Infrastructure Development for Circle Headquarter Chetam,Upper Subansiri District.

Amount

SH:SITE DEVELOPMENT

Excavation in decomposed or soft rock with or without blasting including disposal of the same lead upto 50 m and lift upto 1.50 m.

Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when requered, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.

Providing and laying in foundations and plinth cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Centring and shuttering including strutting, propping etc and removal of form work for :-

Column, pillars, posts and struts etc.

Walls (any thickness) including attached pilasters,buttresses, plinth and string courses etc.

Lintels, beams, girders, bressumers and cantilevers etc.

Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5m height).

Reinforcement of RCC work including bending, binding and placing in position complete. :-

Cold twisted bars.

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring, shuttering and reinforcement.

M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding the cost of centring, shuttering and reinforcement.

M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Providing and laying cement concrete 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in:

Walls including attached buttresses, pilasters and their caps and bases and string courses etc. up to floor two level.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses.

0.63 mm thick GI sheet

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including necessary iron butt hinges with necessary screws.

38 mm thick best available local wood, class-B-I

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Cement concrete flooring 1:2:4(1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement.

40 mm thick

Providing and fixing 4.0 mm thick asbestors plain sheet ceiling of approved quality with necessary nails etc.complete (frame work for base to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.

Best local approved quality wood.

Extra for making chamfered edges of beading.

12 mm cement plaster 1 : 5 (1 cement : 5 fine sand).

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

Ornamental grill.

Painting two coats with oil type wood preservative of approved brand and manufacture on new work.

Colour washing such as green, blue or buff on new work (two or more coats) including a base coat of white washing with lime to give an even shade.

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Applying priming coat consisting of a mixture of red lead, white lead and double boiled linseed oil in the ratio of 0.7 Kg : 0.7 Kg : 1 Litre on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1:3(1 cement : 3 fine sand) including shuttering complete.

Providing and laying damp proof course 50 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size).

Providing and fixing local wooden railing 0.75 m high with 7.5 x 5 cm top and bottom rails 7.5 x 5 cm sides and 5 cm x 5 cm intermediate vertical bars placed at 22.5 cm centre to centre including painting two or more coats as directed.

Chequered terrazzo tiles 22 mm thick marble chips of sizes upto 6mm in floors on 25 mm thick bed mortar 1:3 9 ( 1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbbing and polishing complete.

Light shades using white cement

Marble chips skirting (up to 30 cm height) rubbed and polished to granolithic finish top layer 6 mm thick with white, black or white and black marble chips of sized from smallest to 4 mm nominal size laid in cement marble powder mix 3 : 1 (3 cement : 1 marble powder) by weight in proportion of 4:7 ( 4:cement marble powder mix : 7 marble chips) by volume.

Providing and fixing 40x3 mm flat iron hold fasts 40 cm long including fixing to frame with 10mm dia bolts, nuts wooden plugs and embedding in cement concrete blocks 30x10x15 cm in 1:3:6

Providing and fixing 12 mm thick and 150 mm wide pelmet of flat pressed 3 layer particle board (medium density) with 25 mm dia second class teak wood curtain rod and brackets including fixing with 25 x 3 mm MS flat 10 cm long and plugs etc complete.

Providing and fixing 25 mm dia first class Indian teak wood curtain rods with brackets plugs etc wherever required.

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand :8 Graded stone aggregate 40 mm nominal size) inside plastering 12mm thick with cement and making channels in cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20mm nominal size) neatly finished complete as per standard design.

Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight.

Construction of soak pit 1.2 x 1.1 x 1.2 m filled with brick bats including SW drain pipe 100 mm dia and 1.20 m long complete as per standard design.

Providing and fixing white vitreous china type water closet pedestal (European type WC pan) with seat and lid CP brass hinges and rubber buffers, 12.5 Litres high level CI flushing cistern with fittings RS or CI brackets, galvanized steel telescopic flush pipe with fittings and clamps, 20 GI overflow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting making good the walls and floors where required.

WC pan with white plastic seat and lid.

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete

Providing and fixing sink including making all connection excluding cost of fittings.

White glazed fire clay sink size 600x450x150 mm

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.

Providing and fixing 12.5 litres high level CI flushing cistern of approved make with integral fittings such as ball valve, bell, lever, GI chain and pull complete.

