ADDN / ALTN CUM SPECIAL REPAIRS TO JCOs/OR MD ACCN AT LOWER CAMP, CHEERBAGH AND TALWAR LINES AT DEHRADUN

Amount

SCHEDULE 'A' PART- I (BUILDING WORK INCLUDING SPECIAL WORKS)

Dismantling wall and ceiling boards, fibre or pulp, insulation etc. in insulation boards slabs, blankets any thickness incl cover fillets complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed.

Dismantling timber scantling 40 sqcm & over in section framed work in any position complete all as specified and directed.

All as per Srl Item No 5.00 above in fillets, rails, posts, rafters, purlins, etc. unframed work under 40 sq. cm in section complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling of brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. and rubbish off the premises complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 sqm each including taking out of holdfast & making good in CM (1:4) complete all as specified.

All as per Srl Item No 9 above but not exc 1.5 Sqm each complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide & n.exc 1.50m depth for foundation & getting out in any type of soil complete all as specified & directed.

M & L PCC 1:4:8, type D-2 (Using 40mm graded stone aggregate) as in sub base, foundation and mass concrete. etc complete all as specified and dirceted.

M & L for brick work with common burnt clay bricks built in CM 1:6 straight or curved on plan & exc 6 m mean radius with old size bricks complete all as specified and directed.

All as per Srl Item No 13 above but except bricks complete all as specified and directed.

M & L for brick work with common burnt clay bricks, in half brick thick wall built in CM 1:4 straight or curved on plan to any radius with old size bricks complete all as specified and directed.

Returning / filling trenches in soil including spreading watering, well ramming in layers n.exc 25 cm thick after laying and testing of pipe complete all as specified & directed.

Removing excavated material / surplus soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified & directed.

S & F steel work in tubular trusses including special shaped washer, plates, and tubular purlins etc. complete using ERW or induction butt welded tubes confirming to IS-1161-1979 grade St-240 complete all as specified and directed.

M & L Bands, straps, including bolts, if required hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins; knee piece inserts; similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M & L for cement concrete 1:2:4, type B1 (using 20mm graded stone aggregate) as in copings , benching, bedplates etc. including all necessary formwork etc. complete all as specified and directed.

S & F 0.50 mm thick Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any approved colour, having tensile strength of 550 Mpa as in roof, covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S & F prepainted galvalume aluminium zinc coating GI base plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof, fixed with self tapping screws as specified. Complete all as specified and directed.

Supply & fixing false ceiling of Designer ceiling tiles Ivory painted ready to use (made of high pressure steam cured 4mm thick as IS 14862) of size 595x595mm and any one of the design (Cascade or electra texture of Everest or equivalent) in true horizontal level, suspended on exposed inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and croos 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 3mm dia GI wire shall be pre-painted with polyester paint and black painted groove at centre of size 4mm depth and 4.5mm width, complete with heights complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thick (below or above ground level) including rubbish off the premises complete all as specified and directed.

M & L 25 mm thick PCC 1:2:4, type B-1 (20 mm graded stone aggregate) as in floors to receive floor finishes complete all as specified and directed.

M & L for joint free coloured ceramic tiles not less than 7 mm thick x 600 x 600mm in size, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified including 15 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

All as per Srl Item No 26 above but as in skirting including 10mm thick in CM (1:4) as in backing coat of tiles complete all as specified and directed.

M & L non-skid ceramic tiles not less than 7 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified including 15 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

M & L for Glazed ceramic coloured tiles of size 450 mm x 300 mm x not less than 7 mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile on vertical surfaces of wall including 10 mm thick rendering on brick surface in CM 1:4 complete all as specified and directed.

M & L machine cut kota stone slab (mirror polished) of size 550 mm x 550 mm and not less than 20 mm thick over and including 20 mm thick cement screed base in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete all as specified and directed.

All as per Srl item No 30 above but on vertical faces of walls as in skirting and dados including 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work including cutting of reinforcement to facilitate demolition complete all as specified and directed.

M & L for form work to soffits and sides of suspended slab, shelves and chajja etc. n exc 200 mm thick fair finished surface of concrete flat, complete all as specified and directed.

M&L for RCC 1:2:4, type B1 using 20mm graded stone aggregate (Nominal Mix) as in slabs supported on walls, shelves, chajjas etc. and similar work, complete all as specified and directed.

