Construction of office bldg. of Industries and Commerce Department. Haryana in Plot No. 01 and 02, Sec-1, MDC Panchkula (Pdg. E.I, Sub Station, Rising Main and DG Set Only).

Amount

[20.71.1]Supply, erection, testing of Ceiling fans IS marked (as per IS code 374) with suitable GI pipe complete in all respects complete as per directions of Engineer-in-charge 1. 48" (1200mm) [Through Rate]

[20.72]Supplying, errection, testing of Exhaust fan (as per IS code 374) having a capacity of 45 cubic metre per minute complete with suitable G.I sheet ducting in structure confirming to latest IS specifications complete in all respect to satisfaction of Engineer-in-charge. [Through Rate]

[20.84]Providing and fixing of insulated rubber matting suitable for 11 KV installation 1 M x 2 M x 12 mm thick (IS code 15652-40091) as per specification complete and as per directions of Engineer-in-charge [Through Rate]

[20.86]Supply, erection, testing and commissioning of G.O. Switch two poles, with blade, pin 6 insulators operating handle with GI pipe 25 mm class B complete in all respects. [Through Rate]

[23.2.1.1]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 1.1. Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe. Group A [Through Rate]

[23.2.2.1]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 2.1. Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modular switch GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe. Group A [Through Rate]

[23.2.4.1]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 4.1. Wiring in MS conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required Group A [Through Rate]

[23.2.5.1]COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS) 5.1. Wiring in MS conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required Group A [Through Rate]

[23.20]Fixing of LED Tube light/ 2*2 ft square panel fitting directly on wall /ceiling or false ceiling including making connections etc as required [Through Rate]

[23.21]Fixing of LED Down lighter 7 to 28 Watt on ceiling or in false ceiling , including cutting/making hole in ceiling including making connections etc as required [Through Rate]

[23.22.1.11]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.11. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 200 to 250 amp, 25 KA [Through Rate]

[23.22.1.12]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.12. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 300 to 400 amp , 50 KA [Through Rate]

[23.22.1.9]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.9. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp , 25 KA [Through Rate]

[23.22.2.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 2.1. MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings MCCB up to 125 A FP [Through Rate]

[23.22.4.5]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.5. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 4 way ( 8 incoming and 3phase*4 outgoing) [Through Rate]

[23.22.4.7]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.7. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 8 way ( 8 incoming 3phase*8 outgoing) [Through Rate]

[23.22.5.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole [Through Rate]

[23.22.5.8]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.8. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. MCBs FOUR POLE [Through Rate]

[23.24.1]MS STAND, BUS BAR CHAMBER AND PANELS 1. Supply and erection of M.S. angle iron frame duly welded for housing M.S. sheet & main switches etc. on it, fixed on wall by means of suitable size of rag bolts with cement concrete, duly painted with three coats of approved paint including one coat of red oxide. [Through Rate]

[23.26.1]SAFETY ITEMS 1. Supply and erection of Medium Voltage caution notice plate of size 200*150 mm in three languages. [Through Rate]

[23.26.2]SAFETY ITEMS 2. Supply and erection of High Tension Voltage caution notice plate of size 250*200 mm in three languages. [Through Rate]

[23.26.3]SAFETY ITEMS 3. Supply and erection of shock restoration chart in glass frame. [Through Rate]

[23.26.4]SAFETY ITEMS 4. Supply & Erection of mild steel bucket stand suitable for 6 Nos. fire buckets,(but without bucket) including the cost of welding and painting of complete stand will one coat of red oxide and 2 coats of approved paint of red colour with all labour and material required to complete the job in all respect up to the entire Satisfaction engineer in charge of the work (size 6x4 made of GI pipe 32mm dia). [Through Rate]

[23.5.6.1]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.1. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm) [Through Rate]

[23.5.6.2]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.2. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 2.50 Sqmm(1.1.80mm) [Through Rate]

[23.5.6.3]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.3. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 4 Sqmm(1/2.24mm) [Through Rate]

[23.5.6.5]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.5. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 10 Sqmm(1/3.50 mm) [Through Rate]

[23.6.6.1]MS CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.1. Supply and erection of MS conduit pipe 1.6 mm thick , ISI marked surface/recessed in slab/wall/ceiling etc. including cost of MS bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. MS Pipe of 20 mm dia. [Through Rate]

