-2024:Supply and installation of 1 HP vaccum pump set with necessary starter

OD79182/2023-2024:Supply of cable termination box motors of suitable size for each motors

OD79185/2023-2024: Supply and erection of Perforated cable tray with suitable mounting achour fastners & mounting accessories as required confirming with all neccessary accessories

OD79186/2023-2024:Supply all materials and Fabrication and erection of supports fabricated out of MS angles C Channel and M S flats of adequate size for erection of panel boards, other necessary equipments etc The supports shall be painted with 2 coats of zinc chromate primer and 2 coats of enamel paint.

OD79191/2023-2024:Preparation of all files ,submission of completion certificate, arranging inspection, getting energisation sanction from Electrical Inspectorate (Excluding statutory and sundry charges)

OD79192/2023-2024:Preparation of all drawings submitting and getting scheme approval from Electrical Inspectorate, submitting of completion certificate, arranging inspection, getting energisation sanction from electrical Inspectorate and obtaining permanent power allocation & power connection from KSEBL. (Excluding statutory and sundry charges)

OD79190/2023-2024:Preparation of all documents and obtaining permanent power allocation & power connection from KSEBL.(Excluding statutory and sundry charges)

Appendix-B -Supply and Erection of CF Pump set at Clear water Pumphouse- 30 MLD WTP at Mavelikkara

OD60160/2023-2024:Supply and erection of CF pump set with the following specification 1.Pump Supply, erection, testing and commissioning of KWA pre- qualified reputed make Centrifugal pump sets with Bronze/SS impeller, SS shaft and CI pump casing with suitable type base plate with coupling, coupling guard foundation bolts & nuts etc. complete suitable for coupling the pump and motor above the base plate etc. complete including providing suitable concrete foundation including cost of cement sand and metal etc. complete The duty condition is as follows Discharge 73LPS Total head 27 meters Suction head 03 meters Length of suction pipe 03 meters Alternatively, the inlet & out let levels, type, size amp; length of pumping main etc. can be given. Modification may be done for Monoblock pump sets Flexible coupling shall be used for coupling of pumps and motors including Extended warranty of 2 years Rate as per Circular No. 9710/AE 15/2021/KWA Dated 08/02/2023 "

OD60166/2023-2024:Supply and erection of CF pump set with the following specification 1.Pump Supply, erection, testing and commissioning of KWA pre- qualified reputed make Centrifugal pump sets with Bronze/SS impeller, SS shaft and CI pump casing with suitable type base plate with coupling, coupling guard foundation bolts & nuts etc. complete suitable for coupling the pump and motor above the base plate etc. complete including providing suitable concrete foundation including cost of cement sand and metal etc. complete The duty condition is as follows Discharge 69 LPS Total head 60 meters Suction head 03 meters Length of suction pipe 03 meters Alternatively, the inlet & out let levels, type, size amp; length of pumping main etc. can be given. Modification may be done for Monoblock pump sets Flexible coupling shall be used for coupling of pumps and motors including Extended warranty of 2 years Rate as per Circular No. 9710/AE 15/2021/KWA Dated 08/02/2023 "

OD60167/2023-2024:Supply and erection of CF pump set with the following specification 1.Pump Supply, erection, testing and commissioning of KWA pre- qualified reputed make Centrifugal pump sets with Bronze/SS impeller, SS shaft and CI pump casing with suitable type base plate with coupling, coupling guard foundation bolts & nuts etc. complete suitable for coupling the pump and motor above the base plate etc. complete including providing suitable concrete foundation including cost of cement sand and metal etc. complete The duty condition is as follows Discharge 66 LPS Total head 70 meters Suction head 03 meters Length of suction pipe 03 meters Alternatively, the inlet & out let levels, type, size amp; length of pumping main etc. can be given. Modification may be done for Monoblock pump sets Flexible coupling shall be used for coupling of pumps and motors including Extended warranty of 2 years Rate as per Circular No. 9710/AE 15/2021/KWA Dated 08/02/2023 "

OD59709/2023-2024:Motor - Supply, erection, testing and commissioning of KWA pre qualified reputed make horizontal solid shaft foot mounted TEFC squirrel cage induction motor suitable for the above pump working 3 phase 50 Hz AC supply, working voltage 415 V The motor shall confirm to EEF1/IS 325 including providing suitable concrete foundation including cost of cement sand and metal etc. complete For 3300v motors digital motor protection relay shall be included in starter as per present CEA regulations. Flexible coupling shall be used for coupling of pumps and motors including Extended warranty of 2 years. Rate as per Circular No. 9710/AE 15/2021/KWA Dated 08/02/2023

OD59711/2023-2024:Supplying and fixing 900mm electro - magnetic flow meter including specials conforming to protection level of IP - 68 for Flow sensor and IP - 67 for transmitter and having an accuracy level of 0.5% with LED/LCD Display unit. The flow meter should have the housing (flow sensor) to be made of SS 304/ Carbon Steel with anti corrosive protection and inside liner to be made up of Hard Rubber / neoprene all confirming to drinking water standards. The flow meter should be coupled with HARt for data acquisition and transfer through GSM. The manufacturers should have the calibration standards as per ISO 17025 and the product shall have sufficient warranty provisions.Test certificate from FCRI palakkad.