Providing & fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws(heavy quality)

a) 750 x 20 mm size

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

c) 25mm nominal bore

d) 32 mm nominal bore

Providing and fixing brass bib cock of approved quality. 15 mm nominal bore

15 mm nominal bor

Providing and fixing brass stop cock of approved quality.

a) 20 mm nominal bore

Syntex 2000 Litrs

Wiring for light point / fan/ call ball point with 1.5 sqmm PVC insulated Aluminium conductor cable in surface consuit (PVC Casing caping) i/c painting etc.

Short Point

Medium Point

Long Point

Wiring for 3 Pin 5Amp plug point with 1.5 sq mm PVC insulated alumenium conductor cable including providing and fixing of 5 Amp socket outlet on switch board in surface PVC casing caping wiring system and 5 Amp piano type switch earth the third pin i/c, painting etc as required.

Medium Point

Wiring for 3 Pin 15Amp plug point with 4 sq mm PVC insulated alumenium conductor cable including providing and fixing of 15 Amp socket outlet on switch board in surface PVC casing caping wiring system and 15 Amp piano type switch earth the third pin i/c, painting etc as required.

Wiring for sub-main wiring with following PVC insulated Aluminium conductor cable in surface PVC casing caping as required.

2 X 2.5 Sq.mm

2 X 4 Sq.mm

Wirring for circuit wirring with 2X1.5 sqmm PVC insulated Aluminium conductor cable single core in surface PVC casing caping along with 1 Nos 2.24 mm dia bare aluminum wire for loof earthing as required.

Wirring for circuit wirring with 2X4 sqmm PVC insulated Aluminium conductor cable single core in surface PVC casing caping along with 1 Nos 2.24 mm dia bare aluminum wire for loof earthing as required.

Supplying and drawing of following size PVC insulated Aluminium conductor cable single core in surface PVC casing caping as required.

2 X 1.5 Sq. mm

2 X 2.5 Sq.mm

2 X 4 Sq.mm

Supply and Fixing of wooden board i/c varnished and connetion etc. as required.

Supply and Fixing of 5A switch on the existing wooden board i/c connection etc. as required

Supply and Fixing of 15A switch on the existing wooden board i/c connection etc. as required

Supply and Fixing of 3 Pin, 5A Socket outlet on the existing wooden board i/c connection etc. as required

Supply and Fixing of 3 Pin,15A Socket outlet on the existing wooden board i/c connection etc. as required

Supply and Fixing of celling rose on the existing wooden board i/c connection etc. as required.

Supply and Fixing of Plain pendant with 16/20 mm twin twished falexible PVC insulated cotton brabided copper cable and brass pendent holder i/c connection etc as required.

Supply and Fixing of bulk head fitting suitable for 100W lamp complete with accessories etc. as required.

Instalation,testing and commissioning of per wired flourescent fitting of all type complete with all accessories and tube etc directly on wall/celling i/c connection with 1.5 sqmm PVC insulated conductor S/C cable etc.

Installtion, testing and commissioning of celling fan and regulator i/c wiring and down rod of standard length (upto 30cm) etc. as required.

Supply of dectrotive1X40W floursent tube fittine complete with all assessores like copper wounded choke, rotter holder, staters, condenser with tube light and aeryliec covers etc as required.

supply and Fixing of 1200mm size electro celing fan capacitor type complet with 30 cm down road, canopies hanging shackle, blades, and speed regulator suitable for use on 230/240 volt 50 HZ single phase AC supply conforming to IS: 374/1979 as required. (Khaitan Make)

Supplying and fixing of following size PVC casing caping on surface as required

15 mm X 10 mm

20 mm X 10 mm

25 mm X 10 mm

30 mm X 10 mm

Supplying and fixing of following size PVC TEE/L/and Sq Box as required

PVC TEE

PVC Sq. Box

PVC external angel

PVC Internal angel

PVC coupler

Supplying and fixing of MS Fan clamp etc as required

Supplying and fixing of call bell/buzzer and piano type bell push, suitable for D.C/A.C single phase, 230 volts, complete as required.

(Sh:- (Main Switch and Service connection)

Supplying & Fixing of 32A TPN MCB main switch with all assessories as required.

Supplying & Fixing of 16A TPN MCB main switch with all assessories as required.

Supplying & Fixing of following way single pole & natural sheet steel MCB distribution board 240Volts on surface/recess complete with tinned copper busbar neutral link earth bar,dinbar, detachable, glad plate, interconnection i/c painting earthing etc as required.