[23.6.6.2]MS CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply and erection of MS conduit pipe 1.6 mm thick , ISI marked surface/recessed in slab/wall/ceiling etc. including cost of MS bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. MS pipe of 25 mm dia. [Through Rate]

[23.7.6.2]PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia. [Through Rate]

[23.8.10.1]FITTING AND ACCESSORIES 10.1. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 1 & 2 Modules including combined plate for Telephone and data [Through Rate]

[23.8.10.2]FITTING AND ACCESSORIES 10.2. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 3 Modules [Through Rate]

[23.8.10.4]FITTING AND ACCESSORIES 10.4. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 6 Modules [Through Rate]

[23.8.10.5]FITTING AND ACCESSORIES 10.5. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 8 Modules [Through Rate]

[23.8.10.6]FITTING AND ACCESSORIES 10.6. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 12 Modules [Through Rate]

[23.8.11.1]FITTING AND ACCESSORIES 11.1. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp 1 way switch [Through Rate]

[23.8.11.10]FITTING AND ACCESSORIES 11.10. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Blanking plate [Through Rate]

[23.8.11.2]FITTING AND ACCESSORIES 11.2. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp 2 way switch [Through Rate]

[23.8.11.3]FITTING AND ACCESSORIES 11.3. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 15 amp 1 way switch [Through Rate]

[23.8.11.4]FITTING AND ACCESSORIES 11.4. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp Socket [Through Rate]

[23.8.11.5]FITTING AND ACCESSORIES 11.5. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 15 amp 6 pin Socket [Through Rate]

[23.8.11.6]FITTING AND ACCESSORIES 11.6. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Bell Push [Through Rate]

[23.8.11.7]FITTING AND ACCESSORIES 11.7. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. step type Fan Regulator 2 modules 300 watt [Through Rate]

[24.1.10]EARTHING AND LIGHTENING ARRESTOR 10. Providing and fixing 25 mm x 5mm copper strip on surface or in recess for connections etc. as required with all labour and material. [Through Rate]

[24.1.3]EARTHING AND LIGHTENING ARRESTOR 3. Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. [Through Rate]

[24.1.4]EARTHING AND LIGHTENING ARRESTOR 4. Earthing with tinned copper earth plate 600mmx600mmx3mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) etc. complete as required. [Through Rate]

[24.1.5]EARTHING AND LIGHTENING ARRESTOR 5. Extra for charcoal or coke and salt for G.I. plate or copper plate earth electrode. [Through Rate]

[24.1.7]EARTHING AND LIGHTENING ARRESTOR 7. Supplying and laying 25mm x 3 mm G.I. strip in 40 mm dia,GI pipe as/from earth electrode including soldering etc. as required. [Through Rate]

[24.1.8]EARTHING AND LIGHTENING ARRESTOR 8. Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material. [Through Rate]

[24.1.9]EARTHING AND LIGHTENING ARRESTOR 9. Providing and fixing 25 mm x5 mm copper strip in 40 mm dia G.I. pipe from earth electrode as required. [Through Rate]

[24.10.1]CIVIL ITEMS (USED COMMONLY IN ELECTRICAL WORKS) 1. Digging & refilling of trench 30 cm wide below ground level for erection of pipe/cable (up depth of 1 Metre. underground cable excluding the cost of cable/pipe complete in all respect. [Through Rate]

[24.10.2]CIVIL ITEMS (USED COMMONLY IN ELECTRICAL WORKS) 2. Earth work in excavation in foundations, trenches etc. in all kind of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, staking the excavated soil clear from the edge of excavation and subsequent filling around masonry, in 15cm layers with compaction, including disposal of all surplus soil, as directed with in a lead of 30 metres. [Through Rate]

[24.10.4]CIVIL ITEMS (USED COMMONLY IN ELECTRICAL WORKS) 4. cement concrete 1:2:4 with stone aggregate 20 mm nominal size in Kerbs and the like items, finished smooth with 6 mm thick cement plaster 1:3 on exposed surface including from work, placing and fixing in position, complete at the ground level or in first storey [Through Rate]

[24.13.32]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 32. 25 Sq mm 4 core (Arm.) [Through Rate]

[24.13.38]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 38. 35 Sq mm 3.5 core (Arm.) [Through Rate]

