Supply Erection Testing and Commissioning of Electrification Work and Roof Top Solar Power Plant at Newly Construct Urban Primary Health Centre Fatepura of Vadodara municipal Corporation.(Percentage Rate Basis). (Re-Invite)

Name of work : SETC OF Electrification work & Roof Top Solar Powe Plant at Newly

Construct Urban Health Centre(UHC) Fatepura of Vadodara Municipal

Corporation.(%Rate Basis) (All Item Rate is without GST)

Quan Rate (in Rs.) Uni Amount (Rs)

Sr no Item Description tity (Excluding t

SECTION-1 POINT WIRING

1 Point wiring for Two Way Controlled Light Point 4 598 pt ₹

with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(green) both are of .ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires

erected in below type of pipe with 6A Modular

type switches and following type of accessories

erected on PVC / Metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate modules erected on /

in wall / ceiling as per pipe erected. with

necessary batten/angle holder or ceiling rose or

H.D.Connector as directed. (f) with medium class

Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete CAT-III

2 Point wiring for Light / Bell with 2-1.5 sq.mm 140 481 Pt ₹

& earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length , in

below type of pipe erected with 6A Modular

type switch / bell push & accessories and earth

continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base

frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling

as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as

directed.(f) with medium class Rigid PVC pipe

and accessories erected concealed in

wall/ceiling complete CATT-III

3 Point wiring for FAN with 2-1.5 sq.mm & earth 50 668 pt ₹

wire of 1.5 sq.mm (Green) both are of .ISI

marked 1.1 KV Grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in

below type of pipe erected with 6A Modular

type switch and hum free EME step type

electronic fan regulator mounted and

accessories with earth continuity of following

type erected on PVC / Metallic/Wooden box,

single mounting base frame covered with

textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected.

with necessary ceiling rose / H.D.Connector as

directed.(f) with medium class Rigid PVC pipe

and accessories erected concealed in

wall/ceiling complete catt-iii

4 Point wiring for Individual Plug with & earth 20 738 pt ₹

wire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type

of pipe erected complete with Modular type

switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate

front plate modules erected on / in wall / ceiling

as per pipe erected with following type of

accessories. [II] For 16A Plug and 16 amp switch

with 2-2.5 sq.mm Cu. Wire from mcb db board.(f)

with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

complete Cat. III

Point wiring for Individual Plug with & earth 5 863 Pt ₹

wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in

below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on

PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in

wall / ceiling as per pipe erected with

following type of accessories.[III] For 16A Plug

and 16 amp switch with 2-4 sq.mm Cu. Wire

with 2.5 sq.mm ( green) earthing wire from mcb

d b board.(f) with medium class Rigid PVC

pipe and accessories erected concealed in

wall/ceiling complete Cat. III

Point wiring for Individual Plug with & earth 20 505 Pt ₹

wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in

below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on

PVC / Metallic/Wooden box covered with

6 appropriate front plate modules erected on / in

wall / ceiling as per pipe erected with

following type of accessories. [I] For 6A Plug

and 6 a switch with 2-1.5 sq.mm Cu. Wire

from nearby switchboard/mcb db board (f) with

medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat.

7 Point wiring for on board Looped Plug with 6A 100 255 pt ₹

Modular type switch & 5 pin socket erected on

PVC / Metallic/Wooden box, single mounting

base frame covered with textured /

metallic/white front plate modules erected on

/ in wall / ceiling with following type accessories

8 Providing following type of Modular Type 25 25 eac ₹

Accessories mounted with PVC / h

metallic/Wooden box, single mounting base

frame covered with textured / metallic/white

front plate , modules erected with necessary

connections as per site situation directed by

Engineer In charge.(7) Blank Plate Single cat.III

9 Providing following type of Modular Type 40 179 eac ₹

Accessories mounted with PVC / h

metallic/Wooden box, single mounting base

frame covered with textured / metallic/white

front plate , modules erected with necessary

connections as per site situation directed by

Engineer In charge. (9) 16 Amp. SP one way

10 Providing following type of Modular Type 40 198 eac ₹

Accessories mounted with PVC / h

metallic/Wooden box, single mounting base

frame covered with textured / metallic/white

front plate , modules erected with necessary

connections as per site situation directed by

Engineer In charge. (10) 6/16Amp. Universal

11 Providing and erecting ISI mark Medium class 300 33 mtr ₹

RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with

necessary PVC fittings & Junction boxes fixed

with adhesive solution & Clamps with following

dia of pipes, in approved manner as directed (b)

