Supply and installation of Optimizer PLUS 2 Bay Drive Type units as storage space for Examination/Office documents and supplying of dining table and chairs for the second floor of Administrative Block for various programmes at the NUALS Campus

Amount

Supply and installation of Optimizer PLUS 2 Bay Drive Type, Static Drive 2 Bay– 1 Nos Last Drive 2 Bay – 1 Nos, Twin Drive 2 Bay – 4 Nos, Channel P1/P2 CHNL 800mm – 1 Nos, Channel P1/P2 CHNL 1600mm – 1 Nos, Channel P1/P2 CHNL 2400mm – 1 Nos, Overall Dimensions of SS2 - Single Static 2Bay Push Pull Type (U/C + Fittings) shall be 2400mm(W)x400mm(D)x2106mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS: 513.Each body shall have amain unit plus add on units (1,2,3,4,5). Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of minimum 40 microns. Shelf construction made of 0.7mm thick CRCA steel conforming to IS: 513 Gr. D or DD. Uniformly distributed load capacity of 60 Kg.Undercarriage shall have construction in welded frame CRCA sheet 2mm thick conforming to IS:513. Themovements of the system shall be Push pull configuration (TYPE-P1/TYPE-P2): Movement of unitsachieved by pushing or pulling 'C' type plastic handle (mounted on each double & single movable units) &rigidly fixed at suitable height on body side. Each movable body also has an understructure with 4 nos. of antifriction ball bearings for rolling on channels. The twin moving body, i.e. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral movement of the body on rail while the single moving body, i.e. SL, body has 2 nos. of a special anti-tilt bearing assembly fitted to the understructure which not only restrictslateral movement but also prevents SL from toppling. A Centralized locking arrangement is providedthrough Locking Stiffener mounted onto back of Single Last unit, i.e. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned. The Recess handle lock is of Godrej make & placed at a height of 940mm from ground level. The locking stiffener is made of 1.2mm thick conforming to IS:513. Hinged doors have Recessed Die cast Handle cum lock with 3way locking through a lever & shooting bolt. The nuts & bolts are galvanized / blackodized / Zn Plated. Label Holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be infixed into the aluminium extrusion.The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150–200-micron polythene is to be infixed.<br>Overall Dimensions of SL2 - S i n g l e l a s t 2 B a y P u s P h P u l l T y p Re ( U / C + F i I t t i n g s ) s Ch a l l b e 1 2 0 0 E m m ( W ) x 4 0 0 m m ( D ) x 2 1 0 6 m m ( H ) . T h e Construction shall be body shall have a main unit plus add on units (1,2,3,4,5). Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of minimum 40 microns. Shelf construction made of 0.7mm thick CRCA steel conforming to IS: 513 Gr.D or DD. Uniformly distributed load capacity of 60 Kg. Undercarriage shall have construction in welded frame CRCA sheet 2mm thick conforming to IS:513. The movements of the system shall be Push pull configuration (TYPE-P1/TYPE-P2): Movement of units achieved by pushing or pulling 'C' type plastic handle (mounted on each double & single movable units) & rigidly fixed at suitable height on body side. Each movable body also has an understructure with 4 nos. of antifriction ball bearings for rolling on channels. The twin moving body, i.e. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral movement of the body on rail while the single moving body, i.e. SL, body has 2 nos. of a special anti-tilt bearing assembly fitted to the understructure which not only restricts lateral movement but also prevents SL from toppling. A Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single Last unit, i.e. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned. The Recess handle lock is of Godrej make & placed at a height of 940mm from ground level. The locking stiffener is made of 1.2 mm thick conforming to IS:513. Hinged doors have Recessed Die cast Handle cum lock with 3 ways locking through a lever & shooting bolt. The nuts & bolts are galvanized blackodized / Zn Plated. Label Holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be infixed into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150–200-micron polythene is to be infixed.<br>Overall Dimensions of TM2 - Twin Mobile 2 Bay Push Pull Type (U/C + Fittings + Handle) shall be 915mm(W)x762mm(D)x2180mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS: 513. Each body shall have a main unit plus add on units (1,2,3,4,5). Finish shall be Epoxy polyester powder coated thickness of 40 microns. Shelf construction shall be made from CRCA steel 0.7 mm thick IS :513. Uniformly distributed load capacity of 60 Kg. Undercarriage shall have construction in welded frame CRCA sheet 2mm thick conforming to IS:513. The movements of the system shall be Push pull configuration (TYPE-P1/TYPE- P2): Movement of units achieved by pushing or pulling 'C' type plastic handle (mounted on each double & single movable units) & rigidly fixed at suitable height on body side. Each movable body also has an understructure with 4 nos. of antifriction ball bearings for rolling on channels. The twin moving body, i.e. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral movement of the body on rail while the single moving body, i.e. SL, body has 2 nos. of a special anti-tilt bearing assembly fitted to the understructure which not only restricts lateral movement but also prevents SL from toppling. A Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single Last unit, i.e. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned. The Recess handle lock is of Godrej make & placed at a height of 940mm from ground level. The locking stiffener is made of 1.2 mm thick conforming to IS:513. Hinged doors have Recessed Die cast Handle cum lock with 3 ways locking through a lever & shooting bolt. The nuts & bolts are galvanized / blackodized / Zn Plated. Label Holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be infixed into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150–200-micron polythene is to be infixed. // When the last unit is twin movable, hinged doors are provided for the end bodies, so in this case locking stiffener is mounted Oontohtweirn uEnint. g<birn> eer Preferred make: Godrej/Steelcase/Herman-Miller

Providing, supplying and placing of Foldable, Stackable, Cafeteria Tables. Overall Dimension -1800 x 750 x 750 Table top should be made of 25min thick. MDF OSR board (Bottom side in white color) as per IS:12406 PU coated on top side. Legs should be made by welding the combination of MS ERW round Tube 063.5 x 2mm thick as per IS: 7138, flanges made CRCA sheet of 1.6mm thick. and 1.2mm thick. as per IS 513 and inside plates made of HR 5mm thick. sheet as per IS:2062. The Assembly will be epoxy polyester powder coated of minimum thickness 45 microns. The Table top will fold upside at offset center pivot provided on support bracket which should be Aluminum alloy (ADC12) pressure die cast part coated with epoxy polyester powder coating of minimum thickness of 45 microns. Table top connected with spring loaded mechanism with pull handle made of MS ERW 016x1 2mm thick with an infix tube of 012.7x1.6mm thick tube as per IS:7138 coated with epoxy polyester powder coated of minimum 45- micron thickness to operate table top. Legs should be provided with casters of 065mm lockable type for ease of movement and can be locked when required at any position. Prefered make: Godrej/Steelcase/Herman-Miller

Providing, supplying and placing of Café Chair. The Seat and Back should be made up of injection moulded indoor grade PolyPropylene compound SEAT SIZE : 52.5 cm. (W) x 53.2 cm. (D) BACK SIZE : 51.6 cm. (W) x 40.5 cm. (H) The powder coated ( DFT 50±10 microns ) welded tubular frame should be made from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm MSERW tube. The shoes should be made of indoor grade PolyPropylene compound and snap fitted with tubular frame.<br>Overall Dimensions of Chair : Seat Height - 45.0 cm, Height - 84.5cm, Width-52.5 cm and Depth-55.8 cm. Prefered make: Godrej/Steelcase/Herman-Miller

M/s LUCRUM VENTURES (BID ID -2443937)

Sangi & Company (BID ID -2443940)