[24.13.70]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 70. 120 Sq mm 3.5 core (Arm.) [Through Rate]

[24.13.88]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 88. 240 Sq mm 3.5 core (Arm.) [Through Rate]

[24.13.94]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 94. 300 Sq mm 3.5 core (Arm.) [Through Rate]

[24.16.4]HT CABLES (Aluminium Conductor, Armoured and Unarmoured) Providing and erection/ laying of XLPE (E) 11 KV HT Aluminium Conductor Armoured Cable ISI Mark Laid in Existing Pipe/Trenches/Surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-In-Charge of the Works 4. Providing and erection/ laying of XLPE (E) 11 KV HT Aluminium Conductor Armoured Cable ISI Mark Laid in Existing Pipe/Trenches/Surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-In-Charge of the Works 95 Sq mm 3 core [Through Rate]

[24.2.7.3]LT CABLE 7.3. Supply and erection of suitable compression type brass cable glands for underground Cable :- 25 sqmm to 50 sqmm Cable 2 to 4 Core [Through Rate]

[24.2.7.4]LT CABLE 7.4. Supply and erection of suitable compression type brass cable glands for underground Cable :- 70 sqmm to 95 sqmm Cable 3 to 3½ Core [Through Rate]

[24.2.7.5]LT CABLE 7.5. Supply and erection of suitable compression type brass cable glands for underground Cable :- 120 sqmm to 185 sqmm Cable 3 to 32 Core [Through Rate]

[24.2.7.6]LT CABLE 7.6. Supply and erection of suitable compression type brass cable glands for underground Cable :- 240 sqmm to Cable 3 to 32 Core [Through Rate]

[24.2.7.7]LT CABLE 7.7. Supply and erection of suitable compression type brass cable glands for underground Cable :- 300 sqmm to 400 sqmm Cable 3 to 3½ Core [Through Rate]

[24.2.8.10]LT CABLE 8.10. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 120 sqmm [Through Rate]

[24.2.8.13]LT CABLE 8.13. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 240 sqmm [Through Rate]

[24.2.8.14]LT CABLE 8.14. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work.300 sqmm [Through Rate]

[24.2.8.5]LT CABLE 8.5. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 25 sqmm [Through Rate]

[24.2.8.6]LT CABLE 8.6. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 35 sqmm [Through Rate]

[24.2.8.9]LT CABLE 8.9. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 95 sqmm [Through Rate]

[24.3.3.1]HT CABLE 3.1. Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :70 to 120 sqmm [Through Rate]

[24.3.4.1]HT CABLE 4.1. Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :70 to 120 sqmm [Through Rate]

[24.5.2.4]MISCELLANEOUS ITEMS 2.4. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 90/75 mm outer dia/inner dia [Through Rate]

[24.5.2.5]MISCELLANEOUS ITEMS 2.5. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 120/105 mm outer dia/ inner dia [Through Rate]

[24.7.5]RCC FOUNDATIONS FOR DG SET 5. 250 KVA DG Set [Through Rate]

Supply and erection of lighting arrestor model ISI Marked suitable for 11KV 3 Phase 50 HZ ground neutral system comprising of spare gape type queen gap type in series with non linger resistor element house in Horizontally scale poreclam bushing with line and ground terminal along with mounting clamps conforming to ISS 3070 (Part-I) of 1985 with latest amendment with all labour and material required to the complete in all respect up to entire satisfaction of the Engineer-in-Charge of the work.

Supply , Erection , testing and comissioning of 11 KV outdoor type HT Metering panel complete with CTs , PTs cubical and electronics Meter with accuracy class 0.2 as per requirement / approved by UHBVN. Panchkula Electrical Supply consisting of following : i)Cubical panel free standing floor mounting type made of sheet steel 14 G SWG CRCA sheet with channel iron base frame spray painted with strong synthetic grey channel paint as per size and design approved by UHBVN. PANCHKULA Electrical Supply.Out door Type with outer canopy. ii)3 nos. 11 KV CTs of 0.2 S accurcy (rating as per requirement given by UHBVN Panchkula). iii)1 no. 11 KV PTs 11000/110 volts 10 VA burden 0.2 accuracy suitable for indoor installation of approved make of UHBVN Panchkula Electrical Supply . iv)Digital electronics meter 3 Phase 4 wire 11000 / 110 volts 10 VA burden 0.2 accuracy for recording reading of KWH of make and rating approved by UHBVN Panchkula Electrical Supply with push button display operating system for different kind of readings . v)Foundation of Suitable Size 300mm above ground level made of CC having suitable size to hold metering panel vi)Outer housing fab by 2mm thick CRCA sheet to cover the HT Metering Panel from rain water alongwith agnle iron frame. vii)The cubical panel will be complete in all respect including interconnections , internal wiring with PVC copper cable its testing / approval of all items by UHBVN Panchkula Electrical Supply with a gurantee of one year from the date of commissioning including cost of all labour and material required to complete the job in all respect upto entire satisfaction of Engineer-in-charge of work.