S & F TMT bars 10mm dia and over cut to length bent to shape required incl. cranking bending spirally for hooking and binding with and incl. MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per Srl item No 35 but 8mm dia complete all as specified and directed.

M & L not less than 16 mm thick Granite (of any type) work in jambs, pillars, cooking platform and like bedded jointed and in grey cement with admixture of pigment to match with shade of granite over and including 20 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M & L Rounding to edges of stone slabs one edge, such as in steps cooking platform, and other similar situations complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-1, (20 mm graded stone aggregate) as plinth protection finishing the surface even and smooth without using extra cement complete all as specified and directed including joint between panels & corners of plinth protection and joints filled with mix of 1 part bitumen 85/25 grade and 3 parts of sand.

M & L for preparing new steel or iron surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Taking down cement or cement lime plaster/tile work on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. complete all as specified and directed.

M & L for Complete removal of existing treatment from walls complete all as specified and directed.

M & L for Raking out joints/ pointing to brick work in wall etc built in cement mortar complete all as specified and directed.

M & L for 15mm thick rendering on other than fair faces of brick/ concrete surfaces in CM 1:6 finished even and fair complete all as specified and directed.

M & L for 15mm thick rendering on fair faces of brick/ concrete surfaces in CM 1:4 finished even and fair complete all as specified and directed.

M & L 5 mm thick rendering in CM 1:3 on ceiling/ chajjas etc finished even & smooth without using extra cement incl taking down old cement plaster complete all as specified and directed.

M & L for 2mm thick wall care putty on walls complete all as specified and directed.

M & L for Preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted over one coat of primer complete all as specified and directed.

M & L for preparing new plastered surfaces of walls ( up to triple story bldg) & applying two coats of Ist quality exterior emulsion weather coat paint over a coat of alkali resistant priming paint complete all as specified and directed.

M & L preparing new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L one coat of white wash on old decorated plastered surfaces of walls incl preparation of surfaces complete all as specified and directed.

M & L applying three coats of white wash on ceiling on newly plastered surfaces incl preparation of surfaces complete all as specified and directed.

M & L one coat of white wash on old decorated plastered surfaces of ceiling incl preparation of surfaces complete all as specified and directed.

M & L complete removal of old painted surfaces of wall with scraping, wire brushing, washing with water and preparation of surfaces ( up to triple story bldg ) & applying two coats of Ist quality exterior emulsion weather coat paint over a coat of alkali resistant priming paint complete all as specified and directed.

M & L for Taking down shutters of any description n. exc. 1 sqm each and removing from site complete all as specified and directed.

M & L for Taking down shutters of any description exc. 1 sqm and n. exc 2 sqm each and removing from site complete all as specified and directed.

S & F Pressed steel frames for doors made out of 1.25mm thick with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 125 x 60 mm, complete, all as specified.

M & L for cement concrete 1:3:6, type C0 using 12.5 mm graded stone aggaregate as in bedplates, filling in pressed steel door frames etc. including all necessary formwork etc. complete all as specified.

S & F factory made 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F factory made IInd class hard wood, 35mm thick glazed, and skeleton shutters open rebated & prepared to receive, glass, gauge etc. (without sash bars), edge of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part I, Section 8, clause 8.24(a); supplied and fitted to chowkats complete all as specified and directed.

S & F factory made second class hardwood rail and style, 35 mm thick factory made, plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S & F FRP door frame of size 100 mm X 50 mm made out of 3mm thick coloured prelaminated FRP sheet with UV grade polyester resin complete all as specified.

S & F 30 mm thick FRP door shutters with UV grade polyester resin with minimum 3 mm thick coloured prelaminated FRP sheet fixed on both sides complete all as specified and directed.

S & F Ist class hard wood (shesham) small fittings such as brackets of any type, door stoppers and like including all necessary labours, articles n exc 200 cucm each complete all as specified and directed.

Supply only butt hinges medium weight cold rolled mild steel, size 100 mm complete all as specified and directed.

All as per Srl item No 65 above but 50 mm size.

Supply and fixing mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

S & F floor door stopper of aluminium body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 140 mm and fixed to door shutters.

S & F aluminium handles fabricated type anodised 150 mm size complete all as specified and directed.

S & F aluminium anodised barrel tower bolt of extruded section 200 mm length of bolt complete all as specified and directed.

