AS AS TO KITCHEN OF BUILDING NO P-22(CHOLA SUITE) AND PROVISION OF 2 NOS OF TOILETS NEAR SPORTS GROUND AT INS CIRCARS ,SPECIAL REPAIRS TO LADIES AND GENTS TOILET AT 6 TH FLOOR OF HQ ENC BUILDING P-45 AT NAVAL BASE VISAKHAPATNAM AND SPECIAL REPAIR TO

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surface 350 x 250 x 7 mm/ 450 x 350 x 7 mm thick (Concept pattern Tiles) set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (Square/ Rectangular) polished, light shade, area of each tile exc 0.11 sqm but not exceeding 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness, (Below or above ground level) complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar and removing rubbish upto a distance outside MD land complete all as directed by the Engr-in-Charge.

M&L for 25 mm thick PCC 1:2:4 type B0 (Using 12.5 mm graded stone aggregate) in sub base of floorings finishing the cement concrete surfaces even and fair complete all as specified and directed.

M & L for Plain cement concrete 1:5:10, type E-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

Disamntling post or struts any section, RCC or steel any type including taking out embedded portion in concrete and making good disturbed ground complete all as specified and directed.

M&L for Plain Cement Concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M & L for hardcore of gauge n.exc 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for sand filling under floors or in foundations,sand cushioning for cable laying in trenches etc including spreading, levelling, watering and consolidation complete all as specified and directed.

M&L for 100 mm thick cement concrete 1:2:4 type B- 2 using 40 mm grade aggregate as in base of flooring/hard standing, etc, and finishing the cement concrete surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for Vitrified, designed, light shade coloured tiles, 10 mm thick, (square/rectangular) polished, area of each tiles not exc 0.42 sqm but not exc 1.00 sqm, in floors, etc including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M&L for Vitrified, designed, light shade coloured tiles 10 mm thick (Square/ Rectangular) polished, light shade, area of each tile exc 0.42 sqm but not exceeding 1.00 sqm, in skirting/Dado set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 10mm thick plaster in CM 1:4 complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises, where directed and leaving the work clear complete all as specified and directed.

M & L for 15 mm thick rendering in two coats (10mm+5mm Each) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with integral water proofing compound with weight of cement in top layer as per manufacturer's instructions and finished the surface even and fair without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

Supply only integral water proofing compound [ISI marked] of approved make complete all as specified and directed.

M&L for 5 mm thick rendering in CM 1:3 on concrete surfaces as in ceiling/ chajja finished fair and even without using extra cement complete all as specified and as directed.

M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and fair without using extra cement complete all as specified and directed.

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, pillars etc and disposal of debris and rubbish to a distance n.exe 100 m as directed by the Engr-in-Charge.

M&L brick work with fly ash bricks, bricks, straight or curved on plan to any radius as in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L for Brick work with fly ash Bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as Specified and directed

M & L for 18 to 20mm thick Granite (of any type) work (table rubbed and polished) in floors, steps, jambs, pillars, window-cills, cooking platforms and like bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15 mm thick screed bed in cement mortar 1:6 & cutting, polishing complete all as specified and directed.

M & L for granite stone slab (of any type) as in vertical surfaces such as skirting/dado etc, 18 to 20 mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 10 mm thick screed bed in cement mortor 1:4 & cutting, polishing complete all as specified and directed.

M&L for excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n. exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Use and waste of form work to soffits of suspended slabs such as roof slabs, n. exc. 20cm thick (horizontal or sloping for fair finished concrete surface complete all as specified and directed.

M&L for RCC M-30 (Design mix) using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and the like etc complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves ,plinth beam including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for RCC M-30 (Design mix) using 20mm graded crushed stone aggregate as in lintels beams and roof beams etc complete all as specified and directed

S & F high strength corrosion resistant TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

S & F high strength corrosion resistant TMT bars 5mm dia and over upto and including 10mm dia in strirrups, spacers and binders spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed.