Supply , Erection , testing and comissioning of Stey Set for GO Switch complete in all respect including Disc insulator etc. upto the entire satisfaction of Engineer -in Charge of work.

Supply , Erection , testing and comissioning of GI Fencing 7 Feet High From Finish Floor Level supported with GI Angle/ Channel complete in all repect upto the entire satisfaction of Engineer -in Charge of work.

Supply and Erection of prestressed cement concrete pole 11 Mtr. long 152 mm x 203 mm at top and 152 mm x 368 mm at bottom with working load of 360 Kg. burried 2.20 m in ground with all satisfication of EIC of work. Make as per approved list.

S/E of MS channel 100mm x 50mm x 6mm / MS Flat 50mm x 50mm x 6mm / MS Angle iron 50mm x 50mm x 6mm including cutting bending to the required shape drilling hole carriage Painting loading unloading complete in all respect upto the entire satisfaction of Engineer-in-charge.

Supply and erection of 65mm GI Pipe complete in all respect upto the entire satisfaction of the Engineer-in-charge.

Design, Supply, Erection, Testing and Commissioning of 11 KV, 630A, 25KA for 1sec, SF6 insulated, Manual, Indoor, Non-extensible RMU , type tested in line with latest IEC standards. The RMU shall be suitable for operations at a height up to 1000 meters above sea level and at 40 degree ambient temperature without any derating. The switchgear and busbar shall all be contained in a stainless steel enclosure filled with SF6 at 0.3 bar (300 hPa) relative pressure. The RMU tank shall provide full insulation, making the switchgear insensitive to the environment with degrees of protection of IP67 . The switchgear operating mechanism shall have an IP2X protection and cable chamber shall have IP3X. Accidental overpressure due to an internal arc is limited by the opening of the safety valve, at the bottom of the metal enclosure, away from the operator. An operator situated in front, lateral (A-FLR 21kA – 1sec, downwards exhaust, for tank as well as cable compartment) of the RMU switchboard during an internal fault will not be exposed to the effects of arcing. Internal Arc Type Test Report for IAC AFL R21 kA for 1 sec for both tank and cable box should have been for minimum 3 way / 3 Function RMU. Plug in type of extensibility must be provided and coupling busbar should not be exposed to air to avoid oxidation of busbars. Extension of cubicle should only require 450mm to handle and the gap between the coupled RMU’s must be within 10mm. All operations shall be from front of the RMU, including access to cable bushings. Cable bushings along the sides or the rear of the RMU are not acceptable required to complete the job in all respect upto entire satisfaction of Engineer-in-charge of work. Make as per list attached. 11kV, 2 Way Ring Main Units one LBS plus 1 VCB Each of the above Ring Main Unit shall comprise of the followings: A) Load Break Switch (LBS) each comprising of the following: = 1 No. i) 11 KV, 630A, 25KA for 1sec Manual Load break switch: with built in line side manual earth switch. Earthing should be completed within 2 operations only (i.e 1. Main switch - OFF, 2. Earth switch - ON). LBS shall have 3 positions, open or disconnected, closed and earthed, and will be constructed in such a way that interlocking prevents unauthorized operations. For earth switch, manual opening and closing will be driven by a fast-acting /snap action mechanism, independent of operator action. LBS and earth switch shall have a min of 1000 (M1) mechanical operations , and 5 nos closing operations at rated SC current. LBS should have 100 electrical operations at rated current = 1 No. ii) Position indicator through clear front mimic in line with IEC 62271-103 = 1 No. iii) Live cable indicator with indications (Voltage Presence Indicator) at the front and three inlets provision to check the synchronization of phases. VPI should be of same make as that of RMU = 1 No. iv) Cable box with termination bushing suitable for upto 2 RUN 3Cx300 Sq mm, XLPE cable = 1 No. v) Fault passage indicator (FPI) with in-built Overcurrent, Short Circuit and earth fault indication FPI should have external indication. FPI