Construction of Guest House on the 1st floor of Eye Mobile Unit in Zonal Hospital Dharamshala, Distt. Kangra (H.P.)

Amount

Excavation in drains and channels etc; in earth work in all kind of soil, such as pick work, jumper work, pick jumper work, blasting work, hard and soft blasting, saturated soil including chiseleing or any other mixed variety of soil, lift upto any heights, stacking the excavated soil for all heights from the edge of excavation and then returning the stacked soil in 15cm (Fifteen centimetre) layer when required into plinths sides of foundations etc. Consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as directed by the Engineer- Incharge, within all leads, lifts of materials and other incidentals. As per approved drawing, design and as directed by the Engineer-in-Charge.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts Square, rectangular or polygonal in plan within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings as per Architectural drawing and the like within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers girders and lintels sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depths within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls under any thickness within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landings, shelves their supports balconies, beams, girder, bressumers and cantilevers in all depth / thickness upto all floor level etc; within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in columns, pillars posts and struts for all floors heights in all depth / thickness within all leads, lifts of materials and other. incidentals. as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete in reinforcement work for reinforced concrete Chhajjas for all thickness in all floor levels up to all heights and all thickness including finishing the exposed surface with cement mortar 1:3 (One cement : Three sand) to give a smooth and even surface including centering/ form work and curing complete but excluding the cost of reinforcement for reinforced concrete work up to all floors level up to all height as per direction of Engineer-In-charge. within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying reinforcement concrete work M-20 (M-twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) cement contents not less than 320 kg (Three hundred twenty kilogram) mechanically mixed and vibrated to give smooth and even surfaces including centring and shuttering etc. but excluding the cost of reinforcement as in mouldings as in cornices, windows sills etc not exceeding 15cm (Fifteen centimetres) in girth as per approved specification, drawing and design complete upto floor all level within all leads, lifts of materials and other. incidentals and as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing Tor steel reinforcement of Sail / Tisco /Tata for reinforced cement concrete work including bending, binding, straighting, cutting and placing in position complete including cost of binding wires complete for all floors within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Second class brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:6 (One cement isto Six sand) and curing complete,within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Second class half brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:4 (one cement :four sand) within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing anodised aluminium work of Hindalko, Jindal for door, window, ventilators and partitions aluminium frame extrusion sections (No 14081) 127X44.45X3.00mm (one hundred twenty seven into forty four deciman four five into three millimetre) of Jindal / Hindalco aluminium extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/ panelling C.P. brass/stainless steel screws. All complete as per architectural drawings and the directions of Engineer-In-Charge for door, window and ventilator and glazed portion frames within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing coloured anodised aluminium work of Hindalko, Jindal for door, window, ventilators and partitions with extruded built up standard tubular and other sections as required of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips,or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle,aluminium, snap beading for glazinge/panelling C.P. brass/ stainless steel screws. All complete as per architectural drawings and the directions of Engineer-In-Charge. For shutters of doors window and ventilator including providing and fixing hinges / pivots and making provisions for fixing of fittings wherever required including cost of PVC / neoprene gaskets as required (fittings and glazing/panelling shall be paid for separately) within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing hard drawn steel wire fabric 75x25 mm (Seventy five into twenty five milimetres) mesh of weight not les than 7.75 kg per sq.m to window frames etc. including 60x20 mm (Sixty into Twenty milimeter) beading of 2nd class indian teak wood.within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing aluminium 8mm (eight millimetre) thick grill anodised powder coated pattern to existing window /ventilatior with 80mmx80mm (eighty millimetre into eighty millimetre) panels holes with 25x8mm (twenty five into eight millimetre) thick aluminium flat in windows and ventilators including fixing with aluminium screws or bolts and nuts complete in alluminium channels base frames (Aluminium channels base frames to be measured and paid for separately) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing angle iron frames manufactured from M.S.Angle iron section 25X25X5mm (Twenty five into Twenty five into Five milimetres) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25mm (Twenty five into Twenty five milimetres) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5mm (Two decimal Five milimetres) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in-Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