12 Providing and erecting ISI mark Medium class 50 67 mtr ₹

RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with

necessary PVC fittings & Junction boxes fixed

with adhesive solution & Clamps with following

dia of pipes, in approved manner as directed (b)

13 Providing & erecting PVC Corrugated Flexible 20 17 mtr ₹

Conduit with required nos. of coupling, PVC .

bushes, Check-nuts etc. complete of following

sizes. (1) 20 mm

14 Providing and erecting Mains with 1.1 KV grade 350 62 mtr ₹

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling,

with 1.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) With medium

class Rigid PVC pipe and accessories(a) 2 wire

15 Providing and erecting Mains with 1.1 KV grade 400 82 mtr ₹

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling,

with 1.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) With medium

class Rigid PVC pipe and accessories (b) 2 wire

16 providing and erecting Mains with 1.1 KV grade 100 111 mtr ₹

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of

following size.(A) with medium class Rigid PVC

pipe and accessories(a) 2 wire 4 sq. mm

17 providing and erecting Mains with 1.1 KV grade 50 179 mtr ₹

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of

following size (A) with medium class Rigid PVC

pipe and accessories (g) 4 wire 4 sq. mm

18 providing and erecting Mains with ISI marked, 25 17 Mtr ₹

1.5KV grade electrolyte multi stranded, annealed .

copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected

in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor

starters & control wiring) with required size of

copper lugs, nuts and bolts if required. (b) One

wire 1.50 sq. mm

19 providing and erecting Mains with ISI marked, 25 27 Mtr ₹

1.5KV grade electrolyte multi stranded, annealed .

copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected

in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor

starters & control wiring) with required size of

copper lugs, nuts and bolts if required. (c) One

wire 2.50 sq. mm

20 providing and erecting Mains with ISI marked, 25 37 Mtr ₹

1.5KV grade electrolyte multi stranded, annealed .

copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected

in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor

starters & control wiring) with required size of

copper lugs, nuts and bolts if required. (d) One

wire 4.00 sq. mm

21 providing and erecting Mains with ISI marked, 25 56 Mtr ₹

1.5KV grade electrolyte multi stranded, annealed .

copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected

in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor

starters & control wiring) with required size of

copper lugs, nuts and bolts if required. (e) One

wire 6.00 sq. mm

22 providing and erecting Mains with ISI marked, 50 91 Mtr ₹

1.5KV grade electrolyte multi stranded, annealed .

copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected

in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor

starters & control wiring) with required size of

copper lugs, nuts and bolts if required. (f) One

wire 10.00 sq. mm

23 providing and erecting Mains with ISI marked, 50 141 Mtr ₹

1.5KV grade electrolyte multi stranded, annealed .

copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected

in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor

starters & control wiring) with required size of

copper lugs, nuts and bolts if required. (g) One

wire 16.00 sq. mm

Providing & erecting Switch board for 10 1122 Pt ₹

Computer or electric apparatus consisting of

following modular type accessories mounted

with PVC / Metallic concealed/open box with

single mounting base frame covered with

24 textured/metallic /white front plate,modules

erected with necessary connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type

Accessories Cat. III

25 Supplying & erecting Approved make call bell 8 147 eac ₹

indicator with buzzing sound and Red light h

indicating lamp with Red light button to attend

the call suitable for 240 v 50 c/s supply to be

SECTION -2 LED INDOOR FITTINGS

Supplying and erecting LED indoor fittings with 140 751 nos ₹

LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel

conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V.

& corrosion resistance with diffuser housed in

aluminium casted body with company

mark/name 160V to 270V,Power Factor more

than 0.95, THD < 15 %, CCT 3000 K to 6500K,

26 Luminaire efficacy> 85 lumens/watt , LED

driver efficiency > 85 %

( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed

Mount Downlight with provision for spring

loaded mounting clips complete.IP20 (iv) 22-24

watts, Surge-2 KV, Surge-2 KV Cat-lll

27 Supplying and erecting LED indoor fittings with 15 164 each ₹

LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel

conforming to IS: 513/CRCA/ aluminium die

cast powder coated and high U.V. & corrosion

resistance with diffuser with company

mark/name 160V to 270V, Power Factor more

than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.)