should act as communicable ammeter as it shall support sharing load data with FRTU. FPI should be of same make as that of RMU = 1 No. vi) Cable Boots suitable for actual cable size = 1 No. vii) Auxilary switch : LBS - 2 NO plus 2 NC, Earth switch - 1 NO plus 1 NC = 1 No. viii) B) Vacuum circuit breaker (VCB) each comprising of the following i) 11 KV, 630A, 25KA for 1sec Manual VCB with spring assisted mechanism and series trip coil: with built in manual line side three position disconnector cum earth switch. Earthing should be completed within 2 operations only (i.e 1. Main switch - OFF, 2. Earth switch - ON). Vaccuum interrupter should be of same make as that of RMU. The circuit breakers shall have 2 positions: open or disconnected and closed. A separate and independent 3 position earthing switch and disconnector shall be fitted to open and earth the cables in such way that interlocks prevent all unauthorized operations. An independent mechanism shall be fitted for the 3 positions earthing switch and disconnector. Circit breaker shall have a min of 2000 mechanical and 2000 electrical operations at rated current and 50 nos of operations at rated short circuit current. Disconnector and earthswitch shall have a min of 1000 (M1) mechanical operations. The earthing switch shall be fitted with its own operating mechanism and manual closing shall be driven by a fast-acting mechanism, independent of operator action. = 1 No. ii) Position indicator through clear front mimic in line with IEC 62271-103 = 1 No. iii) Self powered relay with O/C , E/F protection. Relay should have a front USB port for laptop interface , LCD display ,10 event records, 5 fault records with time stamp, min 2 setting group and keypad for setting parameters for the relay. Relay should be of same make as that of RMU = 1 No. iv) Suitable CT ratio **/1 A, Class 1 / 5P10 , 2.5VA for protection = 1 Set v) Live cable indicator with indications (Voltage Presence Indicator) at the front and three inlets provision to check the synchronization of phases.VPI should be of same make as that of RMU = 1 No. vi) Cable box with termination bushing suitable for upto 2 RUN 3Cx300 Sq mm, XLPE cable.including suiatable touch proof termination kit = 1 Set vii) Cable Boots suitable for actual cable size = 1 Set viii) Mechanical operation counter = 1 No. ix) Emergency trip push button = 1 No.

Supply installation,testing commissioning of Main LT panel with 1.6/2 mm CRCA sheet, chemically treated or Sand Blasting process before powder coating , siemens grey powder coated, Incomer-4p 1250Amp ACB EDO 50KA ICW= 1 Sec 1 no. ( ACB Make: EATON, Siemens 3WA-47B, schneider MVS , G.E, LandT Upower 4.5,) ICS=ICU = ICW = 50KA for 1 sec , ( ACB Microprocessor with Display with Energy release protections LSIG with % Load Bar graph on ACB relase indivigual fault indication on release), Multifunction meter EM6400NG or Equivalent -1 no, Digital voltmeter ,vss- 1set, Ameeter Ass-1set, CT 1200/5 (3 nos), sp mcb 6a, -6 nos, R Y B indicator -1 each, make. Aluminium E-91 grade bus bar 1600amp, DG incomer MCCB 400Amp / 4P / 50KA / LSIG with Display, along with 2 no. contactors 400Amp / 4P Heavy Duty Makes : Schneider, G.E, Siemens, Crompton only. MEtering MFM Em6400NG or equivalent with R,Y,B, indication along with control MCB, CT`s 630/5A-1 set for DG supply. Outgoing : 3P 630Amp / 50KA Thermal Magnetic Adjustable MCCB with spreaders and EROH- 1 set for hybrid Panel feeder , 4 pole 630amp 36ka Mccb Thermal Magnetic ADjustable , -1no, 4p 400amp Thermal Magnetic Adjustable 36ka Mccb -3 nos, 4P 250A, 36KA Thermal Magnetic MCCB- 1 no., 4p 160a , 50ka Mccb Thermal Magnetic Adjustable -2 nos, 4p 100a , 36ka Mccb-3 nos . all accessories should be provided as per satisfaction of engineer incharge. all Mccb with spreader link and ERH. ( MCCB `s Make : Siemens 3VA, Schneider CVS, G.E, Moeller ) Note : All MCCB`s should be ICS=100% ICS, double break current limiting type with 32Amp to 250Amp of same size and 400Amp / 630Amp of same size. All MCCB`s should have spreaders for both sides and EROH along with Shunt for remote tripping as when required. Make as per list attached.