channels section 75x40x6mm (seventy five into forty into six millimetre) M.S. flat 75x4mm (seventy five into four millimetre) combination as per design drawing i/c hinges, jambs, beeds if required threshold of M.S. angles 50x25mm (fifty into twenty five millimetre) welded or rigidly fixed by mechanical means lugs, with split ends tails to each jambs including steel butts hinges 2.5mm (two decimal five millimetre) thick with a provision of locking arrangements shock observes and specified and applying coat of approved steel primer after pre-treatment of surfaces as directed by the Engineer–in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and Fixing 12 mm (twelve millimetre) thick both side prelaminated water proof particle board of Action Tesa / Centuary / Kitlam / Kitply /Greenlam / Merinolam as per ISI and approved shade within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing to existing door frames, 30mm (Thirty millimetres) thick factory made PVC panelled door shutter consisting of frame made out of M.S. tubes of 19 (Nineteen) gauge thickness and size of 19mm x19mm (Nineteen into nineteen millimetres) for styles and 15mmx15mm (Fifteen into fifteen millimetres) for top & bottom rails, code 9.120 of Rajshri M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm (Five millimetres) thick heat moulded PVC "C" channel of size 30mm (Thirty millimetres) thickness, 70mm (Seventy millimetres) width out of which 50mm (Fifty millimetres) shall be flat and 20mm (Twenty millimetres) shall be tappred in 45 (Forty five ) degree angle on either side forming style and 5mm (Five millimetres) thick, 95mm (Ninety five millimetres) wide, PVC sheet out of which 75mm (Seventy five millimetres) shall be flat and 20mm (Twenty millimetres) shall be tapered in 45 (Forty five) degree on the inner side to form top and bottom rail and 115mm (One hundred fifteen) wide PVC sheet out of which 75mm (Seventy five millimetres) shall be flat and 20mm (Twenty millimetres) shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm (Ten millimetres) thick, 20mm (Twenty millimetres) wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails, joints mitred and jointed with solvent cement adhesive i/c fixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm ( One hundred into fifty into one decimal ninety millimetres) size with necessary screws etc complete as directed by the Engineer-in-Charge.within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixig glazing with glass panes of 5mm (five milimertres) thickness of modi guard / Sant gobain (weight not less than 10.00 kg/sqm (ten decimal zero kilograme per square metres) glazing in aluminium door, windows, ventilators\ shutter and partition etcetra; with PVC/Neoprens gasket etcetra; complete as per the architectural drawings and the direction of Engineer-in-Charge (Cost of aluminium snap beading shall be paid separately) within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Supplying and fixing 4 mm (four millimetre) thick frosted glass panes of modi guard / Sant gobain including fittings and putty complete in all respect within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Complete box of cupboard of 25mm (Twenty five millimetres) thick water proof termite resistant commercial board Uniply / Green ply /Kit ply /Dura ply / Marino (ISI Marked ) for shutter including 19mm thick shutter. Back side of cupboard shall be 6 to 12 mm (six to eight millimetre) thick water proof ply. The shutter from all side shall also have 6mm (six millimeter) thick hard board edging/ Topping to be finished with 1mm (one millimeter) thick mica lamination of Century / Greenlam / Action Tesa / Merinolam approved shade of office including fixing handles be provided in wood colour with nickel plated piano hinges with screws etcetera within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 25mm (twenty five millimetre) thick Commercial Board of Centuary ply (ISI marked) water proof shutters for SDB with 6 mm (six millimetre) thick hard wood edging all round and PGI sheet lining in side including fixing with nickel plated piano hinges with screws etc complete) within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 19mm (nineteen millimetre) thick Commercial Board water proof board of Uniply/ Greenply /kitply/Centuary ply / Duraply /Marino ( ISI Marked ) Shelves and shutters with hard wood edging to be finished with 1mm (one millimetre) thick lamination of centuary/ Greenlam/ Action Tesa / Merinolam and approved shade including fixing with nickel plated piano hinges and screws etc complete) within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing wood work in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position.2nd class kiln seasoned Deodar wood within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing magnetic catcher for cup board shutters with necessary screws etcetra; within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 65x35mm (Sixty five into Thirty five millimetres) special quality bright finished brass cup-board locks or ward robe locks with six levers including necessary screws etcetra complete (Indian make of approved quality) within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 300x16mm (Three hundred into Sixteen milimetres) size Pilot/sheel anodized aluminium sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etc. within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing aluminium Pilot/sheel anodized transparent or dyed to required colour and shade with necessary screws etc.Tower bolts (Barrel type) as approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