(A) Tube Light with integral driver (i) 5-10

Watts, Surge-2 KV, IP-20, conventional 1 to

28 Supplying and erecting LED indoor fittings with 5 370 each ₹

LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel

conforming to IS: 513/CRCA/ aluminium die

cast powder coated and high U.V. & corrosion

resistance with diffuser with company

mark/name 160V to 270V, Power Factor more

than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown)

(A) Tube Light with integral driver.(iv) 22-24

Watts, Surge - 2KV,IP-20, conventional 4 feet

29 Supplying and erecting LED street light / Flood 2 6501 each ₹

light fittings with High power White LEDs

wattage of 3 Watt and above assembled on

single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast

aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with

diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name

engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT

K to 5700K,Uniformity ratio >0.45, Luminaire

efficacy> 100 lumens/watt . LED driver

efficiency > 85 %.( fittings required LM-79 &

LM-80 certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges

shown.)(A) Street Light (IP-65), Surge

protection -4KV integral and ,Light must have

440VAC line supply with over-voltage

protection. (iv) above 90 to 120 watts.CATT-III

SECTION -3 SWICH GEAR &ACCESSARIOUS

30 providing and erecting Approved make Four pole 7 6112 each ₹

moulded case circuit breaker having breaking

capacity ICU of 25 KA. at 415 V, having normal

current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on A.C.

supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in

existing 16 G.M.S. housing. ICS=100% of ICU only

31 Providing and erecting Approved make Four pole 1 7976 each ₹

moulded case circuit breaker having breaking

capacity ICU of 35 KA. at 415 V. having normal

current rating 125A. with Fixed thermal &

magnetic release suitable to work on A.C. supply

c/s. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III

32 Supplying KITKAT pattern porcelain cut-out fuse 3 276 each ₹

with base of following current capacity erected on

existing block board. (v) 100 A. 500 V.

33 Supplying and erecting triple pole & neutral 440V / 3 3171 Rn.M ₹

500V panel mounting Copper Busbars with four tr

equal Nos. of electrolyte bus having current density

not more than 1.6 Amp. / sq.mm (Rated current /

cross section area) duly wrapped with colour

insulating tape for phase sequence of following

current carrying capacity, erected with necessary

bus bar supports /insulators, main cable socket to

each bar, erected in existing cubical panel with

necessary connections. (B) Suitable for 200 Amp.

34 providing and erecting Miniature circuit breaker 15 268 nos ₹

single pole 0.5A to 2A system and having breaking

capacity 10 KA to be erected in existing box.

confirming to IS 8828/1996 with ISI Mark Cat.III

35 Providing & erecting 415V MCB Four Pole Switch 4 632 nos ₹

for Lighting Load (B curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box

having following capacity (b)40 Amp. Cat.III

36 Supplying & erecting 20 Amp 10 KA ‘C Curve’ 4 522 nos ₹

single pole MCB with 20 Amp. Plug socket, company

fabricated powder coated sheet steel enclosure

erected as directed with connection. [A] Metal

Clad Socket with metal clad top

37 Providing & erecting 415 V MCB Four Pole for 8 730 Nos ₹

Motor & Inductive Load (C Curve) having 10KA

breaking capacity & confirms to IS :8828 in existing

box having following capacity (c)63 Amp. Cat.III

38 Providing and erecting Sheet Steel powder coated 2 3095 Nos ₹

MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of

MCBs.(The DBs should be used of same company of

MCB to be used) suitable for(B) three phase

incoming and single phase horizontal type outgoing

Per phase isolation type (PPI) (a) single door

39 Providing and erecting required size Aluminium 3 223 kg ₹

strip for earthing of H.T. , OCB / ACB / Transformer,

LT panel board, Motors etc. using copper clamp.

40 Providing and erecting metallic vitrified danger 8 69 each ₹

notice board as per language suggested by engineer

incharge for MEDIUM VOLTAGE installation to be

erected as per IS-2551.

