Construction work of control Room at saryu barrage

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. But excluding Cost of GST.

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. But excluding Cost of GST.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. But excluding Cost of GST.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. But excluding Cost of GST.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. But excluding Cost of GST.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) But excluding Cost of GST.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). But excluding Cost of GST.

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources). But excluding Cost of GST.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: All works upto plinth level Concrete Of M25 Grade with minimum cement contet of 330 kg/ cum of Ultratech/ACC Suraksha/JK Super Strong Brand Ordinary Portland Cement. But excluding Cost of GST.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: All work above plinth level upto Floor v level Concrete Of M25 Grade with minimum cement contet of 330 kg/ cum of Ultratech/ACC Suraksha/JK Super Strong Brand Ordinary Portland Cement. But excluding Cost of GST.

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers. But excluding Cost of GST.

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts. But excluding Cost of GST.

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform. But excluding Cost of GST.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing ,using 18 gauge binding wire in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.Brand (Make Sail&Tata). But excluding Cost of GST.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing ,using 18 gauge binding wire in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.Brand (Make Sail&Tata). But Excluding cost of GST.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. But Excluding cost of GST.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand). But Excluding cost of GST.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand), But Excluding cost of GST.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand). But Excluding cost of GST.

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). But Excluding cost of GST.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 8mm thickness of Kajaria/Somany /Johnson make, in all colours, shades except burgundy, bottle green, black of (300 x 600 mm) size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. But Excluding cost of GST.

Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. But Excluding cost of GST.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. But Excluding cost of GST.

Providing Sal wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length. But Excluding cost of GST.

Providing and fixing 35 mm thick panelled or panelled and glazed shutters of second class teak wood for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. But Excluding cost of GST.

Providing and fixing 30 mm thick panelled or panelled and glazed shutters of second class teak wood for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. But Excluding cost of GST.

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. But Excluding cost of GST.

Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge. But Excluding cost of GST.

Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). 18 mm thick. But Excluding cost of GST.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Brand(Make Sail & Tata). But Excluding cost of GST.

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. But Excluding cost of GST.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40mm thick flooring. But Excluding cost of GST.

Providing and laying vitrified floor tiles in 600x1200 mm size 10-12 mm thickness with water absorption's less then 0.080% and conforming to IS: 15622 of Kajaria/Somany/Johnson make in all colours and shades laid on 20 mm thick cement morter 1:4 including grouting the joints with white cement and matching pigments etc. including all cost of material, labour & T&P etc. complete. But Excluding cost of GST.

Providing and laying Glazed Vitrified tiles Matt/Antiskid finish in floor of size 600 x 600 mm 10-12 mm thickness with water absorption less than 0.08% and conforming to IS:15622, of Kajaria/Somany/Johnson brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. But Excluding cost of GST.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).Brand(Make Sail & Tata). But Excluding cost of GST.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. But Excluding cost of GST.

Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete. 110 mm But Excluding cost of GST.

10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat:With common burnt clay F.P.S.(non modular) brick tile of class designation 10. But Excluding cost of GST.

12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand). But Excluding cost of GST.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. But Excluding cost of GST.

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. @ 1 KG per bag of 50 kg Cement Bag. But Excluding cost of GST.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre. But Excluding cost of GST.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. But Excluding cost of GST.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm. But Excluding cost of GST.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of Asian/Berger/Birla opus brand & manufacturer of required shade and colour all complete to achieve even shade and colour :New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre. But Excluding cost of GST.

Painting with synthetic enamel paint of Asian/Berger/Birla opus brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. But Excluding cost of GST.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby red (Area of slab over 0.50 sqm). But Excluding cost of GST.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. But Excluding cost of GST.

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete. But Excluding cost of GST.

Providing and Fixing 25 mm dia brass curtain rods of wall thickness 1.25 mm with two brass brakets fixed with brass screws and wooden plugs etc.wherever necessary complete. But Excluding cost of GST.

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. But Excluding Cost of GST

Providing and injecting chemical enulsion for preconstructional antitermite treatment and creating a chemical barrier under and around the columns pits wall trench basement exacavation top surface of plinth filling junction of wall and floor alon the external per meter of building expansion joints sorounding of pipes and conduit etc. complete (plinth area of the building at ground floor only shall be measured as per i.s 6313(part 1981) .aldrine emulsificable concentrate of any other apporoved matreial such as hepthchlor or chlordance will be used . the rate of application of chemical emulsion shall be as follows .1 treatment for masonry and foundation 5 litres per sqm 2.back fill in immidiate contact with foundation 7.5 ltrs/sqm3.treatment of top surface of plinth filling 5 litres per sqm 4 treatment junction of soil along external per meter building 7.5ltres/sqm5.treatment of soil under apron along external perimeter 5 litre/sqm. But Excluding Cost of GST

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter. But Excluding Cost of GST

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend 87.5' But Excluding Cost of GST

Shoe (Plain). 110 mm Shoe But Excluding Cost of GST

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: But Excluding Cost of GST

Providing and fixing white vitreous china extended wall mounting water closet of size 780 * 370 * 690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. But Excluding Cost of GST

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Single half stall urinal with 5 litre P.V.C. automatic flushing cistern. But Excluding Cost of GST

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps. But Excluding Cost of GST

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board (510x1040 mm bowl depth 200 mm). But Excluding Cost of GST

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. But Excluding Cost of GST

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 40 mm dia. But Excluding Cost of GST

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. But Excluding Cost of GST

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm. complete, including cost of cutting and making good the walls and floors:100 mm inlet and 75 mm outlet Sand cast iron S&S as per IS - 3989. But Excluding Cost of GST

