REPAIR TO COMPOUND WALLS, FENCING GATES, DRAIN, PATH, HARD STANDING AND MISC WORKS UNDER THE AREA OF AGE B/R-II OF GE (A) NO.1 JODHPUR.

Amount

Demolition of cement concrete reinforced in manhole covers in any position not other wise specifically provided complete all as specified and as directed.

M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in landings, cover slabs (for man holes etc) chullah hoods,chajjas,water troughs,shelves and similar articles with plain faces complete all as specified and as directed .

M&L for TMT bars 6 to 8mm dia and over, cut to length , bent to shape required including cranking, bending & binding with MS wire (annealed ) not less than 0.9mm dia or securing with clips, as in stirrups also & all as specified.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed.

M&L PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate, as in sub base of floor incld. compaction properly & universal and laid to level, complete all as specified and directed.

M & L 28-30 mm thick chequered cement concrete tiles (lacquer coated) in any size & shape with 4-5 mm thick anti abrasive material topping layer (size, shape & shade as approved by GE), with grey cement and pigments, set, jointed and pointed in neat cement slurry as in floors/ path etc over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any description, ( colour, design & pattern, & size/ shape, as approved by GE) as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Supply and laying machine / factory made kerb stone of M-25 grade,at or near ground level, cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed.

Dismantling of posts or struts (wood, steel or RCC) any section,embedded in Cement concrete under natural ground including taking out embedded portion and making good disturbed ground complete all as specified and as directed.

Excavating in post holes or similar holes each not n exc 0.50 cu.m,getting out any type of soil,returning,fillig in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm complete all as specified and as directed.

Demolition of stone / boulder masonry walling, built in cement mortar including all quoins, arches, pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and directed.

M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed.

All as per item No. 12.00 here-in-above, but except stone

Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface n exc 20mm and dressing face beds and joints, complete all as specified and directed.

Dismantling of fencing wire mesh / GI cattle fencing, any type and any size complete all as specified and as directed.

Dismantling of barbed wire, any type and any size complete all as specified and as directed.

S&F mild steel sections like angle, flat etc in post and struts in fencing or with swan neck,, including cutting top to shape as directed,drilling holes,notching for wire etc;flat iron fillets (for securing wire mesh etc including all necessary drilling,bolting or riviting etc confirming to Fe-290Gde E-165 complete all as specified and as directed.

Supply only Mild steel round or square bars 10mm dia.,in available length Fe-290 (Gde-165) for fixing of chain link fencing complete all as specified and as directed.

Supply only Chain link MS galvanised fencing any size or type (The max. size of mesh does not exc 50mm x 50mm and dia of wire exc 3mm.) as approved by G.E. Note:- BOO will consitute by GE to determinate the weight of chainlink.

Fixing only Chain link fencing including line wires,any mesh, size and type to any standards,rails straining bolts, etc. including provision of binding wire complete all as specified and as directed. Note:(i)-Chainlink will be obtained from item No. 19.00 here-in-before.

S&F galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as specified and as directed. Note : - Each line wire to be measured.

Fixing only in repairs for galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as specified and as directed. Note : - Each line wire to be measured.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n. exc 10cm long and dia 5 to 10 mm complete all as specified and as directed.

M&L precast cement concrete block masonry using PCC 1:3:6, type B-1 solid blocks, 10 cm in width and setting in cement mortar 1:6, straight or curved on plan exceeding 6 m mean radius complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 by using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete for & coping fencing post complete all as specified and as directed .

Dismantling structural/non structral steel work including doors, gates etc complete all as specified and directed.

M&L for rolled mild steel work confirming to Fe 410-W, Grade-E- 250, Quality-A as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings [exclusive of steel sheeting or other covering, running rails and guides] and hanging, also fastening and fixing complete all as specified and as directed.

M&L for welding cast iron designer pieces ornamental type with intricate designs & like spirals , Spikes etc as per sample fixed to steel gate by welding., complete all as specified and as directed.

Taking down cement plaster any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified and as directed.

M&L for 15 mm thick rendering in CM 1:4 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished surface even and smooth without using extra cement, complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of wall and applying three coats of white wash on wall surfaces complete all as specified and as directed.

M&L for preparation of old decorated wall surfaces plastered or unplastered, by brooming down or steel wire brushing, scrapping down moulds, moss and efflorescent salts and trading oil & greasy spots, including cornices etc and applying one coat of white wash on wall, complete all as specified and directed.

S&F in repair Fibre glass reinforced translucent 2 mm thick corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof ,wall etc complete all as specified and as directed.

M&L preparation of new or previously untreated steel surface of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over & including M&L single coat of red- oxide, zinc chrome primer complete all as specified and as directed.

M&L for preparation of old painted steel surfaces of any description otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint of any tint complete all as specified and as directed .

M&L for precast cement concrete Type C-0 1:3:6 (12.50mm graded aggregate) as in louvres and jallies, cement grill any type model of Zafri , 35mm thick (measured solid), set in cement mortar 1:6 fixed with PCC post, incld. all mouldings complete all as specified and directed.

M&L for precast cement concrete1:3:6, type C-0 by using 12.5mm graded stone aggregate as in pillars of size 100 x100 mm and height 750mm to provide support of RCC jallies, jointed with neat cement slurry, in CM 1:6, complete all as specified and as directed.

M&L preparation of new/old plastered or un-plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and as directed.

M&L for preparation of old decorated wall surfaces plastered or unplastered and applying one coat of cement base paint on wall, coloured and shade as approved by GE, complete all as specified and directed.

S&F in repairs 25-30 mm thick precast cement concrete 1:3:6 type C1 using 20mm graded stone aggregate as in Kangooras width 30 cm with intricate design on one side all as per sample, incl applying 2 coats of cement base paint on exposed surfaces, complete all as specified & directed.

NOTE:- (i)- The contract sum shall be arrived at after duducting amount of schedule of "Credit" from the Total quoted amount

m/s Firoz khan (BID ID -3081713)

SNEH CORPORATION (BID ID -3082909)

BEYLIM INFRA (BID ID -3082835)

SN TECHNO CONSTRUCTIONS (BID ID -3080470)

PREM TRADERS (BID ID -3083577)

M/s Ajay kumar Garge (BID ID -3080525)

SHREE AASHAPURA ENTERPRISES (BID ID -3073926)