Construction of Science Block for S.S.L.N.T Mahila Mahavidalaya at Dhanbad under Binod Bihari Mahato Koylanchal University, Dhanbad

Amount

EARTH WORK IN EXCAVATION IN FOUNDATION Trenches in ordinary soil (vide classification of soil item -A) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I.

IN FOUNDATION

EARTH WORK IN EXCAVATION IN FOUNDATION Trenches in ordinary soil (vide classification of soil item -A) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I.

FILLING IN FOUNDATION TRENCHES AND PLINTH in layers not exceeding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Providing coarse clean local SAND IN FILLING in foundation trenches or in plinth including ramming and watering in layer not exceeding 150 mm thick with all leads and 1.5 M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer Incharge (Mode of measurement compacted volume)

Providing designation 75-A, BRICK FLAT SOLING joints filled with local sand including cost of watering,taxes and royalty all complete as per building specification and direction of Engineer Incharge

Providing designation 75-B, one BRICK FLAT SOLING joints filled with local sand including cost of watering,taxes and royalty all complete as per building specification and direction of Engineer Incharge

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and filling BRICK BATS in toilet sunken slab after waterproofing treatment of slab and beam sides including all taxes all complete.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work up to plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum (COLUMN)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum (BEAM)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum (ROOF SLAB)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum (LINTEL BAND)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum (LINTEL)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum (STAIRS)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum (CHAJJA)

Providing, hosting and fixing above plinth level up to floor level precast Reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand ), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , exculuding the cost of reinforcement, with 1:1.5:3 (1cement : 1.5 coarse sand (zone-iii) : 3 graded stone aggregate 20mm nominal size)

Extra for R.C.C./B.M.C./R.M.C. work above floor V level for each four floors or part thereof

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including struting, propping etc. and removal of form for -

Foundation, footings, bases of columns etc.

Columns

ROOF SLAB

Beams, plinth beams,-

STAIRS -

CHAJJA

Edges of slabs and breaks in floors and walls

Under 20 cm wide

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (plan area to be measured)

Suspended floors, roofs, landing, beams and balconies (plan area to be measured)

Providing tor steel reinforcement TMT FE 500 of following dia. rods as per approved design and drawing including carriage of bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction and direction of E/I. (ONLY VALID FOR SAIL & TATA STEEL, JSPL, ELECTRO STEEL LTD. AND VIZAG STEEL)

TOR 8 MMDIA.

TOR 10 MMDIA

TOR 12 -32 MM DIA.

Providing designation 75A brick work in C.M. (1:6) in foundation & plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. thick mortar joints,cost of screening materials raking out joints to 15mm depth , curing, taxes & royalty all complete as per building specification & direction of E/I.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 20mm nominal size)

Extra for providing and mixing waterproofing material in cement conncrete work in doses by weight of cement as per manufacturer's specification.

Providing designation 75B brick work in C.M. (1:6) in foundation & plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. thick mortar joints,cost of screening materials raking out joints to 15mm depth , curing, taxes & royalty all complete as per building specification & direction of E/I.

Providing designation 75 A BRICK WORK in CM. (1:6) in SUPERSTRUCTURE with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening,racking out joints to 15 mm depth,curing, taxes and royalty all complete as per building specification and direction of Engineer Incharge

Providing 125 mm thick REINFORCED DESIGNATION 75 A BRICK WORK in C.M. (1:4) in SUPERSTRUCTURE with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, cost of materials, racking out joints to 15 mm depth, carriage, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of Engineer Incharge .

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing 12 mm Thk. cement plaster(1:6) on inside walls with clean course sand of FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I

Providing 6mm cement plaster(1:4) in ceiling with clean course sand of FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I

Providing 12 mm thick water proof CEMENT PLASTER (1:6) on outside wall with clean coarse sand of F.M.1.5 and waterproofing compound (as per specified and approved) including cost of screening, curing making grooves with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I. (Cost of waterproofing compound will be paid separately)

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Providing & fixing FAN HOOK of 16 mm dia M.S. bar, 1 M long bent to required size and shape, placed in position and fluid in the R.C.C. slab-beam at the time of casting all complete as per building specification and direction of E/I.

Supplying, fitting & fixing 250 x 20 x 6 mm L-type M.S. clamp properly fishtailed including making holes and setting the same in 375 x 125 x 75 mm cement concrete block (1:2:4) with cost of all layout and materials and taxes as per building specification and direction of E/I.

Making 6x6 / 20x6 mm grooves in plaster surface over walls trully horizontal or vertical as specified at regular intervals at all heights including cleaning finishing , scaffolding and curing with all leads and lifts of water all complete as per buildinng specification and direction of E/I. (6

Extra for brick work for each consecutive floor above first floor including watering and scaffolding, all complete as per direction of E/I.

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Extra for PLASTER work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/I.

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

FLOORING WORKS

Providing and laying DOUBLE CHARGE VITRIFIED FLOOR TILES in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08% and confirming to IS : 15622/ ISO 13006, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.30 kg per sqm including grouting the joints with white cement and matching pigments etc. complete.

Providing and laying 6 mm precast white GLAZED CERAMIC TILES in walls over 12mm cement mortar (1:3) and jointed with white cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specification and direction of E/I

with commercial grade colour tiles.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Marble stone flooring with 18 mm th marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm thick base of cement mortar 1:4 (1cement :4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with:

Udaipur Green Marble

Extra for pre finished nosing to treads of steps of marble stone

Extra for marble stone flooring in treads of steps and risers using single length upto 2.00 m

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels

Granite stone slab colour black, Cherry/Ruby red

Area of slab over 0.5 sqm -

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Provinding and fixing 10 mm thick acid and or alkali resistant tiles of approved make and colour using acid and or alkali resistant mortar bedding and joints filled with acid and or alkali resistanting cement as per IS : 4457 complete as per direction of Engineer -in - charge.

In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand)

Provinding and fixing 10 mm thick acid and or alkali resistant tiles of approved make and colour using acid and or alkali resistant mortar bedding and joints filled with acid and or alkali resistanting cement as per IS : 4457 complete as per direction of Engineer -in - charge.

In DADO/ SKIRTING on a bed of 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand)

Providing 50mm thick cement concrete flooring ( 1:2:4 ) with 20mm to 6mm size graded stone chips finished with floating coat of neat cement in panels, including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm cement plaster(1:3) with clean course sand of F.M 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curing taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying matt finished vitrified tile of size 100x100x16mm/ 300X300X16mm having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in out door floors such as footpath, court yard multi models etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as direction of Engineer-in-Charge.

Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. OVER OUTER WALL

Extra for FLOORING work for each consecutive floor above first floor, all complete as per direction of E/I.

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

DOORS & WINDOWS WORKS

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 50 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)

25 mm thick

suppling , fitting and fixing good quality well dressed and well seasoned sal wood work in chaukhat in doors window ,sky light, fanlight and celevitial window opening including wedge over clmps all including application of two coats of wood preservative of approved quality on the surface , building walls and lintel all complete as per building specification and direction of El.

Supplying, fitting & fixing 35 mm th. Solid core type non-decorative single leaf FLUSH DOOR SHUTTERS in doors with block board core blended with high quality phenol formal dehydes synthetic resinboth side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts , handle,cleats aldrop, door stopper & sand blocks & taxes all complete as per detail drawing building specification & direction of the E/I.

Supplying, fitting & fixing 35 mm th. Solid core type non-decorative double leaf FLUSH DOOR SHUTTERS in doors with block board core blended with high quality phenol formal dehydes synthetic resinboth side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts , handle,cleats aldrop, door stopper & sand blocks & taxes all complete as per detail drawing building specification & direction of the E/I.

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-incharge (Frame work shall be paid for separately).

12mm thick commercial ply conforming to IS : 1328 BWR type

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

1.0 mm thick

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):

Rectangular or square

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i. e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium window, ventilator shutters etc. with EPDM / Neoprene gasket etc complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness (weight not less than 10kg/ sqm)

Providing and fixing glazing in aluminium door, shutters etc. with PVC/neoprene gasket etc complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5.0 mm thickness

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Pre-laminated particle board with decorative lamination on both sides

Providing and fixing Double action hydraulic floor spring of approved brand and manufacture I.S.:6315 marked, Hardwyn Make (Model 3000) or equivalent for doors including cost of cutting floors as required, embedding in floors & cover plates with brass pivot and single piece M.S. sheet outer box with side plate etc.complete as per the direction of E/I. WITH STAINLESS STEEL COVER PLATE MINIMUM 1.25MM THICKNESS:-

DOOR WINDOW

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge. (Approved brand - Godrej/ Dorset)

Providing and fixing aluminium round shape handle of outer dia.100 mm with SS screws etc. coplete as per direction of E/I.

Powder coated minimum thickness 50 micron aluminium.

Providing and fixing aluminium hanging floor door stoppers ISI marked anodized (anodic coating not less than grade Ac 10 as per I.S. 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper

Providing and fixing aluminium TOWER BOLTS ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required color or shade with necessary screws etc. complete.

Extra for providing lipping with 2nd class teak wood battens 25mm minimum depth on all edges of shutters (over all area of door shutter to be measured).

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer

Using M.S. angels 40x40x6 mm for diagonal braces

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:

a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass.

d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineerin- Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories

1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr”

2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml.”

3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml”

4. Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm”

5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test” Tests to be conducted on site

6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000ml”

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass (loee glass) of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in- Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.(Payment for fixing of Spandrel Glass Panels in the curtain glazing is included in cost of relevent Item*).

(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. . The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Supplying, fitting & fixing local made COLLAPSIBLE GATE of approved size and make properly fabricated with vertical double channel 20 x 10 x 2 mm at 100 mm center and braced with M.S. flat diagonals 20 x 3 mm with top and bottom rail of T. iron 40 x 40 x 6 mm with 38 dia steel pulleys complete with bolt, buts locking arrangement, steppers, handles including applying a primer coat of read lead paint carriage, hoisting and taxes etc. all complete as per building specification and direction of Engineer Incharge.

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of ClassA category with properties of being termite/borer roof,water/moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 251.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In-Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately.

Supplying, fitting & fixing M.S. GRILL made of 20 x 6 mm flat as per approved design and drawing properly fabricated with joints continuous fitted, welded and finished smooth, hoisting as per building specification and direction of E/I.

Providing and fixing sliding arrangement in racks/ cupboards/cabinets/ Window shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately)

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

WATER PROOFING TREATMENT

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roof terraces etc. consisting of following operations.

Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water proofing compound conforming to IS : 2645 over the RCC slab including cleaning the surface before treatment.

Laying cement concrete using broken bricks/brick bats 25 mm to 100 mm size with 50% of cement mortar of mix 1:5 ( 1 cement : 5 coarse sand ) admixed with proprietary water proofing compund conforming to IS :2645 over 20 mm thick layer of cement mortar 1:5 (1 cement : 5 coarse sand ) admixed with proprietary water proofing compund conforming to IS :2645 to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs

After two days of proper curing applying a second coat of cement slurry admixed with proprietary water proofing compound conforming to IS: 2645.

Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 ( 1 cement : 4 coarse sand ) admixed with proprietary water proofing compund conforming to IS : 2645 and finally finishing the surface with trowel with neat cement slurry and making of 300X300 mm square.

The whole terrace so finished shall be flooded with water for minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the E/I.

With average thickness of 120 mm and minimum thickness at khurra as 65 mm. (WORKS TO BE DONE BY REGISTERED APPLICATOR OF PIDILITE/ SIKA/ ROFF WITH 10 YRS. GUARANTEE.)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying

a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

(WORKS TO BE DONE BY REGISTERED APPLICATOR OF PIDILITE/ SIKA/ ROFF WITH 10 YRS. GUARANTEE.)

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : (Approved Brand - MYK/Asian/ STP)

3 mm thick

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Covering of treated surface with PCC :- Providing 50mm thick Cement concrete M20 (1:1.5:3) maintaining slope in alternate 2mtX2mt panels with approved quality of stone chips of 20mm to 6mm size graded and cleaned sand of F.M. 2.5 to 3 including screening, shuttering, and mixing cement concrete in mixer with admixture of integral waterproofing and placing in position striking curing, taxes and royality all complete as per building specification and direction of E/i. Panels that has been left should be casted next day. There should be 6mm gap betwwen panels. Brand - Sika Plastocrete Plus, MYK proof WP, Fosroc-Conplast X4211 C,. Dr. Fixit Pidiproof LW+.(WORKS TO BE DONE BY REGISTERED APPLICATOR OF ABOVE MATERIALS WITH 10 YRS. GUARANTEE.)

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI?212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

For vertical surface two coats @ 0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm

Providing tuck pointing [1:3] in cement on brick work clean coarse sand of F.M 1.5 FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I

Providing 12mm cement plaster(1:3) with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 1.5 mm th. cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/I.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/I

Providing two coat of snowcem of approved shade and make over a coat of cement of primer on new surface including preparing the plastered surface smooth with sand paper, soaping, curing and taxes all complete as per building specification and direction of E/I.

Finishing walls with Premium Acrylic Smooth exterior paint with silicone additives "Snowcryl - XT" of M/S Snowcem India Ltd, or equivalent of required shade.

New work (Two or more coats applied @1.43 ltr / 10sqm. Over and including base coat of water proofing cement paint Snowcem Plus or equivalent applied @ 2.20 kg./10 sq.m. )

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall suface to prepare the surface even amd smooth complete.

Finishing walls with textured exterior paint of required shade :

13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm

Providing two coats of SYNTHETIC ENAMEL PAINT of approved shade and make over new WOODEN surface including cleaning the surface after removing dirt, scales, grease and sand papering, including cost of scaffolding etc. all complete as per building specification dirction of E/I.