200x10mm (Two hundred into Ten milimetres) size

150x10mm (One hundred fifty into Ten milimetres) size

Providing and fixing aluminium Pilot/sheel or equivalent anodized transparent or dyed to required colour and shade and of approved make with necessary screws etc. handles with the necessary screws etc. complete. within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

125mm (One hundred twenty five milimetres) size

100mm (One hundred milimetres) size

Providing and fixing aluminium oxidized Pilot/sheel 250mm (two hundred fifty milimetres) size hook and eyes of complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing Aluminum oxidized Hydraulical door closer Complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 100mm (one hundred millimetres) bright finished brass door stoper with rubber cushion screws etc to suit shutter thickness complete within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing 25mm (Twenty five milimetres) thick Kota Stone flooring 55x55cm (Fifty five into Fifty five centimetres) (Mirror polished) with 7.5 cm (Seven decimal Five centimetres) wide Jaislmer yellow (uniform colour) marble band base of 20mm (twenty millimeter) thick cement mortar 1:4 (One cement: Four sand) laid over and jointed with Grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing moulding and nosing complete within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge . The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying 19 mm (nineteen millimetre) thick Marble work with round nosing Veneer work 2.50cm (two decimal fifty centimetre) thick in cement mortar 1:3 (one cement isto three sand) including pointing with white cement marble dust 1:2 (one white cement isto two marble dust) with an admixture of pigment to match the marble shade within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 10mm (ten milimetre) thick full body matt finish vetrified tiles of Nitco / Simpolo / Orient -Bell / Rak/ Kajaria / AGL/Johnson / Somany as per approved shade and design 600x600mmx10mm of size (six hundred millimetre into six hundred millimetre into ten milimetre) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying Double charged vetrified tiles of Nitco / Kajaria / AGL /Johnson / Simpolo Orient -Bell / Somany 600x 600mm x 10mm (six hundred millimetre into six hundred millimetre into ten millimetre) in grey/coloured or of approved shade and design in flooring, treads of steps and landing laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

50mm (fifty milimetres) thick cement concrete flooring 1:2:4 (One cement isto Two sand isto Four graded crushed stone aggregate 20mm (Twenty milimetres) nominal size and down gauge) laid in one layer finished with a floating coat of neat cement within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying spartic ceremic tiles of premium quality of Nitco / AGL/ Kajaria / Somany / Bell first quiality approved shade 5.5 mm (Five decimal five millimetres) thick in flooring 300x300mm (Three hundred into Three hundred millimetres) size in treads of steps laid on a bed of 12mm (Twelve millimetres) thick cement mortar 1:3 (One cement isto Three sand) finished with flush pointing in white cement upto all floor level, as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana and all type of taxes imposed by the Government.

Providing and fixing 10mm (ten milimetre) thick full body matt finish vetrified tiles of Nitco / Simpolo / Orient -Bell / Rak/ Kajaria / AGL/Johnson / Somany as per approved shade and design 300x300mmx8mm of size (three hundred millimetre into three hundred millimetre into eight milimetre) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying Duro stone vitrified tiles 300x300mm x 8mm (Three hundred into three hundred into eight milimetres) in grey/colour of required shade in skirting, risers of steps and dados laid over 12mm thick cement mortar I :3( 1 cement :3sand) with cement slurry mixed with pigment to the the shade of tiles as required, complete within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying 300X450 mm (three hundred into four hundred fifty millimetre) Ceremic Glazed tile of Kajaria/ Swastik / Somany / Bell / AGL/Johnson with one border matching contrast at top in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete within all leads, lifts of materials and other incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

