Special repair to DDM Residence at HRTC workshop Bilaspur, Distt. Bilaspur (HP)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within all lead : Of area 3 sq.(Three square) metres and below, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Sal wood, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm (Twety five to Forty milimeter) thick : Ply wood 5(Five) ply, 9 mm (Nine milimeter) thick Decorative plywood one side decorative veneer and commercial veneer on other face (Type 1) conforming to IS 1328 BWR Type, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm (One point four milimeter) in both directions with wire of dia 0.63 mm (Zero point sixty three milimeter), for doors, windows and clerestory windows with hinges and necessary screws : 35 mm (Thirty five milimeter) thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm (Four point zero milimeter) thick glass panes, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm (Two hundred fifty into Sixteen milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150x10 mm (One hundred fifty into Ten milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm (One hundred twenty five milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg (Thirty six Kilogram to Eighty Kilogram) and door width from 701 mm to 1000 mm (Seven hundred one milimeter to One thousand milimeter ), with double speed adjustment with necessary accessories and screws etc. complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

52 mm (Fifty two milimeter ), thick cement concrete flooring with concrete hardener topping, under layer 40 mm (Forty milimeter ) thick cement concrete 1:2:4 (One cement isto Two coarse sand isto Four graded stone aggregate) 20 mm (Twenty milimeter ) nominal size and top layer 12mm (Twelve milimeter ) thick cement hardener consisting of mix 1:2 (One cement hardener mix isto Two graded stone aggregate) 6 mm (Six milimeter ) nominal size) by volume, hardening compound mixed @ 2 (Two) litre per 50 kg (Fifty Kilogram )of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and laying in situ five course water proofing treatment with APP (Atactic Polypropylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd layer of roofing membrane APP modified Polymeric membrane 2.0 mm thick of 3.00 Kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 (Twenty) micron HMHDPE film. 5th, the top most layer shall be finished with brick tiles of class designation 10 (Ten) grouted with cement mortar 1:3 (One cement isto Three fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm (Twelve milimeter ) layer of cement mortar 1:3 (One cement isto Three fine sand) and finished neat (item of laying brick tiles shall be paid for separately), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (One cement isto Three fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm (Twelve milimeter ) layer of cement mortar 1:3 (One cement isto Three fine sand) and finished neat: With common burnt clay F.P.S. (non modular) brick tiles of class designation 10, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing 10 mm (Ten milimeter ) thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge : In flooring on a bed of 10 mm (Ten milimeter ) thick mortar 1:4 (One acid proof cement isto Four coarse sand) Acid and alkali resistant tile, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm (Twelve milimeter) thick bed of cement mortar 1:3 (One cement isto Three coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Repairs to plaster of thickness 12 mm to 20 mm (Twelve to Twenty milimeter) in patches of area 2.5 sq. (Two point five ) meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in- Charge. With cement mortar 1:4 (One cement isto Four coarse sand) , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and applying white cement based putty of average thickness 1 mm (One milimeter) of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer’s specification. Two or more coats on new work, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Finishing walls with water proofing cement paint of required shade : Old work (one or more coats @ 2.20 kg/10 sqm) complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall : 15 mm (Fifteen milimeter) dia nominal bore, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall : 25 mm (Twenty five milimeter) dia nominal bore, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion, (i) Single socketed pipes. 110 mm(One hunderd ten milimeter) diameter, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion, (i) Single socketed pipes. 75mm (Seventy five milimeter) diameter, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion. Bend 87.5° : 110 mm (One hunderd ten milimeter) bend, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion. Bend 87.5° : 75 mm (Seventy five milimeter) bend, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion. Single tee without door : 110x110x110 mm (One hunderd ten into One hunderd ten into One hunderd ten milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion. Single tee without door : 75x75x75 mm (Seventy five into Seventy five into Seventy five milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion. Single tee with door : 110x110x110 mm (One hunderd ten into One hunderd ten into One hunderd ten milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion. Single tee with door : 75x75x75 mm (Seventy five into Seventy five into Seventy five milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion. Coupler: 110 mm (One hunderd ten milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion. Coupler: 75 mm (Seventy five milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm (Fifteen milimeter) nominal bore, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm (Twenty five milimeter) nominal bore, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm (One hunderd milimeter) inlet and 100 mm (One hunderd milimeter)outlet Sand Cast Iron S&S as per IS: 1729, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm (One hunderd milimeter) sand cast Iron P or S trap, 10 (Ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing wash basin with C.I. brackets, 15 mm (Fifteen milimeter) C.P. brass pillar taps, 32 mm (Thirty two milimeter) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 550x400 mm (Five hunderd fifty into Four hunderd milimeter) with a pair of 15 mm (Fifteen milimeter) C.P. brass pillar taps, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing 600x450 mm (Six hunderd into Four hunderd fifty milimeter) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (Six milimeter) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm (Fifteen milimeter) nominal bore, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing PTMT grating of approved quality and colour. Circular type 100 mm (One hunderd milimeter) nominal dia, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm (One hunderd thirty eight milimeter), breadth 102mm (One hunderd two milimeter), height of 75mm (Seventy five milimeter) with concealed fitting arrangements, weighing not less than 106 gms. (One hunderd six Grams), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (One cement isto Four coarse sand) C.I. cover with frame (light duty) 455x610 mm (Four hunderd fifty five into Six hunderd ten milimeter) internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg (Twenty three kilogram) and weight of frame 15 kg (Fifteen kilogram) ), R.C.C. top slab with 1:1.5:3 mix (One cement isto One and half Fine sand isto three graded stone aggregate) 20 mm (Twenty milimeter) nominal size, foundation concrete 1:5:10 (One cement isto Five fine sand isto Ten graded stone aggregate) 40 mm (Forty milimeter) nominal size, inside plastering 12 mm(Twelve milimeter) thick with cement mortar 1:3 (One cement isto Three coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm (Four hunderd fifty five into Six hunderd ten milimeter and Forty five Centimeter) deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Please Enable Macros to View BoQ information