Providing Primer one coat of read lead paint of approved make over new STEEL SURFACE preparing the surface after cleaning, removing rust, dirt, scales, smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing Primer one coat of read lead paint of approved make over new STEEL SURFACE preparing the surface after cleaning, removing rust, dirt, scales, smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing 2 coats of SYNTHETIC ENAMEL PAINT of approved shade and make over STEEL SURFACE grills & railings including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I.

MISCELLANEOUS WORK

Providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners, etc.)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (Approved Brand - Tata Bluescope/ Equivalent)

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm)

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’.

The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.

With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6, (Approved Brand - KNAUF CEILING SOLUTIONS)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recomme-nded jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).

6 mm thick Cement fiber board as per IS: 14862

providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge

Providing & fixing on wall face unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia

Providing & fixing on wall face unplasticised -P.V.C. moulde fittings / accessories for unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion .

Coupler - 110 mm

SHOE - 110MM

BEND - 110 MM

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. (110 MM)

Providing 250 mm wide BRICK DRAIN in cement mortar (1:6) with avarage 150mm. Clear depth and 250 mm apron including cost of earthwork involved with 75m cement concrete (1:4:8) over one brick designation 75A, flat soling in proper grade and slope at the base , the drain dully plastered in C.M.(1:3) with puning over exposed surface all complete as per building specification and direction of E/I.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.

80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete.

1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Supplying and fixing C. I. Cover without frame for MANHOLE. 560MM DIA C.I. COVER (HEAVY DUTY)

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910, on 12 mm dia steel bar confirming to IS: 1786, having minimum cross section as 23 mmX25mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protuded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in tank with 30X20X15 cm cement concrete complete as per design.

Dismantling pucca brick work including stacking serviceable materialsin countable stacks within 15m lead and disposal of unserviceable materials with all lead, all complete as per direction of E/I.

Dismantling plain cement or lime comncrete work including stacking serviceable materials in countable stacks within 15 m lead and disposal of unserviceable materials with all lead, all complete as per direction of E/I.

Dismantling R.C.C. work including stacking serviceable materials in countable stacks within 15m lead and disposal of unserviceable materials with all lead, all complete as per direction of E/I.

Taking down old door and window shutters including stacking serviceable materials in countable stacks within 15 m lead and disposal of unserviceable materials with all lead, all complete as per direction of E/I.

Taking down choukhats in doors including stacking serviceable materials in countable stacks within 15 m lead and disposal of unserviceable materials with all lead, all complete as per direction of E/I.

Dismantling doors, windows and clerestory windows (steel) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead

Taking down C.A. or G.C.I. sheet in roofs with ridges including stacking serviceable materials in countable stacks within 15 m lead and disposal of unserviceable materials with all lead, all complete as per direction of E/I.

DT: Basic rates for 125/115 mm dia Drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH ring Machine all complete including supplying all meterial, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of engineer-in-charge. (Basic rates)

(i) Drilling up to 30 mtr. Depth below G.L. in Rural Area

Supplying, assembling, lowering and fixing in vertical position in borewell unplasticized PVC medium well screen (RMS) pipes with ribs, confirming to IS: 12818, including hire and labour charges, fittings and accessories etc. all complete, for all depths, as per direction of engineer-in-charge.

100 mm nominal size dia. -

Supplying,filling, spreading and levelling stone boulders of of size range 5cm to 20 cm, in recharge pit, in the required thickness, for all leads and lifts, all complete as per direction of Engineer-in-charge.

Supplying,filling, spreading and levelling gravels of size range, 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in the required thickness, for all leads and lifts, all complete as per direction of E/I.

Constructing brick masonary chamber for Underground C. I. Inspection Chamber and bend with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. Cover with frame (light duty) 455X610 mm internal dimensions, total weight of cover with frame to be not less than 38 KG. (weight of cover 23 kg. and weight of frame 15 kg) RCC top slab with 1:1.5:3 mix (1 cement:1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 mix (1 cement:5 coarse sand :10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm th. with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Inside dimensions 455X610mm and 45 mm deep for single pipe line with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete.

150 MM dia R.C.C. pipe

250 MM dia R.C.C. pipe

Supplying fitting and fixing Galvanised wire mesh of average width of aperture 1.4 mm and nominal dia of wire 0.63 mm (2'-0"x2'-0"*2) in position as per specification and direction of E/I.

200/150 mm dia Deep borewell : Cost of drilling 200 mm X 165 mm X 125m deep brewell in all kinds of soil and rock in rural area for installation of pump set with Hydraulic DTH Rig machine, all complete including supplying all all materials, tools drilling rig, Air compressure and equipments, as well as fuel, lubricants and cost of transportation of Rig machine and other vehicle up to the site.

(a) From 0.00 M to 50.00 M below G.L

(b) From 51.00 M to 125.00 M below G.L

(c) From 125.00 M to 200.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

200mm Nominal size dia.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm Dia.

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

Supplying 100mm dia. Submersible pump sets confirming to IS 8034 and motor cvonfirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft ant polypropylene/ norylimpeller. Motor suitable for working on 415 V+10%, 3PH, 50 HZ, AC supply with cable guard, thurst carbon/ fibre bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined no return valve shall be provided with pump. 3 m submersible copper conductor cable in single/ double run and nylon rope as required length shall be provided with each pump.

Submersible pump set 100mm dia (with polypropylene/ Noryl Impeller)

Supplying and fitting of standared make starter pannel board with arrangement of all necessory protection ,including all taxes , royalty etc all complete job as per direction of E/I 5 HP TO 10 HP

Supplying ,fitting & fixing & connecting 3 core 4 sqmm flat copper submerssible cable of Finolex / Hevels make including all taxes ,royalty etc all complete job as per direction of E/I

Supplying and laying /lowering of GI pipe of 50 mm dia including of required fittings solvent etc complete job as per direction of E/I

Making Soak Pit 2.5 m diameter 3.0 meter deep with 45x45cm dry briick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8m long complete as per standerd design .

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

CARRAIGE OF MATERIALS

LOCAL SAND , LEAD - 2P+1K= 3 KM.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

COARSE SAND , LEAD - 9P+1K= 10 KM.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

STONE CHIPS , LEAD - 21P+1K= 22 KM.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

BRICKS , LEAD- 7P+1K= 8 KM.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

DISPOSAL OF EARTH

SANITARY WORKS

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast iron P or S trap, 10 litre low level white P.V.C. Flushing cistern with munally controlled device (handle lever) conforming to IS:7231 Parryware/ Hindware with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.

White Vitreous China Orissa pattern W C pan of size 580 X 440 mm with integral type foot rest.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled devicde (handle lever), conforming to IS:7231, parryware/Hindware/with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.

W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15mm nominal bore

Providing and fixing C.P Soap Dish of aaproved size, shape and approved brand with concealed fittings, complete job.

Providing and fixing C.P Soap Dish of aaproved size, shape and approved brand with concealed fittings, complete job.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing white vitreous china flat back half stall urinal of 580X380X350mm with white PVC automatic flushing cistern, parryware/Hindware with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass with waste fitting as per IS : 2566 P.V.C. trap with outlet grating and other couplings in C.P. brass including parenting of fitting and cutting and making good the walls and floors wherever required..

Single half stall urinals with 5 litre P.V.C. auotmatic flushing cistern

Deduct the 5 litre P.V.C. auotmatic flushing cistern fron urinal

Sl. No. - 7359. rate = Rs. 450+15% = 517.50

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end )

32MM nominal bore.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete.

25mm nominal bore

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 100mm dia. Steel Jali of approved quality.

Providing and fixing stainless steel A ISI 304(18/8) kitchen sink as per I.S.13983 with C.I. Brackets stainless steel plug 40mm including painting of fittings and brackets cutting and making goods the walls wherever required:

kitchen sink without drain board

470x420mm bowel depth 178mm

Providing and fixing C.P Sink cock with swinging casted spout with concealed fitting arrangements.

Providing and fixing unplasticised P.V.C. connection pipe with c.p. nuts collar and bush of approved quality.

15 mm nominal bore with 45 cm length.

Providing And fixing 32 mm waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible Pipe

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (ITEM FOR RAIN WATER, SOIL, WASTE & VENT PIPES)

110 mm dia

Providing & fixing on wall face unplasticised -P.V.C. moulde fittings / accessories for unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion .

Coupler -

Single pushfit Coupler

Single tee with door

Single tee without door

Supplying and fixing 100mm S.C.I. trap with 100mm inlet and 100mm outlet, with all complete.

Supplying and fixing 100mm S.C.I. trap with 100mm inlet and 75mm outlet, with all complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I.(Approved Brand - ASTRAL/ SUPREME)

Concealed work including cutting chases and making good the wall etc..

15 mm nominal dia Pipes

20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement & testing of joints complete as per direction of E/I. (Approved Brand - ASTRAL)

Exposed on Wall

25 mm nominal dia Pipes

32 mm nominal dia Pipes

Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete.

100 MM dia R.C.C. pipe (FOR DRAINAGE OF CHEM. LAB)

150 MM dia R.C.C. pipe

250 MM dia R.C.C. pipe

Constructing brick masonary chamber for Underground C. I. Inspection Chamber and bend with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. Cover with frame (light duty) 455X610 mm internal dimensions, total weight of cover with frame to be not less than 38 KG. (weight of cover 23 kg. and weight of frame 15 kg) RCC top slab with 1:1.5:3 mix (1 cement:1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 mix (1 cement:5 coarse sand :10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm th. with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Inside dimensions 455X610X mm and 45 mm deep for single pipe

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing C.P. brass Health Faucet (Telephonic shower with flexible pipe) including 450 mm long Braided Hoses with all fittings complete job.

Hand Shower - CAT. NO. - JAQUAR, ALD - 573

Providing and fixing C.P. Towel Ring (round) with flange

Towel Ring - CAT. NO. - JAQUAR, AQN - 7721

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

ELECTRICAL WORKS

WIRING POINTS, CIRCUIT WIRING, SUBMAINS, DISTRIBUTION BOARD & MCB's ETC.

Point wiring in pvc conduit , with modular type switch:-Wiring for light point/fan point/exhaust fan/call bell point with 1.5 sqmm PVC insulated copper conductor cable in surface / recessed PVC conduit with moduler type switch,moduler plate,suitable size GI box etc. as required .

Twin control point wiring in pvc conduit with modular type switch:- Wiring for Twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with 2way modular switch ,modular plate, suitable GI box etc. as required.

Power plug wiring in pvc conduit (2x4 sq mm):Wiring for light/ power plug plug with 2 X 4 sq. mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / sub main wiring in pvc conduit:Wiring for submain wiring with the following size of PVC insulated, copper conductor single core cable in surface / recessed PVC conduit as required:

2x1.5 sq.mm.+1x 1.5 sq mm(for toilet switch board +6A socket)

2x2.5 sq.mm.+1x 2.5 sq mm(for switch board )

2x6 sq.mm.+1x 6 sq mm( Sub-Mains DB's)

4 x 6 sq mm +2x6 sq.mm. (Sub-Mains DB's)

4 x 10 +2x6 sq.mm. (Sub-Mains DB's)

4 x 16 +2x6 sq.mm. (Sub-Mains DB's)

Wiring in existing conduit:-Supplying and drawing following sizes of PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit / PVC casing capping / as required.

2x1.5 sq mm

3x2.5 sq mm (For (Lift)

4x6 sq mm(For Lift)

S/F PVC conduit:-S/F of following sizes of PVC conduit alongwith the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required .

20 mm PVC coduit.

25 mm PVC coduit.

Supplying & Fixing of modular type switch / socket :-Supplying and fixing following moduler switch / socket on the existing moduler plate & switch box including connection but excluding moduler plate etc. as reqd.

5/6 amps switch

15/16 amps one way switch

5/6 amps socket outlet

Telephone socket outlet

Supplying & Fixing of modular type electronic fan regulator :- Supplying and fixing stepped type electronic fan regulator on the existing modular plate & switch box including connection but exluding modular plateetc.as required..

Supplying & Fixing of modular type blanking plate.:- Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying & Fixing of modular boxes,base & cover plate:- supplying and fixing following size/ modules, GI boxSupplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc.as required.

1 or 2 Module (78mmX78mmx45mm)

Supplying & Fixing of light plug point with modular type accessories :-Supplying and fixing suitable size GI box with moduler plate cover in the front on surface or in recess including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps. moduler type switch, connections painting etc. as required. (For light plugs).

Supplying & Fixing of power plug point with modular type accessories :- Supplying and fixing suitable size GI box with moduler plate cover in the front on surface or in recess including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps. moduler type switch, connections painting etc. as required. (For power plugs).

Supplying & Fixing of S.P. MCB DB :- Supplying and fixing of following way, single pole and neutral, sheet steel, MCB distribution board,240 volts,on surface /recess, complete with tinned copper bushbar, neutral link, earth bar, din bar, interconnections powder painted including earthing etc. as required. (but without MCB/RCCB/Isolator)

4 way double door (AC ODU)

8 way double door

Supplying & Fixing of T.P MCB DB :- Supplying and fixing following way,horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts,on surface /recess, complete with tinned copper bushbar, neutral link, earth bar, din bar, detachable gland plate, interconnections,powder painted including earthing etc. as required. (but without MCB / RCCB /Isolator)

4 way(4+12)double door Horizontal type

6 way (4+18)double door Horizontal type

8 way (4+24)double door Horizontal type

Supplying and fixing 5 amps. to 32 amps. rating, 240 volts10KA, `B' curve, miniature circuit breaker (10 KA) of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

single pole(6 to 32A)

Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' catagory, miniature circuit breaker (10 KA) of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

single pole(6 to 32A)

6/32 amps.SPN

32 amps.TPN

40 amps.TPN

63 amps. TPN

Supplying and fixing following ways, surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amp tinned copper bus bar, common neutral link, earth bar, din bar, for mounting MCB's (but without MCB's and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

4 way (8 + 12 ), Double door, Vertical type

8 way (8 + 24 ), Double door, Vertical type

32 amps.TP

63 amps.TP

Supplying and fixing following rating and breaking capacity MCCB thermomagenatic release and terminal spreaders in existing cubical panel board including drilling holes in cubical panel,connections etc as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C"curve including connections, painting etc. as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

1 run of cable

2 run of cable

3 run of cable

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and drawing following pair 0.5 sq mm FR PVC insulated copper conductor unarmored telephone cable in the existing surface / recessed PVC conduit as required,

CABLE & CABLE TRAY

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade.of following size on wall surface as required.