M&L for hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75 mm thick Cement concrete 1:3:6 type C1(using 20 mm graded stone aggregate) in plinth protection, and finishing the concrete surface even and smooth without using extra cement including making joints filled with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4 as in retaining walls, abutments and similar work complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

Removing excavated material not exc. 1.5 Km but nexc 5.00 Km and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M & L for preparation of the sunken floor surfaces by mechanical abrading to remove all loose mortar and laitance, oil, grease etc and washing with plenty of water, making the surfaces sound and free from cracks by cutting 'V' grooves cut along the cracks and filling with single component polymer modified repair mortar and carrying initial pond test for 24 hours to identify any invisible cracks, injection grouting for cracks on negative side of the surface using plasticized expanding grout admixture @ 250 gms/50 Kg bag of cement with neat cement slurry by drilling the hole of 12mm dia and fixing the nozzles using single component instant leak plugging compound along the construction joints, cracks etc at a distance of not more than 500mm angle fillet, providing a cement sand mortar based fillet of 50x50mm admixed with high performance acrylic emulsion based binder @ 0.25 Litre per 50 Kg of cement all around in the side at the floor and wall junction and curing by water as per standard practice, applying two component elestomeric acrylic polymer modified cementitous water proofing coating . The mixing ratio of the coating shall be 2 parts of powder and 1 part of liquid without any water addition in the mixing complete all as per the manufacturer's instruction at a consumption factor of 1.5Kg/Sqm in two coats complete all as specified and as directed. Make of chemical:- (a) Single component polymer modified repair mortar :- SMARTCARE of Asian Paints or equivelant of STP/Fosroc (b) Plasticized expanding grout admixture :- SMARTCARE Injection Grout Additive for cement of Asian Paints or equivelant of STP/Fosroc (c) Single component instant leak plugging compound : - SMARTCARE Instant Leak Stop of Asian Paints or equivelant of STP/Fosroc (d) High performance acrylic emulsion based binder : -SmartCare Multi-purpose Polymer of Asian Paints or equivelant of STP/Fosroc (e) Elestomeric acrylic polymer modified cementitous water proofing coating :- Smart Care Damp Block 2K Suprema of Asian Paint or equivelant as approved

M & L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces mixed with an integral liquid waterproofing compound as admixture @ 100ml per bag of cement finished the surface rough complete all as specified and as directed. Make : SMARTCARE Vitalia of Asian Paint or equivalent product of Dr Fixit,Sika,Dulax

M & L for treatment around the pipes of any dia passing through walls (Core cut area) by wrapping around all the pipes with acrylic emulsion based binder and placed appropriately in the same position and the gaps between the pipe and the core cutting shall be grouted by using high strength, non- shrink cementitious grout complete all as per the manufacturer's instruction and as directed. Make of chemical: APL Smart care (Asian Paints) or equivelant of STP/Fosroc

M&L for preparation of old decorated surface by complete removal of existing treatment, washing, rubbing, stopping etc and applying two coats of oil bound washable distemper over a coat of primer including applying one or more coat of wall care putty to a smooth surface including making good any undulations on the surfaces complete all as specified and as directed. Note :- (i) Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS (ii) Sanding of surfaces shall be done by mechanical sander with 1500-2700 rpm with internal dust extraction system for clean environment certified by the Paint manufacturer)

M&L for preparation of old decorated surface by complete removal of existing treatment from ceiling, washing, rubbing, stopping etc and applying two coats of oil bound washable distemper over a coat of primer including applying 3 mm thick wall care putty to a smooth surface including making good any undulations on the surfaces complete all as specified and as directed. Note :- (i) Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS (ii) Sanding of surfaces shall be done by mechanical sander with 1500-2700 rpm with internal dust extraction system for clean environment certified by the Paint manufacturer)

M & L for preparation of new ceiling surfaces and applying three coats of white wash complete all as specified and directed.

Taking down chowkats or frames with shutters exceeding 1.5 Sqm Each but n.exc 4 sqm Each (Without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames with shutters not exceeding 1.5 Sq. m Each (Without taking off shutters from the frames) complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full Body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm 2 , modules of elasticity 900 N/mm 2 and resistance to spread of flame of Class A category with water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full Body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm 2 , modules of elasticity 900 N/mm 2 and resistance to spread of flame of Class A category with water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F 30mm thick Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive trength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body hreaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges with S S screws shall be paid separately) complete all as specified and directed.

