CWE/FZR- /2020-21 Special Repair to Bldg No P-15,P-16,P-17,P-18 and P-276 (5 ESHs) in Depot Area at FAD Baddowal under GE Ludhiana

Amount

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level), complete all as specified.

Demolition of reinforced cement concrete as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, complete all as specified

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc, complete all as specified.

Dismantling of brick work built in cement mortar of any specification and in any position complete all as specified. Note:- The rate include for the support to the existing RCC roof supported on wall to be dismantled.

Demolition of brick work built in cement mortar of any specification and in any position complete all as specified.

M&L for Taking down wooden/steel chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Square metre each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts,making good jambs with plaster in CM(1:4) to match with existing finish, complete all as specified.

M&L for 100mm thick Cement concrete (1:2:4) type B-2 using 40mm graded stone aggregate as in flooring, complete all as specified.

M&L for brushing neat cement slurry with 3.0 kg of cement per sq. metre complete all as specified.

M&L for Cement concrete (1:3:6) type C-2 using 20 mm graded stone aggregate as in 75mm thick plinth protection, surfaces finished even and fair without using extra cement, including provision of construction joints, complete all as specified and directed

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound, complete all as specified and directed

M&L for use & waste wooden form work (rough finished surfaces ) to chullah hoods, chajjas, troughs and similar items including edges, complete all as specified

M&L for reinforced cement concrete (1:2:4), type B-1 using 20 mm graded stone aggregate as in Chajjas etc, complete all as specified.

M&L form work (rough finished flat surfaces) to sides & soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports overhangs, etc also splays between floors and beams, floor/roof slab, landings and similar work, complete all as specified.

M&L for reinforced cement concrete (1:2:4), type B-1 using 20 mm graded stone aggregate as in lintel and beam etc, complete all as specified.

M&L form work (rough finished surfaces) to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc.20cm wide, complete all as specified.

M&L form work (rough finished flat surfaces) to soffits of suspended slab n exc 200mm thick and similar work, complete all as specified.

M&L for reinforced cement concrete (1:2:4), type B-1 using 20 mm graded stone aggregate as in slab supported on wall etc, complete all as specified.

M&L for Rendering 15 mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, mixed with WPC @ 3% by weight of cement (WPC shall be measured and paid seaparately) finished even and smooth without using extra cement, complete all as specified.

M&L for Rendering 15 mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

M&L Rendering 5 mm thick in cement mortar (1:3) on ceiling concrete surfaces finished even and smooth without using extra cement, complete all as specified.

M&L Steel windows or ventilators, fixed type, with glazing bars, complete all as specified.

M&L for welding in running for thickness of metal to be welded n.exc 6mm, complete all as specified.

S&F Wire netting of galvanised steel wire 1.40mm dia and size of mesh 12mm, fixed with tinned tacks of wire staples, complete all as specified.

M&L Preparation of newly plastered surfaces of wall & applying three coats of white wash, complete all as specified.

M&L Preparation of old decorated plastered or unplastered surfaces by brooming down with steel wire brush, scarping down smoke soot, mould,moss and efflorescent salts and trading oil, greasy spots and applying one coat of white wash on walls including cornices, pillasters etc, complete all as specified and as directed.

M&L Preparation of newly plastered surfaces of ceiling & applying two coats of white wash, complete all as specified.

M&L Preparation of old plastered surfaces of ceiling & applying one coats of white wash, complete all as specified.

M&L Preparation of new plastered surfaces walls etc and applying two coats of cement base paint over a coat of primer (camouflage pattern), complete all as specified.

M&L Complete removal of existing treatment and preparation of old plastered surfaces of walls and applying two coats of cement base paint (camouflage pattern), complete all as specified.

M&L Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint (camouflage pattern) over a coat of red oxide primer, complete all as specified.

M&L Preparation of old treated steel surfaces of any description, over 10cm width or girth and applying two coat of synthetic enamel paint (camouflage pattern), complete all as specified.

S&F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work, complete all as specified.

Supply only integral water proofing compound ISI marked, complete all as specified.