Above 35 sq mm and upto 95 sq mm (clamped with 20mmx3mmGI tape)

Laying of PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size exceeding185 sq mm but not exceeding 400 sq mm Direct in ground including excavation ,sand cushioning protective covering and refilling the trench etc as required.

Laying of one number additonal PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade. of size not exceeding 185 sq mm but not exceeding 400 sq mm Direct in ground in the same trench in one tier horozontztal formating including excavation ,sand cushioning protective covering and refilling the trench etc as required.

MV cable laying upto 35 sq mm .in ground:- Laying of one number PVC insulated and PVC sheathed /XLPE power cable of 1.1kv grade of size exceeding 35 sq mm direct in ground including excavation and cushioning ,protective covering and refilling the trench etc as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required Upto 35 sq. mm (clamped with 1mm thick saddle)

Supply of PVC/ XLPE Insulated PVC sheathed heavy duty armoured electric cable with alluminium conductor for working voltage upto and including 1100 volts (conforms to IS:1554,part-1)

50 sq mm x 3.5 core

70 sq mm x 3.5 core

300 sq mm x 3.5 core

6 sq mm x 2 core

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 50 sq. mm (35mm)

3½ X 70 sq. mm (38mm)

3½ X 300 sq. mm (70mm)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

300 mm width X 50 mm depth X 1.6 mm thickness

MAIN DISTRIBUTION BOARDS / L.T. PANEL.

LT PANEL (NORMAL SUPPLY) : -INCOMING (1- sets ) each with following:

400 Amp, MCCB FP -2no, 400A Changover FP-01 No, Ammeter, ASS, CTs, Voltmeter, VSS, Fuses, 2 Sets of Phase Indicating Lights with fuses & following accessories: -

BUS BARS

1sets of 500 Amp, 415V, 3 phase, 50 Hz TPN copper bus bars.

OUTGOING

a)160 Amp, MCCB FP -1 no

b)100 Amp, MCCB FP -4 no

c)125 Amp, MCCB FP -4 no

d)32 amps.TPN-2no

e)40 amps.TPN-2no

f)63 amps. TPN-2no

LT Panel (Normal) as above ( L.G.F)

400A MCCB FP

400A 4 pole on load c/o

160A MCCB FP

125A MCCB FP

25/100 A, MCCB FP

32 amps.TPN

40 amps.TPN

63 amps. TPN

LED INDICATOR LAMP R/Y/B/G

DIGITAL VOLT METER 500V(3phase class 0.5)

DIGITAL A METER 500V(3phase class 0.5)

CT coil of CT tatio 500/5 IS 2705 part 3

50MM*5MM(2.30 KG/MTR)copper strip

25MM*5MM(1.15 KG/MTR)copperStrip

10 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

6 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

1.5 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

S/F wall floor mounted cubical panel board , fabricated with 16 gauge iron sheet suitable for panel mounted switch disconnector ,incliding busbar chamber,insulator and painting etc.as required .(but without busbar copper strip)

EARTHING & LIGHTNING CONDUCTOR.

80mm dia earthing electrode 2mtr Length/ 80mm dia earthing electrode 3mtr Length /50mm dia earthing electrode 2mtr Length/50mm dia earthing electrode 3mtr Length and backfill compound chemical 4 bag (per bag 25Kg)

Providing and fixing 6SWG GI wire at 0.50 m below ground level for coductor earth electrode,including soldering etc as required.

Providing & Fixing of of lighting conductor finial, made of 25mm. Dia. 300mm. Long GI tube, having single prong at top, with 85mm. Dia. 3mm. Thick copper base plate including holes etc. complete as required.

Rivetting, sweating and soldering of copper/GI tape (with another copper/GI tape base of the finial or any other metallic object) as required.

Providing and fixing GI tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as reqd.(for horizontal run)

Providing and fixing GI tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as reqd.(for vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of tinned G.I. bolts, nuts, chuk nuts and spring washers etc. complete as required.

SUPPLY OF LIGHTING FIXTURES & FANS

Supplying, Installation, Testing & Commissioning of following rating surfface mounted LED tube light fitting suitabe for 230v 50Hz single phase supply etc complete as required. Make -

20/22w LED tube light

Supplying, Installation, Testing & Commissioning of following rating recess/ surfface mounted LED round /square shape down light luminaierewith pressure die cast housing for single phase supply voltage luminarie shall be confirm to IS:10322 part-5/section 2 or IEC :62722 with all necessary accessories as required.

12w LED round down light.

18/20w LED round down light.

2"x2"LED panel light

Supplying, Installation, Testing & Commissioning of following rating LEDstreet light luminaiere with pressure die cast housing and toughend glass cover (IP 66 protection )in xisting pole/pipe for supply voltage 100-270 AC 50 Hz luminarie shall be confirm to IS:10322 part-5/section 3and shall be complete with all necessary accessories as required.

120W LED street light.

Supplying, Installation, Testing & Commissioning of following size ceiling fan 3 blades confirming to IS-374:2019including wiring the down rods of standared length (upto 30 cm)with 1.5 sq mm FR PVC insulated copper wire suitable for 230v 50Hz single phase supply etc.as required. (Make - Crompton/ Bajaj/ Havells)

1200mm (48")BLDC 5 star rating 32w Ceiling fan

1400mm (56")BLDC 5 star rating 32w Ceiling fan

Supplying of 9" (230) mm )metal exaust fan with all complete.

Supplying of 12" (300) mm )metal exaust fan with all complete.

Supplying of 15" (380) mm )metal exaust fan with all complete.

Supplying of 16" Wall mounted fan with all complete.

Supplying and fixing of 450 mm 18" metal body Wall fan with speed regulator suitable for single phase 220v 50Hz AC supply.

Providing of bulkhead fitting with 9/10w LED bulb.

ERECTION OF LIGHTING FIXTURES ,FANS

Supplying and fixing 2 pin 5A ceiling rose on the existing junction box wooden block including connection etc ,as required.

Erection of wall bracket / ceiling fittings of all sizes and shapes ontaining upto two GLS lamp per fitting complete with all accessories including connection etc as required.

Installation of exhaust fan upto 450 mm. sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connections, testing, commissioning etc. as required.

Providing, supplying, testing and commissioning Silent type D G Set capacity of 200 KVA with AMF panel IS/ IEC-60034-1 IS:1460 IS 13018including all accessories and all fittings complete job.

EARTHING & ONLINE UPS SYSTEM

80mm dia earthing electrode 2mtr Length/ 80mm dia earthing electrode 3mtr Length /50mm dia earthing electrode 2mtr Length/50mm dia earthing electrode 3mtr Length and backfill compound chemical 4 bag (per bag 25Kg)

Providing and fixing 6SWG GI wire at 0.50 m below ground level for coductor earth electrode,including soldering etc as required.

roviding 5KVA online UPS single phase input and single phase output power system of input Voltage range 110 V AC +/- 5% -300V AC +/- 5% frequency range 40 Hz - 60 Hz >/= 0.90 @ full load, and output voltage range 200V/208/220/230/240V AC, Voltage regulation distortion +/- 1% Frequency range 50Hz+/- 0.25 Hz or 60 Hz +/- 30 Hz Harmonic distortion -< 2% THD (Linear load) : 4% THD (Non-linear load) efficiency - 88/83%.

Providing 10KVA online UPS single phase input and single phase output power system of input Voltage range 110 V AC +/- 5% -300V AC +/- 5% frequency range 40 Hz - 60 Hz >/= 0.90 @ full load, and output voltage range 200V/208/220/230/240V AC, Voltage regulation distortion +/- 1% Frequency range 50Hz+/- 0.25 Hz or 60 Hz +/- 30 Hz Harmonic distortion -< 2% THD (Linear load) : 4% THD (Non-linear load) efficiency - 88/83%.

Providing 20KVA online UPS three phase input and three phase output power system of input Voltage range 110 V AC +/- 5% -300V AC +/- 5% frequency range 40 Hz - 60 Hz >/= 0.90 @ full load, and output voltage range 200V/208/220/230/240V AC, Voltage regulation distortion +/- 1% Frequency range 50Hz+/- 0.25 Hz or 60 Hz +/- 30 Hz Harmonic distortion -< 2% THD (Linear load) : 4% THD (Non-linear load) efficiency - 88/83%.

FIRE FIGHTING WORKS

Supply, Installation, Testing and Commissioning of electric driven, centrifugal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC with IP 55 Protection for enclosure, horizontall foot mounted with class F insulation , complete in all respect as required or as directed by engineer incharge.

Main Fire Pump

Standby Deisel Engine Pump

Jockey Pump

Terrace Booster Pump

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42.

For Pump Room

Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination with compression gland & bimetalic lugs, and support etc.complete as required

4 × 10 sq.mm.(aluminium)

2 × 2.5 sq.mm.(Copper) to be laied in 5 pairs for engine

2 × 1.5 sq.mm. in Conduit

Providing and fixing IS marked Gate Valve / Foot Valve (incase of -ve suction) complete with companion flanges, bolts, nuts, rubber insetions etc.

200 mm diameter

150 mm diameter

Providing and fixing IS marked butterfly valve (PN 1.6) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

Providing and fixing check valve (NRV) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing, laying, testing & commissioning of IS 1239 marked black M.S pipe including all fittings i.e bend, elbows, tees, flanges, reducing socket, nuts and bolts, gaskets etc fixed with welded / screwed joints. including necessary excavation, backfilling, removal of surplus soil etc. min. 1 mtr deep excavation and wrapping with anticorrosive treatement with 4 mm thick asphalt tape as per IS:10221, refilling the trench etc. OR fixed with screwed or welded joints, hanged with clamps, hanger supports, dash fasteners, bolts, nuts, rubber insertions etc including threading, cutting, welding, edge preparation, painting of approved colour over two coat of primer, cutting & making good the wall/ floor wherever required, complete as required or as directed by engineer incharge. Make:Tata/Nezone/Jindal

200 mm diameter

150 mm diameter

100 mm diameter

80 mm diameter

65 mm diameter

50 mm diameter

40 mm diameter

32 mm diameter

25 mm diameter

Providing and fixing S.S Fire Hydrant Valve of approved quality with 63 mm female, instant, ovlique, single outlet, 80 mm flanged inlet, brass spindle, cast iron wheel m A.B.S. blank cap and chain. conforming to IS: 5290 complete with companion flange, bolts, nuts, rubber insertion / compressed asbestos gasket etc. and painted in fire red colour.

Providing and fixing swinging, wall mounting type First Aid Hose Reel of approved quality and made from compresed steel sheet with dust cover, cast iron brackets including 30 m long, 19 mm nominal bore, high presure braided rubber hose as per IS:444 Type hose guide, PVC shut off nozzle with 6 mm outlet and 25 mm nominal bore gun metal inlet valve, bolts, nuts rubber insetion etc. painted in Fire red colour including cutting and making good the walls wherver required.

Providing and fixing in position 63 mm nominal bore and 15 m long synthetic fibre, CP fire hose pipe of approved make bearing IS: 636 -1988 type A mark and having TAC and MMD approved with a pair of 63 x 63 mm gun metal instantaneous type, heavy duty delivery hose coupling (conforming to IS: 903) bound and riveted to the hose pipe with copper rivets and copper wire complete.

Providing and fixing in position short SS brach pipe of approved quality with 63 mm male instatneous type inlet and 15 mm outlet nozzle complete conforming to IS : 903

Providing and fixing Standard response Upright / Pendant sprinklers (With Covers, white / ivory colour) with quartzoid bulb overating temperature 68 degree centgrade, of 15 mm orifice and k factor 80 (5,6) made out of forged brass and chrome finish. Make:Safex/Atasee/Tyco

Supplying, installation, testing & commissioning of sprinkler flexible pipe of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.

Supplying, fixing, testing & commissioning of 1 set of 63mm two way instantaneous fire brigade connection (FBC) with inbuilt NRV comprising of SS and four SS instantaneous male inlet coupling confirming to IS:604 with plug and cap with chain as required with nut & bolts, washers, high pressure gasket as required.

Supplying, installation, testing and commissioning of optical type Smoke detector and mounting base with LED light complete as required. Make:Qutak/Honeywell/Seimens/Bosch

Supplying, installation, testing & commissioning of response indicator on surface/recessed having two LED with cover complete with all connections etc as required

Supplying, installation, testing and commissioning of duel tone electronic hooter / Flasher / Strobe suitable for wall mounted complete as required. Make:Honeywell/Seimens/ Qutak/ Bosch

Supplying, installation, testing and commissioning of manual call box in suitable enclosure with arrangement to raise the alarm when the glass is manually broken complete as required. Make:Honeywell/Seimens/Qutak/Bosch

Supplying, installation, testing and commissioning of microprocess base main fire alarm control panel with LCD Display lights. The panels shall have 240 volts AC power supply automatic Battery charger 24 Volts sealed lead acid maintenance free battries as complete with batteries, battery charger illuminated numeric digram complete as required. Make:Honeywell/ Seimens/ Qutak/ Bosch

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required. Make:Honeywell/ Ahuja/ Bosch

Supplying, installation, testing & commissioning of ceiling/wall mounted Pubmic announcement speaker, 3/1.5 Watt in ABS enclosure complete as required. Make:Honeywell/ Ahuja/ Bosch

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required. Make:Honeywell/ Ahuja/ Bosch

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required. Make:Honeywell/ Ahuja/ Bosch

Providing and laying 19mm dia PVC conduit complete with required junction boxes in recessed / surface system with PVC insulated copper conductor cable of 2x1.5 sq.mm. in existing conduit as required. Make:Polycab/Mescab

LANDSCAPING

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from local or other approved source including royalty and cariage up to 1 km. (Manure measured in stacks will be reduced 8% for payment). Screened through sieve of I.S. designation 4.75 mm.