41 providng and erecting Approved make energy 1 2670 each ₹

meter 3 phase 4 wire unbalanced load rating, 10A

to 60 Amp. based on ASIC(Application specific

Integral Circuits) digital technology with accuracy

Class - 1 , temper proof, free from effect of external

magnetic field with 3 phase indication, earth &

impulse indication, 6 digit electro mechanical

impulse counter, suitable work on 120 V to 300V

per phase 45-55 HZ, housed in robust enclosure

with erection as directed. Cat. III

42 providng and erecting Suitable set of CTS for 100A 1 2085 each ₹

43 providing and erecting Miniature circuit breaker 60 111 each ₹

single pole 6A to 25A suitable to operate on 240 V

A.C. system and having breaking capacity 10 KA to

be erected in existing box. confirming to IS

8828/1996 with ISI Mark catt-iii

44 Providing & erecting 240 V MCB double pole switch 10 297 each ₹

for motor & inductive load (C Curve) having

KA breaking capacity & confirms to IS : 8828 in

existing box having following capacity A) 6 to

45 Providing and erecting four pole Miniature isolator 2 590 each ₹

A.C. 22 duty confirms to IS 13947-3 in existing

box.(b) for 63 Amp. catt-iii

46 Sheets steel powder coated enclosure suitable for 3 175 each ₹

incorporating One/Two nos. MCB.

47 Providing and erecting Sheet Steel powder coated 4 696 each ₹

MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of

MCBs.(The DBs should be used of same company of

MCB to be used) suitable for.(A) single phase

incoming and horizontal single phase outgoing.

single door (IP-30).(iii)8 way

48 Providing and erecting Sheet Steel powder coated 2 1478 each ₹

MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of

MCBs.(The DBs should be used of same company of

MCB to be used) suitable for.(A) single phase

incoming and horizontal single phase outgoing.(b)

sheet steel double door (IP-43)(iv)12 way

49 providing and erecting Approved make RCCBs 7 2213 each ₹

conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase

V,50Hz. having characteristic of quick action &

tripping with all advance feature & do not

incorporate any electronic component. for

following Max. rating erected as directed.(ii)

40Amps. DP.catt-iii

50 Providing and erecting Approved make RCCBs 2 3010 each ₹

conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of

KA and suitable for operation on 3 phase and

neutral 415V,50Hz. having characteristic of quick

action & tripping with all advance feature & do not

incorporate any electronic component for following

Max. rating erected as directed.(iii) 63 Amps.

51 providing and erecting Approved make RCCBs 6 1950 each ₹

conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase

V,50Hz. having characteristic of quick action &

tripping with all advance feature & do not

incorporate any electronic component. for

following Max. rating erected as directed (i)

Amps.DP Cat. II

52 Providing and erecting Steel cover as per drawing 2 2535 Sq.Mt ₹

using 16 SWG M.S.sheet of following depth, to r

house the switch gear etc. complete with locking

arrangement and lock with duplicate keys per

cupboard and door handles erected with necessary

support and painting. [One coat red oxide and two

coat enamel paint] (B)Without angle iron frame (i)

For 25 cms. Depth

53 Providing and erecting Annealed bare Copper wire 5 787 kg ₹

54 Providing & erecting weather proof, dust & vermin 2 16162 Sq.Mt ₹

proof, floor mounted front operated outdoor type r

double door cubical panel board necessary IP-54

and above protection as per approval from

engineer incharge made from 14 SWG thick CRC

M.S. sheet for outer body & doors, 16 SWG thick

CRC M.S.sheet for internal partitions with necessary

accesories , supporting angles/ flats channel

including cutting, bending, drilling, welding,

riveting with internal partitions & cable alley as per

requirements & instruction of engineer-in-charge

with erection of supplied switch gears, BUSBARS,

suitable size of inter connecting PVC copper wire /

copper-aluminium strips, rubber grommets, rib,

bakelite control fuses/MCB for measuring

instruments, earth bus & earth bolts, foundation

flange - bolts-base Plates, sufficient nos. of hinged

doors, handles with locking arrangement and

rubber gasket,heavy duty end terminal

connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall

be painted with epoxy powder coating. (The rates

excludes the cost of switchgears, bus bars, inter

connecting mains & Copper Aluminium strips,

meters, Fuses etc. The dimension shall be measured

excluding base beams) The panel shall be supplied

with following approved manufacturers with

following size. (B) The standard companies switch

gear shall be used and only manufacturers at CPRI

approved factory (i) with 350mm depth

SECTION -4 CABLE &WIRE

Providing and erecting XLPE (IS:7098)(I)-88 ISI 500 139 Mtr ₹

armoured cable multistrand / Solid Aluminium

55 conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables (C) 4 core 10 Sq. mm