S & F in repairs aluminium anodised barrel tower bolt of extruded section 200 mm length of bolt complete all as specified and directed.

S & F stainless steel sliding door bolt (bolt type) with bright bolt of 16mm dia with and including a minimum of 6 bolts and nuts, and fixed, length of bolt 300 mm complete all as specified and directed.

S & F in repairs stainless steel sliding door bolt (bolt type) with bright bolt of 16mm dia with and including a minimum of 6 bolts and nuts, and fixed, length of bolt 300 mm complete all as specified and directed.

M & L for Resecuring or easing & adjusting without taking down shutters of any description not exc 1 Sqm each complete all as specifed an directed.

M & L for Resecuring or easing & adjusting without taking down shutters of any description exc 1 and not exc 2 Sqm each complete all as specifed an directed.

S & F 20 mm dia Stainless Steel 1 mm thick curtain rod including fancy type brackets fixed to wall and 8 Nos curtain rings per RM (minimum) complete all as specifed an directed.

M & L for Steel windows with side hung shutters (Box Type) precoated (colour coated / powder coated ) with double shutter (glazed and gauged shutter both) with frame complete all as specified and directed and shown on Drg No TD 158 sh 1/2 to 2/2). Note- Measurements shall be taken and paid compositely for frame, glazed and gauged shutters. No seperate payment shall be allowed for glazed shutter and / or gauged shutter. However, grills shall be paid seperately under respective item.

S & F steel ventilator with top side hung shutter including hinges, steel peg stay, complete all as specified and directed. (TD 88 Sh 1/17 to 17/17)

S & F steel windows or ventilators, fixed type, with glazing bars Complete all as specified and directed. (TD 88 Sh 1/17 to 17/17)

M & L for 4mm thick sheet glass, ordinary quality and glazing with oil putty / pins /spring pins and wooden beads in square not exceeding 0.5 Sqm in each pane Complete all as specified and directed.

M & L for 4 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane Complete all as specified and directed.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples Complete all as specified and directed.

M & L framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 Complete all as specified and directed.

S & F 18 mm thick plywood coated with fibre reinforced plastic (FRP) 3mm laminated on both faces (3mm +12mm+3mm) and edges to be sealed with PVC edges binding tape for cupboard shelf and shutter complete as per specifications and as directed.

S & F continuous (piano) hinges, mild steel, bright finish or electrogalvanized, width of flap 30 mm Complete all as specified and directed.

S & F 150 mm size hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws Complete all as specified and directed.

S & F 40mm dia, cupboard knobs fixed with nut, screw and washer of brass polished, bright finished Complete all as specified and directed.

S & F brass chromium plated tubular towel rail min 1mm thick 20mm dia for CBs Complete all as specified and directed.

M & L for Preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M & L for Preparation old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparing new steel or iron surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer Complete all as specified and directed.

S & F rotational moulded polyethylene water storage tanks white colour Triple layer (cylindrical vertical with closed top) 500 Ltrs capacity, hoisted and fixed in position all as specified in SSR Part I including dismantling old unserviceable water tank Complete all as specified and directed.

S & F 20mm stop valve, cast copper alloy, butterfly handle, screwed down, high pressure, screwed for iron pipe or brass ferrule and fixed Complete all as specified and directed.

M & L for Taking down steel tubing and connections, incl cleaning for refixing or removal to store, 15mm bore of pipe Complete all as specified and directed.

M & L for Taking down steel tubing and connections, incl cleaning for refixing or removal to store, 20mm bore of pipe Complete all as specified and directed.

M & L for Cutting chases in brick/stone walls, pinning in, making good to facing where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting not exceeding 10cm girth complete, all as specified and directed.

M & L Galvanised Iron tube medium grade with fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 15mm Complete all as specified and directed.

M & L Galvanised Iron tube medium grade with fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 20mm Complete all as specified and directed.

S & F 20mm dia ball valve high pressure PTMT with epoxy coated aluminium rod & high pressure plastic ball screwed for iron pipe and fixed Complete all as specified and directed.

S & F in repair vitreous china wash hand basin white flat back of size 550 mm x 400 mm, including brackets, CP washers coupling & waste pipe complete all as specified and directed

S & F in repairs vitreous china water closet Squatting Orissa pattern white size 580 mm x 440 mm, white, with 'P' or 'S' trap, front or back inlet, integral foot rest with provn of PCC, type B-1, using 20 mm grading stone agg, complete all as specified, (excluding flushing cistern and flush pipe) etc. and making good to floors in repair, Complete all as specified and directed.

