REPAIR TO PLASTERING, FLOORING, TILING, PLUMBING, SANITARY FITTINGS, DOOR, WINDOWS AND CERTAIN B/R WORKS AT ZONE A DOMESTIC AREA AT AF STN AMBALA UNDER GE (AF) AMBALA

Amount

Demolition of Brickwork or stone boulder masonary/PCC block masonary, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework & precast concrete articles and disposing off rubbish outside MD land complete all as specified and directed.

M&L for brick work with sub class B bricks , straight or curved on plan exceeding 6 m mean radius , built in cement mortor 1:6 complete all as specified and directed.

M&L for brick work with sub class'B' bricks,straight or curved on plan to any radius in half brick thick wall built in CM 1:4. complete all as specified and directed.

Taking down cement plastering of any thickness on brick, concrete or stone walls, partitions, ceilings etc including raking out joints, hacking for key, scrubbing down with water etc, and removing debris out side MD land complete all as specified and as directed.

M&L for 15 mm thick rendering on brick wall or concrete wall or any surface in cement mortar 1:6 on fair face/other than fair face and finishing the surface with even and smooth without using extra cement all as specified and as directed.

M&L for Rendering 15mm thick on fair face/other than fair face of brick work or concrete any surface in CM 1:4 finished even and smooth without using extra cement upto triple storey building, mixing with approved water proofing compound, for roof facia, chajjas, etc.and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed. NOTE:- (i) Height of the bldgs is Appx Up to 12 mtr. cost of necessary scaffolding and security provision of lablour shall be demeed to be included in the quoted rate. (ii) Supply only WPC will be measured and paid separately under relevant item of BOQ.

M&L for 5mm thick rendering on ceilings in cement mortar 1:3 and finishing the surface with even and smooth without using extra cement all as specified and as directed.

M & L for rough cast plaster incl 15 mm thick CM 1:3 on brick work or concrete surface complete all as specified in SSR Part -1 clause 14.22 complete all as specified . Note:Rough cast plaster finish shall be as follow :- After applying the under coat cement mortar 1:3 and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel aggreagte ( Which is generally of size between 6 to 12 mm depending on the texture required mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even . The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure the larger aggregate are throughly covered.complete all as specified and directed. Note : i) Area to be plastered may require to be carried out up to height of 15 m, cost of necessary scaffolding and security provision of lablour shall be demeed to be included in the quoted rate

M&L for Preparation of new or previously untreated plastered wall surfaces of any description not otherwise described and applying two coats of oil bound distemper over a coat of alkali resistant primer over and including 1 mm thick wall care putty, complete all as specified and as directed. Note : Quoted rate shall deemed to include for cost of wall care putty.

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceilings complete all as specified and directed

M&L for Preparation of newly plastered sufaces of walls and applying two coats of weather-proof antifungal exterior emulsion paint over a coat of alkali resistant primer,over wall care Putty upto triple storey building, complete all as specified and directed. Noted: Item shall be executed upto a height of 15.00mtrs. cost of necessary scaffolding and security provision of labour shall be deemed to be included in the quoted rates.

M & L applying two coats of cement based paint on newly plastered or unplastered wall surface including preparation of surfaces, complete all as specified and directed.

Taking down cement plaster and decayed concrete of any description, upto triple storey of building,Material & Labour for repair to chajjas/ roof projection with plain cement concrete 1:2:4 type B-0 using 12.5 mm graded mechanically crushed stone aggregates and dubbing out with 20 mm avereage thickness including necessary form work after taking down/ demolition of loose portion/ part/ particles & rendering with 5 mm thick in cement mortar 1:3 and finishing the exposed surfaces even & smooth using extra cement complete all as specified and as directed. Note:(i)cost of water proofing compound and necessary form work shall be deemed to be included in the quoted rates. (ii) Item shall be executed upto height of 12.00 mtr. cost of necessary scaffolding and security provision of labour shall be deemed to be included in the quoted rate.

