Widening and strengthening of 04 lane work from Bhanwarnath Temple to Kartalpur to Narauli on Bahraich Faizabad Azamgarh Road in Azamgarh District

Amount

Clearing and Grubbing Road land including uprooting rank vegetation, grass, bushes, shrubs, shaplings and trees girth upto 300 mm, removal of stumps of trees cut earlier and disposal of unservicable material and stacking of servicable material to be used or auctioned up to a lead of 1000 m including removal and disposal of Top organic soil not exceeding 150 mm in thickness, as per MoRTH specification No. 201 (Including all taxes but excluding GST)

Excavation for road work in soil with hydraulic excavator of 0.90 cum bucket capacity including cutting and loading tipper triming bottom and side slop in accordance with requirement of lime, grade and cross section and transporting of the embankment loctiong within all lift and lead. as per MoRTH specification No. 301 (Including all taxes but excluding GST)

Construction of Embankment with Material obtained from road side without lead) :- Construction of embankment with approved materials obtained from borrowpits with all lifts and leads, transporting to site , speading grading to required slope and compating to meet requirement of table 300-2 (without lead) (Data Book Sr. No. 3.16) material obtained from right way (Without lead) As per MoRTH specification No. 305 (Including all taxes but excluding GST)

Construction of Embankment with Material obtained from Borrowpits :- Construction of embankment with approved materials obtained from borrowpits with all lifts and leads, transporting to site, speading grading to required slope and compating to meet requirement of table 300-2 as per MoRTH specification No. 305 (from 5.00 Km. distance) (Including all taxes but excluding GST)

G.S.B Grade-1 Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density complete as per MoRTH specification No. 401 (Including all taxes but excluding GST)

Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density. As per MoRTH specification No. 406 (Including all taxes but excluding GST)

WMM+1% OPC Cement+3.5% Emulsion Providing, laying and spreading of graded stoneaggregate (WMM) after mixing with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying with 1% OPC cement and 3.50% emulsion in uniform single layer on sub base/subgrade and compacting with the road roller to achieve the desire density. As per MoRTH specification No. 406 as per direction of Engineer-in-charge. (Including all taxes but excluding GST)

Dense Graded Bituminous Macadam Grading-IInd Providing and laying dense graded bituminous macadam with 100 TPH batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505(A) complete in all respects. Using Bitumen (VG-40) Cha-258.200 to 259.800) (Including all taxes but excluding GST)

Dense Graded Bituminous Macadam Grading-IInd Providing and laying dense graded bituminous macadam with 100 TPH batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505(A) complete in all respects. Using Bitumen (VG-30) Cha-0.000 to 4.200) (Including all taxes but excluding GST)

Tack Coat IInd on Bituminous Surface Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor @ 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. As per MoRTH specification No. 503 (Including all taxes but excluding GST)

Bituminous Concrete Grading-IInd Providing and laying bituminous concrete with HotMix HMP 60-80 TPH using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 (B) complete in all respects. Using Bitumen (VG-40) Cha-258.200 to 259.800) (Including all taxes but excluding GST)

Bituminous Concrete Grading-IInd Providing and laying bituminous concrete with HotMix HMP 60-80 TPH using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507(B) complete in all respects. Using Bitumen (VG-40) Cha- 0.000 to 4.200) (Including all taxes but excluding GST)

Construction of subgrade and earthen shoulders Construction of subgrade and earthen shoulders with approved material obtained from borrowpits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement to Table 300-2 as per MoRTH specification No. 305 (with lead upto 5.00 km.). (Including all taxes but excluding GST)

RCC Grade M-30 (Case -1 using concrete mixer) Provinding and laying cement concrete M-30 grade excluding reinforcement complete as per drawing and techincal specifications. For New Jersy Type Devider (Including all taxes but excluding GST)

Painting of New Jersy with two coats synthetic enamel paint in all shades on new concrete surface after filling earth in median. As per direction of Engineer-in-charge (Including all taxes but excluding GST)

Supply of 80mm thick I Shapped mechanically interlocking cement concrete pavers block manufactured by high pressure & controlled vibration machine having plan dimension 200x(160+120mm) with minimum 5mm thick topping of O.P. cement mixed with 25% marble powder the compressive strength of concrete pavor block shall not be less than 30 PMa and 4.50 Kg./No. including cost of all materials, labour T&P etc. required for proper completion of the work as per direction of Engineer-in-charge. (Including all taxes but excluding GST)

Earth work in excavation Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material As per MoRTH specification No. 304 (Including all taxes but excluding GST)