Rough dressing the trenched ground including breaking clods.

Fine dressing the ground

Spreading of sludge, dump manureor / and good earth in required thivkness(Cost of sludge, dump manure or / and earth to be paid seperately).

Mixing earth and sludge or manure in proportion specified or directed.

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Callistemon lanceolatus of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Callistemon lanceolatus of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus bengalensis (varigated) of height 75-90 cm., multibranched in earthen pots of size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.

Dreaceana pendanus, well developed, having 6 to 8 suckers with helthy foliage in 25 cm size Earthen pot /Plastic pot

Dianella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot / Plastic Pot.

Euphorbia milli hybrid variety, having ht. 30 cm to 45 cm with multi branch, full bloom, fresh and healthy leaves in 30 cm size of Earthen Pot / Plastic Pot.

Adenium Obesum well developed with fresh & healthy 4 to 5 branch 60 to 75 cm ht. plant in 40 cm size Earthen Pot/ Plastic Pot

Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot / Plastic Pot.

Dracaena Mahatma having ht. 30 cm to 45 cm, well developed, fresh and healthy foliage in 20 cm size of Earthen pot / Plastic pot.

Providing and stacking of Butea frondosa (Flame of Forest) of height 60-75 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Foxtail Blue palm/ Fan palm of ht. 180-210 cm bottom girth 25-30 cm well developed in big size HDPE bags as per direction of the officer-in-charge.

AIR-CONDITIONING (SPLIT)

Supplying, installations, testing and commissioning 1.0 Tr Inverter Split AC with 5 star rating, which includes low power consumption and as it is an inverter based technology i.e. will expand its cooling capacity according to the room temperature having 100% copper tube, Superslit Find and also have smooth air and clean air flow features with cooling system, Intelligent Defrost mode including drain pipe, copper pipe of required length, outdoor ms stand (painted) as required and complete job. Approved Brand - Hitachi/ Daikin/ Voltas/ Toshiba.

Supplying, installations, testing and commissioning 1.5 Tr Inverter Split AC with 5 star rating, which includes low power consumption and as it is an inverter based technology i.e. will expand its cooling capacity according to the room temperature having 100% copper tube, Superslit Find and also have smooth air and clean air flow features with cooling system, Intelligent Defrost mode including drain pipe, copper pipe of required length, outdoor ms stand (painted) as required and complete job. Approved Brand - Hitachi/ Daikin/ Voltas/ Toshiba.

Supplying, installations, testing and commissioning 2.0 Tr Inverter Split AC with 5 star rating, which includes low power consumption and as it is an inverter based technology i.e. will expand its cooling capacity according to the room temperature having 100% copper tube, Superslit Find and also have smooth air and clean air flow features with cooling system, Intelligent Defrost mode including drain pipe, copper pipe of required length, outdoor ms stand (painted) as required and complete job. Approved Brand - Hitachi/ Daikin/ Voltas Toshiba..

Copper tube of size 1/4"for split ac unit 1/1.5/2/3 tr capacity including nitride rubber insulation.

Copper tube of size 1/2" for split ac unit 1/1.5/2/3 tr capacity including nitride rubber insulation.

4 KVA wall mounted automatic voltage stablizer from range 140v to 280v .

5 KVA wall mounted automatic voltage stablizer from range 140v to 280v .

Drain pipe for AC

Outdoor stand for 1/ 1.5tr split AC.

Outdoor stand for 2 tr split AC.

Non Schedeule

Providing and Installing, Testing & Commissioning of 13 Passenger automatic (machine room less) Lift - 1no., including one year free maintenance which will be start from handing over the lift, all taxes and all complete as per following detail specifications. APPROVED BRAND - OTIS/ SCHINDLER/ JOHNSON

PRODUCT- GeN2- Nova MRL

DETAIL- GeN2-Nova_MRL-1MPS

CAPACITY(Kgs) - 884 kg 13 persons.

SPEED(mps) - 1mps.

RISE (M) - 21.9 M

STOPS - 7 Stops with (all opening on the same side)

CONTROLLER TYPE - ACD5-MRL

DRIVE - VF Regenerative (Closed Loop)

POWER SUPPLY - 400/415 Volts (3 phase AC)

OPERATION - Full collective operation.

CAR GROUP - One car (simplex)

MACHINE - PM Gearless (Located in shaft on top of guide rails)

TRACTION MEDIA - Flat Coated Steel Belt.

CAR FINISH -

Rear Mid Panel= Stainless Steel # 4 (Hairline)

Rear Corner Panel= Stainless Steel # 4 (Hairline)

Side Panel= Stainless Steel # 4 (Hairline)

Front Panel= Stainless Steel # 4 (Hairline)

FALSE CEILING TYPE - CD-41

FALSE CEILING FINISH - Stainless Steel # 4 (Hairline)

VENTILLATION - Cross flow fan.

HAND RAILS - Stainless Steel Mirror Finish Handrails on rear car panels

FLOORING - Vinyl Tiles

CAR DOOR FINISH - Stainless Steel # 4 (Hairline)

LANDING DOOR FINISH - Stainless Steel # 4 (Hairline)

FIRE RATED DOORS - Not Available

PIT DEPTH - 1350

OVER HEAD - 4300

CAR & HOISTWAY DOOR TYPE- Central opening (CO) doors

DOOR OPENING (W x H- MM )- 900mm W x 2000mm H

DOOR OPERATOR- DC Door Operator

COP for stops <= 12 (950mm) in Stainless Steel #4(Hairline)

CAR POSITION INDICATOR- Monochrome LCD-Blue Background & White font Dot matrix (LED) Scrolling Display

HALL FIXTURES- O2000 Pan Type Fixture ,

HALL FIXTURES FACE PLATE- Stainless Steel #4(Hairline)

HALL BUTTON ARRANGEMENT- LCD Monochrome type

STANDARD FEATURES- Anti-nuisance Car Call Protection Independent Service (for Duplex only) Overload Device Nudging Emergency Car Light Unit Infrared Curtain Door Protection Door Time Protection Emergency Alarm Button Extra Door Time of Lobby & Parking Door Open/Close Button Manual Rescue Operation Belt Inspection Drive Auto Fan Cut Off

OPTIONS INCLUDED- Grounding Switch, Automatic Rescue operation, Voice Synthesizer, Audible Car Call Button, Emergency Power Operation, Parking Key Switch ,

Supply, installation , testing & commissioning of NVR 32 Channel: Connect Up to 32 IP Cameras, Up to 8 Megapixels Resolution, HDMI output with 4k output and VGA output with 2MP Output , Support H.265,H.264, MJPEG, Incoming Bandwidth 256 Mbps, 4 SATA Hard Disks, ANR Technology, 4 SATA interfaces for 4 HDDs and capacity of each HDD upto 6TB, 2 USB at least 1 × USB with 3.0, Serial interface:1 RS-485, 1 RS-232, Alarm I/O 16/4, 2 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, Multiple network monitoring: Web viewer, CE, FCC, UL certified. APPROVED BRAND - HIKVISION, DS-7732NI-k4/ EQUIVALENT.

Supply, installation , testing & commissioning of 2 Megapixel Fixed Lens Camera IR Dome Type: 1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8mm Fixed lens, 0.028 Lux at F1.2, ICR, ONVIF, support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, IK10, Edge Anlalytics- Line crossing detection, Intrusion detection, Inbuilt Audio Motion detection, Scene change detection, video tampering, UL, CE, FCC certified. APPROVED BRAND - HIKVISION DS-2CD3121G0-IUF/ EQUIVALENT.

Supply, installation , testing & commissioning of 2 Megapixel Fixed Lens Camera IR Bullet Type: 1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, inbuilt audio Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Video tampering, UL, CE, FCC certified. APPROVED BRAND - HIKVISION DS-2CD3021G0-IUF/ EQUIVALENT.

Supply, installation, testing and commissioning of outdoor 2MP, VF LENS , 2.8MM TO 12MM, resolution 1920*1080 fixed lens Color Indoor AV Camera, 1/3" CMOS, H.264/MJPEG High-profile, dual Stream support, True Day & Night (TDN) with , Wide Dynamic Range (WDR), Open Network Video Interface Forum (ONVIF) Profile S & G - TF card support (128 GB), IP66 & IK 10 Rating, Power Over Ethernet (POE), IR distance upto 30 Meter. APPROVED BRAND - HIKVISION DS-2CD3056G2-IS / EQUIVALENT.

Supply, installation , testing & commissioning of POE switch of 10/100/1000 Mbps on each Ethernet port. The switch shall be mounted on rack. The rate shall also include cost of power supply and providing end termination.

24 port 10/100/1000 Mbps managed Giga Byte POE Switch. Approved Brand - One Touch, OT-1724P/ Equivalent.

16 port 10/100/1000 Mbps managed Giga Byte POE Switch. Approved Brand - One Touch, OT-1716P/ Equivalent.

HDMI Splitter” is a unit whereby you can send your HDMI output of set-top boxes, DVD Players, D-VHS Players, PC's and other HDTV devices. Approved Brand - Mile Stone ML 401 HMVS/ Equivalent.

Supply, drawing and connecting of cat-6, UTP cable with conduit for cctv. Approved Brand - D-LINK/ Polycab NCB-C6UGRYR-100/ Equivalent)

Supply , Fixing of 6U Racks for POE switch installation in floor wise. Approved Brand - D-LINK NWR-6U-5550-GR

Supply , Fixing, Commissioining of 50 Inch Monitor for CCTV. Approved Brand - LG/ Samsung.

Supply , Fixing, Commissioining of HDMI cables for connecting monitor to NVR. Approved Brand - 4K/ Equivalent.

Supply , Fixing, Commissioining necessary accessories for cctv , nvr and monitors with all complete job.

AUDIO SYSTEM FOR MEETING ROOM

Supplying, Installation, Testing & Commissioning of Digital Chairman Discussion /Conference Unit with Removable Microphone of minimum Length 400mm Chairman Discussion Unit with built-in Digital Signal ProcessingUnit with Priority and Next-in-Line Configuration Priority button silences all delegate microphones and allows only the chairperson to speak; Next-in-line button gives the floor to the next speaker in a waiting list of speakers who requested to speak. User Button with Feedback; Shielded microphone, immune to mobile phone interference, High-quality integrated loudspeaker; Headphone output with Volume Adjustment Loop-through, daisy-chain cabling; Unit with Bi color bar indicator Compatible Screw Lock Microphone of length 400mm Different LED Signalling for Mic On/Off OR Request-to-Speak Push Button or better Audio Quality 16Bit digital; Frequency response: 25 Hz-15,000 Hz (± 3 dB) or better Microphone with 400 Gooseneck Length; Polar Pattern: Unidirectional, Cardioid Max SPL @ 1kHz: 110 dB SPL (1% THD+N) or better S/N Ratio: > 67 dB(A); sensitivity: (-40.5±2) dBV @ 1Pa, 1KHz or better Microphone with Ring Indicator to light up Red when active and Green when in Request Connection: Screw Lock Material: Brass; Certification: CE need to submit; 2M CAT5e cable from the same OEM Approved make : Televic / Bayerdynamic / Marcony Technology / Audix

Supplying of Digital Delegate Discussion / Conference Unit with Removable Microphone of minimum Length 400mm Delegate Discussion Unit with built-in Digital Signal Processing Unit with Microphone On / Off Button; User Button with Feedback Shielded microphone, immune to mobile phone interference High-quality integrated loudspeaker; Headphone output with Volume Adjustment Loop-through, daisy-chain cabling; Unit with Bi color bar indicator Compatible Screw Lock Microphone of lenght 400mm Different LED Signalling for Mic On/Off OR Request-to-Speak Push Button Connectivity: 2 digital bus connections (IN/OUTinterchangeable), Headphone connection. Audio Quality 16Bit digital; Frequency Response: 25 Hz-15,000 Hz (± 3 dB) or better Microphone with 400 Gooseneck Length; Polar Pattern: Unidirectional, Cardioid Max SPL @ 1kHz: 110 dB SPL (1% THD+N) or better S/N Ratio: > 67 dB(A); sensitivity: (-40.5±2) dBV @ 1Pa, 1KHz or better Connection: Screw Lock Microphone with Ring Indicator to light up Red when active and Green when in Request Material: Brass; Certification: CE need to submit; 2M CAT5e cable from the same OEM Approved make : Televic / Bayerdynamic / Marcony Technology / Audix

Supplying, Installation, Testing & Commissioning of Conference connection cable, 10m, black and other interconnecting cables, jacks etc should be from The Same Brand and Interconnecting cables, Microphone cables, speaker cables, special Cat-5 cables for Conference system, PVC Conduit, Power Sockets etc.