56 Providing and erecting XLPE (IS:7098)(I)-88 ISI 80 116 Mtr ₹

armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables (A) 4 core 4 Sq. mm

57 Providing and erecting XLPE(IS:7098)(I)-88 ISI 100 361 Mtr ₹

armoured cable multistrand / Solid Copper

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe at road

crossing or floor of following size of cables.(B)

58 Providing and erecting XLPE(IS:7098)(I)-88 ISI 40 978 Mtr ₹

armoured cable multistrand / Solid Copper

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe at road

crossing or floor of following size of cables. (B)

59 Making trench in Hard Murrum / Tar Road of 150 74 Mtr ₹

suitable width of 90 cm or required depth for laying

any size of cable or locating the fault all over the run

and back filling the same and making the surface as

60 Providing & laying approved make Double walled 500 62 Mtr ₹

corrugated pipes (DWC) of polyethylene(conforming

to IS 14930 II )with necessary connecting

accessories of same material at required depth in

existing trench for laying of cable. below ground /

road surface for enclosing cable (A)50 mm outer dia

61 Providing and, fixing heavy duty flange type brass 12 38 nos ₹

cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails,

insulating tape etc for following size of cables.(C) 2 to

4 core 10 Sq. mm

62 Providing and, fixing heavy duty flange type brass 15 33 nos ₹

cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails,

insulating tape etc for following size of cables.( (A)

to 4 core 2.5 / 4 Sq. mm

63 Solder less crimping type Aluminium lugs 30 13 nos ₹

conforming to IS suitable for cable of following size

evenly crimped with high pressure tool & connected

to switchgear terminals with brass/cadmium plated

nut bolts in an approved manner. (B) 10 Sq.mm

64 Solder less crimping type Aluminium lugs 64 6 nos ₹

conforming to IS suitable for cable of following size

evenly crimped with high pressure tool & connected

to switchgear terminals with brass/cadmium plated

nut bolts in an approved manner. (A) 1.5/ 2.5/4/6

65 Solder less crimping type Copper lugs conforming to 15 8 nos ₹

IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an

approved manner. (A) 1.5/2.5 to 6 Sq.mm

66 Solder less crimping type Copper lugs conforming to 30 10 nos ₹

IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an

approved manner. (B) 10 Sq.mm

SECTION -5 FAN &ACCESSARIES

67 Supply, Installation, Testing and Commissioning of 50 2603 each ₹

suitable sweep, BEE 5 Star rated, Ceiling fan with

Brush Less Direct Current (BLDC) permanent ferrite

magnet Motor, class of insulation: B, Rust free

nos.Aluminium blades, 2 nos. canopies, shackle kit

with earthing provision, copper winding, Power

factor not < 0.9, Service Value (CMM/W) minimum

6.85, Air delivery minimum 215 CMM, 350 RPM,230v

(tolerance as per IS : 374-2019), THD < 10%,

compitible with electronic regulator unit for Speed

Control and all remaining accessories including

safety pin, nut bolts, washers, temperature rise =

degree C (Max.), suitable for 140 to 285 Voltage and

rectifier circuit with surge, over current and overload

protection , 50 Hz, Single phase AC Supply, earthing

etc. Complete as required.[ Make shall be approved

by Engineer in Charge] (A) 1200 mm Sweep (48")

68 Supplying and erecting 19 / 20 mm. nominal bore 50 107 each ₹

Medium Class M.S. Pipe down rod erected duly

painted for fan complete with proper insulation

without leakage and earthing.

69 Supplying & erecting Fan Hook of 10 mm M.S. Round 50 43 each ₹

bar grouted in RCC slab with Making the site as

70 Supplying & erecting single phase approved make 6 2034 each ₹

industrial exhaust fan suitable for medium duty ring

mounted low noise operation suitable for medium

duty having following dia size and maximum speed in

RPM [A] 305 mm dia 900 RPM cat ii

71 Providing 2.5mm.thick laminated acrylic sheet to 50 18 each ₹

cover the fan hook or Fan box.