8mm (eight millimetre) thick First class indian teak ply wooden paneling uptp 135mm(one hundred thirty five) height over 50 x 31 mm (fifty into thirty one millimetre) soft wood grid frame work at 600 mm (six hundred millimetre) centre to centre with decorative teak wood beading over teak ply of size 25 X 12 mm (twenty five into twelve millimetre) having moulding on both side cornice / Edging on the top of paneling to be finished with 55 x 30 mm (fifty five into thirty millimetre) teak wood beading as per detail. planking tongued and grooved within all leads, lifts of materials and other incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing 25mm (Twenty five milimetres) thick step tile of reslite / Nitco / Jonson / Kajaria as per approved shade for slab with round nosing over heads of steps and landings on a bed of 12mm (Twelve milimetres) (Average) thickness cement mortar 1:3 (One cement isto Three sand) and jointed with Grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing, nosing and moulding complete within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and Laying 25mm (Twenty five milimetres) thick reslite / Nitco / Jonson / Kajaria as per approved shade in risers of steps and pillars laid on a bed of 12mm (Twelve milimetres) (Average) thickness cement mortar 1:3 (One cement : Three sand) and jointed with Grey cement slurry mixed with pgiment to match the shade of the slabs including rubbing and polishing, nosing, moulding complete in all respect within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 0.60mm (Zero decimal Six Zero milimetres) thick prepainted steel sheet ISI marked - Z 120 of tata Durashine/ sail / reliance / jindal in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (Five) microns primer fixing with prepainted iron J or L hooks,bolts and nuts with prepainted limpet and rubber washers complete with all accessories as required within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing ridges or hips 60 cm (Sixty centimetres) over all with 0.60mm (Zero decimal Sixty milimetres) thick Tata Dura shine prepainted steel sheet ISI marked - Z 120 of approved make in ridges of sail / relience / Jindal Sakti with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating of back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing valleys 90 cm (ninety centimetres) over all over all with 0.60mm (Zero decimal Six zero milimetres) thick prepainted sheet ISI marked - Z 120 of sail / TATA / relience / Jindal roofing with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (five) micron primer coating, back coat of polyster of 5 (Five) microns including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 30cm (thirty centimeters) wide 25cm (twenty five centimeters) deep as per design and drawing 0.60mm (Zero decimal Six zero milimetres) thick plain G.I. sheet TATA Shakti for gutter with iron brackets 40x3mm (Forty into Three milimetres) size bolts and nuts and washers etcetera including making necessary connections with rain water pipe and providing complete accesories within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing plain M.S. B.P. sheet TATA/SAIL/JINDAL 2.00 mm (Two decimal zero millimeter) thick fixed in eaves board / facia / soffits /ceiling including cutting, fixing and welding to steel rafter, member and applying a coat of red lead primer with gas/ electric welding in position complete (frame work is to be measured and paid for separately) within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing on wall face 150mm (One hundred fifty milimetres) diametres P.V.C. rain water pipes of working pressure 4/6kg (four / six kilogramme) per square centimetre of finolex / Relience / vectus/ prince pipe for rain water pipe fixed with approved adhesive including filling the joints complete within all leads, lifts of materials and other incidentals, and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing on wall face P.V.C. acessories for rain water pipes of working pressure 4/6kg (four / six kilogramme) per square centimetre of finolex / relience / vectus ./ Prince or its equivalent for rain water pipe fixed with approved adhesive including filling the joints complete in all requirement within all leads, lifts of materials and other incidentals. and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

150mm (One hundred fifty milimtres) diametrees PVC Plain bend

150mm (One hundred fifty milimtres) diametrees PVC shoe

Providing and fixing PVC holder bat clamps of approved design to P.V.C.. rain water pipe embedded in and including cement concrete blocks 10x10x20cm of 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty milimetres) nominal size and cost of cutting holes and making good the walls etc; within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

100mm (One hundred milimetres) diameter.

Steel work welded in built up sections of TATA/SAIL joists channels, angles, tees with connection plates or angles, cleat as in trusses, trussed purlins main and cross beams, hips jack rafters, purlins connected to common rafters and the like in building including cutting, fixing, lifting, hoisting and; placing in position complete and applying a coat of red lead paint within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint In beams joists channels, angle tee flat with connecting plates or angles cleate in beams or cross beams, hip or jack rafters, purlins connecting ,common rafter and in gratings framed guard bars, ladders, railling, brackets and similar works within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 50 mm (fifty millimetre) dia SST (Stainless steel) pipe handrail fixed with 35 mm (thirty five millimetre) dia stainless steel baluster as per detail in combination of 35mm (thirty five millimetre) dia and 15/20mm (fifteen / twenty millimetre) SST pipe baluster knock down railing of KICH hand rail fixed on 10X50mm (ten into fifty millimetre) S.S.flat baluster placed at 1200 mm (one thousand two hundred millimetre) C/C along with 3 (three) nos (three Number) @ 16 MM (sixteen milimetre) mid rail connected at the side of the baluster with fixtures .The baluster would be fixed on the floor with casted base plate minimum 6mm thick base plate shall be concealed with suitable S.S. 316 grade cover cap .railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) within all leads, lifts of materials and other. Incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing railing 50mm (fifty milimetre) dia M.S. hollow pipe staircse railing welded with 25mm (twenty five milimetre) bluster dia embedded in cement concrete bed, 30 cm C/C with a clear height of 85cm (Eighty five centimetre) and jointing with electric/gas welding at top alongwith hand rail of 75x65mm (seventy five into sixty five millimetre) vertical ballusters welded jointed with each other with 2 (Two) Nos M.S. flat of 50x5mm (fifty into five millimetre) complete with applying coat of red lead paint as per specification and direction of Egniener-Incharge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Painting two or more coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing of Asian paint/ Nerolac/Berger of approved shade to give an even shade including cleaning the surfaces of all dirt, dust andother foreign matter enamel paint other than white within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting with ready mixed paint brushing wood primer pink within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Painting two or more coats of Nerolac/Asian paint/ Berger (excluding priming coat) on new wood and wood based surface with enamel paint other than white to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering and stoping within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