Supply of 32A Cut Out

Supply of 1 PH Energy Meter of range 0-20A i/c wiring etc. as required.

Supply and Fixing of 10 Sq.mm WPTC Alluminium conductor cable for service connection.

Supply and Fixing of 3.2 mtr long, 40 mm diameter service pipe with bend etc as required.

Supplying and fixing of following size Screw

(Sh:- (Earthing)

Earthing with GI pipe 4.50 mtr long and 40 mm diameter with necessary accssories and providing masonary enclosure with copper plate having lockaing arrangement and watering pipe ect(but without charcoal ore coke and salt) complete as required.

Extra for using salt and charcoal/choke for pipe earthing electrode as required.

Supplying and laying 8 SWG GI wire at 0.50 mtr below ground level for conductor earth electrode i/c soldering etc as required.

Providing and laying earth cunnection from earth electrode with 8 SWG GI wire in 15 mm dia GI pipe from earth electro as required.

Providing and fixing 8 SWG GI wire on surface or in recess for loop earthing as required

(SH:Furnishing Furniture Items)

Office VIP Chair with Arms(Godrej Brand)

Office VIP Table(Godrej Brand)

Godrej steel arm chair

Godrej steel Table

Suprime best quality armed chair (for Drawing Room)

Writing table 4'x2'6"x2'6"

Door Curtain

Window Curtain

Polythene Vinyl Carpet

Godrej Almirah (size Big)

(SH: Chain Link Fencing)

Earth work in excvation ………………………..

Providing and laying cement concreate 1:3:6

Reinforcement of RCC work i/c bending binding………….

Main bar 12mm dia.

Stirrups 8 mm dia.

Centering and Shuttering

Providing and laying R.CC with 1:1.5:3

Chainlink fencing ………….

12mm thick cement plaster ………..

Refilling excavated earth ………………….

(SH:T-IV Qrtr-1 No.)

Excavation in decomposed or soft rock with or without blasting including disposal of the same lead upto 50 m and lift upto 1.50 m.

Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when requered, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.

Providing and laying in foundations and plinth cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Centring and shuttering including strutting, propping etc and removal of form work for :-

Column, pillars, posts and struts etc.

Walls (any thickness) including attached pilasters,buttresses, plinth and string courses etc.

Lintels, beams, girders, bressumers and cantilevers etc.

Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5m height).

Reinforcement of RCC work including bending, binding and placing in position complete. :-

Cold twisted bars.

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring, shuttering and reinforcement.

M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding the cost of centring, shuttering and reinforcement.

M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Providing and laying cement concrete 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in:

Walls including attached buttresses, pilasters and their caps and bases and string courses etc. up to floor two level.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses..

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses.

0.63 mm thick GI sheet

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including necessary iron butt hinges with necessary screws.

38 mm thick best available local wood, class-B-I

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Cement concrete flooring 1:2:4(1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement.

40 mm thick

Providing and fixing 4.0 mm thick asbestors plain sheet ceiling of approved quality with necessary nails etc.complete (frame work for base to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.

Best local approved quality wood.

Extra for making chamfered edges of beading.

12 mm cement plaster 1 : 5 (1 cement : 5 fine sand).

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

Ornamental grill.

Painting two coats with oil type wood preservative of approved brand and manufacture on new work.

Colour washing such as green, blue or buff on new work (two or more coats) including a base coat of white washing with lime to give an even shade.

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Applying priming coat consisting of a mixture of red lead, white lead and double boiled linseed oil in the ratio of 0.7 Kg : 0.7 Kg : 1 Litre on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1:3(1 cement : 3 fine sand) including shuttering complete.

Providing and laying damp proof course 50 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size).

Providing and fixing local wooden railing 0.75 m high with 7.5 x 5 cm top and bottom rails 7.5 x 5 cm sides and 5 cm x 5 cm intermediate vertical bars placed at 22.5 cm centre to centre including painting two or more coats as directed.

Chequered terrazzo tiles 22 mm thick marble chips of sizes upto 6mm in floors on 25 mm thick bed mortar 1:3 9 ( 1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbbing and polishing complete.

Light shades using white cement

Marble chips skirting (up to 30 cm height) rubbed and polished to granolithic finish top layer 6 mm thick with white, black or white and black marble chips of sized from smallest to 4 mm nominal size laid in cement marble powder mix 3 : 1 (3 cement : 1 marble powder) by weight in proportion of 4:7 ( 4:cement marble powder mix : 7 marble chips) by volume.

