Providing Lift Water Supply Scheme to Schedule Caste Populated villages Mand Bhogarwan Palakh Rajgir Surarwan etc in Tehsil Indora Distt. Kangra Himachal Pradesh

Amount

Supply of horizontal spindle horizontal radial split casing/and suctions (back pull out arrangement) Single/double/multistage centrifugal pumps or combination of pumps in series/parellel of KSB/Mathur & Platt/Jyoti/ Kirloskar/BE/Maxflow/Beaconweir Sabar make conforming to BIS1520-1980) pump ( Latest with up to to date amendments, read with BIS: 9137-1978 (latest edition) suitable for lifting water of under mentioned characteristics with bronze/Suitable alloy, priming funnels, casing ring and shaft motor of bronze, shaft of steel grade ASA-410 with cast iron casing coupled directly through a flexible coupling on a common MS/Cast steel plate (base plate from the principal manufacturer of pumping set) to coupling sliperring squirrel cage screen protected drip proof electric induction motor/ motor of standard make such as Kirloskar/ NGEF/Cromption/Siemen/Jyoti/BHEL/GEC/ABB conforming to BIS 325-1978) read with BIS 900-1972( latest with upto date ammendments) it should include the cost of bearings, nuts & bolts,m painting etc. and shall be and suitable for operation on the date given below: Centrifugal pumping machinary ( Zone- 2nd) 2 Set of 30 HP

Location of the site of installation of machinery. The site is located at a distance of 28 KM from Pathankot (Chakki) Railway Station by road and 1.00 Kms by head load

The Altitude of place of in which pumping set is intended to work Altitude of place - 100 metres above MSL

Type of current. AC Three phase supply with frequency of 75 cycle 75 second

Rate Voltage 415+ 10%

Type of water (Raw/Treated) Clear water for collection tank

Characteristic of water

a)Ambient Temperature dig.c

b)Turbidity NTU upto 50 NTU

c)Hardness260Mg/Ltrs(as CaCO3) Mg/Ltr

d) PH 6.50 to 8.50

e) TDS 540 PPM

f) Other

Depth of collection tank 3.00 metres

L.W.L. in Tank/collection tank 100.00 metres

R.L. of pump shaft/ centre Axis 100.00 metres

Suction head 113.40 metres

Discharge level of highest point 213.40 metres

No. of pumps required 2 No. Pumps (one will act as standbye)

Capacity 8.40 LPS for each pump

Total head in metres 127.17 metres

Length of Rising main 1220.00 metres G.I. (M) existing

Dia of Rising main 125mm dia G.I. medium pipe 4.80mm thick

Pumping hours per day 8.00 hours

Limits of pump operation In the competiion Range of (-) 75%

HP of motor/Drive unit Required BHP of pump at (+) 10% & (-)15% of total head or BHP with following margins/multiplying factor at duty point, whichever is higher

a) Upto 2 HP = 1.5 d) 10 to 20 HP = 1.20

b) 2 to 5 HP - 1.4 e) 20 to 100 HP 1.15

c) 5 to 10 HP = 1.3 f) Above 100 HP = 1.10

R.P.M. of pumping set. 2900 RPM

Test run. 8 Hours continueously for 7 days

NPSH available Metres

Supply , Installation, Testing and Commissioning of Fully Automatic LT Panel for Submersible pump made out of 16 Gauge sheet powder coated dust and veremin proof wall mounted and front opering door type switch board with copper insulated wiring suitable to operate 2 No. pump of rating 30 HP automatically through Variable Frequency Drive Starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and off command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. Reputed make.

Providing and fixing of double flanged cast iron Sluice valve having size one dia higher than pump size to delivery Pump class PN 1.0 of Kirloskar/Kilburn/Leader make conforming to BIS- 14846-2000 latest with upto date ammendments having seat pressure 10.20kg/ cm2 complete in all respect. Within all leads and lifts. (Suction side), The size & class of valve shall be specified by the tenderer.

Providing and fixing of Kirloskar/ Kilburn/Leader make Cast iron class PN 1.60 double flanged swing check type reflux valve having bypass arrangement equal to dia of Risng main i.e. 125mm shall be suitable for withstanding nominal seat pressure of 16.32 Kg/Cm2 as per BIS 5312-1984 Part-II .The size & class of valve shall be specified by the tenderer.

Provioding and fixing of cast iron double flanged NRV valve ----mm dia of Kirloskar/Kilburn/Kartar/Leader make of size & class PN-1.6 having one size higher to delivery size of pump and capable of with standing nominal seat pressure of 16.32 kg/cm2. confirming to BS-14846-2000(latest addition) (latest with upto date ammendments).The size & class of valve shall be specified by the tenderer. (Delivery side)

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/ Grandlay! Gloster make conforming to BIS 1554 (Part I)-1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities. In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost.