6mm (Six milimetres) thick cement plaster in ceiling with cement mortar 1:3 (One cement: Three sand) for all heights within all leads, lifts of materials and other incidentals as per approved approved specification, drawings and design. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plaster in single coat on fair side of brick/concrete/ stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Applying Birla / J.K white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Finishing wall with Apex weather proof exterior grade emulsion of Asians Paints /Nerolac suraksha /Bergur paint Exterior Emulsion as per approved shade approved design (Apexultima) on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Applying two coatc of Acrylic Washable emulsion Asian / Berger / Dulux /Nerolac paints for interior painting of approved shade with brushes plain smooth finish composed of acrylic polymere in emulsion inorganic/special pigment siliceous aggregate anti fungicides anti-rusting & foaming in two coat i/c necessary putty to give smooth even surface, sand papered smooth complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Distempering (two coats) with synthetic & acrylic oil bound washable distemper with Nerolac/ Asian paints of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth.Priming coat with distemper primer within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing precast cement concrete jali 1:2:4(one cement: two sand : four graded stone) 6mm (Six milimeter) nominal size reinforced with 1:6mm (One point six milimetres) dia mild steel wire including cetering and shuttering, rougherning cleaning, fixing and finishing in cement mortar 1:3(one cement :3 sand) etc, excluding plastering of the jambs sill and soft within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing polythelene aluminum polythelene (PE- AL-PE) composite pressure pipe U.V. stabilized with carbon block confirming to I.S. 15450-2004 of Kitec for water supply including clamps at appropriate spacing, cutting fixing and making good the walls etcetera; but excluding the cost of fittings (Internal work), including filling the joints with approved adhesive complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

1216 (16mm) sixteen millimeter diameter pipe O.D. pipe

1620 (20mm) twenty millimeter diameter pipe O.D. pipe

Making connection of galvanized mild steel distribution branch with galvanized mild steel main 20mm to 40nmm (Twenty milimetres to Forty milimetres)nominal bore by providing and fixing tees including cutting and threading the pipe complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes light grade ISI marked of fenolex/vectus/price 4.6mm thick having pressure not less than 6kg /cm2 (six kilogramm per centimetre square) including fixing with approved adhesive etc. complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

150mm (One hundred fifty milimetres) diametres

110mm (One hundred ten milimetres) diametres

75mm (One hundred ten milimetres) diametres

Providing and fixing M.S. holder bat clamps of approved design to P.V.C.. rain water pipe embedded in and including cement concrete blocks 10x10x20cm of 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty milimetres) nominal size and cost of cutting holes and making good the walls etc; within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

150mm (One hundred fifty milimetres) diameter.

100mm (One hundred ten milimetres) diametres

75mm (One hundred ten milimetres) diametres

Providing and fixing P.V.C. I.S.I. marked heal rest of Finolex / Vectus / Prince including filling the joints with including fixing with approved adhesive within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

150mm nominal (One hundred fifty milimetres) diameter. (confirming to BIS-14735-99)

110mm (One hundred ten milimetres) diameters (confirming to BIS-14735-99)

Providing and fixing P.V.C. Collar ISI marked of Finolex / Vectus / Prince including fixing with approved adhesive complete, within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

150mm (One hundred fifty milimetres) diameter. (confirming to BIS-14735-99)

110mm (One hundred ten milimetres) diametres (confirming to BIS-14735-99)