M&L for Cutting holes in brick walls built in cement mortar or cement lime mortar and stone walls for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required, complete all as specified.

Demolition and breaking up drain pipes 100mm/75mm (Salt glazed stone ware, AC or Reinforced concrete) set in cement mortar, complete all as specified.

S&F 110 mm bore PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall/floor complete all as specified.

S&F in repairs 110 mm bore PVC (SWR) bends/shoe and provided with access door any radius fixed to walls including distance pieces and stack clamps, including making good around complete all as specified.

M&L for APP based Polymer modified bituminous membrane with sand witched polythene film/non woven polyster reinforcement/polymeric water proofing membrane 3Kg/sqm laid over hot blown grade 85/25@ 1.2kg/Sqm (i.e roof slab cleaned throughly to remove all loose particle dust/dirt particle) shall be laid over entire roof surface and on verticle surface up to grooves (or as per manufacturers recommendation) with over laps of 100mm. The over lap shall be sealed by flames or as per manufacturer instruction. Hot blown bitumen grade 85/25 @1.2kg/Sqm applied over the membrane should be compatible with membrane all as recommendation of manufacturers and all as specified and directed.

M&L for screed 10mm thick in cement mortar (1:3) on roof surfaces admixed with water proofing coumpound as approved by GE, (WPC shall be measured and paid seaparately) finished even and smooth without using extra cement complete all as specified.

M&L for Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius, complete all as specified.

M&L for preparation of sealing surfaces previously treated with tar, bituminous composition, etc with one coat of knotting in preparation for painting on surfaces of any description over 10cm girth or width, and applying two coat of synthetic enamel paint (camouflage pattern), complete all as specified.

S&F in replacement 1.25mm thickness of laths of steel rolling shutters of gear operated type with bevel gear box and crank handle without ball bearing as specified including top cover anchoring rod hasp and staple and one shop coat of primer erected in position as indicated complete all as specified and directed by Engineer-in-Charge.

Taking down existing broken/damaged aluminium conductor strip of any size from wall/roof, complete all as specified.

S&F aluminium strip 25mm x 3.15mm, with saddle and screws for fixing the strip, complete all as specified.

Taking down existing broken/damaged copper conductor strip of any size from wall/roof, complete all as specified.

S&F copper strip 20mm x 3.15mm, with saddle and screws for fixing the strip, complete all as specified.

S&F in replacement Air termination, single pointed aluminium rod 12mm dia and 300mm long including screws for fitting, complete all as specified.

S&F in replacement Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hexagonal head screw, complete all as specified.

M&L Cement concrete (1:2:4) type B-1 (20 mm graded stone aggregate) as in block (450mm x450mm x300mm) for holding GI pipe post for air terminal rod including form work,complete all as specified.

S&F Mild steel galvanised pipe, light grade, 40 mm nominal bore fixed as termination post, fixed to poles/laid under floor/road crossing/walls complete with and including clamps socket & elbow etc complete all as specified.

M& L Earthing complete, all as shown on electrical plate No 5 of MES schedule part-I and as specified, including the following :-(i) copper earth plate of size 60cmsx60cmsx3.15mm thick buried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth not less than 1.50 metre below normal ground level.(ii) Earth plate surrounded by and packed with char-coal and common salt in alternative layers (n.exc 15cms each layer).(iii) copper strip 20mmx3mm earth wire from earth plate to main switch board including necessary GI bolts, nuts check nuts, washers, thimbles etc.(iv) 50 mm bore light grade, GI pipe for protection to earth-strip.(v) 20mm bore, medium grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horizontally to the earth pit. (vi) PCC chamber in cement concrete (1:3:6) type C-2 using 20mm graded stone aggregate and CI cover with frame (vii) Excavation in soft/loose soil, returning filling & removal of surplus soil to a distance upto 50 metre as directed. Note:- (i) Outer edge of earth pit will be 1.50 metre away from the outer edge of PCC chamber. (ii) copper strip upto test point is included in this item. (iii) water pipe shall be provided in slantling position.

A N CONSTRUCTION CO

PREM CONSTRUCTION COMPANY

JAY ANN CONSTRUCTION COMPANY