On supply side of 3½ core coper cable 10.00 mm² (From HPSEB Meter to Switch & Starter).

On motor side 3 core flat joint less copper cable of size 6.00 mm² (From Switch & Starter to Motor) pump installed in the bore.

Supply of standard make 100 mm dia circular/square dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock.copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments.

Laying, Jointing of G.I. pipe considering site requirements and having appropriate size in accordance with the delivery size of pumping set. The pipe shall conform to relevant BIS codes & capable of with standing the feild test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tapers/ reducers, flanges, rubber gaskets 3mmthick, nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer-in-Charge. The pipe material shall conform to relevant BIS Code and capable of with standing FTP equal to 1.5 times the operating pressure the complete arrangement shall compromise of

Suction pipe ---- mm dia (size to be specified by the tenderer)

Delivery pipe ---- mm dia (size to be specified by the tenderer)

Common header 125 mm dia (size to be specified by the tenderer)

Providing and lying double loop earthing with coper plate 600x600 x3 thick electrode and copper strip of 25x3 complete including providing of material such as charcoal, common salt. Gl pipes, thimbles, nuts & bolts, digging of pits, Copper /GI wire/ Strips of required capacity conforming to BIS 8034-1978 latest with upto date ammendments for above motor & other electriacl equipments including all civil works.

Errection of all equipment including Cost of Tees bends Taper & any other fitting required as per site Condintion & as per Direction of Engineer in Charge.

Supply of submersible pumping set of Kirloskar/Kilburn/Clama/Crompton/KSB make conforming to BIS; 8034-1976 latest suitable for lifting clean water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacturer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The pump shall be suitable for operation on data given below:- Submersible pumping machinery ( ZONE- 3rd) 2 Set of 25 HP

Total Head 77.42 Mtrs

Discharge required from each pump. 12.36 LPS

No. of pump required 2.00 No. ( 1 No. Stand bye )

Location of the site of installation of machinery. The site is located at a distance of 15 KM from Pathankot Railway station by road & 0.100 KM on head load (for the installation of both machineries.

The Altitude of installation. The altitude of place is 465.00 mtrs above MSL

Type of current. AC Three phase supply with

Rate Voltage 415+ 10%

Type of water and its source Clear water from Tube Well

Charactristics of water. -

a)Ambient Temperature dig.c 20 dig. C

b)Turbidity NTU 113 NTU

c)Hardness260Mg/Ltrs(as CaCO3) 540 Mg/ltr

d) PH 6.5 to 8.5

e) TDS 540PPM

f)Other -

Depth of Tube- Well 160.00 mtrs

LWL in Tube-Well 80.00 mtrs.

Center line level of Pump 80.00 mtrs.

Discharge level of highest point 154.00 mtrs

Static head in Mtrs 74.00 mtrs.

Length of R/Main 20 mtrs.

Dia of Rising main 150 MM G.I. pipe (M) 4.80mm thick

No of working hours per day 8 Hours

Limit of pump operation. (-) 15 % (+) 10% of total head

R.P.M. of pumping set. 2900 RPM

Test run. 8 Hours continueously for 7 days

Supply , Installation, Testing and Commissioning of Fully Automatic LT Panel for Submersible pump made out of 16 Gauge sheet powder coated dust and veremin proof wall mounted and front opering door type switch board with copper insulated wiring suitable to operate 2 No. pump of rating 25 HP automatically through Variable Frequency Drive Starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and off command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. Reputed make.

Providing and fixing of Kirloskar/ Kilburn/Leader make Cast iron double flanged swing check type reflux valve 125mm dia class PN 1.6 having bye pass arrangement ( to be provided on delivery side) of size of one size higher than the delivery size of pump and shall be suitable for withstanding nominal seat presure of 16.32 Kg/Cm2 confirming to BIS 5312-1984 Part-I .The size & class of valve shall be specified by the tenderer.

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/ Grandlay/ Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles ,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost.

On supply side of 3½ core coper cable 10 mm^2 ( From HPSEB Meter to Switch & Starter).

On motor side 3 core flat joint less copper cable of size 4 mm^2 ( From Switch & Starter to Motor) pump installed in the bore.

Supply of standarad make 100 mm dia circular/square dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock,copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments.