Supplying, Installation, Testing & Commissioning of Two way passive loudspeaker including wall mount bracket

Supplying, Installation, Testing & Commissioning of Digital Mixing amplifier - Suitable for above Speakers

LECTURE THEATRE SOLUTION

Supplying, Installation, Testing & Commissioning of Digital Podium with in built Audio and Digital system Smart Rostrum has PC with i3 processor, 4GB RAM, 500 HDD, DOS and Keyboard/Mouse, and can be customized to as per the requirement. Smart Podium has sliding top tray to place Laptop which allows presenter to display any multimedia file instantly. It is fully compatible with all types of Projectors. It has switching plate with buttons on the top, which allows you to display desired projection output, We integrate high quality, echo-free and branded audio equipment in Smart podiums, All cables and connectors inside the podium are tagged and well managed to simplify the structure complexity. 18” gooseneck microphone from premium brands integrated with the Smart Podium. It has 2 XLR ports on the top. All the doors, drawers, trays and shelves are lockable to avoid unauthorised access. It has in-built anti-theft mechanism. Switcher helps to switch the projection among different devices, while splitter helps to split the display for multiple outputs. Smart podium should have all the required input/output ports such as USB, VGA in/out, HDMI in/out, LAN, Audio in/out, XLR, Power and so on. Podium allows you to connect smart board with the projector directly, and helps you to conduct interactive lectures. It integrates full HD Document Camera which helps to project live document/object for audience with greater clarity, Podium has 4 caster wheels which enable it to move easily and effortlessly. Controller helps to operate all the electric & electronic devices using its touch screen etc. Preferred Brand – VAC / INGRESS / ITC / LIBERTY

Supplying, Installation, Testing & Commissioning of Audio Power Amplifier: OPERATION MODES Stereo Mode Bridged-Mono Mode Load 8Ohm 4Ohm 8Ohm 4Ohm 70V (22Ohm) 100V (33Ohm) Maximum Continuous Power (@1khz, 1% Thd) 2 x 140W 2 x 140W 1 x 280W 1 x 260W 250W 240W Maximum Dynamic Power (@1khz, 1% Thd) 2 x 200W 2 x 275W 1 x 550W 1 x 550W 550W 550W Frequency Response 20-20kHz (+/-0.3dB) Peak Output Current 25A Dynamic Range 112dB (A-weighted) Noise Level -76dBu (A-weighted) Distortion (1kHz@1W/8Ohm) 0.003% Distortion (1kHz@50W/8Ohm) 0.011% (Stereo) 0.004% (Bridged-Mono) Crosstalk (1kHz@1W/8Ohm) -95dB Gain 26dB/32dB Maximum Input Level +24dBu Amplifier Version QX-300A QX-300D Input Type Analogue Balanced 3-pin Phoenix (5.08mm pitch) Dante RJ-45 (AES67 Compatible) with RJ-45 Link Input Sensitivity +7dBu/+4dBu -4.5dBFS/- 1.5dBFS Input Impedance 10kOhm - Maximum Input Level +24dBu 0dBFS Output Resistance 22.5mOhm/43.6mOhm Front Controls Volume Adjust, 80Hz HPF Enable, Bridged-Mono Enable, Limiter Enable, Auto-Standby Enable) Preferred Brand – QUEST / EQUIPSON (WORK) / CROWN / MAYERSOUND

Supplying, Installation, Testing & Commissioning of Wall Mounted Weather Proof Speakers Max SPL *calculated 112 dB Sensitivity *5-band average 93 dB Frequency Response 75Hz – 20kHz±2dB Impedance 16Ω Transformer Taping 100V 20w/30w/40w/60w 70V 10w/15w/20w/30w Amplifier Power RMS 100W Peak 200W Transducers HF 25mm Titanium Dome Tweeter LF 8” High Performance Polypropylene Woofer Directivity *H x V 150° x 120° -10dB Connections Captive Screw Terminal Plug (In/Thru) Environmental Ingress Rating Speaker Cabinet IP56 (IP67 when used with IPMX1 kit) Dimensions *H x W x D 345 x 202 x 243mm Net Weight 4.3 kg Shipping Weight 6.0 kg Preferred Brand – QUEST / EQUIPSON (WORK) / CROWN / MAYERSOUND

Supplying, Installation, Testing & Commissioning of 6 channel Audio Mixer. Digital Echo 20 – 400 m/s. Frequency 25 Hz – 25 KHz. MP3 Player with Bluetooth, Display & Remote available. Input Gain: –50 dB to 6 dB gain range with overdrive indication.. Output: 0 dBm / 17 dBm (775mv / 5.5v). Equalization: Bass & Treble ±5 dB. Controls: Gain, Eq., Pan, Echo, Fader. Power Supply: 220V 50Hz AC ± 10% (In separate enclosure) Dimension: 295 (W) x 165 (D) x 80 (H) mm. Weight: 1.630 kg (approx.) Preferred Brands – Shure / Equipson / Bose/ Mayersound/ STRANGER

Supplying, Installation, Testing & Commissioning of Wireless UHF Lapel / Collar Microphone system Specifications Audio Input Level: –20 dBV maximum * Input Impedance: 22 kΩ RF Output (dependent on applicable country regulations): HI power mode: 10 mW maximum * LO power mode: 1 mW maximum Weight: 270 g (10.2 oz.)(without batteries) * Housing: Molded ABS Power Requirements: 2 “AA” size alkaline or rechargeable batteries Preferred Brands – Shure / Equipson / Bose/ Mayersound/Audio Focus/

Supplying, Installation, Testing & Commissioning of Green Chalk Board, Size 6 ft x 4 ft. Green ceramic board 1200mm x 1800mm - The writing surface shall be made of steel sheet of thickness 0.3 to 0.4 mm having vitreous enamel coating of 0.11 mm minimum thickness of top and 0.03mm minimum on the back with free from waviness and show no scratches on using HB to 3H pencils for writing. The surface of the writing board shall show excellent eraseabilty when specified writing medium is used. The core material should be 7mm thick MDF. Backing shall be of electro galvanised steel sheet. The board shall secured from all side with extruded aluminum alloy hollow section frame duly anodized and shall have front: 20mm, side: 16mm and wall thickness: 1.2mm. 4 nos. ABS corner grey color should be provide at all corners of the board.

Supplying, Installation, Testing & Commissioning of connection cable, interconnecting cables, jacks etc and Interconnecting cables, speaker cables, PVC Conduit, Power Sockets etc., suitable cabinet for storing and operating the full system

MINI AUDITORIUM (SOUND SYSTEM, STAGE CRAFT & LIGHTING OF THE STAGE / DIAS)

Supplying, Installation, Testing & Commissioning of 15” powered 2-way loudspeaker, Model QM 4 Specifications Max SPL *calculated 127 dBSPL Sensitivity *5-band average 99 dBSPL Frequency Response 60Hz – 20kHz Amplifier Power RMS: 380W Peak: 470W Transducers HF: 34mm Compression Driver LF: 15” High Power Woofer Directivity *H x V 85° x 75° Connections XLR+¼” In, XLR Out Dimensions *H x W x D 705 x 462 x 440mm Net Weight 21.5kg Shipping Weight 26kg Preferred Brands – Quest / Audio Focus / Mayer Sound / Bose.

Supplying, Installation, Testing & Commissioning of Wall Mounted Weather Proof Speakers Max SPL *calculated 112 dB Sensitivity *5-band average 93 dB Frequency Response 75Hz – 20kHz±2dB Impedance 16Ω Transformer Taping 100V 20w/30w/40w/60w 70V 10w/15w/20w/30w Amplifier Power RMS 100W Peak 200W Transducers HF 25mm Titanium Dome Tweeter LF 8” High Performance Polypropylene Woofer Directivity *H x V 150° x 120° -10dB Connections Captive Screw Terminal Plug (In/Thru) Environmental Ingress Rating Speaker Cabinet IP56 (IP67 when used with IPMX1 kit) Dimensions *H x W x D 345 x 202 x 243mm Net Weight 4.3 kg Shipping Weight 6.0 kg Preferred Brands – Quest / Audio Focus / Mayer Sound / Bose.

Digital Amplifier, 4 channel @ 1500 watt per channel. Specifications Wake On Music, Auto-Mute (1ms wake-up), Limiting on High Temperature Amplifier Protection Systems Thermal protection, Over-Current Protection, DC Protection, HF Protection Mains Input Voltage Range 85VAC - 265VAC Standby Power Consumption 4.9W Muted Power Consumption 25W Idle Power Consumption 50W Standard Power Consumption (Pink Noise@ 1/8th Rated Power, 8Ohm) 500W Mains Connector powerCON Output Connector SpeakON per channel Dimensions (H x W x D) 88 x 482 x 416 mm (3.5 x 19 x 16.4") Weight 12.4kg (27.3 lbs) Accessories Mains Cable, Feet, User Manual, Euroblock Plugs Frequency Response 20-20kHz (+/-0.3dB) Peak Output Current 40A Dynamic Range 111dB (A-weighted) Noise Level -67dBu (A-weighted) Distortion (1kHz@1W/8Ohm) 0.004% Distortion (1kHz@50W/8Ohm) 0.003% Crosstalk (1kHz@1W/8Ohm) -90dB Gain 32dB Maximum Input Level +24dBu Input Type XLR Balanced Inputs and Euroblock Links (+ optional Expansion Module) Input Sensitivity +4dBu Input Impedance 10kOhm Output Resistance 13mOhm Front Controls Volume Adjust, 80Hz HPF Enable, 100Hz LPF Enable, Limiter Enable, Auto-Standby Enable) Indicators (LEDs) Blue/Orange Active/ Standby Orange Protection Green Signal Detection Orange/Red Limiter/Clip Cooling Fan cooled, temperature Dependent. Preferred Brands – Quest / Audio Focus / Mayer Sound / Bose.

10 + 2 Channel Analog Mixer 16 mono channels 16 internal time-delay effects Neutrik mic XLR&Neutrik 1/4 inch jacks Channel insert Super wide gain ‘DuoPre’ mic line input 3 band EQ with MusiQ 2 pre-fade Aux sends; 1 post-fade Aux send; 1 internal FX send Illuminated mute Sound image pan Illuminated PFL & peak warning indicator ALPS 100mm faders 4 stereo channels with 2-band EQ and inputs for extra sources Stereo returns & playback All inputs with level control 12 bar meters Mono/stereo function on auxes 1&2 Monitor output section Alt stereo output source Configurable USB stereo audio in/out Preferred Brands – Allen & Heath / Audio craft / Equipson / Bose/ Mayersound/Audio Focus

Hand Held wired Economy Range Cardiode Microphones Dynamic microphone element Cardioid polar pattern Balanced, low impedance (600 ohms) Output level of -52dBV/Pa (2.5mV) Frequency response of 50 to 15,000 Hz On/off slide switch XLR male output connector Weight of 244 grams with dent-resistant ball grill. Preferred Brands – Shure / Equipson / Bose/Mayersound/ Audio Focus/Sennheizer

Hand Held Dynamic wired Microphones for Speaking and singing. Type Dynamic (moving coil) Frequency Response 70 to 15,000 Hz Polar Pattern Cardioid Output Impedance 600 Ω Sensitivity at 1 kHz, open circuit voltage -53.5 dBV/Pa¹ (2.10 mV) Polarity Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3 Weight 300 g (10.58 oz.) Switch On/Off Switch Connector Three-pin professional audio (XLR), male

SHURE Combo Wireless UHF Microphone system, SVX288IN/PG-58 (consisting 2 nos. Hand Held wireless microphones working on a single receiver) • Available Frequencies: between 794 –806 MHz • Operating Range: LO power mode: 18 m (60 ft.)* HI power mode: 75 m (250 ft.)* * under typical conditions • Audio Frequency Response: 50 Hz – 15 kHz • Transmitter RF Output Power: LO power mode: 1 mW maximum HI power mode: 10 mW maximum • Audio Output Connector: XLR balanced and ¼" unbalanced • Maximum Output Level: -19 dBV (XLR), -5 dBV (1/4”) (R25 - Band for Thailand Regulation) (ref. +/-33kHz deviation with 1 kHz tone) • Battery Life: Up to 10 hours with 2 AA batteries • Dynamic Range: >90dB, A-weighted • System Distortion:

Cables, Mic. Stands, Speaker brackets, speaker cables, Interconnecting Cables, Microphone cables, storing and operating rack, clamps and other allied items.

System Installation and Commissioning charges.

Supplying, Installation, Testing & Commissioning of Manual Hand Pulling Curtain, curtain Mechanism Left to right with system, Horizontal sliding arrangement complete with track, brackets, sliding arrangement & manual operation complete with runner, master runner etcetc, size 32’ x 18’ (576 sq. ft)

Supplying, Installation, Testing & Commissioning of front frill with required accessories like cotton tape, cotton laces, Tussels with satin crush cloth of branded make shade and colour, including stitching 27’ x 3’

Supplying, Installation, Testing & Commissioning of Upper Sky – Black glazed cotton double gathered cloth curtain including arrangement of frill bar made of 32mm synthetic enamel paint finish MS pipe hanging steel wire rope 27’ x 3’

Supplying, Installation, Testing & Commissioning of Back wall covering (stage / dias), with alumunium panel with 6mm ply and cloth stitching 56’ x 17’6”

Proscenium: Providing, fitting & fixing side proscenium by made of MS Frame. The front fascia of the proscenium to be covered with 6mm BWP ply.Finally the front facia of the proscenium to be covered with 4mm thick natural teak venerred ply to be pasted on 6mm ply with adhesive in a decorative way.completed with melamine polish of approved colour. Entire work to be done as per specification and direction of E.I.C., size 19 ft 6 inch x 2ft

Supplying, Installation, Testing & Commissioning of Side wings of size 19 ft x3 ft, made up of wooden frame, infilled by Ply Boards of 6mm, covered with enameled paint / cloth, rotable.-

Stage lighting system with latest type Par Can and PAR 64 lamp Lights (12 nos), Power pack 12kW per channel 2Kw 6 pack DMX (O1 no); LCD 0602 DMX Light Mixer with controller (01 no), Metal lights facing towards the front of the stage (O2 nos); DMX Controller, XLR jack to Jacks, soltwares for DMX controllers, Microphone cables, bits, 1.5 sqmm wires, flexcible pipes. 1.5 single core cable and DMX cable etc., Clamps for fixing Lights etc., Preferred Brand – GOBO / SATAN / GIA / STAN.