S & F in repair, low level 10 ltrs capacity PVC valve less symphonic action type flushing cistern incl flush pipe fixed with inlet ball valve, float and handle, including brackets, Complete all as specified and directed.

M & L for Kitchen plate rack made of stainless steel 1mm thick with shelves of overall size 900mm x 750mm, fixed to wall, Complete all as specified and directed.

S & F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410 mm x 330 mm x 160 mm Complete all as specified and directed.

S & F 15 mm bore CP Bib taps, fancy type, long body, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and dirceted.

S & F stop valves 15mm bore concealed type chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed Complete all as specified and directed.

S & F stop valves / angle valve 15mm bore fancy type chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed Complete all as specified and directed.

S & F in repairs 15mm bore brass CP wall mixture or kitchen sink mixture with hot & cold water screwed down for iron pipe and Complete all as specified and directed.

S & F 15mm bore brass CP mixture for wash basin with hot & cold water screwed down for iron pipe and fixed Complete all as specified and directed.

S & F brass chromium plated shower rose, 125mm size, fixed Complete all as specified and directed.

S & F in repair 5.5 mm thick sheet glass shelf assembly consisted chromium plated bracket guard & railing 60 cm long fixed with screws Complete all as specified and directed.

Supply & fixed 8 mm thick sheet glass shelf corner (300x300mm size) assembly consisted chromium plated bracket guard & railing fixed with CP screws complete all as specified and directed.

S & F 15mm size PVC connection with PTMT nuts length 450mm long complete all as specified and directed.

S & F PVC, bathroom mirror cabinet of approx overall size 450 mm x 300 mm x 150 mm fixed to wall with brass screws, complete all as specified.

S & F in repair brass chromium plated towel rail 20mm dia D type 60cm long between flanges of brass chromium plated complete all as specified and directed.

Dismantling of 100mm dia cast iron drain pipes with any type of joints and taking out of trenches if required or from walls complete all as specified and directed.

All as per Srl Item No 117 above but PVC drain pipes complete all as specified and directed.

Dismantling of 75 mm dia cast iron drain pipes with any type of joints and taking out of trenches if required or from walls complete all as specified and directed.

All as per Srl Item No 119 above but PVC drain pipes complete all as specified and directed.

S & F cast iron Nahani trap 75mm dia outlet with CP grating incl jointing to waste pipe in cement concrete type B-1(1:2:4) (ISI MARKED) complete all as specified and directed.

S & F 100mm dia cast iron sanitary connection 'P' branch, with branch 375 to 450mm long (ISI MARKED) including jointing in cemen complete all as specified and directed..

S & F 100mm dia cast iron bends any radius with duck foot or heel rest (ISI MARKED) including jointing with CM 1:1 complete all as specified and directed.

All as per Srl item No 123 above but 75mm dia complete all as specified and directed.

S & F branch piece for 100mm dia CI spun pipe, single (equal or unequal) ordinary or inverted fitted with oval access doors complete all as specified and directed.

All as per Srl Item No 125 above but 75mm dia complete all as specified and directed.

S & F cast iron cowl for 75 mm bore pipe complete all as specified and directed.

S & F cast iron bend (any radius), diminishing pieces or tapers 100 mm dia complete all as specified and directed.

All as per Item No 128 above but for 75mm bore C I pipes fitted with oval access complete all as specified and directed.

S & F 100mm dia cast iron sanitary connection short connections pipe of length 300mm complete all as specified and directed..

S & F salt glazed stone ware gully traps in repairs square or rounded mouthed type P or S of size 150 x 150cm incl excavation earth work concrete in beds, surrounds kerbs etc complete all as specified and directed.

S & F 100mm dia cast iron spun pipe soil waste and vent pipes in any length with or without ears with cement joints laid in trenches or in floors (ISI MARKED) complete all as specified and directed.

All as per Srl item No 132 above but 75mm dia laid in trenches complete all as specified and directed.

S & F 100mm dia cast iron spun pipe soil waste and vent pipes in any length with or without ears with cement joints, fixed to walls including holder bats complete all as specified and directed..

All as per Srl item No 134 above but 75mm dia complete all as specified and directed..

