CERTAIN B/R REPAIR IN SINGLE LIVING AND OTHER OTM ACCNS AT AF-I UNDER GE (AF) JAMNAGAR NO.2

Amount

Demolition of concrete surfaces in ground floor and paving n.exc. 15cm thickness (below or above ground level) and removing the same to a distance of 1.5 km including loading and dumping / levelling at the destination all as specified.

M&L for 100 mm thick cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) as in floor / hard standing etc finishing the surface even and smooth without using extra cement and spike rolling to surface or making impressions of expanded metal, whilst the concrete is green complete all as specified and directed.

M&L for 75mm thick plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection including finished the surface even and smooth without using of extra cement complete all as specified and directed.

Demolition of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including removal of debris to outside MOD land complete all as specified and directed.

M & L for 25 mm thick cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in levelling course complete all as specified and directed.

M&L for non-skid joint free coloured ceramic tiles (1st quality) not less than 7 mm thick tiles of size exc 0.06 sqm but n exc 0.11 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over & including 15mm screed bed or bedding in CM 1:6 complete all as specified and directed.

M&L for non-skid joint free coloured ceramic tiles (1st quality) not less than 7mm thick tiles of size exc 0.11 sqm but n exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over & including 15mm screed bed or bedding in CM 1:6 complete all as specified and directed.

M&L for non-skid joint free coloured ceramic tiles (1st quality) not less than 7mm thick tiles of size exc 0.18 sqm but n exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over & including 15mm screed bed or bedding in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surface 300 x 450 x 7-8mm / 450 x 350 x 7-8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat of mortar in CM 1:4 for laying wall tiles finishes complete all as specified and directed.

Dismantling of kota stone slabs and granite tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons cills or platform etc complete all as specified and directed.

M&L for granite work 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms laid over and including 15 mm thick screed bed in CM 1:6, including pointing in coloured cement (1:2) using marble dust with admixture of pigment to match with granite shade complete all as specified and directed.

M & L for machine cut & machine polished kota stone slab 18 to 20 mm thick as in kitchen platform, treads of steps laid over and including 15 mm thick screed bed in CM 1:6, jointed with grey cement slurry mixed with colour pigment to match the shade of the slab, rubbing and polishing complete all as specified and directed.

M&L for 18-20mm thick machine cut kota stone slab in riser of steps, skirting,dado and pillar laid over cement mortar in 1:4 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for rounding to edges of granite / kota stone slabs edge, such as in steps cooking platform, and other similar situation.

Dismantling of paver block including demolition of cement mortar bedding or backing coat, including removal of debris to outside MD land complete all as specified and directed.

M&L for 100mm thick cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for 25mm sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M & L for machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade complete all as specified and directed.

Relaying machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing (measured overall as fixed along the centre line over fittings and accessories complete all as specified and directed.

S&F PVC (SWR) pipes 75 mm dia single socketed, in any length, with rubber ring joints jointed with solvent cement, fixed to walls complete all as specified and directed.

S&F PVC (SWR) pipes 75 mm dia single socketed, in any length, with rubber ring joints jointed with solvent cement, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) pipes 110 mm dia single socketed, in any length, with rubber ring joints jointed with solvent cement, fixed to walls complete all as specified and directed.

S&F PVC (SWR) pipes 110 mm dia single socketed, in any length, with rubber ring joints jointed with solvent cement, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bends 110 mm dia complete all as specified and directed.

S&F PVC (SWR) bends 75 mm dia complete all as specified and directed.

Taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, including removal of debries to a distance exc 1.5km but n. exc 2km complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:6 on brick or stone walls to be finished even and smooth (without using extra lime or cement) complete all as specified and directed .

M&L for 15 mm thick rendering in two layers of 10mm and 5mm thick cement mortar 1:4 on stone / PCC block masonry wall surface, including mixing liquid water proofing compound in second layer only as per manufacturers instructions, finished the surface even & smooth without using extra cement complete all as specified and directed. Note:- WPC will be measured & paid separately

M&L for 5 mm thick rendering in cement mortar 1:3 on on ceiling, finished the surface even & smooth without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls & applying two coats of distemper oil emulsion over a coat of chalk whitening compatible primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coat of cement base paint over a coat of primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall/ridge, fixed with self tapping screws complete all as specified and directed.

M & L for providing, cement concrete in coping / roof kerbs or mud stops, rounded or chamfered on edges type B0 1:2:4 (using 12.5mm graded stone aggreagte) complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M & L for framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M & L for rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M & L roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F for steel work in tubular trusses including special shaped washer etc. using ERW or induction butt welded tubes conforming to I. S.11611979 grade ST-240 complete all as specified and directed.

M&L for preparation of new surfaces of steel exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Demolition of brick work / stone work / PCC block masonry built in cement mortar complete all as specified and directed.

M & L for pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in cement mortar 1:4 type C1 (1:3:6) (using 20mm graded stone aggreagate) complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 using on other than fair faces of brick work or concrete surfaces and finish the surface even and smooth without using extra cement all as specified and as directed.

S & F in repairs 20 mm dia curtain rails, mild steel, chromium plated with fixing brackets / concealed brackets & holders, stops, rollers etc including decorative type fitting complete all as specified and directed.

S & F in repairs Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40 mm to wooden / iron / aluminium frame with wooden / iron / aluminium beading and fixed with nails / nut & bolts or wire staples complete all as specified and directed.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) three track window (two shutters glazed) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in Member for wire gauge Section shall be 18.00 x 25.00 x 1.35 (Section No 20791). position, concelled type lock for all two shutter, PVC roller etc all as specified below, including taking down old window complete all as specified and directed. (a) Frame (top & side) section shall be of size 92.00 x 31.75 x 1.50 mm (Section No 20831) (b) Frame (bottom) section shall be of size 92.00 x 31.75 x 1.50 mm (Section No 20832) (c) Top & side Members of shutter Section shall be of size 18.00 x 40.00 x 1.55mm (Section No 20738) (d) Shutter Interlock Section shall be of size 18.00 x 40.00 x 1.45mm (Section No 20737) (e) Bottom Members of shutter Section shall be of size 18.00 x 40.00 x 1.55mm (Section No 20736) Note:- Section No given above are of make Jidal, Contractor may use similar section of other make mention in Appx B.

S&F aluminium (powder coated with approved colour) ventilator, partialy glazed and partialy louvers, outer frame & mullion fabricated with aluminium section of size 82.50 mm x 38.00 mm x 1.70 mm thick (Cat No 20036), half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portaion louvers of 80 mm wide & 4 mm thick frosted glass including aluminium louver patti including S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aparture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position including taking down old ventilator complete all as specified and directed. Note:-(i) Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx B.

KRISHNA ENTERPRISE

sanu enterprise

S t modi

Suraj Builders