OD59713/2023-2024:Supply, laying, testing and commissioning 2 run of 3core 400 Sq.mm PVC/XLPE insulated, sheathed armoured Aluminium conductor cable (1100/11000 Volts grade) clamped on wall/ceiling with clamps and saddle clips partly laid in cable tray/partly laid in trench.<br><br>

OD59714/2023-2024:Supplying and fixing 32Amps,TPN,6 way distribution tap off box with ISI markes HRC fuses

OD59715/2023-2024:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.(2X 4 sq. mm 1 X 4 sq. mm earth wire) (Item No 1.7.3 DSR E&M ) .

OD59716/2023-2024:Wiring for llight point/fan point/exhoust fan point /call bell point with 1.5 sqmm FRLVS pvc insulatedcopper conductor single core cable in surface recessed steel conduit with modular switch, modular plate, suitable GI box and earthing the point with 1.5sqmm FRLS pvc insulated copper conductor single core cable etc. as required<br>

OD59717/2023-2024:Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3pin/ 5/6 amps modular socket outlet and 5/6amps modular switch in the existing modular box by increasing the size of the box plate etc as required.

OD59718/2023-2024:Supply, Installation, testing and commissioning of 1200mm ceiling fan of reputed brand ( Crompton greeves,bajaj,Usha,Havels, Khaitan) with best quality stepped electronic regulator including charges for wiring the down rods of standard length(upto 30cm) with 1.5 Sq.mm FR PVC insulated copper conductor single core cable including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

OD59719/2023-2024:Installation, testing and commissioning of 12Watts LED Bulb of reputed brand ( Bajaj, GE, Havels, Osram, Philips, Surya, Syska) directly on ceiling or wall including connection with 1.5 Sq.mm FR PVC insulated copper conductor single core cable etc. as required.

Appendix-C- Electromechanical work-Raw water Pump house at Mandapathinkadavu

OD80221/2023-2024:Supply Installation, testing and commissioning of 400KVA Unitised substation consisting of the following,11KV,high voltage panel board comprising of KSEB metering facilities with CT and PT,1No. Load break switch of 350 MVA capacity, Bus bar sections 350Amps capacity. With copper winding, having a continuous rating for,11KV/433V 3 phase 50Hz.Vector group Dyn-11.USS should have cable end box on HV side suitable for 3Cx150Sq.mm XLPE cable and suitable end box for connecting 32Rx3.5Cx185Sq.mm Aluminium XLPE cable on LV side, with all fittings and accessories, complete as required as per KSEI specifications.

OD59721/2023-2024:Supply errection testing and commissioning of 11 Kv data acquisition copatible extensible type Ring main unit incorporated with one No. VCB and two load break switch Totally enclosed (11 kv,630A,,350MVA ,36KA)

OD59723/2023-2024:Supply and laying 11 kv 3 core 300 sqm stranded compact circular aluminium conductor,<br>conductors screened with extruded semi conducting compound XLPE<br>insulated, insulation screened with extruded semi conducting compound<br>in combination with copper tape (0.3KA for I sec.) cores laid up. inner<br>sheath of PVC tape, galvanized steel flat strip armoured, and overall<br>PVC sheathed cable conforming to IS: 7098 part II 1985 with latest<br>amendment

OD59724/2023-2024:Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : <br>3x300 sq.mm out door

OD59725/2023-2024:Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:<br>3x300 sq. mm indoor

OD59726/2023-2024:Charges for transporting the 11 kv CTunits and testing to the laboratories of KSEB and procuring approval for them.<br><br>

OD59727/2023-2024:Supply and fixing of HT TOD meter including testing.

OD59728/2023-2024:Supply all materials and fixing of emergency push button with enclosure

OD59729/2023-2024:Supply and fixing of neutral CT 200/5A, CL.5P10, 15VA on suitable enclosure.