System Installation, Commissioning, Programming charges for all the above mentioned Stage Craft and Lighting system.

Providing and fixing Roller Blind as per approved material (VISTA LEVELLOR) including all fittings and labour, complete job.

Providing, Supplying and installing Potable water purification system with inbuilt water cooler & RO system with stainless steel (304G) 120 ltrs water storage capacty & 2 tap, fully automatic, including all complete. (Brand; Blue Star (NST80120B)/ AQUAGUARD Equivalent)

Providing and fixing C.P. brass concealed Stop valve of standard design and of approved make conforming to IS:8931. - 20 mm nominal bore. (Approved brand - ESSCO/ Jaquar/ Equivalent)

Supplying and fixing RJ-45 jack with box cover plate etc as required. (Approved Make - )

Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)

Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)

Providing and fixing 25 / 15 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)

Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.

Supplying and fixing of Air release Valve / Drain Valve, as per required all complete job.

Supplying and fixing of Pressure Gauge Assemble with Gate/Ball Valve, as per required all complete job.

Supplying and fixing of Terrace Pump as per required all complete job.

Supplying and fixing of MS Structure support for piping, as per design and all complete job.

Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)

FURNITURE

SR. EXECUTIVE TABLE:- Supplying and placing of Executive Table of Three layerprelaminated particle board(Wood Product) ofgrade II type II of IS 12823/Latest 1500 millimeter700 millimeter 725 millimeter . (DWS/34752)

CAFETERIA CHAIR:- Supplying and placing of Nilkamal Restaurant / Cafeteria Chair with frame of SS 304 and Plastic moulded seat. Chair Armrest Without. Type of seat-Plastic moulded. Seat Cushion-Without, Back Rest Cushion-Without, Upholstery- N.A, Material of frame-SS 304, Chair height (overall) ±10mm-900mm, Backrest width ±10mm-450, Width of seat ±10mm- 450, Depth of seat in mm (+/- 10 mm)-525, Height of seat in mm (+/- 5 mm)- 450, Seat Finish- Injection moulded high impact strength polypropylene polymer compound with indoor grade UV resistance.

2 SEATER SOFA:- Supplying and placing of Total Number of Seats in the Sofa Set 2. Type of Sofa and Backrest Seat and Backrest are permanently fixed with the frame Structure. Frame Covering Fully Upholstered. Backrest Cushion Material Foam. Density of Cushion of Backrest Material (Kg/Cubic M)40. Covering Material for Seat and Backrest Leatherite. Frame Structure Material and size (±1 mm) Any other wood of minimum 25 mm thickness. Seat Cushion Material Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M)40. Type of Spring in the Base / Seating No Spring in the Base

CENTER TABLE:- Supplying and placing of Center Table,Material & Subtype Solid Wood - Beech Wood Frame Material-Solid Wood Leg Material-Solid Wood Finish-Matte Colour & Colour Family Brown - Walnut Dimension-(W)1130mm X (D)630mm X (H)410mm,The product must be from a Manufacturer having ISO 9001,ISO 14001,,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX CERTIFICATE. MAKE ..WARRANTY-5YEARS.MODEL NO-HOPPER/CT

REGULAR OFFICE TABLE WITH SIDE UNIT:- Supplying and placing of Executive Table of prelaminated MDF board 1500 millimeter 600 millimeter 750 millimeter (DWS/34723)

OFFICE CHAIR:- Supplying and placing of Revolving Chair With Arm Synchronic tilt mechanism. (70008/MB/STANDARD)

CHAIRS ( FOR COMPUTERS):- Supplying and placing of GODREJ INTERIO Revolving Chair With Arm Centre pivot mechanism GODREJ INTERIO (Godrej Interio Oxbo MID BACK CHAIR)

VISITORS CHAIR, CHAIR FOR A.V. ROOM IN LIBRARY, SEMINAR HALL AND CHAIR FOR LIBRARY READING TABLE:- Supplying and placing of DURIAN Non-Revolving and Non-Tilting chair with Armrest DURIAN (ANJIS/32002)

MULTIPURPOSE TABLE:- Supplying and placing of Anand steel Rectangular Only two leg members widthwiseand one leg member to adjoining each other - with 100 mmground clearance Classroom Tables Anand steel

WORKSTATION:- Supplying and placing of DURIAN MODULAR TABLE L X D & H 1200 millimeter X 600 millimeter 750 millimeter. Mode of Supply of modular table Knocked Down to be assembled at consignee site by consignee himself. Storage Provided- one side, Number of storage unit- triple storage, Table Top material and thickness ±3mm- 25mm thickness Flat single layer MDF board of Grade SBG II of IS 12406 Latest, Gable end and modesty panel material and thickness- 18 mm thickness three layers pre?laminated Particle boards (Wood Product) of grade II Type III of IS 12823 Latest, Length of Table Top ±10(mm)- 1200 millimeter, Depth of Table Top±10(mm) -600 millimeter, Height of Table Top 10(mm) - 750 millimeter, Warranty period in number of years-5

ALMIRAH:- Supplying and placing of Almirah Steel shelving cabinets (GARNER)

COMPUTER TABLE (COMPUTER LAB AND DIGITAL LIBRARY):- Supplying and placing of DURIAN Modular Work Stations with Four Seater Rectangular Cluster with Straight Line Side by Side Sitting

BAGGAGE RACK:- Supplying and placing of DURIAN 900 mm wide 2000 mm high Metal Shelving Racks DURIAN (Galvin)

READING TABLE (LIBRARY):- Supplying and placing of DURIAN Modular Work Stations with Double Seater Rectangular shape Cluster with Side By Side sitting

NOTICE BOARD:- Supplying and placing of NAVNEET ENTERPRISE Portrait/ Landscape Not applicable Fabric Pin Up Notice Boards NAVNEET ENTERPRISE (Fabric Pin Up Notice Boards 3 X 6 FT GREEN)

PODIUM:- Supplying and placing of DURIAN Wooden Podium design Gable end and modesty panel and top material MDF board of grade SBG II of IS 12406/Latest

CLASSROOM DESK:- Supplying and placing of GODREJ INTERIO Two seater classroom desking. (GODREJ INTERIO GENII 2 SEATER SM6)

WAITING CHAIR:- Supplying and placing of DURIAN 3 Seater Public Place Seating Chair of mild steel with arm and backrest WITHOUT CUSHION DURIAN (nixon 3 seater MS)

TEACHER TABLE:- Supplying and placing of GODREJ INTERIO Modular Work Stations with Single Seater Rectangular Cluster GODREJ INTERIO (GODREJ INTERIO UPBEAT RECTA 1800W x 600D)

CONFERENCE TABLE:- Supplying and placing of 14 SEATER oval MEETING TABLE with table top of Three Layer Prelaminated Particle Boards Of Grade-II Type-II Of IS:12823/Latest (DWS/34763 Size:- 6000mm(L)x 1200mm(D)x 750mm(H))

WHITE BOARD:- Supplying and placing of Writing Board (PMW 4x10 Non-Magnetic)

AUDITORIUM CHAIRS:- Supplying and placing of DURIAN AUDITARIUM CHAIR 450 millimeter 440mm seat with auto tip up mechanism with push back feature

LOW HEIGHT STORAGE:- Supplying and placing of DURIAN Wooden Almirah, Height 750 SI Marked, three layer Prelaminated particle Board conforming to Grade II Type III of IS 12823/2013 laminated with 0.6-0.8 mm thick lamination conforming to IS 2046/1995 and balancing lamination of 0.5 mm thick on the back side

6 SEATER DINING TABLE (CAFETERIA):- Supplying and placing of GODREJ INTERIO Powder Coated MS 6 Seater Restaurant Table. Shape of Table-Rectangular, Seating Capacity-6, Material of top, Medium density fiber board, Material of understructure, Powder Coated MS, Material of top finish. Polyurethane, Length of table ±10mm (Diameter in case of Round) 1600 mm, Depth of table ±10mm- 1100 mm, Thickness of top in mm (+/- 5%)-25 mm, Warranty period in number of years-1-year

LIBRARY PLUS SHAPE READING TABLE:- Supplying and placing of DURIAN Modular Work Stations with Four Seater Plus Shape Cluster with Curvilenear Top. Frame material for work station- Powder coated CRCA hollow system. Work top support material-Gable end made of prelaminated particle board.Material of table top -Prelaminated MDF board conorming to IS 14587/Latest. Table top finish material- Prelaminated

BOOK STACK- OPEN FROM FRONT:- Supplying and placing of DURIAN 900 mm wide 1800 mm high Metal Shelving Racks. Shelves Material 0.9 mm Thick MS Sheet Conforming to Commercial Quality CR-1, Grade 340 of IS 513

MAGAZINE RACK:- Supplying and placing of DEVENT COLLECTION Free-standing and Wall Mounted Magazine & Newspaper Rack Already Assembled. Length=900 millimeter. Width= 400 millimeter. Height=1100 millimeter

LECTURE HALL DESK (3 SITTING):- Supplying and placing of delite hi-tech THREE SEATER Class Room Desking / SeatingINTEGRATED DESK CUM SEATING delite hi-tech (DAS-8509)

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

V.R.F. A.C. WORK

GROUP "A"

Design, Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Volume air cooled Outdoor units with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 49°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. MS/GI powder coated stand with vibration isolation pads. The unit should have refrigerant-cooled PCB for better life of system.Compressor motor should have more than 4 poles.The ODU shall have low noise condenser fans with external static pressure of the outdoor unit shall be more then 75 Pa to avoid hot air recirculation, auto address setting, auto check function for connection error and complete with indoor and outdoor units with individual controller and with fittings etc. ODU having 100% inverter OEM make advanced hermetically sealed type compressor including following details :- (Note - All design & drawing should be submitted for approval by Architect), approved Brand - (Hitachi/ Daikin/ Samsung)

Norminal Cooling Capacities are based on Indoor Temperature: 27 °C DB, 19 °C WB, Outdoor Termperature: 35 °C DB, 24 °C WB, Equivalent refrigerant Piping:7.5m. Laveel differences: 0m

Sound Pressure was acquired in a deadroom. Thus, actualnoise lavelmay be different depending on the installation conditions.

DSI( Dual Smart Inverter) System, High effciency, Smart Management, Fiexible Installation, Comfortable and reliable operation

Out Door Unit- Top Discharge as per required

20 HP HEAT PUMP

Model 20HP,cooling 1 (56.0kw),cooling 190960.0btu/h),Heating 1 63.0Kwcooling 1 (10.68kw) 214830.0btu/h) , cooling 1(12.18)cooling 1(19.6 Heating 1 21.3(kw) ERR(nominal cooling 4.60),External Static pressure (110pa), liquid pipe (15.88mm), gas pipe (28.58mm), installtion max lanth (mm 220,110) transmission cable (0.75mm) Refrigerant type (R410A), Factory charing (10.5),Sound pressure (db(a)2) 61) net dimensions (WxHxD)(mm1,295*1,695*765) cooling(*C-5-53)

VRF Indoor Unit, as per design.

6.4 TR AM224JNHFKH/EU( 8HP)

Model HSP Duct 6 TR, Cooling (18.0kw), 61400btu heating(20.0kw), heating(68240btu/h), Cooling 10(0.34kw), heating 2(0.340kw), Cooling1 (1.9amp), heating2(1.9amp), air flow rate (high/mid/low/) (cfm2048/1765/1518), liquid pipe (9.52mm), gas pipe(19.05mm), drainpipe(vp25(od25,jd20), power source wire (1.5-2.5),transmission cable (075-1.5), refrigerant (R410A), control methed (eev included), sound pressure (high/mid/low)(db(a)43/39/35),net dimensions(wxhxd)(mm82.5), net dimensions (wxhxd)(mm 1350*450*910),drain pipe (Built-in), Air filter (Aviailable)

Y-Joint

Cord less remote

GROUP "B" Low Site Part.

As Per Design

Lowside: Installation, testing and comissioning of the VRF system VRF Outdoor Installation with Proper Vibration insulation , testing & commissioning of the system with all complete job with following requirements -40 HP

VRF Copper piping, as required

Suction Ling wiith closed cell nitrile rubber & necessary support, as required

Liquid Ling wiith closed cell nitrile rubber & necessary support, as required

Refnet joint installation, as required

Supplying, Installation, Testing and Commissioning of 2C X 0.75 Sqmm Copper shilded communication cable as per design.

Supplying, Installation, Testing and Commissioning Of PVC Drain Piping of follwing dia. and required qty with support

25mm Dia

40mm dia

Supplying, Installation, Testing and Commissioning Of GI Ducting of follwing gauge with required support (size as per design)

9mm thick closed cell nitrile rubber thermal insulation with required adhesive

Duct Accoustic insulation with open cell nitrile rubber

Supplying, Installation, Testing and Commissioning of Supply & Return air Grill/Diffusers with VCD

Canvas Connection

Extra Refrigerant charging with proper vaccumising system

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

TRANSFORMER

Supplying, Installation, Testing & Commissioning outdoor type copper wound transformer continuosly rated for 3ph 50Hz at full load and temp.rise not exceeding 450 c by thermometer in oil and 500c by the resistance in winding after continuous run at full load rating ,the transformer should have oil unmersed winding having vactor group DY11 HT side connected in delta and LT sideconnected in star with neutral brought out connected to provide separate earthing .The transformer shall have power terminal arrangenent bushing / cable end box on HT side and cable end box on LT side 2 nos channels with stoppers shall be provided and fix on the provided plinth for mounting the transformer .The transformer should have following standard fitting.Transformer shall be latest manufacturing standards as per amended IS specification and the load & No load losses shall be limited to the values given below or as per IS 2026 or norms issued by SEB which ever are lower. APPROVED BRAND - ARNAV POWERTECH/ AAKASH TRANSFORMER/ EQUIVALENT.