Providing and fixing 40x3 mm flat iron hold fasts 40 cm long including fixing fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm in 1:3:6

Providing and fixing 12 mm thick and 150 mm wide pelmet of flat pressed 3 layer particle board (medium density) with 25 mm dia second class teak wood curtain rod and brackets including fixing with 25 x 3 mm MS flat 10 cm long and plugs etc complete.

Providing and fixing 25 mm dia first class Indian teak wood curtain rods with brackets plugs etc wherever required.

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand :8 Graded stone aggregate 40 mm nominal size) inside plastering 12mm thick with cement and making channels in cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20mm nominal size) neatly finished complete as per standard design.

Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight.

Construction of soak pit 1.2 x 1.1 x 1.2 m filled with brick bats including SW drain pipe 100 mm dia and 1.20 m long complete as per standard design.

Providing and fixing white vitreous china type water closet pedestal (European type WC pan) with seat and lid CP brass hinges and rubber buffers, 12.5 Litres high level CI flushing cistern with fittings RS or CI brackets, galvanized steel telescopic flush pipe with fittings and clamps, 20 GI overflow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting making good the walls and floors where required.

WC pan with white plastic seat and lid.

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete

Providing and fixing sink including making all connection excluding cost of fittings.

White glazed fire clay sink size 600x450x150 mm

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.

Providing and fixing 12.5 litres high level CI flushing cistern of approved make with integral fittings such as ball valve, bell, lever, GI chain and pull complete.

Providing & fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws(heavy quality)

a) 750 x 20 mm size

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

c) 25mm nominal bore

d) 32 mm nominal bore

Providing and fixing brass bib cock of approved quality. 15 mm nominal bore

15 mm nominal bor

Providing and fixing brass stop cock of approved quality.

a) 20 mm nominal bore

Syntex 2000 Litrs

Wiring for light point / fan/ call ball point with 1.5 sqmm PVC insulated Aluminium conductor cable in surface consuit (PVC Casing caping) i/c painting etc.

Short Point

Medium Point

Long Point

Wiring for 3 Pin 5Amp plug point with 1.5 sq mm PVC insulated alumenium conductor cable including providing and fixing of 5 Amp socket outlet on switch board in surface PVC casing caping wiring system and 5 Amp piano type switch earth the third pin i/c, painting etc as required.

Medium Point

Wiring for 3 Pin 15Amp plug point with 4 sq mm PVC insulated alumenium conductor cable including providing and fixing of 15 Amp socket outlet on switch board in surface PVC casing caping wiring system and 15 Amp piano type switch earth the third pin i/c, painting etc as required.

Wiring for sub-main wiring with following PVC insulated Aluminium conductor cable in surface PVC casing caping as required.

2 X 2.5 Sq.mm

2 X 4 Sq.mm

Wirring for circuit wirring with 2X1.5 sqmm PVC insulated Aluminium conductor cable single core in surface PVC casing caping along with 1 Nos 2.24 mm dia bare aluminum wire for loof earthing as required.

Wirring for circuit wirring with 2X4 sqmm PVC insulated Aluminium conductor cable single core in surface PVC casing caping along with 1 Nos 2.24 mm dia bare aluminum wire for loof earthing as required.

Supplying and drawing of following size PVC insulated Aluminium conductor cable single core in surface PVC casing caping as required.

2 X 1.5 Sq. mm

2 X 2.5 Sq.mm

2 X 4 Sq.mm

Supply and Fixing of wooden board i/c varnished and connetion etc. as required.

Supply and Fixing of 5A switch on the existing wooden board i/c connection etc. as required

Supply and Fixing of 15A switch on the existing wooden board i/c connection etc. as required

Supply and Fixing of 3 Pin, 5A Socket outlet on the existing wooden board i/c connection etc. as required

Supply and Fixing of 3 Pin,15A Socket outlet on the existing wooden board i/c connection etc. as required

Supply and Fixing of celling rose on the existing wooden board i/c connection etc. as required.

Supply and Fixing of celling rose on the existing wooden board i/c connection etc. as required.

Supply and Fixing of Plain pendant with 16/20 mm twin twished falexible PVC insulated cotton brabided copper cable and brass pendent holder i/c connection etc as required.