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. But Excluding Cost of GST

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. But Excluding Cost of GST

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal dia Pipes. But Excluding Cost of GST

Same as Item No. 66 but 20 mm nominal dia Pipes. But Excluding Cost of GST

Same as Item No. 66 but 25 mm nominal dia Pipes. But Excluding Cost of GST

Same as Item No. 66 but 32 mm nominal dia Pipes. But Excluding Cost of GST

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standard and weighing not less than 810gms. 15mm dia, nominal bore. But Excluding Cost of GST

Providing and Fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore.15 mm nominal bore. But Excluding Cost of GST

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore But Excluding Cost of GST

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore But Excluding Cost of GST

Same as Item No. 73 but 32 mm nominal bore. But Excluding Cost of GST

Providing and Fixing C.P. Brass Angle Valve for Basin Mixer and Geyser points of approved quality conforming to IS:8931,15mm nominal bore. But Excluding Cost of GST

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. But Excluding Cost of GST

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :150 mm diameter. But Excluding Cost of GST

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m :Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia. But Excluding Cost of GST

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. But Excluding Cost of GST

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.150 mm dia. But Excluding Cost of GST

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin-charge. But Excluding Cost of GST

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5. But Excluding Cost of GST

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in reinforced cement concrete slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : But Excluding Cost of GST

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5. But Excluding Cost of GST

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. But Excluding Cost of GST

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. But Excluding Cost of GST

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required. 4 Module (125mmx75mm) But Excluding Cost of GST

Same as Item No. 87 but with 6 Module (200mmx75mm). But Excluding Cost of GST

Same as Item No. 87 but with 8 Module (125mmx125mm). But Excluding Cost of GST

Same as Item No. 87 but with 12 Module (200mmx150mm). But Excluding Cost of GST

Wiring for circuit submain wiring alongwith earth wire with the following size of FRLS PVC insullated copper conductor, single core cable in surface recessed medium class PVC conduct as required . 2x2.5 sqmm + 1x2.5 sqmm earth wire. But Excluding Cost of GST

Same as in item 91 but with 2x6.0 sqmm + 1x6.0 sqmm earth wire. But Excluding Cost of GST

Supplying and fixing 5A to 32 A rating , 240/415 V , 10ka , "C" curve , miniture circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections , testing and commissioning etc. as required. Single pole. But Excluding Cost of GST

Supplying and fixing of following ways ,single pole and neutral ,sheet steel MCB distribution board 240 V on single/recess complete with tinned copper bus bar neutral bus bar earth bar din bar interconnections powder painted earthing etc as required.(But without MCB/RCCB/Isolator).6 way Double Door. But Excluding Cost of GST

Making of Earthing with COPPER EARTH PLATE of size 600mmx600mmx3mm thick i/c accessories and providing masonary enclosure with heavy duty Cover plate having Locking arrangement and watering pipe of 2.7 meters etc. with SALT & CHARCOAL as required. But Excluding Cost of GST

Supply and Fixing of one number 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode including connection/termination with GI thimble etc.as required. But Excluding Cost of GST

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. But Excluding Cost of GST

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. But Excluding Cost of GST

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. But Excluding Cost of GST

Supplying , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealedcopper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180-260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 0C. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electrotechnical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as perCPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient temperature).Inverter Type - Cooling only 1.5 TR with 5 Star BEE Rating. But Excluding Cost of GST

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. But Excluding Cost of GST

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)12 way (4 + 36), Double door. But Excluding Cost of GST

Providing and fixing following rating and breaking capacity and pole MCB/MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.200 Amp, 36KA, FPMCCB. But Excluding Cost of GST

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. But Excluding Cost of GST

Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. A.( 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire.) But Excluding Cost of GST

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. But Excluding Cost of GST

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing up to two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required. But Excluding Cost of GST

Installation ,Testing, Commissioning of pre-wired,flourescent, compact flourescent, LED fittings of all types complete with accessories and tube/lamp etc, directly on ceiling/wall, including connections with 1.5 sqmm FRLS PVC Insulated, copper conductor single core cable and earthing the same etc.as required. But Excluding Cost of GST

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (up to 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. But Excluding Cost of GST

Installation, testing and commissioning of exhaust fan,in the existing opening, including making good the damage, connections etc as required.A)450 mm. But Excluding Cost of GST

Extra for fixing the Louvers/shutters complete with frame for a exhaust fan of all sizes. But Excluding Cost of GST

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required.A)For 4 way, Double door TPN MCBDB. But Excluding Cost of GST

Laying of 1 No. PVC insulated and PVC sheathed/XLPE power cable of 1.1KV grade of following size direct in ground including excavation,sand cushioning,protective covering and refilling the trench etc. as required.A)Upto 35 sqmm. But Excluding Cost of GST

LED Smart Street light fixture 120 watt, powder coated pressure die cast aluminium (System lumen efficacy >135 lm/Watt) as details in items.. But Excluding Cost of GST

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.). But Excluding Cost of GST

Providing and fixing 35 mm thick panelled or panelled and glazed shutters of second class teak wood for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. But Excluding Cost of GST

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. (80x1.25 mm M.S. laths with 1.25 mm thick top cover). But Excluding Cost of GST

U-PVC pipes (working pressure 4 kg / cm²) Single socketed pipe 75 mm dia. But Excluding Cost of GST

uPVC single equal Tee (with door) 75x75x75 mm. But Excluding Cost of GST

uPVC single equal Tee (with door) 110x110x110 mm. But excluding Cost of GST.

Please Enable Macros to View BoQ information