PCC Grade 1:3:6 Plain cement concrete M15 in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and complacted by vibration including curing for 14 days. Foundation. As per MoRTH specification No. 2100 (Including all taxes but excluding GST)

RCC Grade M20 RCC Grade M20 (Using Concrete Mixer) As per MoRTH specification No. 1500, 1600, 1700 (Including all taxes but excluding GST)

HYSD Bar Supplying, fitting and placing HYSD bar reinforecement in super-structure complete as per drawing and technical specifications. As per MoRTH specification No. 1600 (Including all taxes but excluding GST)

Metal Beam Crash Barrier Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811. (Including all taxes but excluding GST)

TRAFFIC SIGNS - GIVE WAY Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67 upto date made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with PCC M-25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory/ Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer / Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67 upto date. Legends , letters , numerals and borders etc should be as per MoRTH specification No-801.(8.4) (Including all taxes but excluding GST)

TRAFFIC SIGNS - STOP Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity and high intensity prismatic grade Sheeting as per Type-XI vide clause-801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-25 grade cement conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawingas as per MoRTH Specification No. 801 (8.4)(i) (Including all taxes but excluding GST)

TRAFFIC SIGNS - MAXIMUM SPEED LIMIT Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity and high intensity prismatic grade sheeting as per type-iv 90 cm circular vide clause-801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mmx6 mm firmly fixed to th ground by means of properly dsignd foundation with M-25 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing as per MoRTH Specification No. 801 (8.4)(iv) (Including all taxes but excluding GST)

TRAFFIC SIGNS - HAZARD MARKER Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 mad of high intensity grade sheeting vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-25 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawing as per MoRTH Specification No. 801 (8.40) (Including all taxes but excluding GST)

Repeated Bars : Providing and laying of hot applied thermoplastic compound 5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 5 mm is exclusive of surface applied glass beads as per IRC:35 upto date. The finished surface to be level, uniform and free from streaks and holes. Free from streaks and holes and shall comply with requirements as per Table 800-9 of (MORTH SPECIFICATION) Thermoplastic Material when tested in accordance with ASTM D36/BS-3262-(Part 1) daylight Luminance shall be AASHTO M 249 for white 45o -65% min and for yellow 45% min., Drying time not more than 15 minutes, skin resistance not less than 45 as per BS-6044, material shall show no cracks on application to concrete blocks at Low Temperature, softening point 102.5oC ± 9.5oC as per ASTM D36 and yellowness index for white thermoplastic paint not more than 0.12 as per AASHTO M 249. Container of the thermoplastic material shall be clearly and indelibly marked with Name, Trade mark or other means of indentification of manufacturer, Batch No., Date of manufacturer, Colour, Maximum application temperature and maximum safe heating temperature. Glass beads shall meet the gradation requirement as per Table 800-10 of MORTH SPECIFICATION. The Glass beads shall have a minimum Reflective Index of 1.5 and 70% Roundeness. The Pavement Temperature shall not be less than 10oC during application of Hot thermoplastic paint. The Contractor shall furnish to the Engineer a copy of certified test reports from the manufacturer of the thermoplastic material/glass beads showing results of all test specified in MORTH SPECIFICATION and shall certify that the material meet all requirement of specification. (For Repeated Bar Marking) as per MoRTH Specification No. 803 (8.13) (Including all taxes but excluding GST)

TRAFFIC SIGNS - 50 X 60 CM SINGLE CHEVRON (NORMAL) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67 upto date made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with PCC M-25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory/ Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer / Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67 upto date. Legends , letters , numerals and borders etc should be as per MoRTH specification No-801.(8.40) (Including all taxes but excluding GST)

Road marking with Hot Applied Thermo Plastic Compount-Providing and laying of hot applied thermoplastic compound 2.5mm thick as per approved layout and design including reflectorising glass beads @ 250gms per sqm area, thickness of 2.5mm in exclusive of surface applied glass beads as per MORTH & H specification No. 803 The finished surface to be level, uniform and free from streack and holes rates to be inclusive of all labour and T&P etc complete required for proper completion of the work as per direction of E/I. as per MoRTH Specification No. 803 (8.13) (Including all taxes but excluding GST)