M & L for Extra over cast iron pipe and fittings if lead joint is provided in lieu of cement joint for 100mm pipe complete all as specified and directed.

All as per Srl item No 136 above but 75mm dia bore pipe complete all as specified and directed.

M & L for excavation in post holes (or similar holes) n.exc 0.5 cum and getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface all as specified and directed. (soft/ loose soil)

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M & L for water proofing treatment on roof slab/ sunken slab including picking, sweeping clean and washing down with water to remove dust & providing water proofing treatment described as under:- (a) Surface preparation:- The surface to receive the treatment shall be thoroughly free of laitance, scales, oil or any other loose material. It should be made free of any sharp object. Cleaning of PCC shall be done with wire brushing to attain smooth levelled surface. Cracks shall be rectified, filled using dual shrinkage compensated Repair Mortar and dried for 72 hours before laying the membrane. (b) Grout:- Providing chemical injection treatment in the form of pressure grouting to the construction joint and cracked portion at 1m c/c by injecting cement slurry mixed with dual shrinkage compensated cementitious grout injection grout additive, in the required consistency through the pre fixed PVC nozzles in the 18mm dia holes, fixing of PVC nozzles with instant setting cement. (c) Angle Fillets:- Providing and making of fillet, 50mm x 50mm on sharp corner of terrace with cement sand polymer mortar (add "multipurpose mortar", 10% by weight of cement). First apply the bonding coat of multi purpose polymer 5-10% diluted in water and add to cement slurry. Apply the bonding slurry and apply the polymer mortar over the sharp edges.

(d) Treatment of pipe entry points:- Preparing the inside surface of core and PVC MS Pipe by roughening using suitable sand paper to get better adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any laitance or loosely flaky particles. Packing the gap using free flowable non shrink cement polymer based grout up to the surface of the bore while bonding agent is in tacky state, the periphery of PVC pipe should be sealed with Hybrid PU sealant of dual shrinkage compensated Micro Concrete. (e) Application of two component Epoxy Primer (Resin & Hardener) on the cleaned surface for bonding of polyurethane with the existing concrete surface. 33% water dilution is recommended with the pure mixed primer. The primer mixing ratio will be 1:3 (Resin : hardener). (f) Supplying, providing and applying waterproofing treatment to roof area with single component highly elastomeric seamless cold applied modified PU coating complete as per manufacturer’s specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have a dual combination of 280% elongation, Material Coverage 1.2 kg/ Sqm for two coats. Makes:- Sika, Fosroc, STP, Choksey, Maruti, Asian Paints, MAPEI, Bostik.

S & F rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S & F 1.25 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. complete all as specified and directed.

Erection and fixing only old retreived rolled sections as in purlins where connected to common rafters fixed with angle cleats or other connecting plates complete all as specified and directed.

M & L for preparing old steel or iron surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M & L for Desludging/desilting of 150 mm dia sewage lines including manholes, up to 2.0 m depth by removing blockage if any by means of rodding manually or mechanically by pumping out water where required and removing residual silt/mud/peat/sludge out side of defence land complete all as specified and directed by Engr-in-charge.

M & L for Extra over rendering for work in isolated widths or in widths not forming part of general plastering such as in bands, cornices, skirtings, drip moulds and similar work n exc 15 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc. complete all as specified and directed.

M & L for Providing and injecting chemical emulsion for Post Constructional Ant termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M & L for Post construction anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

M & L PCC 1:3:6, type C-2, (40 mm graded aggregate) as in surface channels and drains complete all as specified and directed.

M & L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

M & L for 5mm thick rendering in CM 1:3 on fair faces of brick or concrete surfaces to be finished even and smooth over 10 mm thick dubbing coat in CM 1:3 after applying a coat of anti corrosion chemical coating upon exposed reinforcement mixed with water proofing compound, as per manufacturer's instruction etc. complete all as specified and directed. (Note WPC shall be measured and paid separately)

Excavating over areas, n exc1.5 m deep and getting out in any type of soil complete all as specified and directed.

Removing excavated soil exc. 250 m but n exc. 500 m and depositing where directed complete all as specified and directed.