M & L for 18mm thick, factory made ready to install, Non-toxic, Lead & Cadmium free, single extruded, water proof, termite proof, fire retardent, excellent screw holding capacity, solid PVC board, one side decorative choice lamination and other side balancing white as in cupboard shutter, fixed to door frame with and including continuous Piano hinges of stainless steel, bright finish or Electrogalvanised and width of flaps 40mm (when open) and stainless steel screw including lipping the cut edges with same materials finish complete all as specified and directed.

M & L for 18mm thick, factory made ready to install, Non-toxic, Lead & Cadmium free, single extruded, water proof, termite proof, fire retardent, excellent screw holding capacity, solid PVC board, one side decorative choice lamination and other side balancing white as in cupboard shelves fixed to and including PVC guide rail and stainless steel screw including lipping the cut edges with same materials finish complete all as specified and directed.

S & F 300 mm size, stainless steel designer pull handle, fabricated type polished complete all as specified and directed.

S&F in repair stainlesss steel wire basket (cutlery basket) pull out type, of size 535 mm x 510 mm x100 mm Grade 304 with necessary fixing clips etc complete all as specified and directed. Note- Work shall be carried out as per manufacture's instructions

S&F in repairs stainlesss steel wire basket (cup and saucer basket)pull out type, of size 535 mm x 510 mm x100 mm Grade 304 with necessary fixing clips etc complete all as specified and directed. Note- Work shall be carried out as per manufacture's instructions

S&F in repairs stainlesss steel wire basket (thali basket) pull out type, of size 535 mm x 510 mm x200 mm Grade 304 with necessary fixing clips etc, of make- Godrej or equivalent complete all as specified and directed. Note- Work shall be carried out as per manufacture's instructions

S&F in repairs stainlesss steel wire basket (plain basket) pull out type, of size 535 mm x 510 mm x200 mm Grade 304 with necessary fixing clips etc complete all as specified and directed. Note- Work shall be carried out as per manufacture's instructions

S&F in repairs stainlesss steel wire basket (plain basket) bottle pull out type, of size 535 mm x 510 mm x200 mm Grade 304 with necessary fixing clips etc complete all as specified and directed. Note- Work shall be carried out as per manufacture's instructions

S & F in repairs stainlesss steel wire basket (Grain basket) pull out type, of size 535 mm x 510 mm x200 mm Grade 304 with necessary fixing clips etc, complete all as specified and directed. Note- Work shall be carried out as per manufacture's instructions

S & F in repairs stainlesss steel pantry unit, of size 450 mm x 500 mm x 1800 mm Grade 304 with necessary fixing clips etc, including all accessories complete all as specified and directed. Note- Work shall be carried out as per manufacture's instructions

S & F in repairs stainless steel sliding / telescopic channel of length 20 inch (500 mm) with 3 nos of holding ball of load carrying capacity 45-50 kg of 202 grade steel , width 45 mm including necessary fixing arrangement complete all as specified and directed.

S & F repairs cold rolled nickel plated steel O crank soft closing concealed hinge (12-15 mm) including necessary fixing arrangement to shutter complete all as specified and directed.

S & F in repairs stainless steel ventilator of size 100 mm x 100 mm for cupboard shutter including necessary fixing arrangement to shutter complete all as specified and directed.

S & F in repairs stainless steel modular kitchen handle, 100 mm long complete all as specified and directed.

M&L for 18 mm thick factory made ready to install, non toxic , lead & cadmium free, single extruded, water proof, fire retardent and with excellent screw holding capacity , solid HDHMR board , one side decorative acrylic choice lamination and other side balancing white as in cupboard shutter , fixed to door frame with bright finish or electrogalvanised and width of flasp 40 mm (when open) and stainless steel including liping the cut edges with same material finish complete all as specified and directed.