M&L for Uprooting scrubs/plant/flora & fauna on wall girth not exceeding 100mm from brick wall by cutting holes into masonry/walls for digging out roots and dosing Sulfuric/Phenolic Acid as per manufacturer's instruction to burn deep rooted tree roots and making good the disturbed area with cement mortar in CM 1:3 using water proofing compound including necessary scaffolding upto a height of 12 metre complete all as specified and directed.” Note :- Item shall be executed upto a height of 12.00 mtr. cost of necessary scaffolding and security provision of labour shall be deemed to be included in the quoted rate.

Supply only integral water proofing compound complete all as specified and as directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing), removing serviceable tiles and disposing off debris to outside the MOD land complete all as specified and directed.

M&L for Non-skid joint free coloured ceramic tiles 7 to 8 mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm, as in floor set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match colour of tiles over and including 15mm thick screed bed of CM 1:6 complete all as specified and as directed.

M&L for glazed ceramic coloured printed tiles of size 450 x 300X 7mm as in dado set and jointed in neat cement slurry & pointed in white cement mixed with pigment to match with color of tiles over and including 10 mm thick rendering in cement motor 1:3 complete all as specified and directed.

M&L for coloured, non- skid joint free,edge cut, ceramic tiles,1st quality, 7 to 8 mm thick ,square/rectangular, polished, area of each tiles exceeding 0.18 but not exceeding 0.38 Sqm in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed or bedding layers in Cement Mortar 1:6, complete all as specified and directed.

All as per BOQ srl item No 19.00 here in above but in vertical surfaces with backing coat of 10 mm thick other than fair faces of wall in CM 1:4 complete all as specified and as directed.

M&L for Vitrified tiles flooring with Light shade 10 mm thick (Square / rectangular), tiles, area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L, for Vitrified tile, skirting/dado, light shade with 10 mm thick tiles of area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, on vertical rates as in skirting, dado, etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including backing coat of 10 mm thick CM 1:3 complete all as specified and as directed.

Demolition of Stone slabs & tiles of any description or thickness in floors, aprons etc. Laid, bedded & pointed in any mortar and removing debris outside MD land complete all as specified and directed.

M&L for 20mm thick Granite work (of any type) (table rubbed and premirror polished) in single piece in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in cement white (1:2) using marble dust with admixture of pigment to match the shade of granite, including making hole for gas pipe including half rounding the edges of granite, laid over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring not less than 18 to 20 mm thick (size of stone shall not less than 55cm x 55cm), 75mm wide white marble border around, laid over & including 15mm thick screed base in CM 1:6 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirrior finish with machine, complete all as specified and directed.

M&L for Machine cut Kota stone slab not less than 18 to 20mm thick as in riser of steps, skirting, dado and pillar laid over & including 15mm thick screed base in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine, complete all as specified and directed.

Demolition of cement concrete in ground floor and paving not exceeding 15cm below or above ground level removing debris outside MD land complete all as specified and directed.

M&L for 75mm thick PCC type D-2, (1:4:8) using 40mm graded mechanically crushed stone aggregate as in sub base of paving/Inter Locking , Hard standing Etc complete all as specified and directed.

M&L for 25 mm thick PCC 1 : 2 : 4 type B0 (using 12.50 mm graded mechanically crushed stone aggregate) as in sub floor rough to receive tile screed/bedding layer complete all as specified and directed

M&L for 40 mm thickness PCC 1:2:4 type B0 using 12.5 mm graded mechanically crushed stone aggregates as in floor finished even and smooth without using extra cement complete all as specified and directed.

M&L for 60mm thick machine pressed rubber moulded precast concrete M-35 interlocking coloured paver block any shape and size conforming to IS-15658-2006 with grey cement and pigment complete all as specified and directed.

M&L for Sand filling under floors including watering and consolidation all as specified as directed.