S & F for Stainless Steel (AISI 304 grade ) non magnetic multilayer feuba nickel chrome plated for multipurpose utensils container of following size in each kitchen :- (a) plain basket of size 510x470x100 or 520x485x100 mm-01No (b) multi size plate basket of size 510x470x150 or 520x485x150 mm -01 No (c) cutlery basket,with perforated bottom & side of compacted /slots for holding cutlery of size 510x470x100 or 520x485x100 mm -01 No (d) Plain basket of size 510x470x200 or 520x485x200 mm -01 No (e)Pull out with 02 baskets each of size 150x485x80 or 100x485x80 mm -01 No (f) including frame work , telescopic channels , handles etc as reqd & all as specified sample & design to be approved by GE. Make: Hettich / Hafole.

SCHEDULE 'A' PART- II (Internal Electrification)

Taking down carefully old/ unserviceable copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed by Eng-in-charge.

M & L for point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS-H grade in with suitable size of sunk type cast iron or pressed steel terminal box 1.2mm thick, duly painted for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, including contineous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS-H grade, green colour, up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of the following. (Note: Colour code shall be maintained as per IE rule).

One light point point /bell / buzzer point controlled by one-one way switch.

One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

One three pin 5 Amp socket on same board with other switches.

One three pin 5 Amp socket on independent board

One light point controlled by 2 two-way switch

All as per item No 156.00 above but one 3 pin socket outlet 15 Amp on independent board, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm complete all as specified and directed.

M & L for point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS-H grade in and including medium duty concealed PVC conduit 20 mm dia or higher and conduit fittings and all accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.2mm thick, duly painted for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, including contineous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS-H grade, green colour, up to common earth and connected to earth duly including cutting charges and making good in CM 1:3 compete all as specified and directed by Eng.-in-charge of the following. (Note: Colour code shall be maintained as per IE rule).

One light point point / bell / buzzer point controlled by one-one way switch.

One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

One three pin 5 Amp socket on same board with other switches.

One three pin 5 Amp socket on independent board

One light point controlled by 2 two-way switch

All as per item No 158.00 above but one 3 pin socket outlet 15 Amp on independent board, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm complete all as specified and directed.

S & F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 250 V AC complete all as specified and directed..

S & F lamp holder PVC/polycarbonate type with back plate suitable for batten fittings.250 V AC complete all as specified and directed.

M & L in replacement sub main wiring with 2 Single core PVC insulated unsheathed FRLS-H cable 1100 Volts grade heavy duty copper conductor multistranded of size 6 Sq.mm. (nominal area) drawing in and including 20 mm. dia or higher PVC conduit medium duty concealed, including accessories and fittings. Insulated unsheathed FRLS-H cable copper conductor multistranded of size 6.0 Sq. mm. as earth wire upto common earth and connected to earth duly including cutting charges and making good complete all as specified & directed,including cutting chases ,terminal boxes and making good to walls,floors etc complete all as specified and directed.

S & F in replacement sheet metal enclosures 240 volt with suitable rated bus bar for double door 8 way IP-43DB's lk-09suitable for one MCB SPN as incoming and 6 MCB SP as out going, mounting flush on wall and making good disturbed surfaces complete all as specified and directed by Engr-in-charge . (MCBs shall be measured and paid separately) (Make of DBs / MCBs / MCCBs will be of same make)

Supply & fixing and Testing TP & N Vertical load line (VTPN) 4 way 415 Volts 50 Hz indoor type double door sheet metal enclosure IP-43 DB's IK-09 flush mounted with 250 Amp Copper busbar for each phase with two neutral bar & two earthbar and cable ties for cable management including Provision of MCCB 40 Amps,ICs=100%ICu, 16KA four pole as in comer including connecting terminal strip complete and SP MCBs as out going etc complete pre wired with suitable size copper conductor. The DB's shall hold type test certificate (CPRI) as per IEC 61439-3 complete all as specified and directed by Eng-in-charge. (Note :- MCB/ MCCB shall be measured and paid separately) (Make of DBs / MCBs / MCCBs will be of same make)

S & F MCB double pole 240 Volt 10 KA 40 Amp 'B' series conforming to ISI marked complete all as specified & directed .

S & F MCB single pole and 240 volt 10 KA 5-32 Amp 'B' series conforming to ISI marked all as specified and directed.

S & F MCCB 415 Volt 16 KA 4 pole 63 Amp magnetic trip release & setting as incoming with fixing arrangement complete all as specified and directed.