S&F repair polycarbonate sheet 10 mm thick (of any pattern) in nature with material properties relevant to IS for roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed

S & F mild steel bands, straps, supports or stays of rain water, ventilating pipes including bolts, hooks (stay) for large gates, hook and pintel hinges, clamps, hold fasts, wall ties, flat iron fillets for securing wire mesh, wind tie, fan hook and similar work including necessary drilling bolting or riveting etc conforming to Fe – 290 Gde E – 165 complete all as specified and as directed.

S & F 125mm Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and directed.

S & F 100 mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 150mm Long extruded brass handles fabricated type polished complete all as specified and directed

S&F 200 mm long, Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts complete all as specified and directed.

S & F, 4 lever, 16.3 x5.3x 3.2 cm ,Brass, floor latch lock bolt ground lock , heavy duty complete all as specified and directed.

S&F 200 mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed

S&F 300mm long,designer brass sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts complete all as specified and directed.

S&F door clooser aluminium body hydraulically regulated , designation No.2 , universal type , suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F Floor door stopper, 140 mm overall length of cover plate, brass body and tongue with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F 18/19mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work complete all as specified and directed.

S&F 75 mm long medium weight, stainless steel butt hinges auto cabinet self closing type complete all as specified and as directed

S&F magnetic catches of superior quality, plastic body and striking plate for cupboard shutters complete all as specified and as directed.

S&F 200 mm long,stainless steel designer handle, fabricated type polished complete all as specified and directed.

S&F 0.90 mm thick decorative lamination type - I as per approved colour and pattern shall be fixed with adhesive as per manufacturer's instruction complete all as specified and directed.

Supply, materials and application of two component structural grade polymer modified reinstatement mortar 20 mm thick of minimium compressive strength 12N/mm2 in 1 day and 45N/mm2 in 28 days. Minimum flexural strength should be 8 N/mm2 in 28 days. Single component acrylic polymer emulsion to be applied @ 6-8 sqm/lit before the application of modified polymer mortar .The morter shall be applied in layers n.exc 10mm thick in layers and including surface preparation ( maximum coverage area 1.3 sqm at 10 mm thikness per 25.25 kg bag ) Note:- This item shall be execution where shuttering is not possible or small patch repairs of structural elements . Make: (a) Acrylic polymer emulsion primer : Nitobond AR of FOSROC or equivalents solutions SIKA/STP/HINDCON as approved by GE. (b) Polymer modified reinstatement mortar:- Renderoc S2 of FOSROC or equivalents solutions SIKA/STP/HINDCON as approved by GE.

M&L for preparation of new platered surface of wall and applying two coats of weather proof 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre, dart pick up resistant,silicon enhanced,UV resistant and PU enhanced property over a coat of alkali resistant primer including applying one or more coat of wall care putty to a smooth surface including making good any undulations on the surfaces including all necessary scaffolding,complete all as specified and directed. Note :- Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS

M & L for preparation of new ceiling surfaces and applying two coats of distemper oil emulsion over a coat alkali resistant primer over a coat of of wall care putty complete all as specified and directed.

Demolition of reinforced Cement Concrete of any description and in floor and roofs (other than ground floor), and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100 M complete all as specified and directed.

M&L for cement concrete (1:2:4), type B1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary formwork complete all as specified and as directed.

S&F Mild steel TMT bars 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S & F Towel Ring Square with Round Flange including Chromium plated brass screws and wooden/plastic cleats etc complete all as specified and directed. Make: Jaquar Cat No. ACN-1121N or equivelant of make as per list of manufacturer mentioned in PS.

All as per item no 90 but S&F in repair

S & F CP Towel rack 600 mm long with lower hanger fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) as specified and as directed by Engr-in-charge. Make: Jaquar Cat No. AKP-35781PS or equivelant of make as per list of manufacturer's

All as per item no 92 but S&F in repair

S&F CP health faucet with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hooks complete all as specified and directed. Make: Jaquar Cat No. ALD-565 or equivelant of make as per List of manufacturer's

All as per item no 94 but S&F in repair

S&F 15 mm bore 2 in 1 bib cock, chromium plated with wall flanges complete all as specified and directed. Make: Jaquar Cat No. FLR-5041N or equivelant of make as per List of manufacturer's