Reflective Raised Pavement Markers (Cat Eye/ Road Stud) Supply and fixing of raised pavement marker with Made of Plastic body of RPM/ Road Stud shall be moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (High-Impact Polystyrene) or Acrylonitrile Butadien Styrene (ABS) or Any other suitable material approved by the Engineer. The Marker shall support a load of 13,635 kg tested in accordance with ASTM D4280.The Reflective panels shall consist of number of lenses contatning single or dual prismatic cubes capable of providing total internal reflection of the light entring the lens face. Lenses shall be moulded of methyl methecrylate conforming to ASTM D788 or equivalent. The slop or retro-reflecting surface shall preferably be 35+/-5 degree to base and the area of each retro -reflecting surface shall not be less than 13.00 sq.cm. marker height shall not be less than 10 mm and shall not exceed 20 mm & Width shall not exceed 130 mm. The base of the marker shall be flat within 1.3 mm all road studs shall be legibly marked with the name , trade or other means of identification of the manufacture. epoxy installations, excess adhesive around the edge of the marker, excess adhesive on the pavement and adhesive on the exposed surfaces of the markers shall be immediately removed. The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel , to the Engineer . In addition , a two year warranty for satisfactory infield performance of the finished road marker shall also be given by the contractor who carries out the work of fixing of reflective road markers. In case the markers are displaced , damaged , get worn out or lose their reflectivity compared to stipulated standards , the contractor would be required to replace all such markers within 15 days of the intimation from the Engineer , at his own cost. The rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer- in-Charge. as per MoRTH Specification No. 804 (8.35) (Including all taxes but excluding GST)

TRAFFIC SIGNS - RUMBLE STRIP Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity and high intensity prismatic grade Sheeting as per Type-XI vide clause-801.37, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing (Including all taxes but excluding GST)

TRAFFIC SIGNS - STATE HIGHWAY ROUTE SIGN BOARD Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 mad of high intensity grade sheeting as per type-iv vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-25 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawing (Including all taxes but excluding GST)

Supply, fixing & Erection of built up Contilever Structure 6.00 M span comprising of one vertical post of 6.00 M heigh made up of 300 mm N.B. heavy class M.S. pipe as vertical member welded with 10mm M.S. plate at top & 12 mm M.S. bottom. The horizontal Truss shall comprise of 50 mm. dia heavy class M.S. pipe and 40 mm dia heavy MS pipe as bracing & 10 mm MS plate at bottom for fixing to vertical post as per structure design & drawing with one coat of steel primer and two coats of synthetic enamle paint. The work includes construction of RCC Foundation of size 0.90x0.90x1.50m of required depth as per site condition for built up structure including Earth work in excavation 100 mm thick lean concrete in 1:3:6 (cement coarse sand and 40 mm gauge stone ballast) and grade of Concrete RCC-M25 including supply and fixing of 25 mm dia Foundation Bolts 600 mm long as per provision of structure design including cost of reinforcement & shuttering. The lateral vertical clearances and complete. Installation work shall be as per relevant clauses of MoRTH specification section 800 and IRC 67 upto date complete in all respect. The rates shall include cost of design fabrication, supply, transportation. Local shifting Erection of Signage structure using crane, inclusive of all taxes etc. all T&P machine, material and labour required for proper completion of work as per direction of Engineer-in-charge (Including all taxes but excluding GST)

Supply & Fixing of M S Delineator made of Mild steel with pure polyester powder coating with the minimum thickness of powder coating of not less than 40 micron for protection against corrosion. The surface should be concealed so that there should not be any exposed surface without powder coating. Alternatively, these metal guide poles can be concealed with thermoplastic body. The posts shall have an ellipsoidal or circular design with the height of the pole shall be 800 to 900 mm above the ground with about 200 to 300 mm base which can be anchored onto the ground. Mild steeI Guide Poles shall conform to Type XI sheeting specifications as per IRC:67 upto date and ASTM D4956 which would ensure to obtain clear visibility of the road alignment during night time. The Retro reflective sheeting shall be tested for A certificate of aving the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory / Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer / Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67 upto date & Proof of the same Report shall be uploaded with quoting tender. The rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer-in-Charge as per MoRTH Specification No . 805 (8.15) (Including all taxes but excluding GST)

Providing & Fixing of 5th Kilometer stone precast as per direction of Engineer-in-charge. (Including all taxes but excluding GST)

Providing & Fixing of Ordinary Kilometer stone precast as per direction of Engineer-in-charge. (Including all taxes but excluding GST)

Providing & Fixing of Hectomeeter stone as per direction of Engineer-in-charge. (Including all taxes but excluding GST)

AMBE INFRAPROJECTS PRIVATE LIMITED (BID ID -5083897)

S. S. Construction Co. (BID ID -5077520)

SHIVANSH CONSTRCUTION (BID ID -5082383)