M&L for Chequered cement concrete commercial Tiles25CMX25CMX22mm /30cm x 30cm x 20 to 22mm thick of with grey cement and pigment set jointed and pointed in neat cement slurry in floors and cut and polished laid ande over 15mm Screed in CM 1:4 complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-1 using 20mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mt centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as specified and as directed. Notes :- (i) The unit rate quoted shall be deemed to include for providing the concrete in alternate bays not exceeding 3 Mtrs length,10 mm wide. (ii) 30 mm deep joints between the bays shall be provided which shall be filled with mastic filling with hot bitumen 85/25 grade and 1:2 mix volume.

M&L for cement concrete 1:2:4 type B0 ( using 12.5 mm graded mechanically crushed stone aggregate ) as in coping,kerb for water trough and the like including weathering , slightly rounded or chamfered agle and throating etc incl necessary form work etc complete all as specified and directed

100 mm thick plain cement concrete 1 : 2 : 4 type B2 (using20 mm graded mechanically crushed stone aggregate) as in hard standing laid in pannels including necessary form work, finished by spike rolling surfaces of concrete complete all as specified and as directed

Demolition of reinforced cement concrete of any description and in any position at level of 15 m high as in roof chajjas, fascia and parapet, RCC jalli any thickness and removing the debris out side MD land complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. rought finished surface concrete, complete all as specified and directed.

M&L for Mild steel TMT bars ,Fe 500 D, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M& L for RCC 1:2:4 Type B1 (normal mix) (using 20 mm graded mechanically crushed stone Aggregate) as in Beams, cantilivers, shelves, kitchen slabs incl formwork complete all as specified and directed

M&L for Precast RCC 1:2:4 type B1 (using 20mm graded mechanically crushed stone aggregate) as in cover slab of drain, culvert and the like set in CM 1:4 complete all as specified and directed.

M&L for brooming down surfaces of any description and applying one coat of white wash on old decorated surfaces of walls including preparation of old surfaces & filling cracks and holes etc complete all as specified and directed.

M&L for brooming down surfaces of any description and applying Two coat of white wash on old decorated surfaces of Ceiling including preparation of old surfaces & filling cracks and holes etc complete all as specified and directed.

M & L for for brooming down surfaces of any description and applying preparation of old wall surfaces, including preparation of old surfaces & filling cracks and holes etc and applying one coats of cement base paint complete all as specified and as directed.

M&L for Preparing the surfaces of old wall surfaces and applying one coat of distemper oil emulsion complete all as specified and directed

M&L for Complete removal of existing treatment and preparing the surfaces of walls plastered or unplastered and applying two coat of distemper oil emulsion over a coat of alkali resistent primer over putty any thickness. complete all as specified and directed Note : Quoted rate shall deemed to include for cost of wall care putty.

M&L for Preparation of old wooden surfaces and applying a coat of synthetic enamel paint over 10 cm width or girth complete all as specified and as directed.

M & L for painting of old steel surfaces of any description not otherwise described over 10 cm width or girth with one coats of synthetic enamel paint including preparation of surfaces etc complete all as specified and as directed.

M & L for complete removal of old/existing treatment including preparation of wall/Ceiling sufaces of any description and applying two coats of exterior grade weather proof paint water based over a coat of primer over any thickness birla care putty, on wall surfaces complete all as specified and directed. Note : (i) Height of the bldgs is Appx Up to 12 mtr incl Quoted Rates. cost of necessary scaffolding and security provision of labour shall be deemed to be included in the quoted rate. (ii) First the complete removal of existing treatment shall be done and got approved from Engr-in-charge. (iii) Final coat shall be done after getting approval of completion of priming coat from Engr-in-Charge

Taking down chowkats or frame without taking off shutter from the frame nnot exceeding 1.50 Sqm each from the frame and removing from site, including cutting holes for taking out hold fasts and making good disturbed portion in cement mortar 1:3, complete all as specified and as directed

Taking down chowkates / frame without taking off shutter exceeding 1.50 Sqm not exceeding 4 Sqm each. from the frame and removing from site, including cutting holes for taking out hold fasts and making good disturbed portion in cement mortar 1:3, complete all as specified and as directed

Taking down Shutters of any description exceeding 1 sqm and not exceeding 2 sqm each, complete all as specified and directed.