Laying, Jointing and Testing of G.I./MSERW pipe considering site requirements and having appropriate size in accordance with the delivery size of pumping set . The pipe shall conform to relevant BIS codes & capable of with standing the feild test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tapers/ reducers, flanges, rubber gaskets 3mmthick, nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer-in-Charge. The pipe material shall conform to relevant BIS Code and capable of with standing FTP equal to 1.5 times the operating pressure the complete arrangement shall compromise of

Delivery Pipe 100mm dia G.I. medium class 4.50mm thick.

P/L double loop earthing with copper plate 600x600x3mm thick electrode complete with material such charcoal, common salt, GI pipes, thimbles, nuts & bolts, digging of pits, GI wiring & 25x5mm copper strips of required capacity conforming to BIS 3043-1987 latest with upto date ammendments for above motor & other electrical equipment.

Errection of all equipments including cost of tees, bends tapers & any other fittings required as per site conditions & as per directions of Engineer-in-Charge.

Supply of submersible pumping set of Kirloskar/Kilburn/Clama/Crompton/KSB make conforming to BIS; 8034-1976 latest suitable for lifting clean water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacturer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The pump shall be suitable for operation on data given below:- Submersible pumping machinery ( ZONE- 4th) 2 set of 20 HP

Total Head 207.63 Mtrs

Discharge required from each pump. 3.54 LPS

No. of pump required 2.00 No. ( 1 No. Stand bye )

Location of the site of installation of machinery. The site is located at a distance of 15 KM from Pathankot Railway station by road & 0.100 KM on head load (for the installation of both machineries.

The Altitude of installation. The altitude of place is 465.00 mtrs above MSL

Type of current. AC Three phase supply with

Rate Voltage 415+ 10%

Type of water and its source Clear water from Tube Well

Charactristics of water. -

a)Ambient Temperature dig.c 20 dig. C

b)Turbidity NTU 113 NTU

c)Hardness260Mg/Ltrs(as CaCO3) 540 Mg/ltr

d) PH 6.5 to 8.5

e) TDS 540 PPM

f)Other -

Depth of Tube- Well 160.00 mtrs

LWL in Tube-Well 100.00 mtrs.

Center line level of Pump 100.00 mtrs

Discharge level of highest point 148.20 mtrs

Static head in Mrs 48.20 mtrs.

Length of R/Main 3850 mtrs.

Dia of Rising main 65 MM G.I. pipe (M) 3.60mm thick

No of working hours per day 20 Hours

Limit of pump operation. (-) 15 % (+) 10% of total head

R.P.M. of pumping set. 2900 RPM

Test run.8 Hours continueously for 7 days

Supply , Installation, Testing and Commissioning of Fully Automatic LT Panel for Submersible pump made out of 16 Gauge sheet powder coated dust and veremin proof wall mounted and front opering door type switch board with copper insulated wiring suitable to operate 2 No. pump of rating 20 HP automatically through Variable Frequency Drive Starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and off command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. Reputed make.

Providing and fixing of Kirloskar/ Kilburn/Leader make Cast steel double flanged swing check type reflux valve...mm dia class ASA-150 having bye pass arrangement ( to be provided on delivery side) of size of one size higher than the delivery size of pump and shall be suitable for withstanding nominal seat presure of 21.00 Kg/Cm2 confirming to BIS 1868API-600 .The size & class of valve shall be specified by the tenderer.

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/ Grandlay/ Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles ,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost.

On supply side of 3½ core coper cable 6 mm^2 ( From HPSEB Meter to Switch & Starter).

On motor side 3 core flat joint less copper cable of size 4 mm^2 ( From Switch & Starter to Motor) pump installed in the bore.

Supply of standarad make 100 mm dia circular/square dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock,copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments.

Laying, Jointing and Testing of G.I./MSERW pipe considering site requirements and having appropriate size in accordance with the delivery size of pumping set . The pipe shall conform to relevant BIS codes & capable of with standing the feild test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tapers/ reducers, flanges, rubber gaskets 3mmthick, nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer-in-Charge. The pipe material shall conform to relevant BIS Code and capable of with standing FTP equal to 1.5 times the operating pressure the complete arrangement shall compromise of

Delivery Pipe 50 mm dia G.I. medium class 3.60mm thick

P/L double loop earthing with copper plate 600x600x3mm thick electrode complete with material such charcoal, common salt, GI pipes, thimbles, nuts & bolts, digging of pits, GI wiring & 25x5mm copper strips of required capacity conforming to BIS 3043-1987 latest with upto date ammendments for above motor & other electrical equipment.

Errection of all equipments including cost of tees, bends tapers & any other fittings required as per site conditions & as per directions of Engineer-in-Charge.

KULDIP GOVT. CONTRACTOR

KULDEEP DOGRA