Oil conservator with filling hole with cap and plain oil level gauge.

Silica gel dehydrating breather charged with silica gel

oil drain valve

Lifting eyes / hooks

Two earthing terminals

Digram and rating plate

Air vent

Explosion vent

100 mm dia thermo meter with thermometer pocket

Four bi directional plain rollar

Power transformer 11000/433V with off load tap changer -12.5% to +2.5% in steps of 2.5% per BIS leveel-2

200KVA (No load loss 500w and load loss 3000w)

LAB FURNITURE

CHEMISTRY LAB

Island bench ,dimension W 1200mm x L 4800mm x H 900mm Granite Top: Granite with half round nosing, acid resistant, alkali-resistant = W 1200mm x L 4800mm, 18mm±2mm thick, black Interior & Exterior will be provided with powder-coated finish.(50-70Microns) Material of Construction for Work Bench:20G thick CRCA Sheet. Over all Dimension of Table: W 1200mm x L 4800mm x H 900mm 1 Drawer and 2 Shutter Cabinet: 600mm L=04 Nos Leg Space panel of 600(L)X750(H)=12 Nos Electric Race way: 16/6 amp switch and socket Anchor Make or equivalent = 08 Pair or more as required Sink of SS304/PP 450*550mm, Work mounted three way water tap with swan neck spout = 04 Nos Two Tier Reagent Rack = 1500(H)X900(L)X300(D) = 02 Nos D Frame Structure of 1200mm x L 4800mm x H 900mm, Construction of Square Pipe Structure of 60X30X1mm Exterior will be provided with powder-coated finish.(50-70Microns) With Leg of = 05 Nos of D=1200 and H=900. (APPROVED manufacturer - Relicon Technologies/ Sanvi Enterprises/ Equivalent)

L shaped bench ,dimension {W 650mm x L (3600mm + 1500mm) x H 900mm} Granite Top: Granite with half round nosing, acid resistant, alkali-resistant = {W 650mm x L (3600mm + 1500mm)} 18mm±2mm thick, black Interior & Exterior will be provided with powder-coated finish.(50-70Microns) Material of Construction for Work Bench:20G thick CRCA Sheet. Over all Dimension of Table: {W 650mm x L (3600mm + 1500mm) x H 900mm} 1 Drawer and 2 Shutter Cabinet: 600mm L= 02 Nos 2 Shutter Sink Cabinet : 600mm L= 01 Nos Foot Space=600mm L=04 Nos Electric Race way: 16/6 amp switch and socket Anchor Make or equivalent = 08 Pair Sink of SS304/PP 450*550mm, Work mounted three way water tap with swan neck spout = 01 Back Panel : 600mm L=08 Nos D Frame Structure of 600mm x L 3600+1500mm x H 900mm, Construction of Square Pipe Structure of 60X30X1mm Exterior will be provided with powder-coated finish.(50-70Microns) With Leg of = 07 Nos of D=600 and H=900

Revolving Stool Mechanical Height Adjustable + Back Hi Base, SS (304g) Frame with castor wheel

PHYSICS LAB

Supplying & Installation of Island bench ,dimension W 1200mm x L 4800mm x H 900mm Granite Top: Granite with half round nosing, acid resistant, alkali-resistant = W 1200mm x L 4800mm, 18mm±2mm thick, black Interior & Exterior will be provided with powder-coated finish.(50-70Microns) Material of Construction for Work Bench:20G thick CRCA Sheet. Over all Dimension of Table: W 1200mm x L 4800mm x H 900mm 1 Drawer and 2 Shutter Cabinet: 600mm L=04 Nos Leg Space panel of 600(L)X750(H)=12 Nos Electric Race way: 16/6 amp switch and socket Anchor Make or equivalent = 08 Pair or more as required Sink of SS304/PP 450*550mm, Work mounted three way water tap with swan neck spout = 04 Nos Two Tier Reagent Rack = 1500(H)X900(L)X300(D) = 02 Nos D Frame Structure of 1200mm x L 4800mm x H 900mm, Construction of Square Pipe Structure of 60X30X1mm Exterior will be provided with powder-coated finish.(50-70Microns) With Leg of = 05 Nos of D=1200 and H=900

Supplying & Installation of L shaped bench ,dimension {W 650mm x L (3600mm + 1500mm) x H 900mm} Granite Top: Granite with half round nosing, acid resistant, alkali-resistant = {W 650mm x L (3600mm + 1500mm)} 18mm±2mm thick, black Interior & Exterior will be provided with powder-coated finish.(50-70Microns) Material of Construction for Work Bench:20G thick CRCA Sheet. Over all Dimension of Table: {W 650mm x L (3600mm + 1500mm) x H 900mm} 1 Drawer and 2 Shutter Cabinet: 600mm L= 02 Nos 2 Shutter Sink Cabinet : 600mm L= 01 Nos Foot Space=600mm L=04 Nos Electric Race way: 16/6 amp switch and socket Anchor Make or equivalent = 08 Pair Sink of SS304/PP 450*550mm, Work mounted three way water tap with swan neck spout = 01 Back Panel : 600mm L=08 Nos D Frame Structure of 600mm x L 3600+1500mm x H 900mm, Construction of Square Pipe Structure of 60X30X1mm Exterior will be provided with powder-coated finish.(50-70Microns) With Leg of = 07 Nos of D=600 and H=900, (APPROVED manufacturer - Relicon Technologies/ Sanvi Enterprises/ Equivalent)

Supplying & Installation of Revolving Stool Mechanical Height Adjustable + Back Hi Base, SS Frame with castor wheel. (APPROVED manufacturer - Relicon Technologies/ Sanvi Enterprises/ Equivalent)

BOTANY LAB

Supplying & Installation of Island bench ,dimension W 1200mm x L 4800mm x H 900mm Granite Top: Granite with half round nosing, acid resistant, alkali-resistant = W 1200mm x L 4800mm, 18mm±2mm thick, black Interior & Exterior will be provided with powder-coated finish.(50-70Microns) Material of Construction for Work Bench:20G thick CRCA Sheet. Over all Dimension of Table: W 1200mm x L 4800mm x H 900mm 1 Drawer and 2 Shutter Cabinet: 600mm L=04 Nos Leg Space panel of 600(L)X750(H)=12 Nos Electric Race way: 16/6 amp switch and socket Anchor Make or equivalent = 10 Pair or more as required D Frame Structure of 1200mm x L 4800mm x H 900mm, Construction of Square Pipe Structure of 60X30X1mm Exterior will be provided with powder-coated finish.(50-70Microns) With Leg of = 05 Nos of D=1200 and H=900

Supplying & Installation of L shaped bench ,dimension {W 650mm x L (3600mm + 1500mm) x H 900mm} Granite Top: Granite with half round nosing, acid resistant, alkali-resistant = {W 650mm x L (3600mm + 1500mm)} 18mm±2mm thick, black Interior & Exterior will be provided with powder-coated finish.(50-70Microns) Material of Construction for Work Bench:20G thick CRCA Sheet. Over all Dimension of Table: {W 650mm x L (3600mm + 1500mm) x H 900mm} 1 Drawer and 2 Shutter Cabinet: 600mm L= 02 Nos 2 Shutter Sink Cabinet : 600mm L= 01 Nos Foot Space=600mm L=04 Nos Electric Race way: 16/6 amp switch and socket Anchor Make or equivalent = 08 Pair Back Panel : 600mm L=08 Nos D Frame Structure of 600mm x L 3600+1500mm x H 900mm, Construction of Square Pipe Structure of 60X30X1mm Exterior will be provided with powder-coated finish.(50-70Microns) With Leg of = 07 Nos of D=600 and H=900

Supplying & Installation of Revolving Stool Mechanical Height Adjustable + Back Hi Base, SS Frame with castor wheel, As per Approved Sample.

ZOOLOGY LAB

Island bench ,dimension W 1200mm x L 4800mm x H 900mm Granite Top: Granite with half round nosing, acid resistant, alkali-resistant = W 1200mm x L 4800mm, 18mm±2mm thick, black Interior & Exterior will be provided with powder-coated finish.(50-70Microns) Material of Construction for Work Bench:20G thick CRCA Sheet. Over all Dimension of Table: W 1200mm x L 4800mm x H 900mm 1 Drawer and 2 Shutter Cabinet: 600mm L=04 Nos Leg Space panel of 600(L)X750(H)=12 Nos Electric Race way: 16/6 amp switch and socket Anchor Make or equivalent = 10 Pair or more as required D Frame Structure of 1200mm x L 4800mm x H 900mm, Construction of Square Pipe Structure of 60X30X1mm Exterior will be provided with powder-coated finish.(50-70Microns) With Leg of = 05 Nos of D=1200 and H=900

Supplying & Installation of L shaped bench ,dimension {W 650mm x L (3600mm + 1500mm) x H 900mm} Set 01.00 2,59,670.00 2,59,670.00 Granite Top: Granite with half round nosing, acid resistant, alkali-resistant = {W 650mm x L (3600mm + 1500mm)} 18mm±2mm thick, black Interior & Exterior will be provided with powder-coated finish.(50-70Microns) Material of Construction for Work Bench:20G thick CRCA Sheet. Over all Dimension of Table: {W 650mm x L (3600mm + 1500mm) x H 900mm} 1 Drawer and 2 Shutter Cabinet: 600mm L= 02 Nos 2 Shutter Sink Cabinet : 600mm L= 01 Nos Foot Space=600mm L=04 Nos Electric Race way: 16/6 amp switch and socket Anchor Make or equivalent = 08 Pair Back Panel : 600mm L=08 Nos D Frame Structure of 600mm x L 3600+1500mm x H 900mm, Construction of Square Pipe Structure of 60X30X1mm Exterior will be provided with powder-coated finish.(50-70Microns) With Leg of = 07 Nos of D=600 and H=900

Supplying & Installation of Revolving Stool Mechanical Height Adjustable + Back Hi Base, SS Frame with castor wheel

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

100 KLD ETP PLANT EFFULUENT TREATMENT PLANT

Design, supplying, installing, testing & commissioning of Effuluent Treatment Plant. The Effuluent Treatement shall be based on MBBR technology. The nature of effluent is domestic Waste water from wash areas which shall be discharged into the ETP. Plant. The scope shall include design and execution of all electrical, mechanical, plumbing, processing, ancillary equipments and works etc required to complete the package along with getting approval from the state pollution control board, other statutory bodies as well as from the design consultant. The scope also includes the design of Electro mechanical elements. Execution of civil works shall be in the scope of the Civil contractor as per the design of the ETP vendor. Design to take consideration as given below

Nature of effluent - Effuluent from Waste areas

Daily average flow - 100 KLD / Per Day

PH : 2.93PPM Total Suspended Solids : 75 ppm Biological Oxygen demand : 1008 ppm Chemical Oxygen demand : 2279.4 ppm Oil & Grease : 9.5 ppm

Effluent discharge standard after treatment :

PH : 6-7.5PPM Biological Oxygen demand : < 50 ppm Chemical Oxygen demand : <200 ppm

LIST OF MECHANICAL EQUPMENT-

01 Bar Screen 0.5m x 0.5m 2nos SS/MS

02 Defused Aerating system 1 lot PVC /PP Pipe, Make - ASTRAL /SUPREME/FINOLX

03 Valves & inter connector pipe work 1 lot PVC /PP Pipe, Make - ASTRAL /SUPREME/FINOLX

04 Tube modules 1 lot PP

05 Accessories for primary and secondary clarifier 1 lot MS/PVC Pipe, Make - TATA/JINDAL

06 Alum solution tank with agitator 100 ltrs (FRP/eqv) 1 No., Make - TATA/ PAINTAIR/EQV

07 Lime solution tank with agitator 100 ltrs (FRP/eqv) 1 No., Make - TATA/ PAINTAIR/EQV

08 Poly electrolyte tank with agitator 100 ltrs (FRP/eqv) 1 No., Make - V

09 Blower 5 HP 2 Nos. (1W+1S)., Make - A1/ AKASH/EQV

10 Dosing Pump 100 L/Hr, 5Kg/cm2(Metering pump)3 Nos., Make - E-DOSE/EQV

11 Dosing pump 5 L/Hr, 5Kg/cm2 1 No., Make - E-DOSE/EQV, Make - KIRLOSKAR/KSB/WILLO

12 Effluent transfer pump capacity 4m3/hr 2Nos (1W+1S).

13 Slag recirculation pump 1 No (1W), Make - KIRLOSKAR/KSB/WILLO

14 Filter feed pump capacity 4m3/hr 2 Nos. (1W+1S)., Make - KIRLOSKAR/KSB/WILLO

15 MBBR Media 1 Lot.

16 Two stage Filters (FRP vessels) 2 Nos.(DMF/ ACF), Make - TATA/ PAINTAIR/EQV

Contractor shall ensure submission of detailed GA drawings (Plan & Section), P&I diagram, Schematic flow diagram for the above mentioned components and additional components such as inserts, puddle flanges, vent pipes etc. if so required for the complete work.

LIST OF INSTRUMENTS

1. Pressure gauges 2 nos./ All Pumps, Make - H.GURU/EQV

2. Float switch -3 Nos for all pumps, Make - DANFOSS/EQV

3. Rota meter

LIST OF ELECTRICAL ITEMS

01 Control panel with automation system 1no., Make - L&T/SCHNEIDER/EQV

02 Power cable, Make - POLYCAB/HAVELLS/ EQV

BAR SCREEN

Main Frame - MS Flats, 25 wide x 5 thick min.

Bars - SS round bars 4 mm dia.or as per Vendor

Bar Spacing - 8 mm or as per Vendor

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Accessories - Anchor Fasteners for fittings, matching comber with long handle (MS) for removing floating solids.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Float switch with Automatic Operation

All pumps will be operated with float switch with Automatic Operation connected with the control panel

MS hot dip galvanized puddle flanges as required to be provided (in the structural slab and wall) of various diameters. Puddle flanges shall be provided for all the structural component of the ETP.