S & F in replacement wall mounted LED tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed including taking down old tube light fitting . Make: Philips cat part No TMC1001xT LED 13-20w WH(Tube Batten) MAS LED 1200mm 18W-865-T-81 / Wipro Cat part No WIO921208 (Tube Batten) LL13-181-650 (Tube) / Havells Cat Part No REGAL BATTEN T8 UPTO 1X20W SSBS WH( Batten) PHOTONULTRAE2.01213T118WLED 865 SPC

S & F high efficiency LED bulbs 1 X 12 watt that can be used as a ready replacement for existing GLS and CFL direct fit in holder complete all as specified and directed. Make: Philips; Model: Stellar Bright High Wattage, 15000 Life Hour Havells CAT PART NO LHEAABP71L1W012, C&S CAT PART NO CRONA-RND-118WW

Supply & fix ceiling Fan any sweep single phase 230 volts double ball bearing with down rod , canopy, blades etc BEE 5 star rated including connecting with twisted three cord flaxible copper conductor cable (23/.0076 ) from ceiling rose to connector of fan and writing MES NO on fan complete all as specified and directed .

Supply and fix stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc complete all as specified and directed.

Taking down & Refix ceiling Fan 1200 mm / any sweep single phase 230 volts with down rod , canopy, blades etc including painting of ceiling fan and connecting with twisted three cord flaxible copper conductor cable (23/.0076 ) from ceiling rose to connector of fan and writing MES NO on fan complete all as specified and directed.

S & F Geyser vertical mount type 25 Ltrs capacity five star rated ,shockproof and rust proof metal body compact size including two nos PVC connection heavy duty and connecting with all fixing arrangement of nuts & bolts and fixing on wall complete all as specified & directed .

M & L for earthing with galvanized steel earth plate electrode of size 600 mm x 600 mm x 6.0 mm buried directly in ground (earth pit not less than 2.25 Mtr below normal ground level ) connected to galvanized earth lead with GI wire of size 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel including 40 mm dia medium grade GI tubing for protection of earth lead, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm dia, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:2:4 type B1, 50 mm thick precast RCC (1:2:4) type B1 pit cover reinforced with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar including GI wire of 4 mm dia for extension of earth lead and necessary excavation, earth work, in soft/loose soil and disposal of spoils to a disance not exc 50 mtr and necessary connection and testing complete all as shown in electrical plate No. 3 of SSR Pt-I, and all as directed and specified. Note: (i) If the desired earth resistance is not found within permissible limit shall be redone by contractor at no extra cost. (ii) Cost of GI wire 4 sqmm and 15 mm dia pipe medium grade upto 7.5 mtr is included in the rate quoted for this item

S & F air ventilation fan metalic body 300mm, 900 RPM with louvers, single phase, 230V AC including necessary, M&L for making hole fixing arrangement on wall with frame holdfastner, bolt, washer etc including connection with twisted white three core flexible copper multistranded conductor cable from ceiling rose to connector all a directed by Engineer-in-charge.

Supply and Fixing of bus bar chamber out-door type size 750 x 500 x 400 mm deep factory made front and back openable made of 2.0mm thick CRCA sheet powder coated including Aluminium strips(04 No's) suitable for 200 Amps dully insulated ,wired and duly mounted on porcelein insulators,including necessary PCC work, MS framework to fixed the chamber at the height of 30cm from GL / Floor level complete all as specified and directed.

S & F mirror light decorative compact luminarious with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make : Philips CAT PART NO BN021LED12S6500PSUGR, Havells CAT PART NO LHESABP7IN1W009 9W, Wipro MAGMA LED 10 Watt

Supply and Fixing Integral LED Street Light Luminaire with bracket made of GI pipe light garde suitable dia 1.5m long and accessories for fixing on wall comprising of pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 40/45 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life 50,000 burning hours, complete including connection all as specified and directed.

Supply, Laying in replacement and testing cable XLPE Insulated,screened,PVC bedded,galvanised steel strip or wire armoured electric power cables ( heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sqmm ,4 core. complete all as specified and directed.

S & F Switch Piano Flush Button Type 5 Amp SP 250 V AC Complete all as specified and directed.

S & F Switch Piano Flush Button Type 15 Amp SP 250 V AC Complete all as specified and directed.

S & F socket outlet two in one three pin 5 Amp & 15 Amp 250 V AC Flush Type Complete all as specified and directed.

S & F ding dong bell 240 V AC single pole Complete all as specified and directed.