All as per item no 96 but S&F in repair

S&F Toilet paper holder with with flap recessed type, , chromium plated fixed to wall with brass screw complete all as specified and directed Make: Jaquar Cat No. AHS-1553 or equivelant of make as per List of manufacturer's

All as per item no 98 but S&F in repair

S&F 15 mm bore, angular stop cock with wall flange, cast copper alloy, chromium plated, fancy type, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make: Jaquar Cat No. KUP-35053PM or equivelant of make as per List of manufacturer's

All as per item no 100 but S&F in repair

S&F in repair single towel rail 600mm long,stainless steel complete all as specified and directed. Make: Jaquar Cat No. ACN-1111SM or equivelant of make as per List of manufacturer's

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs, 15mm bore, chromium plated bib cock with wall flange, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make: Jaquar Cat No. FLR-5047N or equivelant of make as per List of manufacturer's

S & F Soap Dish Holder, fixed in walls with plugs & chromium plated brass screws complete all as specified and directed. Make: Jaquar Cat No. ACN-1131N or equivelant of make as per List of manufacturer's

S & F 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. Make : Jaquar Cat No.CON-011KN or equivelant of make as per list of manufacturer's

S & F in repairs Vitreous China Rimless Single Piece WC with UF soft close slim seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern Fittings, Size: 380x725x690 mm, S Trap - 300 mm and all fittings and fixtures including connection to outgoing drain including making good damaged/disturbed surfaces complete all as specified and directed. Make: Jaquar Cat No. ONS-WHT-10853S300UFSM or equivelant model of make as per list of manufacturer mentioned in PS.

S & F in repair Vitreous China Table Top Basin, Oval Shape of Size: 640x425x155 mm excluding taps fixed on granite slab complete all as specified and directed. Make : Jaquar Cat No. JDS-WHT-25901 or equivelant model of make as per list of manufacturer mentioned in PS.

S&F vitreous China wash hand basin table top thin rim white coloured, rectangular shape, of size : 495x395x150 mm including cutting for and pinning in ends of brackets or making suitable size of hole for pillar tap in RCC slab and granite hole complete all as specified and directed Make: Jaquar Cat No. JDS-WHT-25909 or equivelant of make as per List of manufacturer's

S&F in repairs 15 mm bore CP mixer single lever tall boy with 125mm Extension Body Fixed Spout without popup waste system with 600mm long braided hoses complete all as specified and as directed. Make: Jaquar Cat No. ALI-85005B or equivelant of make as per List of manufacturer's

S & F in repairs Vitreous China urinal, with all Fixing Accessories Set without sensor, of Size 480x300x740mm, Starwhite with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete complete as specified and directed. (Make: Jaquar Cat No. URS-WHT-13255 or equivelant of make as per list of manufacturer's)

S&F in repairs full height urinal partition with 8 mm thick frosted glass ,chrome finish ,size - 1950mm(H)x 600 mm(W) complete all as specified and directed. (Make: Jaquar Cat No. JSE-CHR-810UF60H19X or equivelant of make as per list of manufacturer's)

S & F vitreous China wash down water closet pan (pedestal pattern) of size 350x480x395 mm white, including connection to outgoing drain and flushing pipe, anti syphonic pipe, P or S trap with PVC water closet seat cover, black or white or coloured ,closed pattern with flat bottom and mild steel chromium plated hinging device complete but excluding flushing cistern & flush pipe including making good damaged/disturbed surfaces complete all as specified and directed.

S & F 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and directed.

S&F regular sink mixer with swinging Spout (Table Mounted Model) with 450mm long braided hoses complete all as specified and directed. (Make: Cat No. CON-309KNBM of Jaquar or equivalent model from make list as given here-in-after.)

S & F stainless steel kitchen sinks with double bowl made of 1 mm thick sheet ,gloss finish for kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 940 mmX460 mmX203 mm and bowl size 354 mmX406 mmX203mm complete all as specified and directed.

S&F PVC waste pipe 32 mm bore and 800mm long complete all as specified and directed.

All as per item no 117 but S&F in repair

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

All as per item no 119 but S&F in repair

S&F PVC (SWR) Floor trap of 110 mm dia., outlet with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair PVC (SWR) Floor trap of 75 mm dia., outlet with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair PVC (SWR) multi Floor trap of 75 mm dia.,outlet with grating including jointing with solvent cement complete all as specified and directed.