Note: Supply and Installation of Puddle Flanges shall be done by the Civil contractor. However, all design drawings, specifications, technical data and site supervision shall be done by the ETP vendor

Plastic manhole step or foot rest 30mm reinforcing bar. of the foot in various tanks/ components of the ETP for the purpose of accessability. The installation of the foot rest shall be done by the civil contractor as per civil GA drawing

Note: Supply and Installation of Foot rests shall be done by the Civil contractor. However, all design drawings, specifications, technical data and site supervision shall be done by the STP vendor

Supply of vent pipes of 100 mm dia UPVC pipe with mosquito proof grating suitable for the ventilation purpose of the various tanks., Make - ASTRAL/SUPREME/FINOLEX

Note: Supply of Vent Pipes shall be in scope of ETP vendor. Installation shall be done by the Civil contractor under the supervision of the ETP vendor

DEFUSED AERATING SYSTEM

Supply installation of Defused Aerating System.

Supply installation of PVC, EPVC, GI pipe fitting including valves, fittings with inter connecting piping work.

Air diffusion system

Air piping shall comprise of pipes droppers/ laterals with MS (epoxy coated) Header and all drop pipes in PVC or GI complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good.

EQT - 1 No., AERATION TANK - 1 No., MBBR Tank - 2 Nos.

Non clog type air dispersion system capable of handling 3-5 cfm of air with oxygen transfer efficiency of 3-4% per/meter water depth. Air dispersion grid in SS304 shall be assembled in modular form so that they can be replaced / repaired

Fine bubble diffusers in SS304 (Capacity 4 m3/hr or as per Vendor)

For EQT - 1 No., SHT - 1 No., MBBR Tanks - 2 Nos.

Note : Air dispersion system shall be provided for Equalisation Tank, Sludge holding Tank and MBBR Tank.

Providing and fixing all piping (as described below) and isolation control valves for making the system complete.

GI/PVC piping :Pumped effluent & tank overflow pipe line

MS Epoxy : Non Submerged Air piping

GI/PVC piping :Pumped effluent & tank overflow pipe line

TUBE MODULES

Supply installation of Tube Modules.

ACCESSORIES FOR PRIMARY AND SECONDARY CLARIFIER

Supply installation of Accessories like MS and PVC pipe fitting, valves etc.

ALUM SOLUTION TANK WITH AGITATOR

Supply installation of 100 ltrs FRP Tank with Agitator

LIME SOLUTION TANK WITH AGITATOR

Supply & installation of 100 ltrs FRP Tank with Agitator

POLY ELECTROLYTE TANK WITH AGITATOR

Supply & installation of 100 ltrs FRP Tank with Agitator

BLOWER TWINLUBE

Supply & installation of twin Blower 1 w /1 std by

DOSING PUMP , Make - E-DOSE /EQV

Supply & installation of Dosing Pump

Providing and fixing chemical dosing system with all accessories, suitable to doze chemical soluktion upto 1 ppm doze (of Sodium Hypo-chloride solution) to a filtered water flow of 4000 lph. against a pressure of 1.5 kg/cm2 complete with FRP moulded solution holding tank of min. 100 litre with all standard accessories & structural arrangement including suitable foundation bolts & other accessories etc.complete as required and as specified.

System : Metering Type

Capacity : 0-5 LPH

Feed Solution : Hypochlorite

Conc. Of Solution : 0.1

MOC and Capacity of Tank : HDPE - 100 Litres

EFFLUENT TRANSFER PUMP, Make - KIRLOSKAR/KSB/WILLO

Raw Sewage Lifting Pumps, Make - KIRLOSKAR/KSB/WILLO

Providing and fixing compact monoblock dry motor submersible pumps of suitable rating, with non-clog free flow open CI impeller, CI casing and SS Shaft, suitable for operation on 415 volts ± 10% , 3 Phase motor, 50Hz, A.C supply, speed 2900 RPM, including oil chamber, guide wire for lifting & lowering of pump, M.S. galvanized lifting chain, duck foot bend complete. The pump sets shall be supplied with required accessories & as per specification with the following :

Pump Headers and other interconnecting pipes

Complete inlet, outlet and header piping of suitable dia (velocity shall not exceed 1.5m/s) -- 1 Lot

Butterfly valve and Dual Plate NRV of appropriate dia and rating - 1 Lot

Necessary cables from pump sets to pump starter panel - 1 Lot

Discharge : 4 m3/Hr

Head : 15 m

Solid Handling : 30-35 mm

Pumps shall be operated on cyclic timing with automatic timer set

One set consist of 2 nos. of pumps - 1 working & 1 stand by (Complete set as above no. pumps including cost for valves, piping, Control Panel, Cabling, contactors, breakers, overload relay, float switch, level indicators, pressure gauges etc as required and as specified and any other additional items to make the system complete)

SLAG RECIRCULATION PUMP, Make - KIRLOSKAR/KSB/WILLO

Providing and fixing vertical multistage centrifugal clear water pump set with SS casing, SS impeller, SS-316 shaft, CI base with CED coating, complete directly coupled with TEFC induction motor of class "F" insulation, 2900 RPM, suitable for operation on 415 volts ±10%, 3 phase, 50 Hz, A.C. supply (with cartridge type mechanical seal), pressure gauges with gunmetal isolation cocks, vibration elimination pads, etc. mounted on a MS base frame bolted to cement concrete foundation complete in all respects and as per specification with the following capacities:

Capacity : - 5.0 m3/hr

Head : - 18-20 m

Note-CIP pumps can be common with item no.c

Motor Efficiency Class - IE3

Supplying, Installation, testing and commissioning of chlorine dosing system compromising of Sintex Tank with inlet/ outlet connection, piping and valves alongwith metering pump of 0-5LPH for dosing.

Supplying, Installation, testing and commissioning of CIP Dosing system compromising of Sintex Tank with inlet/ outlet connection, piping and valves alongwith metering pump of 0-5 LPH for dosing.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Supplying, Installation, testing and commissioning of CEB Dosing system compromising of Sintex Tank with inlet/ outlet connection, piping and valves alongwith metering pump of 0-5LPH for dosing.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Supply, installation & commissioning of HDPE backwash tank of 500 Litre capacity including required level controller

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Supply, installation, testing and commissioning of top discharge Stainless Steel bucket type Centrifuge of Suitable Capacity suitable for 100 KLD ETP capacity with feed pump (Monoblock Centrifugal Self Priming Type) – 2 No. (1 working + 1 standby) with 1 No. standby stator, associated valves, pressure guage, level switches, polymer dosing tank, interconnecting piping and poly dosing system and other associated piping, valves and items as per approved P&I.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Providing & fixing on line pH meter digital type for Monitoring the online pH after Ultrafiltration. Including electrical wiring from panel to flow meter. Complete with all type of Plumbing & Electrical connections, accessories, wiring, conduits & supports complete with all respect.

At Sewage Inlet

At Raw Sewage Pump Outlet Rotameter

At Filter Feed Pump outlet Rotameter

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

FILTER FEED PUMP

Supply & installation of mono block pump with the capacity of 4m3/hr @15 meter head- 01 working & 01 stand by., Make - KIRLOSKAR/KSB/WILLO

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Providing and fixing vertical multistage centrifugal clear water pump set with CS casing, CS impeller, CS shaft, CI base with CED coating, complete directly coupled with TEFC induction motor of class "F" insulation, 2900 RPM, suitable for operation on 415 volts ±10%, 3 phase, 50 Hz, A.C. supply (with cartridge type mechanical seal), pressure gauges with gunmetal isolation cocks, vibration elimination pads, etc. mounted on a MS base frame bolted to cement concrete foundation complete in all respects and as per specification with the following capacities:

Complete inlet, outlet and header piping of suitable dia -1 LOT

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Butterfly valve and Dual Plate NRV of appropriate dia and rating - 1 Lot

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Discharge : 4 m3/Hr

Head : 15 m

No. of Pumps : 2 (1W+1S)

Motor Efficiency Class - IE3

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Operation of pump shall be based on level controller proposed to be installed in tank as per site location.

The cement concrete foundation shall be 200 mm high and 150 mm projection on all sides of M.S. base frame shall be designed by the STP Contractor and executed by the Main Civil Contractor.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

MBBR MEDIA

Supply, installation, testing and commissioning of PVC MBBR media to be installed in MBBR Tanks PRIMARY CLARIFIER AND SECONDARY CLARIFIER (2 Nos.) and PVC tube deck settling media to be installed in Secondary Settling Tank alongwith suitable sludge removal arrangement either by pumps or air lifting pumps

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Vendor to specify Surface area and flow rate

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

DMF FILTER/ MF FILTER

Dual media filter FRP vessel with multi port valves accessories and filter media 600 mm dia with height of 1800 mm flow rate @4000 LPH back wash flow rate 200 LPH operating pressure 3kg/cm2

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

The filter shall also be provided with set of internals for raw water inlet and bottom collecting system. Complete with frontal piping (heavy) and butterfly valves designed on 1.50 m / sec velocity.

ACF FILTER

Providing and fixing C.P Soap Dish of aaproved size, shape and approved brand with concealed fittings, complete job.

ELECTRICAL INSTALLATION FOR ETP, CONTROL PANEL WITH AUTOMATION SYSTEM INCLUDING CABLE TRAY WITH CABLE

Also, refer to General Notes and Specifications for Panels/ Boards

GENERAL NOTES FOR MCCB's:

ACB's & MCCB's shall be of 3P or 4P as called for in the BOQ.

Ics = Icu = 100% for the MCCB's, MPCB's & ACB's

MCCB's shall be with extended rotary handle.

Only one make of switchgear to be used in a board /panel.

All communicable meters should be looped inside the panels and this loop has to be brought to one terminal point in the panel for connectivity.

No BMS cable should be directly connected to VFD and hence these points will have to brought on to the terminal blocks inside the panel.

All energy meters shall be dual source and communicable type.

The power factor capacitors shall be of inert gas type and shall be suitable for 525 volts operation.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

IP Rating : IP54

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Incomer:

• 1 No. 63A, 3P, MCCB, 25 KA of suitable rating as per load.

• MCCB shall be with inbuilt micro-processor based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Incomer Indications:

• R,Y,B phase indication lamps

• ON/OFF, Trip indication lamps

• Indication lamps shall be LED type (63V)

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Incomer Metering:

• 1 No. combined Digital VAF meter

• Meter shall be (110V) and communicable type.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

CT for Incomer Metering :

• CT metering Class-1 accuracy CT’s (one per phase)

• CT shall be cast resin type & shall be of suitable burden (VA) & ratio.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

PT for Incomer Metering & Indication Lamps:

• 415V / √3 / 110V / √3 PT for metering and indication lamps.

• PT shall be Class-1 accuracy.

• PT shall be cast resin type.

• PT shall be of suitable burden (VA).

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Protection for Metering PT:

• TP MPCB of suitable rating & fault withstand capacity on primary side of PT.

• TP MCB of suitable rating on secondary side of PT.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Bus Bars:

• 100A, 3P, 25 KA, Aluminium Bus Bars of electrolytic grade with heat shrinkable sleeves.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

110V Control Transformer for Contactor Coils of Starters & out goings Indication lamps:

• 1 No. 415V / 55-0-55 V, cast resin control transformer.

• Transformer to be of adequate burden.

• Transformer with primary taps at ± 2.5%, ±5%, 50HZ, centre tap earthed.

• 110V control bus.

• TP MPCB of suitable rating & fault withstand capacity at Primary side & DP MCB at secondary side of control transformer.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Outgoings

DOL Starter Feeders for:

• 2 Nos. for Sludge Recirculation Pumps (1W+1S)

• 2 Nos. 3.73 KW for Filter Feed Pumps (1W+1S)

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

• 2 Nos. for Screw Pump (1W+1S)

• 2 Nos. for Air Blower (1W+1S)

Spare DOL Starter Feeders for:

• 1 Nos. 3.7 KW motor.

• 1 Nos. 5.6 KW motor.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Feeder for Sewage Sump Pump Panel / Panels (within pump room) (without starter): No. of feeders - 1

• 1 No. 3P, MCCB, 25 KA of uitable rating as per load of 4.5 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Feeder for etp Sump Pump Panel / Panels (within pump room) (without starter): No. of feeders - 1

• 1 No. 3P, MCCB, 25 KA of uitable rating as per load of 4.5 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Feeder for ETP Bypass Sump Pump Panel (without starter):

• 0 No. 3P, MCCB, 25 KA of uitable rating as per load of 11.2 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Feeder for Soft Water Transfer Pump Panels (within pump room) (without starter): No. of feeders - 1

• 1 No. 3P, MCCB, 25 KA of uitable rating as per load of 4.5 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Feeder for Flushing Water Transfer Pump Panels (within pump room) (without starter): No. of feeders - 1

• 1 No. 3P, MCCB, 25 KA of uitable rating as per load of 11.2 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Feeder for Irrigation Water Transfer Pump Panels (within pump room) (without starter): No. of feeders - 1

• 1 No. 3P, MCCB, 25 KA of uitable rating as per load of 4.5 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Spare Feeder similar to above (without starter):

• 1 No. 3P, MCCB, 25 KA of uitable rating as per load of 11.2 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

SOLAR POWER GENERATION

SOLAR POWER GENERATION WITH BATTERY POWER BACKUP AREA OF ROOF FOR SOLAR PANEL 50% AREA OF ROOF = 4800.00 S.FT, . No. OF KWA @ 1KWA PER 100 S.FT. . NO. OF KWA =48.00 KWA. . (WORK TOBE DONE THROUGH JEREDA, NOT FOR TENDER)

Add 18% GST

Add 1% Labour cess 1%

M/S RANG BAHADUR SINGH