75mm (Seventy five milimetres) diametres (confirming to BIS-14735-99)

Providing and fixing P.V.C. I.S.I. marked cowl (confirming to BIS-14735-99) ISI marked of Finolex / Victus / Prince including fixing with approved adhesive complete, within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

75mm (Seventy five milimetres) diametres (confirming to BIS-14735-99)

Providing and fixing 110 x 90mm (One hundred ten into Ninety milimetres) P.V.C. I.S.I. marked floor trap of Finolex / Vectus / Prince ISI marked (confirming to BIS-14735-99) of self cleaning design including with approved adhesive cost of cutting and making good walls and floors complete, within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing vitreous China wash down, water closet squatting pan (Indian type W.C pan) Orissa Pattern No 20090 size 53 X 41 cm (fifty three into forty one centimetre) of Hindware /Cera /Jaquar of star white / snow white shade (Earth work, bed concrete,foot rest and trap to be measured and paid for separately) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing W.C. Of Star S no 20087 (S- 10) of size 57 X 35 X 39 Cm (Fifty seven into thirty five into thirty nine centimetre) of Hindware /Cera/ Jaquar of star white / snow white shade vitreous china wash down closet (European type W.C. pan) with internal P or S trap including jointing the trap with soil pipe in cement mortar 1:1 (one cement isto one sand) (seat cover and jet spray to be measured and paid for separately) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing PVC coloured/white with (dual flushing system) 10.00 Ltrs (Ten litres) capacity low level flushing cistern (Sleek Plus) Hindware/cera/Jaquar of star white / snow white shade with fittings such as lead valve less siphon, 15mm (Fifteen milimetres) nominal size PVC ball valve with polythene float, with flush buffor, unions and couplings for connection with inlet, outlet and over flow pipe, 40mm (Forty milimetres) diametres C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (over flow pipe to be measured and paid for separately) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing sand cast iron 100mm (one hundred millimetre) size P or S traps for water closet (squatting pan) including jointing the trap with pan and soil pipe in cement mortar 1:1 (one cement isto one sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing G.I. inlet connection pipe for each flush pipe with W.C. pan within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing plastic seat solid type and cover of Hindware/cera/Jaquar of star white / snow white shade for wash down water closet with C.P. brass hinges and rubber buffers (white plastic seat and cover) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing vitreous china urinal large flat back No of 60002 of size 390 x 375x590mm (three hundred ninety into three hundred seventy five into five hundred ninety milimetres) size Hindware / Jaquar of star white / snow white shade connection with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately) within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 600x300mm (Six hundred into Three hundred milimetres) vitreous china division plate for urinals of Hindware /cera/Jaquar of star white / snow white shade i/c necessary fittings in all respect within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing vitreous china wash basin Delta No.10010 of Cera / Hindware 55x40 CM (fifty five into forty centimetre) with single hole for pillar tap with pedestal including C.I. or M.S. brackets, painted white including cutting holes and making good the same but excluding fittingswithin all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing vitreous china wash basin Garnet No.10080 of Cera / Hindware 58x43cm (fifty eight into forty three centimetre) (under counter basin) Hindware / cera / Jaquar of star white / snow white shade with single hole for pillar tap with pedestal including C.I. or M.S. brackets, painted white including cutting holes and making good the same but excluding fittings within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing stainless steel kitchen sink size 610 x510 mm (six hundred ten into five hundred ten millimetre) with bowl depth 200 mm (two hundred millimetre) of AMC unik / diamond approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted including cutting holes and making good the same but excluding fitting within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) nominal size diametres rubber plug for wash basin within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) diametres M.I. union for wash basin or sink.complete within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 32mm (Thirty two millimetres) diametres C.P brass waste for wash basin and sink of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal waste for wash basin or sink complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 100mm (One hundred millimetres) diametres C.P. Grating Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal for gully floor or Nahni trap within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing flat back 600x450mm (Six hundred into Four hundred fifty milimetres) bevelled edge mirror of modiguard / actual mounted on 6mm (Six milimetres) thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washers within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 600x20mm (Six hundred into Twenty milimetres) C.P. brass Towel rail of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal.brackets fixed to wooden plugs within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 600x120mm (six hundred into one hundred twenty millimetre) glass shelf of Modi guard / flout saint / sant gobind / Aashai (Heavy duty makes ISI marked) brackets and guard rail complete fixed to plugs with C.P. brass screws within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing C.P. brass toilet paper holder of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of jal as per direction of Engineer-in-Charge, within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing C.P. jet spray of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal of approved quality and colour with one metre tube within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) diametre nominal bore chromium plated ISI marked fancy bib tap of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of jal complete in all respect with necessary fittings with in all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) diametre C.P. stop cocks of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetres) diametres C.P. brass pillar tap with capstan Head of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetres) diametres C.P.brass angle valve without nuts of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal as per approved drawing and design directed by the Engineer-in-Charge within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetres) nominal bore C.P. brass full way valve with wheel, of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetres) nominal bore C.P. brass valve (Horizontal plunger) type High pressure with polythene plastic floats of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing PVC connection pipe with brass unions ISI marked 45cm (forty five centimeters) long and 15mm (fifteen millimeters) nominal bore complete. within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing PVC waste pipe for wash basin, sink including check nut within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge.