Supply and Fixing of bulk head fitting suitable for 100W lamp complete with accessories etc. as required.

Instalation,testing and commissioning of per wired flourescent fitting of all type complete with all accessories and tube etc directly on wall/celling i/c connection with 1.5 sqmm PVC insulated conductor S/C cable etc.

Installtion, testing and commissioning of celling fan and regulator i/c wiring and down rod of standard length (upto 30cm) etc. as required.

Supply of dectrotive1X40W floursent tube fittine complete with all assessores like copper wounded choke, rotter holder, staters, condenser with tube light and aeryliec covers etc as required.

supply and Fixing of 1200mm size electro celing fan capacitor type complet with 30 cm down road, canopies hanging shackle, blades, and speed regulator suitable for use on 230/240 volt 50 HZ single phase AC supply conforming to IS: 374/1979 as required. (Khaitan Make)

Supplying and fixing of following size PVC casing caping on surface as required

15 mm X 10 mm

20 mm X 10 mm

25 mm X 10 mm

30 mm X 10 mm

Supplying and fixing of following size PVC TEE/L/and Sq Box as required

PVC TEE

PVC Sq. Box

PVC external angel

PVC Internal angel

PVC coupler

Supplying and fixing of MS Fan clamp etc as required

Supplying and fixing of call bell/buzzer and piano type bell push, suitable for D.C/A.C single phase, 230 volts, complete as required.

(Sh:- (Main Switch and Service connection)

Supplying & Fixing of 32A TPN MCB main switch with all assessories as required.

Supplying & Fixing of 16A TPN MCB main switch with all assessories as required.

Supplying & Fixing of following way single pole & natural sheet steel MCB distribution board 240Volts on surface/recess complete with tinned copper busbar neutral link earth bar,dinbar, detachable, glad plate, interconnection i/c painting earthing etc as required.

Supply of 32A Cut Out

Supply of 1 PH Energy Meter of range 0-20A i/c wiring etc. as required.

Supply and Fixing of 10 Sq.mm WPTC Alluminium conductor cable for service connection.

Supply and Fixing of 3.2 mtr long, 40 mm diameter service pipe with bend etc as required.

Supplying and fixing of following size Screw

(Sh:- (Earthing)

Earthing with GI pipe 4.50 mtr long and 40 mm diameter with necessary accssories and providing masonary enclosure with copper plate having lockaing arrangement and watering pipe ect(but without charcoal ore coke and salt) complete as required.

Extra for using salt and charcoal/choke for pipe earthing electrode as required.

Supplying and laying 8 SWG GI wire at 0.50 mtr below ground level for conductor earth electrode i/c soldering etc as required.

Providing and laying earth cunnection from earth electrode with 8 SWG GI wire in 15 mm dia GI pipe from earth electro as required.

Providing and fixing 8 SWG GI wire on surface or in recess for loop earthing as required

(SH:Furnishing Furniture Items)

Wooden Cot

PVC Chair

Wooden Writing table

Wooden Armed chair

Meat safe

RO Water Filter

Wooden Dining Table

Wooden Dining Chair

Wooden Sofa Set

Centre Table

Wooden Tea Pot

Wooden Dressing Table(Ordinary)

(SH:TYPE-II,1 No.)

Excavation in decomposed or soft rock with or without blasting including disposal of the same lead upto 50 m and lift upto 1.50 m.

Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when requered, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.

Providing and laying in foundations and plinth cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Centring and shuttering including strutting, propping etc and removal of form work for :-

Column, pillars, posts and struts etc.

Walls (any thickness) including attached pilasters,buttresses, plinth and string courses etc.

Lintels, beams, girders, bressumers and cantilevers etc.

Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5m height).

Reinforcement of RCC work including bending, binding and placing in position complete. :-

Cold twisted bars.

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring, shuttering and reinforcement.

M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding the cost of centring, shuttering and reinforcement.

M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Providing and laying cement concrete 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in:

Walls including attached buttresses, pilasters and their caps and bases and string courses etc. up to floor two level.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses..

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses.

0.63 mm thick GI sheet

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including necessary iron butt hinges with necessary screws.

38 mm thick best available local wood, class-B-I

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Cement concrete flooring 1:2:4(1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement.

40 mm thick

Providing and fixing 4.0 mm thick asbestors plain sheet ceiling of approved quality with necessary nails etc.complete (frame work for base to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.

Best local approved quality wood.