S&F Factory made solid PVC Chowkhat /Door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm thick rigid PVC foam sheet coloured, reinforced with 19x19mm MS square tube of 19 gauge including rubber gasket, PVC fasteners, screws, brackets as per SSR Part –II (2020) complete all as specified and as directed.

S&F for Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:),With Wood Free EPS with 2,4 or 6 raised panel design with 2 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawin complete all as specified and directed.

Repair/Rescuing, easing and adjusting wooden door shutter of any description without taking off shutter from the frame, area of shutter exceeding 1.00 Sqm but not exceeding 2.00 Sqm each, including making good the disturbed area as per existing, complete all as specified and directed.

S & F 35 mm thick plain framed panelled factory made shutters(two panel) with IInd class hardwood rail and style with lock rail and panel of 12 mm BWP commercial ply with commercial vaneer on both faces. The size of rail and style as per IS - 1003 Part - I , kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 35mm thick mm thick flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both side, complete all as specified & directed.. Note: The rates for flush shutters include for the provision of suitable blocks for taking mortice locks, latches, or other fittings complete all as specifed and directed.

S&F of Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 28 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant Fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws

S&F of Factory made single extruded WPC (Wood Polymer Composite) solid door Frames/Chowkhat of size 100 x 65 mm single rebate comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant Note: For WPC solid door frames, minus 5mm tolerance in Dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F of Factory made single extruded WPC (Wood Polymer Composite) solid door Frames/Chowkhat of size 125 x 65 mm double Rebate comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant, complete all as specified and directed. Note: For WPC solid door frames, minus 5mm tolerance in Dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F of providing 28 mm thick factory made 100% Solid WPC (Wood polymer Composite) Jointless gauzed and skeleton Shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ),alcium Carbonate andnatural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheetSingle Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured and an ISO 9001 -2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 Modulus of elasticity 850N/mm2and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. Fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws incl Aluminum Jali and Stainless wiremess as per required. complete all as specified and directed. Material test certificate and authentication should be compulsory provided by the manufacturing company

S & F 35mm thick IInd class hardwood glazed and skeleton shutters open rebated and prepared to receive gauge (without sash bars)edges of framing plain, chamfered or round fitted with cut and mitred beads for securing wire gauge sizes of members as specified in SSR Part-I section 8 clase 8.24(a) of shutters all as specified and as directed.

M&L for Mild steel framed work such as in doors or gates of angle, or tee sections with gusset plates, rails, braces, etc. completely drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging doors fittings (including of steel sheeting or other covering, running rails and guides) and handing also fastening and fixing complete Gde Fe 410 - W (Grade-E- 250) quality-A complete all as specified and as directed.ll as specified and directed.

Taking down boards of any description and any size as in shelves complete all as specified and directed.

S & F 19 mm thick fire retardant plywood BWR type including cutting, jointing, fixing with screws as in kitchen cabinet box type complete all as specified and as directed

S & F Decorative laminate type1, 0.90 to 1mm thick , of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions, complete all as specified and directed.

S&F 18/19mm thick one side prelaminated particle board, interior grade, with decorative choice laminate and fixed with screws to steel/timber frame work including provision of 6mm thick teakwood edging etc complete all as specified and directed

S & F teak wood beading of size 18/19 mm x 6 mm on the exposed/edges surfaces of the block board complete all as specified and as directed

S&F mild steel door shutter two leaves made out of 0.80 mm MS sheet, all round with frame of angle or other sections with gusset plates, rails braces etc , and leaves of 21 gauge MS sheet as per godrej pattern , with three way of locking arrangement with and includding brass lock with dupllicate keys , steel CP handle 200 mm long , drilled for fixing of steel sheeting or other covering door etc complete conforming to Fe 410-00 (Gde E-250) quality 'A' including one shop coat of red oxide primer over two coats of spray painting door with frame complete all as specified and directed.