Supply installation,testing commissioning of Essential load panel with 1.6/2 mm CRCA sheet chemically treated or Sand Blasting process before powder coat , siemens grey powder coated, Incomer-4p 400Amp MCCB , 36KA, , -1 No, EM6400NG or equivalent Multifunction meter-1 no, Digital voltmeter ,vss- 1set, Ameeter Ass-1set, CT 4000/5 (3 nos), sp mcb 6a, -3 nos, R Y B indicator -1 each, Aluminium E-91 grade bus bar 1600amp, Outgoing : 4P 250amp Mccb Thermal Magnetic Adjustable,36KA, -2 nos, 4 pole 125amp 36ka Mccb , -2no, 4p 100amp , 36ka Mccb -3 nos, 4p 63a mcb, 10ka Mcb-2 nos all accessories should be provided as per satisfaction of engineer incharge.. all Mccb with spreader link and ERH. MCCB Make: SChneider CVS, EATON, G.E., Siemens 3VA . All MCCB`s should be ICS=100% ICS, double break current limiting type with 32Amp to 250Amp of same size and 400Amp / 630Amp of same size. All MCCB`s should have spreaders for both sides and EROH along with Shunt for remote tripping as when required. Make as per list attached.

Hybrid Power Factor Correction Panel Design, Supply, Installation, Testing and commissioning of cubicle type Semi compartmentalized floor mounted free standing type with separation system OEM Manufactured Hybrid APFC Panel (Active plus Reactive power Factor) (( 60Amp Active plus 250KVAR Reactive Power Factor ) ( OEM Manfuactured at thier factory only) Hybrid panel should have, 433V, 50HZ, 3 phase 4 wire/3 Wire supply. Active part should be modular and have modules of 50/100 A or more, AHF must be intrinsic design of voltage sourced IGBT based intelligent 3-Level topology with 12 IGBT`s with Programmable Microprocessor Controller to maintain Power Factor, Harmonics and Unbalancing. The passive part must be as per IS:16636:2017 or IEC 61921 and 61439 Part -I and II (OEM Factory made) with valid temperature rise test from CPRI. The passive part must be as per the duly housed in epoxy powder coated 2mm thick CRCA steel sheet semi compartmentalized enclosure free standing type with all supports, accessories, switch gears, capacitors, control gears, protections, wiring, interconnections, control MCBs, controllers, reactors, etc. Makes as per list attached All Major components like Capacitor, Reactors, Controller, Capacitor Duty Contactor and AHF module should be of single manufacturer for better operation and maintenance practice. All capacitors should be ISI/BIS Marked with valid CML Number on each name plate. All detuned reactors shall be with CE marking and ROHS compatible, items like capacitors should have valid CPRI type tested as per the relevant IS. Hybrid Panel should be IP-42 and duly housed in epoxy powder coated 2mm thick CRCA sheet steel compartmentalized enclosure free standing type with all supports, accessories, switch gears, control gears, protections, wiring, interconnections, control MCBs and maintain PF,I-THD,V-THD as per IEEE 519-92 etc. as required. Also complete in all respects and having its main components as bellow along with all other standard components ,circuitry and specifications as required: All AHF/Hybrid system must comply following standards. • CE certified valid ROHAS,REACH certificate• Electromagnetic standard FCC 15J,Class-A IEC 61000-4 • IEC-60529 IP-42 • ANSI IEEE Standard 519-2014 (Harmonics LIMITS) • CE/UL-508, IEC 60204-1. EN 50178 NOTE: The following specifications as above must be considered for all panels. Hybrid Power Factor Correction Panel AHF(60 Amp) plus (APFC) 250 KVAR with CAPacitors 525V and Reactors 440VIEC 60076-6 Class H for insulation (=180°C INCOMMER 1 No. of 630 A 4P MCCB / 4P / 50KA Thermal Magnetic Adjustable Trip Unit within in built thermal memory within inbuilt fault indication LED for each faulta such as Overload with setting of 40% to 100% with time delay 10 s at 6 lr, 3 s at 6 lr, 10 s at 7.2 lr, 3 s at 7.2 lr, Neutral protection : 50%, 100% and 150% Ir with time delay 200ms, Earth Fault with setting 20% to 50% with time delay of 100ms /200ms, MCCB should be complete along with Spreaders along with Extended Rotary Handle. Makes : Siemens 3WL, Schneider CVS, G.E, EATON 1 No. of Display MFM meter with 15thorder Harmonic with RS 485 ports.