Extra for making chamfered edges of beading.

12 mm cement plaster 1 : 5 (1 cement : 5 fine sand).

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

Ornamental grill.

Painting two coats with oil type wood preservative of approved brand and manufacture on new work.

Colour washing such as green, blue or buff on new work (two or more coats) including a base coat of white washing with lime to give an even shade.

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Applying priming coat consisting of a mixture of red lead, white lead and double boiled linseed oil in the ratio of 0.7 Kg : 0.7 Kg : 1 Litre on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1:3(1 cement : 3 fine sand) including shuttering complete.

Providing and laying damp proof course 50 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size).

Providing and fixing local wooden railing 0.75 m high with 7.5 x 5 cm top and bottom rails 7.5 x 5 cm sides and 5 cm x 5 cm intermediate vertical bars placed at 22.5 cm centre to centre including painting two or more coats as directed.

Chequered terrazzo tiles 22 mm thick marble chips of sizes upto 6mm in floors on 25 mm thick bed mortar 1:3 9 ( 1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbbing and polishing complete.

Light shades using white cement

Marble chips skirting (up to 30 cm height) rubbed and polished to granolithic finish top layer 6 mm thick with white, black or white and black marble chips of sized from smallest to 4 mm nominal size laid in cement marble powder mix 3 : 1 (3 cement : 1 marble powder) by weight in proportion of 4:7 ( 4:cement marble powder mix : 7 marble chips) by volume.

Providing and fixing 40x3 mm flat iron hold fasts 40 cm long including fixing fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm in 1:3:6

Providing and fixing 12 mm thick and 150 mm wide pelmet of flat pressed 3 layer particle board (medium density) with 25 mm dia second class teak wood curtain rod and brackets including fixing with 25 x 3 mm MS flat 10 cm long and plugs etc complete.

Providing and fixing 25 mm dia first class Indian teak wood curtain rods with brackets plugs etc wherever required.

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand :8 Graded stone aggregate 40 mm nominal size) inside plastering 12mm thick with cement and making channels in cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20mm nominal size) neatly finished complete as per standard design.

Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight.

Construction of soak pit 1.2 x 1.1 x 1.2 m filled with brick bats including SW drain pipe 100 mm dia and 1.20 m long complete as per standard design.

Providing and fixing white vitreous china type water closet pedestal (European type WC pan) with seat and lid CP brass hinges and rubber buffers, 12.5 Litres high level CI flushing cistern with fittings RS or CI brackets, galvanized steel telescopic flush pipe with fittings and clamps, 20 GI overflow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting making good the walls and floors where required.

WC pan with white plastic seat and lid.

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete

Providing and fixing sink including making all connection excluding cost of fittings.

White glazed fire clay sink size 600x450x150 mm

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.

Providing and fixing 12.5 litres high level CI flushing cistern of approved make with integral fittings such as ball valve, bell, lever, GI chain and pull complete.

Providing & fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws(heavy quality)

a) 750 x 20 mm size

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

c) 25mm nominal bore

d) 32 mm nominal bore

Providing and fixing brass bib cock of approved quality. 15 mm nominal bore

15 mm nominal bor

Providing and fixing brass stop cock of approved quality.

a) 20 mm nominal bore

Syntex 2000 Litrs

Wiring for light point / fan/ call ball point with 1.5 sqmm PVC insulated Aluminium conductor cable in surface consuit (PVC Casing caping) i/c painting etc.

Short Point

Medium Point

Long Point

Wiring for 3 Pin 5Amp plug point with 1.5 sq mm PVC insulated alumenium conductor cable including providing and fixing of 5 Amp socket outlet on switch board in surface PVC casing caping wiring system and 5 Amp piano type switch earth the third pin i/c, painting etc as required.

Medium Point

Wiring for 3 Pin 15Amp plug point with 4 sq mm PVC insulated alumenium conductor cable including providing and fixing of 15 Amp socket outlet on switch board in surface PVC casing caping wiring system and 15 Amp piano type switch earth the third pin i/c, painting etc as required.

Wiring for sub-main wiring with following PVC insulated Aluminium conductor cable in surface PVC casing caping as required.

2 X 2.5 Sq.mm

2 X 4 Sq.mm

Wirring for circuit wirring with 2X1.5 sqmm PVC insulated Aluminium conductor cable single core in surface PVC casing caping along with 1 Nos 2.24 mm dia bare aluminum wire for loof earthing as required.