Supply, laying, connection and testing in repair, 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

S&F 32 mm outer dia ,CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S & F in repair 20 mm bore, gun metal, globe or Gate valves with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed.

S & F in repair 32 mm bore, gun metal, globe or Gate valves with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc complete all as directed.

S&F 110mm bore PVC (SWR) pipes single socketed Soil waste and vent pipes in any length with or without ears with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed Soil waste and vent pipes in any length with or without ears with rubber ring joints laid in trenchs complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed Soil waste and vent pipes in any length with or without ears with rubber ring joints laid in trenchs complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed Soil waste and vent pipes in any length with or without ears with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius with access doors complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius complete all as specified and directed.

S & F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal complete all as specified and directed.

S & F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access doors complete all as specified and directed.

S & F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access doors complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F PVC (SWR) gully trap of 125/110 mm dia., outlet with grating including jointing with solvent cement complete all as specified and directed.

S & F Second class hard wood plain, solid, straight Chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint complete all as specified and directed.

S & F 30 mm thick, factory made Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F 35 mm thick, factory made, glazed/skeleton shutters with second class hard wood,open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass, etc complete as specified and directed . Sizes of members of shutters as specified in SSR Part I, clause 8.24 (a) complete all as specified and directed

M&L for 4mm thick veneered decorative plywood, grade1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber complete all as specified and directed.

M & L for preparation of old painted wooden surfaces of any description n.exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc primer complete all as specified and as directed.

S & F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for 40 mm thick DPC in PCC 1:2:4 type B0 using 12.5 mm graded aggregate mixed with water proofing compound as per manufacturer instruction as in horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

S&F factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). (Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.)

S & F 4.8 mm thick, figured glass, pin head type and glazing with oil putty/ aluminium beading in squares exc 0.5 sq. m in each pane complete all as specified and as directed.

S & F 5.5 mm thick, tinted/figured sheet glass, ordinary quality and glazing with rubber beading in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete as per specification and drawing and as directed.

S&F factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed

S&F 125 mm long extruded aluminium alloy anodised Butt hinges with galvanized mild steel hinge pin type B 22 complete all as specified and directed .

S&F 200 mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed

S&F 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

Material and labour for preparation of horizontal or vertical surfaces for water proofing treatment on existing cleaned non accessible RCC roof with the following specification and manufacturings instruction complete all as specified and as directed:- (a) Preparing and cleaning of fully dry surfaces as per IS3067-1966 (b) Applying bitumen primer(85/25 grade)conforming to IS:3384-1968 over the cleaned plaster surface @ 0.5 Ltr per sqm by the same membrane manufacturer of density at 25°C, 0.87 to 0.89 kg / Liter and viscosity 70-160 cps shall be applied on the prepared surface. (c) Applying a layer of APP based polymeric membrance 3.0mm thick (minimum) weight 3.6Kg per sqm (reinforced) with polyster Non woven fabric weighing not less than 160gms per sqm by torch application. The over laps shall be minimum 100mm on the transverse direction and 75 mm on longitudinal direction. (d) Applying one coat of aluminium paint @0.10 ltr per sqm over APP based polymeric membrane.

S & F Vitreous China bowl urinal flat back, of size 465x355x265mm, white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete complete as specified and directed.

Supply, laying, connection and testing, 15mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

Supply, laying, connection and testing, 20mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

M & L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, coloured / multicoloured, glossy finish , set, jointed and pointed white cement slurry and pigments in floors, etc including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks, double layer construction, ISI marked (Cylindrical vertical with closed top), hoisted and fixed in position as specified in SSR Part I complete all as specified and directed.

S&F 20 mm dia PTMT ball valves, high pressure, with polythene float and fly nut , screwed for Iron pipe or brass ferrule complete all as specified and directed.