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or FE 310-0, complete all as specified and directed.

M&L for Cutting holes brick walls built in cement mortar exceeding half brick thick wall but not exceeding one brick thick wall built in cement mortar for inserting hold fasts etc and making good the dismantled portion in plain cement concrete 1:2:4 type B1 & finished to match as per the existing finish complete all as specified and as directed. Note:- This item shall not be operated if hold fast holes are required at new location.

S&F machine crafted box type cabinet for kitchen using 18-19 mm thick PVC board both side laminated with and including all necessary fitting and fixtures to install wire basket , shutter shall be fixed by using full overlay MS clips on hinges high quality nickle plated satin finish size- 101 mm -150 mm ,02 Nos per leaf ,including all fittings ,channels , 150 mm s/s handles complete all specified and directed . NOTE:- (i)Wire basket shall be measured separetely. (ii)Front area of box shall be considered for payment purpose. (iii) Depth of box shall be equal to the width of cooking platform.

Su&F wire basket made of top quality 304 grade stainless steel, nickle chromium plated ( Ni 4%) of Approved design and pattern complete all as specified and directed.

S & F in fancy type stainless steel handle of size 100 mm long complete all as specified and as directed

S&F in 40mm dia, cupboard knobs fixed with nut, screw & washer of mild steel, bright finished

S&F steel window (box type) factory fabricated, double shutter (glazed and wire gauzed) with side hung shutters including pintle type hinges, steel handles fabricated type for each leaf duly welded, mild steel barrel tower bolts 150mm size (02Nos for each leaf) duly welded, with glazing bars dovetailed or welded including MS fillets, welding with and including 8mm dia Square guard bars with one shop coat of red oxide zinc chrome primer overall complete all as specified and as directed Notes: (i) Windows shall be fabricated as per CE Palam drawing No. TD-219 Sh 1/3 to 3/3 dated 02 Jan 2007 (updated up to date) and these drawings shall be referred at the O/o the GE (AF) Ambala (ii) Glazing and wire gauge will be measured and paid separately under respective items herein (iii) Any other sundries,Guard bars etc. as required at site shall be deemed to be included in the quoted rate

S&F powder coated aluminium anodised window(Three track sliding window, 02 shutters with glass and 01 shutter with wiremesh) made out hollow aluminium as mentioned below. Each shutter shall have 01 No. aluminium handle of 75mm size and 02 Nos aluminium tower bolt 150mm long. Window shall be glazed with 4.00mm thick tinted glass fixed with glazing clips, rubber beading and anodized aluminium beading and stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or stainless steel wire staple etc complete all as specified and as directed. Chowkhat bottom section size : 50.3mm X 26.0mm, 1.20mm thick Chowkhat top & sides section size : 50.3mm X 15.0mm, 1.00mm thick Shutter top & bottom rail section size : 101.60mm X 44.45mm, 1.50mm thick Shutter inner lock rail section size : 37.5mm x 15.0mm, 1.50mm thick Shutter side mid rail section size : 37.5mm x 15.0mm, 1.36mm thick Note :- (i) The weight of Aluminium sectons shall not be less than 0.55Kg/RM. (ii) Minimum thickness of anodization shall be 15 micron. (iii) The door/window shall be as per drawings/directions of Engingeer-in-charge and drawing may be reffered from GE office.