Providing and placing water tank make P.V.C. SINTEX three layer having capacity of 1000 (One thousand) liters each tank with necessary fittings including over flow pipe scour pipe etcetera and pads required for in let and out let ball valve with cover and locking arrangements complete in all respect within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying 150mm (one hundred fifty millimetre) (to level or slopes) and jointing with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 sand) salt glazed stoneware pipes grade 'A' of the following internal diameters including testing of pipes and joints complete: within all leads, lifts of materials and other incidentals, as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge.

Providing and laying 150mm (one hundred fifty millimetre) cement concrete 1:5:10 (one Cement isto five Sand isto ten graded stone aggregate 40mm (forty millimetre) nominal size bedding for PVC pipes of the following internal diameters, necessary form work and curing complete within all leads, lifts of materials and other incidentals, as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge.

Construction manhole with R.C.C. top slab in 1:2:4 (One cement isto Two sand isto Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) foundation concrete 1:4:8 (One cement isto Four sand isto Eight graded crushed/broken stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm (Fifteen milimetres) thick with cement mortar 1:3 (One Cement isto three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement isto Two sand isto Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetres) 500mm(Five hundred milimetres) deep, including C.I. cover with frame (light duty single seal pattern -I) 450x610mm (Four hundred fifty into six hundred and ten milimetres) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilograms) weight of cover 23Kgs (Twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 300mm (Three hundred milimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Construction manhole with R.C.C. top slab in 1:2:4 (One cement isto Two sand isto Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) foundation concrete 1:4:8 (One cement isto Four sand isto Eight graded crushed/broken stone aggregate 40mm (Forty milimetres nominal size) inside plastering 15mm ( Fifteen milimetres) thick with cement mortar 1:3 ( One Cement isto three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement: Two sand isto Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetres) 1.00 mtrs(One metre) deep, including C.I. cover with frame (light duty single seal pattern -I) 455x610mm (Four hundred fifty five into six hundred and ten milimetres) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilograms) weight of cover 23Kgs(twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 300mm (Three hundred milimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) within all leads, lifts of materials and other incidentals.

Constructing brick masonry chamber for under ground C.I. inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5(One cement: Five sand) C.I. cover with frame(light duty) 455x610mm(Four hundred fifty five into Six hundred ten milimetres)internal dimensions total weight cover and frame to be not less than 38Kgs (Thirty eight Kilograms) weight of cover 23 Kgs (twenty three kilograms)and weight of frame 15 Kgs (Fifteen kilograms) RCC top slab with 1:2:4 (One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty milimetres nominal size) foundation concrete 1:5:10 (One cement: Fiver sand: Ten graded crushed/broken stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm ( Fifteen milimetres) thick with cement mortar 1:3 ( One Cement: three sand) finished with a floating coat of neat cement on walls and bed concrete etc. complete inside dimensions 455x610mmx450mm (Four hundred fifty five into Six hundred ten into Four hundred fifty milimetres) deep within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing polythelene aluminum polythelene (PE- AL-PE) composit end seal compression fitting as per IS-15450 of kitec for cold water supply e.g. tees, elbows, reduser,connceters,couplers and claps jointing testing and fitting complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Equal Tee (1620)

Female elbow(1620 X 15mm thread)

Female branch tee(1620x1620 x20 mm thread)

Female elbow(1620 X 15mm thread)

Male thread connecter (1620 X15mm thread)

Kapil Sharma

Harbhajan singh