S & F 150 mm size, stainless steel designer handle, fabricated type polished complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, 40mm width of flape when open complete all as specified and directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 mixed with water proofing compound and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for Precast Reinforced Cement Concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab (For manhole etc), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and set in cement mortar 1:4 including necessary form, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measured and paid separately)

M & L Reinforced concrete pipes, class NP2, 150 mm bore, laid and jointed with collars complete all as specified and as directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggragate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore RCC drain pipes complete all as specified and directed

M & L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required for 150 mm bore of pipe complete all as specifieed and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness including cover fillets/snap grid/frame work etc complete all as specified and directed.

S & F Gl frame work for seamless ceiling in two layers comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed.

Providing and fixing Gypsum Board, 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed.

S & F designer cornices mouilding suitable for seamless ceiling board not less than 75mm wide or as per the manufacture's instructions complete all as specified and directed.

Supply, laying, connection and testing, 25 mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixed complete laid in trenches, etc complete all as specified and directed.

S & F 25 mm bore, gun metal, globe or Gate valves with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed.

Cutting the existing GI/DI pipe line of 50 mm dia for alterations or additions necessairly done in position without taking down and inserting Tee of 50x50x25 mm with collars and required specials for tapping including necessary earth work complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as directed

Taking down unserviceable main switches, DBs, bus bars chambers any capacity including all fittings and fixtures such as MCBs, isolator, etc and removing from site complete all as specified and directed.

Taking down unserviceable sub-main wiring (any numbers of cable) with rigid steel conduits/PVC casing-caping including cutting chases for conduits and making good disturbed surfaces complete all as specified and directed.

M & L for conceled Point wiring with two runs of single core 1.5 Sq.mm. (Nominal area) PVC insulated unsheathed multistranded copper conductor cable FRLSH (ISI marked) drawn through and including non metallic PVC conduit 20 mm bore (Minimum) medium grade (ISI marked) concealed type including metal GI boxes of suitable module including modular white cover plate of suitable module for fixing modular type switches, sockets, regulators etc. including provision of multistranded 1.5 Sq.mm copper conductor cable FRLSH [ISI marked] as earth wire connected to common earth dolly and earth in distribution board complete all as specified and as directed, for one light/exhaust fan/fan point/call bell controlled by one way switch. (Note.: (i) The rate quoted is deemed to include making good the disturbed sufaces and to match the adjoining surface. (ii) The quoted rate is deemed to include cutting chases for concealed wiring including making good the same as per the existing one)

All as per item No.184 above but for One 3/5 pin socket outlet 6 amps on independent board complete ditto

All as per item No. 184 above but for One 3/5 pin socket outlet 6 amps point on same board complete ditto

All as per item No 184 here in before but for one 15 Amps power point on the independent board with two runs of PVC insulated and unsheathed copper conductor cable of size 2.5 sqmm multistranded FRLSH (ISI marked) and 2.5 sqmm PVC insulated unsheathed solid copper conductor cable FRLSH (ISI marked) as earth lead complete ditto

S & F switch modular single pole one way 6 amp 240 volts,1 Module complete all as specified and as directed.

S & F Modular socket outlet 6A, 2/3 pin combined, 2 module, AC 230V, 50HZ complete all as specified and as directed.

S & F switch modular single pole one way 16 amp 240 volts,1 Module complete all as specified and as directed.

S & F Modular socket outlet 6A/16A, 2/3 pin combined, 2 module, AC 230V, 50HZ complete all as specified and as directed.

S&F ceiling rose, 65 X 50mm two to three terminals, PVC / polycarbonate, insolated body complete all as specified and directed.

S&F LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible,copper conductor cable of suitable size from ceiling rose complete,including taking down existing tube light fitting of any type and making good to the disturbed surface to match with existing complete all as specified and as directed

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete,including taking down existing tube light fitting of any type and making good to the disturbed surface to match with existing complete all as specified and as directed

S & F LED downlight, Recess mounted square, die cast aluminium housing, 15 Watt as per the existing cutout, 160-180mm and making flush and smooth with gypsum board, CCT: WW/NW/CW, CRI > 80 Ra, IP 20 rated, with open and short circuit protections as per IS: 10322 with all accessories and connecting up with twin core twisted copper conductor cable of suitable size including lamp complete all as specified and directed.