Wirring for circuit wirring with 2X4 sqmm PVC insulated Aluminium conductor cable single core in surface PVC casing caping along with 1 Nos 2.24 mm dia bare aluminum wire for loof earthing as required.

Supplying and drawing of following size PVC insulated Aluminium conductor cable single core in surface PVC casing caping as required.

2 X 1.5 Sq. mm

2 X 2.5 Sq.mm

2 X 4 Sq.mm

Supply and Fixing of wooden board i/c varnished and connetion etc. as required.

Supply and Fixing of 5A switch on the existing wooden board i/c connection etc. as required

Supply and Fixing of 15A switch on the existing wooden board i/c connection etc. as required

Supply and Fixing of 3 Pin, 5A Socket outlet on the existing wooden board i/c connection etc. as required

Supply and Fixing of 3 Pin,15A Socket outlet on the existing wooden board i/c connection etc. as required

Supply and Fixing of celling rose on the existing wooden board i/c connection etc. as required.

Supply and Fixing of Plain pendant with 16/20 mm twin twished falexible PVC insulated cotton brabided copper cable and brass pendent holder i/c connection etc as required.

Supply and Fixing of bulk head fitting suitable for 100W lamp complete with accessories etc. as required.

Instalation,testing and commissioning of per wired flourescent fitting of all type complete with all accessories and tube etc directly on wall/celling i/c connection with 1.5 sqmm PVC insulated conductor S/C cable etc.

Installtion, testing and commissioning of celling fan and regulator i/c wiring and down rod of standard length (upto 30cm) etc. as required.

Supply of dectrotive1X40W floursent tube fittine complete with all assessores like copper wounded choke, rotter holder, staters, condenser with tube light and aeryliec covers etc as required.

supply and Fixing of 1200mm size electro celing fan capacitor type complet with 30 cm down road, canopies hanging shackle, blades, and speed regulator suitable for use on 230/240 volt 50 HZ single phase AC supply conforming to IS: 374/1979 as required. (Khaitan Make)

Supplying and fixing of following size PVC casing caping on surface as required

15 mm X 10 mm

20 mm X 10 mm

25 mm X 10 mm

30 mm X 10 mm

Supplying and fixing of following size PVC TEE/L/and Sq Box as required

PVC TEE

PVC Sq. Box

PVC external angel

PVC Internal angel

PVC coupler

Supplying and fixing of MS Fan clamp etc as required

Supplying and fixing of call bell/buzzer and piano type bell push, suitable for D.C/A.C single phase, 230 volts, complete as required.

(Sh:- (Main Switch and Service connection)

Supplying & Fixing of 32A TPN MCB main switch with all assessories as required.

Supplying & Fixing of 16A TPN MCB main switch with all assessories as required.

Supplying & Fixing of following way single pole & natural sheet steel MCB distribution board 240Volts on surface/recess complete with tinned copper busbar neutral link earth bar,dinbar, detachable, glad plate, interconnection i/c painting earthing etc as required.

Supply of 32A Cut Out

Supply of 1 PH Energy Meter of range 0-20A i/c wiring etc. as required.

Supply and Fixing of 10 Sq.mm WPTC Alluminium conductor cable for service connection.

Supply and Fixing of 3.2 mtr long, 40 mm diameter service pipe with bend etc as required.

Supplying and fixing of following size Screw

(Sh:- (Earthing)

Earthing with GI pipe 4.50 mtr long and 40 mm diameter with necessary accssories and providing masonary enclosure with copper plate having lockaing arrangement and watering pipe ect(but without charcoal ore coke and salt) complete as required.

Extra for using salt and charcoal/choke for pipe earthing electrode as required.

Supplying and laying 8 SWG GI wire at 0.50 mtr below ground level for conductor earth electrode i/c soldering etc as required.

Providing and laying earth cunnection from earth electrode with 8 SWG GI wire in 15 mm dia GI pipe from earth electro as required.

Providing and fixing 8 SWG GI wire on surface or in recess for loop earthing as required

(SH:Furnishing Furniture Items)

Wooden Cot

PVC Chair

Wooden Writing table

Wooden Armed chair

Meat safe

RO Water Filter

Wooden Dining Table

Wooden Dining Chair

Centre Table

Wooden Tea Pot

Wooden Dressing Table(Ordinary)

M/s M.G. ENTERPRISE (BID ID -6778)