72 Supplying & erecting approved make low noise 5 1687 each ₹

decorative exhaust fan having square frame ABS

body with inbuilt lowers & square frame.200mm

with 1350RPM Cat.II

SECTION 6 Street Light

Supplying and erecting approved make Octagonal 15 8111 each ₹

pole made from HR sheet steel. The pole should be

made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction

box consist of terminal plate of min 6mm Hylam

sheet, standard profile 35mmX7.5mm Din-Rail for

MCB Mounting, stud type terminal and

73 arrangement for cable termination to be erected

With Suitable foundation (Included) as per details

given by manufacturer considering site

requirement.(D) 6 Mtr. Long 70 mm Top X

mm bottom dia, 3 mm thickness with

200mmX200mmX12mm base plate, 4-M20 Bolts and

600mm long with necessary G.I. J Bolts .Approx Pole

Providing and erecting street light pole bracket 15 608 each ₹

comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class G.I

sleeve tubing of approx. 45cms.length and suitable

for 76.5 mm / 80mm. / require size pole top having

sufficient fasteners for fixing the brackets and

74 having spread of 1 mtr. length with suitable rise as

per site condition & suitable welded stiffener reducer

and nipple with check nut complete painted with one

coat of Red oxide / PU base primer and two coats

of Aluminium / PU paint. paint with following nos

of arms..[A] Single Arm bracket 1 Mtr

75 Supplying & erecting approved make Digital time 1 3137 each ₹

switch having lithium cell 6 years operative and

operate battery backup 1 channel day clock with

memory programme, suitable to operate on 240V +

5%, 16A with, floating contacts Minimum switching

setup time 1 minimum & LCD display. Also

comprised permanent ON/OFF switching.

Programming switches & housed in fire proof

thermoplastic enclosure & transparent cover erected

as required with necessary connection erected as

76 Supplying & erecting power contactor ,AC3 duty for 1 849 each ₹

time switch complete erected as per direction Cat III

(C) 4 pole 440V 16 Amp.

Supplying and erecting LED street light / Flood light 15 4948 nos ₹

fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free

High pressure die cast aluminum housing with

smooth finish powder coated and heat sink

extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass

with company mark/name engraved or embossed

77 160 to 270 V,Power Factor more than 0.95, THD

< 10 %, CCT 3000 K to 5700K,Uniformity ratio

>0.45, Luminaire efficacy> 100 lumens/watt .

LED driver efficiency > 85 %.( fittings required

LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity

of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (A)

Street Light (IP-65), Surge protection -4KV

integral and Light must have 440VAC line supply

with over-voltage protection. (ii) above 48 to

SECTION 9 Motor Pump

78 Supplying and erecting Direct On-line Electronics 2 1588 each ₹

Starter with 2-5/4-10/8-14/10-16 Amp. Rating

relay (variable current setting) directly operated

in totally insulated elegant enclosure and 18 Amp.

Rating power relay with start - stop button for

single phase operation up to 3 HP as per complete

erected on P.W. Block with following features.

Low voltage cut off below 140 V

High voltage cut off above 280 V

Overload protection

Indicating LEDs for motor on lv, hv & overload

tripping. [Cat.II]

79 Supplying and erecting approved make suitable 9 43 each ₹

panel indicator LED type lamp, lens cover,

complete erected with necessary connections.

80 Providing & erecting open well type horizontal 2 9518 each ₹

mono block pump set with stainless steel body

having following specification (C) 1 H.P. single

phase open well motor pump set suitable for

LPM discharge @ 25 mtr. head, suitable for

mm dia. Delivery pipe with control panel. Cat. II

81 S.I.T.C. of single phase submersible pump set 1 15441 each ₹

suitable for 100 mm size or more dia bore well

having motor capacity and discharge as under

with necessary panel box. Lifting and Lowering

taken extra.(a) Motor rating 1 HP (12 stage)

pump having capacity of 50 LPM at 43 to 45 mtr

head suitable for 32 mm dia. delivery pipe

82 Providing and erecting ISI marked PVC insulated 150 103 Mtr ₹

PVC Sheathed Flat flexible Submersible copper

cable approved make of following Size. (B) 3 Core

83 Providing Water proof straight Joint in PVC 3 188 each ₹

insulated flat flexible copper cable by using

insulating material, water proofing material, &

making the joint complete. (A) Up to 10Sq. mm

84 Supplying of following size of STANDARD UPVC 100 178 RMT ₹

column pipe with coupler and wire lock [B]