S&F Powder coated anodised aluminium door made out hollow aluminium section as mentioned below. Each door having 02 Nos disk or D type handle of 200 mm long , two Nos aluminium tower bolts of 200 size , one No mortice lock of six levers with key in duplicate regulated by double action hudrolic floor door spring (Make - Sandhu/Titz) shutters to be partly glazed with 5mm thick tinted glass and partly panelled with 12mm thick prelaminated particle board fixed with glazing clips, rubber beading/gasket anodised aluminium beading screws etc complete all as specified and as directed. Make :- Anodised aluminium section : HINDALCO/JINDAL/INDALCO Glass : SAINT GOBAIN/MODI GUARD/TATA CHOWKHATS SIZE : 100 X 44 X 1.60 MM THICK SHUTTERS VERTICLE STYLE : 100 X 44 X 1.60MM SHUTTERS LOCK RAIL : 150 X 44 X 1.60MM SHUTTERS BOTTOM RAIL : 200 X 44 X 1.60MM

S&F of aluminium partition wall, 60 micron powder coated sections, (minium thickness of powder coating shall be 50 microns) fabricated size of members 100 x 44.4 x 2.0 mm including making provision of opening etc; and all necessary cleats, panel inserts not more than 1.44 sqm and arrangement to receive with and including 5.5 mm thick sheet glass and 19 mm thick pre-laminated particle board with aluminium beading, glazing cleats and stainless steel screws rubber gaskets, beading etc; complete all as specified and directed. Note : Pre laminted Particle board and Glass and fitiings shall be deemed to be included in the quoted rate.

M&L for Preparation of newly steel surfaces of any description over 10 cm width or girth & applying two coats synthetic enamel paint complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and remove the debris outside of MoD land, complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality not exceeding 0.50 sqm each pane and fixed with oil putty or with wooden beading in square etc complete all as specified and directed.

All as per BOQ srl Item No.82.00 above but figured glass complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixed in repair complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixed with Flat Iron beading/nut & bolt and wooden beading in repair complete all as specified and directed.

S & F Aluminium anodized barrel tower bolts of extruded section, 150 mm long complete all as specified and directed.

S & F Aluminium anodized cast type handles 150mm long all as specified and as directed.

S&F Stainless Steel butt hinges medium weight of size 100 mm complete all as specified and directed.

S & F in door stopper of rubber and aluminium alloy body, 150 mm size fixed complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flaps (When open) 30 mm, complete all as specified and directed.

S & F magnetic ball catches of standard type fixed complete all as specified and as directed

S&F tubular curtain rail, stainless steel anodized 20 mm dia all as specified & as directed including taking down unserviceable rod/rail complete all as specified and directed.

S&F stainless steel type brackets suitable to hold the curtain rod with sofio phenol (Lotto) and wooden round blocks suitable to curtain rod of 20mm dia, decorative type fixed with suitable steel screws and PVC cleats, including taking down unservicable brackets complete all as specified and directed.

S & F in repairs of 300 mm mild steel ordinary rat tail, rod pattern springs including roller and roller plate complete incl welding complete all as specified and directed.

Taking down unserviceable GI tubing, supply and fixing new 15 mm bore Galvanized Iron tubing, medium grade, with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and as directed. Notes: i) Serviceable Taps, valves in any shall be removed before taking down pipe and same shall be re-fixed while providing new pipe, ii) Cutting chases for concealed piping shall be measured and paid separately under respective item.

Taking down unserviceable GI tubing, supply and fixing new 20 mm bore Galvanized Iron tubing, medium grade, with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and as directed. Notes: i) Serviceable Taps, valves in any shall be removed before taking down pipe and same shall be re-fixed while providing new pipe, ii) Cutting chases for concealed piping shall be measured and paid separately under respective item.

Refixing 20mm bore water tubing surface/concealed in same/new location after cleaning and application of bituminous paint on concealed portion of tubing including cutting & threading pipe and provision of additional fittings such as socket, tee, elbow, union (if required) complete all as specified and directed. Note : i) Taps, valves if any shall be removed before taking down pipe. ii) Cutting chases and making good shall be measured and paid separately

Cutting chases pinning in making good for brick walls to facing where required and pointing in cement mortar 1:3 to ends or edges of concealed water tubing and similar work including making good cutting not exceeding 10CM girth. Complete all as specified and directed.

S & F in repair 15 mm CP cast copper alloy bib taps fancy type screwed down, screwed for iron pipe or for brass ferrule including taking down old bib taps complete all as specified and as directed.