OD59731/2023-2024:Supply and laying 1 Run of 240 sqmm 3.5 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

OD59732/2023-2024:Supply all materials and termination of 3.5X240 sqmm XLPE cable

OD59733/2023-2024:Earthing with G.I. earth plate 1200 mm X 1200 mm X 12 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

OD59734/2023-2024:Supply and laying following 32x6mm GI strip

OD59735/2023-2024:Supplying and laying 25 mm X 6 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

OD59736/2023-2024:Supply and laying following Swg 10 copper conductor

OD59737/2023-2024:Supply and laying of the following aluminium armoured LT cable using all suitable accessories through existing cable trench or cable trays. 3 x 300 Sq mm Al ar. cable - 200Meter, 4 x 6 Sqmm Al ar cable - 10 meter

OD59738/2023-2024:Supply &termination of the following aluminium armoured LT cables using cable gland, aluminium crimping socket etc . 3x300 Sq mm Al ar.cable - 6 Nos, 4 x 6 Sqmm Al ar cable - 1meter

OD59739/2023-2024:Supply and installation of the following for fire protection.<br> H.T. Rubber mat 1/2'' thick- 3Nos L.T. Rubber mat 1/4'' thick - 2 Nos H.T.gloves - 2 pair Fire bucket with single stand -3 Nos HT Danger board - 1Nos LT Danger board - 6 Nos Fire extinguisher(5 KG DCP type) - 2 Nos Shock treatment chart - 1Nos First aid box - 2Nos

OD59740/2023-2024:Supply all materials and Fabrication and erection of cable trays /cable supports fabricated out of MS angles and M S flats of adequate size with sufficient width and spacing between sucessive cross members and supports at adequate spacing . The cable trays and supports shall be painted with 2 coats of zinc chromate primer and 2 coats of enamel paint.

OD59741/2023-2024:Arrangements of soil resistivity certificate

OD59742/2023-2024:Supplying and laying 2 core 2.5mm copper cable for emergency push botton arrangements

OD59743/2023-2024:Termination unit for emergency push button arrangments

OD59744/2023-2024:Providing light wiring arrangements (Single phase) in the sub station room including supplying and fitting meter board with single phase 15A main switch, fuses etc. as per KSEB rules.

OD59745/2023-2024:Preparation of schematic diagram, earthing arrangements , physical layout site plan and submitting to the Electrical inspectorate for getting necessary approval and obtaining energization sanction from the Electrical inspectorate. Preparation of necessary drawings, submitting completion report, getting power supply from KSEB

OD59746/2023-2024:Supply, Fabrication, Installation, Testing and Commissioning of Cubicle type, dust and vermin proof, floor mounted, front operated APFC Panel (350kVAR) made out of 16SWG thick CRCA sheet fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel, switch board having a set of suitably rated TPN Aluminium Busbars with the specified current and fault level, insulated with heat shrinkable, colour coded PVC sleeves and supported using DMC/SMC piller or finger type Busbar supports consisting of the following 800A MCCB 1No Multifunction Meter 1No CT 600/5A 15VA CL-1 3Nos APFC Relay (12Way) 1No 125A 3P MCCB 2No 63A TP MCB 5Nos 40A TP MCB 2Nos 32A TP MCB 2Nos 50kVAR Capacitor Duty Contactor 4Nos 25kVAR Capacitor Duty Contactor 2Nos 20kVAR Capacitor Duty Contactor 2Nos 15kVAR Capacitor Duty Contactor 3No 10kVAR Capacitor Duty Contactor 1No 5kVAR Capacitor Duty Contactor 1No 50kVAR Capacitor (APP) 4No 25kVAR Capacitor (APP) 2Nos 20kVAR Capacitor (APP) 2Nos 15kVAR Capacitor (APP) 3Nos 10kVAR Capacitor (APP) 1No 5kVAR Capacitor (APP) 1No

100.31.2.7:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 300mm diameter, Class II.

100.31.2.8:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 350mm diameter, Class II.

100.98.434:Supply of CI Non Return Valve, Conforming to IS 5312 Part I - 1984, PN 1.0, Size 300mm.