(MODBUS) 3 No. of Phase Indicating and ON-OFF LED Lights 230 V. 1 Set. of Ammeter - digital 3 Phase. 6 No. of MCB 6A-SP-10kA-C-Curve. 1000-Amps (neutral equal size) 3 phase 4 wire 415 volts 50 HZ Aluminium bus bars with colour coded PVC heat shrinkable sleeves. OUTGOING - Active Part: AHF 60 Amp - 1 Nos. Three Lavel Topology 12-IGBT based active technology with gate driver, interfacing, voltage sensing and control cards, heat sinks, cooling fan, current tranducers, SMPS,SSR etc.) each have following. 3 Nos. of High speed Semiconductor fuse 1 No. of Programmable HMI With 7inches LED Display. Passive Part: APFC 250Kvar PArt The Solution should comprise of 350kVAr including Capacitor Duty Contactor, APFC relay and Aluminium Detuned filter reactors 7% with 143% linearity. The capacitor bank should have the following step ratings:50KVARx2no. plus 25KVAR X4no. Capacitor shall be 525V MPP film, IEC 60831-1,2 Compliant, Unique Pressure sensitive disconnector, Class D ( plus 55degC) Heavy Duty MPP type low loss as per standards with overcurrent capability of 1.8xIr and Inrush current capability of 220xIr with Service life in hours 120000 h. Each stage of the capacitor bank should have suitable overload and short circuit protection as defined below. 1 No APFC Relay with 4 CT sensing facility with RS 485 Port. Cap Bank -50KVAR - 3 Nos. (Each Consist) 1 No. 125A 3P MCCB 25 KA with built in protection 1 No. Capacitor Duty Contactor for 60 kvar Capacitor Unit. 2 No. of 33.1 KVAR MPP-H capacitor at 525 V AC with 7% Al wound Detuned Reactor. 1 Set of start/stop PB and On/OFF LED, A/M S.S Cap Bank -25KVAR - 4 Nos. (Each Consist) 1 No. 63A 3P MCCB 25 KA with built in protection 1 No. Capacitor Duty Contactor for 25 kvar Capacitor Unit. 1 No. of 33.1 KVAR MPP-H capacitor at 525 V AC with 7% Al wound Detuned Reactor. 1 Set of start/stop PB and On/OFF LED, A/M S.S Make as per list attached.

Designing, Supply and erection of DG set of 250 KVA capacity with noise controlled devices acoustic of suitable rating, testing and commissioning of diesel generating set, radiator cooled, 3 phase, 4 wire, 50 cycles 415 plus (-)1% volts AC alternator coupled directly through a set of flexible coupling on a common MS fabricated base frame with diesel engine complete with suitable size incoming cable from generator to change over/AMF panel, making 2nd incoming cable connection from transformer, outgoing cable connection from changeover/ standard panel, making second incoming cable connection from transformer, outgoing cable connection from changeover / STD panel to incomer of motor starter panel, fenced enclosure with platform for DG sets complete as per following detailed scope and specifications and directions of Engineer-in-charge. The rating should be at 1500 RPM. a) Diesel Engine b) Alternator c) Battery 24 v. d) Base Plate. e) suitable sq mm suitable core copper cable upto 40 metres. f) Tools, standard panel g) Metering set 415 VAC-1 set (Amp. meter, Volt Meter, ASS, VSS, Phase Indicator, control fuse, frequency meter, CT`s) h) Metering set 60/5A/11 OV (Amp. Meter, Volt Meter) i) Overload protection for DC-1 No. j) Battery Charger 24V DC k)Copper bus bar of suitable size I) KWH meter 96 sqmm size m) Starting fuse button and key switch9on/off) n) Indicating lamps for low lubricated oil pressure, high coolant temperature, set running, load on, De control and other required accessories complete in all respects to the satisfaction of Engineer-in-charge. Make as per list attached.