S & F aluminium alloy, anodised, sliding door bolt with hasp, staple bolt type and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long complete all as specified and as directed.

S & F 15 mm pillar taps, cast copper alloy fancy type , chromium plated screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe including taking down old pillar taps complete all as specified and as directed.

S & F in repairs CP fancy type angle cock,/stop cock cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repair chromium plated overhead shower rose 125mm dia with swivel joints with and including overhead shower arm 230mm with wall flange , complete all as specified and directed by GE.

S & F in repairs, 15mm Stop valves (concealed), fancy type with CP wall flanges, chromium plated, cast copper alloy with long shank and exposed part kit with fittings sleeve, operating lever concealed part screwed both ends for iron pipe or for unions, including making good the disturbed portion matching with adjacent surfaces,complete all as specified and as directed

S&F in repair, Chromium plated Wall mixer with bend pipe for overhead shower with built-in non return valve with CP wall flanges, fixed in repair complete all as specified and directed by GE

S&F in repair Centre hole wash basin mixer for wash hand basin complete all as specified and directed

S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 mtr tube & hook (braded Tube) and ABS valve including making connection and fixed in position complete all as specified and directed.

S&F in repair Single towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat etc complete all as specified and directed.

S & F in repair PVC connecting pipe 600mm long 15 mm dia both end having brass coupling nut and PVC washer all as specified and as directed.

S&F Vitreous china white wash down water closet pan (pedestal pattern) with PP soft closing seat cover, hinges, fixing accessories set (excluding flushing cistern and flush pipe), including UPVC (SWR) ‘P’ or ‘S’ trap and connection to drain (or outgoing pipe) and to flush pipe, antisyphonic pipe fixed in repair including dismantling existing water closet etc complete all as specified and directed

S&F Vitreous china White Squatting Orissa Pattern pan of size 580x440mm, including UPVC ‘P’ or ‘S’ trap, front or back inlet and integral foot rests and making connection to trap and to flushing pipe, anti syphonic pipe, fixed in repair including dismantling existing squatting pan and making good to disturbed floor, complete all as specified and directed.

S& F Vitreous China wash basin, white, flat back, size 550x400mm excluding waste, chain and plug and porcelain stopper but including brackets, including Waste coupling of PTMT(half or full threaded) (Minimum weight 32mm-45gms/40mm-60 gms) with 32mm bore PVC waste pipe minimum 800mm long with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed in repairs complete all as specified and as directed.

S&F in repairs, PVC valve less, syphonic action type, white colour flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including jointing with new PVC long / short flush bend and making good to the disturbed surfaces complete all as specified and as directed.

S & F in repair stainless steel sink with draining board, made out of 1.00 mm thick sheet for kitchen with plugs, waste pipe and washer’s including cast iron cantilever brackets, connecting union etc over all size 915 mm x 460 mm with bowl size 410 x 330 x 160 mm including taking down old steel sink all as specified and as directed.

S&F in repairs stainless steel plate rack of 0.63mm thick sheet, size 31''x36''x10'' complete all as specified and as directed.

S&F in repair PVC waste pipe 32mm bore not less than 800mm long complete all as specified and direceted

Dismantling of water tanks of 1000 litres capacity from roof top and supply and fixing Rotational moulded polyethylene water storage tanks (triple layered) of 1000 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

Dismantling of water tanks of 500 litres capacity from roof top and supply and fixing Rotational moulded polyethylene water storage tanks (triple layered) of 500 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

S&F in repair Ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of dia 20 mm bore complete all as specified and directed .

S&F in repair for 15 mm dia Gun-metal, globe or gate valves/, with iron wheel head, screwed both end for iron pipe and fixed, complete all as specified and directed.

M & L in repair Gun metal Gate valves 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed including cutting the old pipes as in repair complete all as specified and directed

S&F in repair Corner glass self assembly consisting of 5.5mm thick sheet glass self 25cm wide with chromium plated bracket guard and fixed with CP screws and wood cleats with wall complete all as specified and directed.