OD60270/2023-2024:Supply of CI Non Return Valve, Conforming to IS 5312 Part I - 1984, PN 1.0, Size 350mm

Appendix-D-Supplying and Erection of VT Pump set at Raw water Pumphouse at Mandapathinkadavu

OD75675/2023-2024:M.S ERW column pipe of suitable diameter and SS 316 shaft in Intake structure . Supply, erection, testing and commissioning of KWA pre- qualified reputed make VT Pump sets with Bronze/SS impeller, SS shaft and CI pump casing with suitable type base plate with coupling, coupling guard foundation bolts & amp; nuts etc. complete suitable for coupling the pump and motor above the base plate etc. complete including providing suitable concrete foundation including cost of cement sand and metal etc. complete. The duty conditions of 2 pump set working together area: - Discharge of each pump - 368.75 LPS, Total head- 28.00 m, suitable delivery size so as to suit the pumping main. Erecting the pump set in the pump house by providing necessary RCC foundation fitting the motor on the pump stool, erecting the starters, panel board, capacitors etc., and giving electric connection to all equipment as per CEA regulation and providing earthing for motors, etc with suitable cable and connecting the same to the earth pit provided as per IS 3043/87 and CEA regulations. Flexible coupling shall be used for coupling of pumps and motors including Extended warranty of 2 years Rate as per Circular No. 9710/AE 15/2021/KWA Dated 08/02/2023 "

OD79858/2023-2024:Supply, erection, testing and commissioning of cubicle type,dust and vermin proof, floor mounted, front operated extensible type MV panel board made out of 16SWG thick CRCA sheet fully compartmentalised, duly rust inhibited,degreasing,zinc phosphating and painted with epoxy paints of approved colour and quality, complete with hinged and earthed front doors , name plate,danger notice board, heavy duty rubber gaskets, removable gland plates made of 3mm thick sheet steel, all connections and inter-connections including mounting the following switch gears. (the panel shall be fabricated by a CPRI approved vendor) WITH Incomer: 630A 4P MCCB ISO Busbar : 630A TPN AL CT:-630/5A CL-1,15 VA -3Nos MFDM with RS 485 - 1 Nos RYB phase indicating lamps (LED ) with control fuses,push buttons and switches -1 set. Outgoings: A)500A 36kA 3P current limiting type MCCB with encapsulated double break mechanism- 2 Nos. B) MCCB mechanical Interlock system 1 set C) Heavy duty Soft Starter suitable for 220HP motor with 3 built-in RJ45 communication ports , 1 Ethernet port, 2 serial ports, working at a rated supply voltage from 380V to 480V AC suitable for 220HP motor. - 2 NOS D)400A AC 3 power contactor 2 Nos

OD79902/2023-2024:Supplying and fixing 900mm electro - magnetic flow meter including specials conforming to protection level of IP - 68 for Flow sensor and IP - 67 for transmitter and having an accuracy level of 0.5% with LED/LCD Display unit. The flow meter should have the housing (flow sensor) to be made of SS 304/ Carbon Steel with anti corrosive protection and inside liner to be made up of Hard Rubber / neoprene all confirming to drinking water standards. The flow meter should be coupled with HARt for data acquisition and transfer through GSM. The manufacturers should have the calibration standards as per ISO 17025 and the product shall have sufficient warranty provisions.Test certificate from FCRI palakkad.

OD79928/2023-2024:Supply, laying, testing and commissioning 2 run of 3core 400 Sq.mm PVC/XLPE insulated, sheathed armoured Aluminium conductor cable (1100/11000 Volts grade) clamped on wall/ceiling with clamps and saddle clips partly laid in cable tray/partly laid in trench.<br><br>

OD79927/2023-2024:Supplying and fixing 32Amps,TPN,6 way distribution tap off box with ISI markes HRC fuses

OD79929/2023-2024:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.(2X 4 sq. mm 1 X 4 sq. mm earth wire) (Item No 1.7.3 DSR E&M ) .

OD79930/2023-2024:Wiring for llight point/fan point/exhoust fan point /call bell point with 1.5 sqmm FRLVS pvc insulatedcopper conductor single core cable in surface recessed steel conduit with modular switch, modular plate, suitable GI box and earthing the point with 1.5sqmm FRLS pvc insulated copper conductor single core cable etc. as required<br>

OD79926/2023-2024:Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3pin/ 5/6 amps modular socket outlet and 5/6amps modular switch in the existing modular box by increasing the size of the box plate etc as required.

OD79925/2023-2024:Supply, Installation, testing and commissioning of 1200mm ceiling fan of reputed brand ( Crompton greeves,bajaj,Usha,Havels, Khaitan) with best quality stepped electronic regulator including charges for wiring the down rods of standard length(upto 30cm) with 1.5 Sq.mm FR PVC insulated copper conductor single core cable including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

OD79924/2023-2024:Installation, testing and commissioning of 12Watts LED Bulb of reputed brand ( Bajaj, GE, Havels, Osram, Philips, Surya, Syska) directly on ceiling or wall including connection with 1.5 Sq.mm FR PVC insulated copper conductor single core cable etc. as required.

Bidder Name

Horizia Construction(india)pvt ltd

ASWATHY AGENCIES