Supply, Installation, Commissioning, Testing of Air insulated compact Rising Main of capacity 400A/40KA having enclosure made up of 1.6mm thick Electro Galvanised G.I sheet duly powder coated, 4 P Aluminium Bus Bar in convenient sections with support of F-Insulators at suitable distance, suitable for 415 Volt, 50 Hz AC, including fire barriers, vertical brackets, end cover and 2 runs of external Aluminium earhting to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of Work. Make as per list attached.

Supply, Installation, Commissioning, Testing of Air insulated compact Rising Main of capacity 250A/40KA having enclosure made up of 1.6mm thick Electro Galvanised G.I sheet duly powder coated, 4 P Aluminium Bus Bar in convenient sections with support of F-Insulators at suitable distance, suitable for 415 Volt, 50 Hz AC, including fire barriers, vertical brackets, end cover and 2 runs of external Aluminium earhting to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of Work. Make as per list attached.

Supply, Installation, Commissioning, Testing of End Feed Unit of capacity 400 Amp. with MCCB, Extended Rotary handle and Spreader Link (for Compact Air Insulated Rising Main) with all labour and material required to the complete in all respect up to entire satisfaction of the Engineer-in-Charge of the works. Make as per list attached.

Supply, Installation, Commissioning, Testing of End Feed Unit of capacity 250 Amp. with MCCB, Extended Rotary handle and Spreader Link (for Compact Air Insulated Rising Main) with all labour and material required to the complete in all respect up to entire satisfaction of the Engineer-in-Charge of the works. Make as per list attached.

Supply, Installation, Commissioning, Testing of Tap Off-Box of capacity 100 Amp. with MCCB, Extended Rotary handle and Spreader Link (for Compact Air Insulated Rising Main) with all labour and material required to the complete in all respect up to entire satisfaction of the Engineer-in-Charge of the works. Make as per list attached.

Supply, Installation, Commissioning, Testing of Tap Off-Box of capacity 63 Amp. with MCCB, Extended Rotary handle and Spreader Link (for Compact Air Insulated Rising Main) with all labour and material required to the complete in all respect up to entire satisfaction of the Engineer-in-Charge of the works. Make as per list attached.

Supply, Installation, Commissioning, Testing of End Cap of capacity 400A. (for Compact Air Insulated Rising Main) with all labour and material required to the complete in all respect up to entire satisfaction of the Engineer-in-Charge of the works. Make as per list attached..

Supply, Installation, Commissioning, Testing of End Cap of capacity 250A. (for Compact Air Insulated Rising Main) with all labour and material required to the complete in all respect up to entire satisfaction of the Engineer-in-Charge of the works. Make as per list attached.

Supply, Installation, Commissioning, Testing of Rotary Handle of capacity 400 Amp. Without MCCB (for Compact Air Insulated Rising Main) with all labour and material required to the complete in all respect up to entire satisfaction of the Engineer-in-Charge of the works. Make as per list attached.

Supply, Installation, Commissioning, Testing of Rotary Handle of capacity 250 Amp. Without MCCB(for Compact Air Insulated Rising Main) with all labour and material required to the complete in all respect up to entire satisfaction of the Engineer-in-Charge of the works. Make as per list attached.

Supply, Installation, Commissioning, Testing of Rotary Handle of capacity 63 to 100 Amp. with MCCB, Extended Rotary handle and Spreader Link (for Compact Air Insulated Rising Main) with all labour and material required to the complete in all respect up to entire satisfaction of the Engineer-in-Charge of the works. Make as per list attached.

Supply of LED Panel 2`x2` 36/40 Watt, Make asper approved list

Supply of LED Batten 18/20 Watt, Make asper approved list

Supply of LED Downlighter 15 Watt, Make asper approved list

M/s JSB Enterprises (BID ID -1254975)

Highlight Associates and Contractors (BID ID -1254619)