S & F socket outlet multi purpose three pin two in one, 5 Amp 250 V AC Complete all as specified and directed.

S & F bell switch piano flush button type 5 Amp Complete all as specified and directed.

M & L for laying local dry clean sand filling for cushioning in trenches around under ground cable complete all as specified and directed. (Note: The punned thickness will be measured).

M & L for laying well burnt brick, old size in trenches with width equal to the length of brick, as protection of under ground cable complete all as specified and directed.

M & L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

M & L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm but n.exc 20 cm girth complete all as specified and directed.

S & F of 20mm dia non metallic PVC conduit medium duty complete all as specified and directed.

S & F of 25mm dia non metallic PVC conduit medium duty complete all as specified and directed.

SCHEDULE 'A' PART- III (Road / Path / Hardstanding)

Surface excavation n exc 30 cm deep and averaging 15 cm and getting out in any type of soil complete all as specified and directed.

M & L for hard core of gauge n.exc 63mm deposited, spread & levelled in layers n.exc 15cm thick watered and rammed to true surface with broken stones or boulders complete all as specified and directed.

M & L for 100 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub floor /sub base complete all as specified & directed.

M & L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M & L for Machine pressed precast conctete interlocking paver block made from grey cement with pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade complete all as specified and directed.

M & L for cement concrete 1:2:4, type B1 using 20mm graded stone aggaregate as in copings , benching, bedplates etc. including all necessary formwork etc. complete all as specified and directed.

SCHEDULE 'A' PART- IV (Sewage Disposal)

M & L Reinforced concrete pipes, class NP2, of bore 150 mm, laid and jointed with collars in CM 1:1 and tested complete all as specified & directed.

M & L for PCC 1:4:8 Type D-2 using 40mm graded crushed stone aggregate as in bed of drain pipes concrete bed to drain pipe including packing under and haunching against the sides of pipe after they are laid and tested, as shown on drgs for 150mm dia complete all as specified & directed.

M & L for PCC 1:3:6 Type C-2 (using 40mm graded stone agg) as in foundation filling and mass concrete as in bed of Manholes etc complete all as specified & directed.

M & L for brick work in cement mortar 1:4 with sub class `B’ bricks straight or curved on plan exc 6m mean radius with old size bricks complete all as specified & directed. (for manhole etc).

M & L for PCC 1:2:4 type B-1 (using 20mm graded stone agg) as in coping benching bed blocks incl necessary form work complete all as specified & directed.

M & L for PCC 1:2:4 type B-2 (using 40mm graded stone agg) as in surface channel bed/drains/in manholes all as specified laid to slope and finished surface even and smooth complete all as specified & directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement incl forms moulds, mitered/stopped ends etc. complete all as specified & directed.

M & L for 15mm thick rendering on fair faces of brick workor concrete surfaces in cement mortar 1:4 using water proofing compound @ 2% by wt of cement incl finishing the surface even and smooth w/o using extra cement. (WPC shall be measured & paid separately) complete all as specified & directed.

M & L for 15mm thick rendering on other than fair face of brick work or concrete surfaces in cement and sand mortar 1:4 mixed and the finished surface fair and even below GL 150mm complete all as specified & directed.

Supply only integral water proofing compound complete all as specified & directed.

M & L for pre cast RCC cover slab for manholes Type B-1, 1:2:4 (using 20mm grade stone agg) set in cement mortar 1:6 complete all as specified & directed (Note-Reinforcement shall be measured & paid separately)

M & L for Construction of Septic Tank 50 users with brick masonry, PCC in foundation 1:4:8, floor, cover slab, including sludge chamber, CI vent pipe, CI cowl inlet and outlet pipe, RCC baffle wall and all necessary earthwork complete all as specified and directed. Ref. TD 217 sheet 1/7 to 7/7

M & L Soakage wells excavation in any type of soil foundation in PCC 1:3:6 walls of honey combed masonry with top ring of M-25 Concrete including intercepting chamber and screen chamber made of brick masonry in CM, RCC cover slab in M25/SFRC cover interconnecting pipes of RCC/DWC complete filed with brick bats of size 2.40 m x 3.0 m complete all as specified and directed. Ref. TD 309 sheet 1/4 to 4/4

Note : Tenderers may note that amount of credit Rs 7,74,672.10 will be deducted from the total amount arrived, at the time of Acceptance of contract.

RAMAPATI ENGINEERING SERVICES