CERTAIN WORKS IN AIRFIELD AREA AT AF STN JAMNAGAR UNDER GE (AF) JAMNAGAR NO 1

Amount

M&L in Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including removal of excavated material exc. 1.50 km but n exc. 5 km and depositing where, complete all specified and directed by Engineer-in-chagre.

Excavating over areas, n exc 1.5 m deep and getting out in soft soil, complete all specified and directed by Engineer in chagre .

Removing excavated material exc. 1.50 km but n exc. 5 km and depositing where, complete all as specified and directed by Engineer-in-charge.

Returning, fillingin, including spreading, leveling, watering and well remming in layets not exc 25cm in hard/dence soil complete all as specified and directed by Engineer-in-charge.

M&L Moorum/red bajri filling in floors or pavings, laid in layers 30 cm thick, spread, levelled and rammed including watering complete all as specified and directed by Engineer-in-charge.

M&L Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engineer-in-charge.

M&L for Cement concrete of type D2 1:4:8 (40 mm graded aggregate) in foundations, filling and mass concrete, complete all as specified and directed by Engineer-in-charge.

Flat Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for Rough finished surfaces of concrete , complete all as specified and directed by Engineer-in-charge.

M&L in Reinforced cement concrete (design mix M-30 ) 20 mm garaded concrete in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete , complete all as specified and directed by Engineer-in-charge.

M & L for rendering 10 mm thick on brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement for surfaces, complete all as specified and directed by Engineer-in-charge.

M&L Pre-cast cement concrete block masonry of type C1 (1:3:6) 20 mm aggregate concrete with solid blocks, exc. 10 cm in width and setting in mortar of 1:6, complete all as specified and directed by Engineer-in-charge.

M&L for prepation of plastered surface of wall and applying two coats of Distemper oil emulsion over one coat of primer, complete all as specified and directed by Engineer-in-charge.

S&F for TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips , complete all as specified and directed by Engineer-in-charge.

Preparation of new steel or iron surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide, primer, complete all as specified and directed by Engineer-in-Charge.

M&L Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 including welding riveting or complete all as specified and directed by Engineer-in-charge. Note:- Work will be executed in parts as per requirement on different part of entire air field area.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement including taking down cement or cement lime plaster or complete all as specified and directed by Engineer-in-charge.

M&L in preparing surface plastered or unplastered on walls with 3 coat of white washing complete all as specified and directed by Engineer-in-Charge.

S&F Second class hard-wood wrought timber frame in scantlings complete all as specified and directed by Engineer-in-charge.

Dismantling framed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed by Engineer-in-charge.

Dismantling boarding, any description, fixed in any position with nails and fixed with screws complete all as specified and directed by Engineer-in-charge.

M&L in hardwood of 2nd class 40mm in thickness planed one side with butt joints and fixed with nails supplied and fixed complete all as specified and directed by Engineer-in-charge.

M&L in French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats complete all as specified and directed by Engineer-in-charge.

M&L in Prelaminated particle board of 25 mm thickness fixed in celling, flat and slopping , exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed by Engineer-in-charge. Note:- the work which include all the cutting , fixing and orientation should be executed as per site requirment . the neccesary accesories required also be executed with this item.

S&F 50mm thickness Butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified and directed by Engineer-in-charge.

S&F 75mm stainless steel handles, fabricated type, anodised complete all as specified and directed by Engineer-in-charge.

S&F stainless steel 5 ball bearing runners 45mm telescopic channel (20inch) full extension load capacity 50kgs, complete all as specified and directed by Engineer-in-charge.

S&F 75mm stainless steel, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-charge.

S&F 25 mm size magnetic catches with Plastic body and striking plate including letting in and fixed complete all as specified and directed by Engineer-in-charge.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.11611979 grade St.-240 or complete all as specified and directed by Engineer-in-charge.

Honest builders (BID ID -3500383)

M/s. Ambabhai K patel (BID ID -3492123)