ADDN ALTN IMPROVEMENT TO PERIMETER

Amount

Dismantling floor, hearth or wall tiling or stone slabs of any description including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified.

Demolition of brick work or stone masonry built in cement mortar including quoins, arches, pillars etc., and precast concrete articles and disposing off the rubbish materials outside MD land complete all as specified.

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified.

Demolition of Cement Concrete (un reinforced) of any description and in any position not otherwise specifically provided for complete all as specified.

Taking down plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern fixed in roof coverings or cladding complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.complete all as specified.

Excavating over areas, n exc 1.5 m deep and getting out in loose/soft soil complete all as specified.

Excavating over areas, exc 1.5 m deep and not exc 3 m deep and getting out in loose/soft soil complete all as specified.

Excavating in trenchs not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth and not exc 10 Sqm on plan in soft/loose soil and getting out complete all as specified.

Returning filling in including spreading, levelling, watering and well ramming in layer not exceeding 25 cm in soft and loose soil complete all as specified..

Removal of excavated material (soil) to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified.

M&L Cutting holes into or through cement concrete slabs, chajjas, column, brick wall etc. reinforced or otherwise exc 100 sqcm but n. exc 250 sqcm superficial area and making good the circular edges with CM 1:4 or cement concrete 1:2:4 type B-l as required complete all as specified.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, getting out in soft/loose soil complete all as specified.

M&L Sand filling for invert filler as shown on drawing including watering and consolidation complete all as specified.

M&L Coarse aggregate filling invert filler as shown on drawing complete all as specified.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified.

M&L PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in foundations, filling and massconcrete complete all as specified.

M&L PCC 1:2:4 Type B1 using 20mm graded stone aggregate as in benching, coping and the like including weathering slightly rounded or chamfered angles as directed including form work and finishing all exposed surfaces including necessary form etc. complete all as specified.

M&L RCC M25 (Design Mix) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified.

M&L RCC M25 (Design Mix) as in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified.

M&L Brick work with fly ash brick straight or curved on plans exc 6m means radius built in CM (1:6) complete all as specified.

M&L Dholpur stone 16 to 18mm thick cladding gang saw cut with machine cut edges, uniform colour of each stone size not exceeding 0.25 sqm over 10mm thick backing coat in CM 1:4 in straight courses about 50mm high and jointed in cement and stone dust mortar 1:3 and recessed pointed with an admixture of white cement and dholpur stone dust 1:1 matching with existing stone cladding and including, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment complete all as specified.

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified.

M&L Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pilasters, buttresses, etc.; vertical or to batter complete all as specified.

S&F Wire netting of galvanised steel wire 1.40mm dia, Size of mesh is 25mm fixed with tinned tacks of wire staples complete all as specified.

S&F MS Framed work such as grills, gratings,angle iron post etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 fixed on boundary wall complete all as specified.

Fixing only framed work such as grills, gratings, walk ways; railings,angle iron post fixed on boundary wall complete all as specified.

Mild TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm diabarbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete as in repairs all as specified (each line wire to be measured)

Labour only restraining/ re securing Galvanised. 2 strand, steel barbed wire and including making good staples etc complete all as specified

S&F Concertina coil with electro galvanised steel strip 0.5mm ± 0.02mm thick, width 19mm (before wrapping on central core wire) conforming to IS-1573, zinc coating-120gm / sqm and bituminous dipped, width of barbs 11.5mm, pitch of barbs 25.4mm ±0.20mmof 2 mm thick, and central core wire – made from high tensile spring steel core wire conforming to IS-4454 duly hot dipped galvanised( conforming to IS-2629) with dia 2.59mm ± 0.05mm, UTS 145-160Kg/sqmm, Zinc coating 250-300 gm/Sqm with 1050 mm dia coil fixed with AISI 304-15mm thick C&U clips ’C’ special type of coil and RBT wire ”U” clips special type for joining one coil to another coil and RBT wire to RBT wire joining complete as in repairs all as specified

Labour only restraining/ resecuring galvanised punched type concertina coil and including making good staples etc complete all as specified

M&L Welding n. exc 2.5cm in length, Thickness of Metal to be welded n. exc 6mm complete as in repairs all as specified

M&L Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws complete all as specified

Fixing only pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws complete all as specified

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:4) finished the surfaces even and smooth without using extra cement complete all as specified.

M&L Preparation of new plastered surfaces of wall and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior weather coat paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified.

M&L Preparation of old plastered surface of wall and applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior weather coat paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm complete all as specified.

M&L Preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of Red oxide primer including preparation of new steel/iron surface of any description over 10 cm in width or girth complete all as specified.

M&L Preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of Red oxide primer including preparation of new steel/iron surface of any description n.exc. 10 cm in width or girth complete all as specified.

M&L Preparation of old steel surface applying one coat of synthetic enamel paint over a coat of Red oxide primer including preparation of new steel/iron surface of any description over 10 cm in width or girth complete all as specified.

S&F PVC (SWR) 75mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

M&L 18 to 20mm thick Dura boardHD 100 (closed cell polymer) high preformed joint filler board confirming to IS 1838 (Part 3) as pproved by GE in writing for expansion joints fixed in vertical surface complete all as specified.

divyarsh entrprise

DMA PROJECTS

M/s Matadeen Ramchandra Agarwal