Supply and fixing LED light fitting 1 x 9 W / 1 x 10 W, bulk head luminaires including LED light driver, holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

M & L for Sub main wiring with 2 runs of Single core 4.0 sqmm [ for Phase & Neutral ] PVC insulated multi stranded FRLSH (ISI marked) copper cable drawn through and including concealed PVC conduit of suitable size (medium grade) with all conduit accesories and fittings along with 1 run of single core 4.0 sqmm PVC insulated multi stranded FRLSH (ISI marked) copper cable as earth continuity conductor complete all as specified and as directed. (Note :- (i) Two runs of 4.0 sqmm and one runs of 4.0 sqmm cable as earth wire and one run of conduit shall be measured as one length, (ii) The quoted rate is deemed to include cutting chases for concealed wiring including making good the same as per the existing one)

S&F Distribution Board, SPN 4 Way, 240V, Double door with IP 43 protection IK 09 complete all as specified and as directed.

S&F Distribution Board, SPN 8 Way, 240V, Double door with IP 43 protection IK 09 complete all as specified and as directed.

Supply, fixing, commissioning and testing in repairs MCB SPN 6-32 Amps, 240 Volts, 10KA, C curve complete all as specified and as directed

Supply, fixing, commissioning and testing MCB SP 6 to 32 Amps, 240 Volts, 10KA, C Curve, complete all as specified and as directed

Taking down & dismantling the Exhaust fans from its position for cleaning, servicing, oiling and lubricating and replacement of unserviceable parts and refixing the same after painting Exhaust fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. complete with all the parts i.e. frame,fan legs, fan blades etc. damaged spilt pins and screw, nuts and spring washers including ,flexible cord of 24/0.2mm with nece.ary connector as required complete all as directed. Note : The cost of new parts require for minor repair work shall deemed to be included in quoted rate

S&F exhaust fan 300 mm size, steel body suitable for operation on single phase 240 V AC, 50 Hz and including connecting up with twin core PVC insulated , sheathed flexible copper conductor cable of size 1.50 sqmm including making good disturbed surfaces to match with surronding complete all as specified and directed.

Supply and fixing staitionary louvers suitable for exhaust fan 300 mm size, made out of powder coated aluminium sheet of minimum 1mm thick with non removable blades fixed parmanently at 45 degree angle for protection from rain including aluminium wire mesh of suitable size for bird control complete all as specified and directed.

Supply and fixing vertical electric water heater, storage type, shock resistant steel body, high quality steel inner tank with glasslined Coated with high density PUF insulation, fitted With specially designed acrificial magnesium anode to prevent corrosion due to hard water ,100% copper heating element upto 2 KW, 230 volts, capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, 4 nos fixing bolt of suitable size including nuts and washer etc,2 nos PVC connection pipe and making the electrical connection with and including 16A Plug Top including testing after installation complete all as specified and directed. Make:- Crompton , Havells, Racold , Bajaj,V-Guard Note : Contractor Shall submit manufacturer test report as per BIS before payment.

M & L Earthing complete with GI earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected with galvanised earth lead of 4.00mm dia by means of bolts, nuts, check nuts and washers protected by 15mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, with 40 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 10 cm C/C both ways and suitable handle of 12 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel, wire mesh, aluminium lugs, complete in all respect all as shown in electrical plate No. 3 and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion complete all as specified and as directed by the Engineer-in-Charge. Note: On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost

Supply and laying cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 Sqmm , 2 core laid in trenches or fixed to wall / pole with necessary fixing clips complete all as specified and directed.

S&F un- reinforced precast concrete cable cover, class LV, type 1 flat of size 250mm x 150mm x 40mm complete all as specified and directed.

P SRINIVASA RAO (BID ID -3450195)

G Srinivas Rao (BID ID -3448378)

SATYAMEGHA ENGINEERS (BID ID -3450276)

LALITHA SAI INFRA (BID ID -3449613)

Eastern engineering Enterprises (BID ID -3451387)

Jessica Engineering Works (BID ID -3450321)

K.ADITYA ENGINEERING CONTRACTORS (BID ID -3449199)