SECTION 14- SOLAR PV SYSTEM

85 Supply, Installation, Testing & Commissioning of 7 43645 per ₹

following size of Grid Tied Solar Power Plant with kw

Solar Panels (ALMM approved): Frame Material :

Anodized Aluminum alloy Frame With Twin Wall

Profile, Front Cover : High Transmission Low-Iron

Tempered Glass (AR Coated), High efficency and

positive power tolerance Pmax: 0/+5, Module

Efficiency should be approx. 18%-21%, Normal

operating temperature 45'C, Junction Box with

Waterproof IP67 & MC4 Compatible and Enclosed

with Bypass diodes, 100% Electroluminescence

test to ensure error free Modules, Thep. temp. co-

efficient of the PV module shall equal or better

than -0.45%/degree C. Solar PV modules of

minimum fill factor 75% to be used. Unit

Production:- 4 to 5 Unit /kw /day (Actual)(1Year

Avg) With 10 year Product warranty and 25 year

Linear Power Warranty.,

Solar Inverter: MPPT Range: 80-1000 V, Max

efficiency: 97.5% - 98.9%, O/p Frequency:

50/60Hz, Operating Altitude (m) ≤4000, O/p

Power Factor: ~1, O/P THDi: <3%, Operating

Tempreture Range: -25~60°C, Anti-islanding

ntegrated, Input Reverse Polarity Protection

Integrated, Insulation Resistor Detection

Integrated, Residual Current Monitoring Unit

Integrated, Output Over Current Protection

Integrated, Output Short Circuit Protection

Integrated, Output Over Voltage Protection

Integrated, Protection Degree: IP65, User

Interface LCD & APP,Datalogger &

Communication: GPRS / Wi-Fi, Module Mounting

Structure: Seamless Box Pipe / 'C' Channel of

suitable size for rooftop solar installations with

good stability agaist wind & weight load., Hot

Dipped Galvanized steel coils. suitable

arrangement for base plate for foundation , solar

panel mounting, the structure should be suitable

for carry the load of solar panel,wiring, sprinkler

system etc. with necessary foundation work/wall

mount, j bolt, anchor fastner etc. the nut bolt used

for installtion of stucture should be (SS 304)

quality. and Balane of System with necessary

Swithgears (Suitabel size and protection of ACDB

& DCDB), inter connecting wiring, earthing

system, lightining arrester system, all liasoning

work with various gov. dipartment like state

nodal agency,DISCOM & CEIG is included in

agency scope (Excluding GEDA Application fees,

Solar connectivity Charges, Meter connectivity

Charges, Meter testing Charges.) (B) Grid Tied

Solar Power System: 7 - 10 kW (3 - phase)

Supplying & erecting earth pit of minimum bore 3 5703 each ₹

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm having

200- 250 Micron galvanising, connection terminal

dia of 12mm with constant ohmic value surrounded

by highly conductive compound with high charge

dissipation suitable for following type of

applications with chamber and heavy duty

cover.(approved make OEM has to submit test

certificate) & having back filling compound of (B)

Inner chemical (CCM Compound)- Resistivity:- 0.2 •

/ meter testing as per IEC 62561-2017, Voltage

drop:- < 1 volt at no load & dry form, Sulphar

content:- <2%(C) Back fill Compound :- Earthing

compound should be capable to retainmoisture for

long time Necessary test report must be

submitted.(c) For Electrical Installation covering

Transformer Neutrals, Lightning arrester Earthing,

A.C.Plant & Sensitive Computer System(like

Automation, SCADA) i.e independent (b)For

Electrical installation up to 11 KV in normal soil.

Length of Pipe : 2.00 mtrs Back filling Compound :1

no. Bag of 25 Kg

Providing and erecting Pipe type earthing having 3 365 each ₹

150 cms.long and 2.5 cms. dia. galvanised iron pipe

with coupling and buch buried in specially prepared

87 earth pit complete with necessary 8 SWG earth

wire. - to be used for each Street Light

Providing and erecting HOT deep Galvanised iron 10 77 kg ₹

strip wire 8 to 16 SWG.

Total Amount Rs.

Total Amount Rs.