S&F in repair glass shelf assembly consisting of 5.5mm thick sheet glass self 12cm wide with chromium plated bracket guard and rail 60cm long and fixed with CP screws and wood cleats with wall complete all as specified and directed.

Taking down eaves gutters, soil / waste / vent pipes / rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., Supply and fix, UPVC (SWR) pipes 110 mm dia, type B (conforming to IS 13592) single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil / waste / vent pipes with Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and as directed. Note :- Provision of necessary scaffolding for replacing defective pipes shall deemed to be included in quoted rates, and nothing extra will be admissible in this regards.

Taking down eaves gutters, soil / waste / vent pipes / rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., Supply and fix, UPVC (SWR) pipes 75 mm dia, type B (conforming to IS 13592) single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil / waste / vent pipes with Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and as directed. Note :- Provision of necessary scaffolding for replacing defective pipes shall deemed to be included in quoted rates, and nothing extra will be admissible in this regards.

S & F PVC (SWR) bends any radius 75 mm dia of bore with access door, including taking down old bends complete all as specified and directed.

S & F PVC (SWR) branch piece single (single T)equal of bore 75 mm dia with access door in repairs complete all as specified and directed.

S & F PVC (SWR) branch piece single (single T) equal or unequal of bore 110 mm dia, with access door in repairs complete all as specified and directed.

S&F UPVC (SWR) bends any radius, 110mm bore with / without access door, complete all as specified and directed.

S&F in repair PVC floor trap/Nanhi Trap with plain/single hole CP grating including jointing to waste pipe in cement joint, of outlet 75 mm.dia,complete all as specified and directed.

M & L for welding in repairs to steel windows / doors exceeding 2.5 cm but not exceeding 5.00 cm in length and thickness of metal to be welded not exceeding 6mm complete all as specified and as directed.

S& F GI spout 40 mm dia medium grade to be embeded in sunken floor complete all as specified and directed.

M&L in repairs Drawer channel of length 0.50m and not exceding 1.00mtr for modular kitchen, complete all as specified and directed.

Disconnecting existing PVC water tank of capacity exceeding 500 ltr but not exceeding 1000 ltr fixed on roof by setting aside (or lowering, if required) for cleaning and removing all scale and dirt from tanks and from mouths of circulating pipes etc and hoisting/refixing/reconnecting in same/new position including writing date of cleaning on each tank with white paint, height/size of letters/figures not less than 10cm in height, and refixing existing serviceable ball valves complete all as specified and directed.”

S&F butt hinges, medium weight cold rolled mild steel 100 mm size welded to angle iron frames or fixed with screws to wooden frames complete all as specified and as directed.

S&F in repairs PVC Mirror cabinet of size 350 x 450 mm complete all as specified and as directed.

M&L for two coats of synthetic enamel paint over one coat of red oxide/zinc chrome primer on new steel surfaces of any description over 10 cm width or girth including preparation of surfaces complete all as specified and as directed..

S&F steel ventilator with top hung shutter including hinges peg stay to receive glazing or gauzing and one coat of primer including fixing of hold fast size 25 x 5 mm of flat iron etc complete all as specified and directed.

S&F in repairs mortice lock 100mm size Mortice lock (four levers), vertical type, brass body including handles”wooden doors or aluminium doors including screwing and fixing complete all as specified and as directed.

S & F in repair Chromium plated fancy type brass soap dish with wall hook complete all as specified and as directed.

S&F in repair Stainless steel toilet paper holder with flap guard, fixed to wall with CP brass screws and PVC cleat, complete all as specified and directed by GE.

M & L for applying two coats of synthetic enamel paint over a coat of pink primer including preparation of previously untreated or new wooden surfaces exceeding 10 cm in width or girth complete all as specified and as directed.

Anil jindal and sons (BID ID -3372865)

M/S NOBEL CONSTRUCTION CO. (BID ID -3371602)

AMIT LAMBA (BID ID -3380388)