REPAIRS MAINT AND POLISHING PAINTING TO CERTAIN WOODEN STEEL FURNITURE OF NASA CERA SAILORS IN LIVING AREA NAVJIVANI AND OTHER MISC BUILDINGS AMBC INS ZAMORIN AND OTHER TRG AREAS AT INA EZHIMALA

Amount

CHAIR DINING (DRG NO. PMA(K)/GPI/HW/03)

Removing unserviceable front leg and supply and fix new leg as existing made out of well seasoned HW (teak wood) all as per drg size 433x55x30mm.

Removing unserviceable back leg and supply and fix new leg as existing made out of wellseasoned HW (teak wood) all as per drg size 855x55x30mm.

S&F new rubber shoes superior quality 4 Nos each to chair.

TEAPOY (DRG NO. PMA(K)/GP-1/HW/12)

Removing unserviceable top and S&F new top made out of prelaminated prticle board exterior grade, edge shall be covered with 4mm thick teak wood beeding as existing. Rest all as per drawing size 600mmx450mmx18mm/19mm thick, Make: Ecoboard/Novopan

Removing unserviceable side rail and S&F new side rail made out of well seasoned HW (teak wood) . Rest all as per drawing size 450mmx50mmx20mm thick ,ade pit of well seasoned hard wood teak

PEG TABLE (DRG NO. PMA(K)/GP-1/HW/12) Removing unserviceable top and S&F new top made out of prelaminated prticle board exterior grade of size 450mmx300mmx18mm thick with and including provisioning of 4mm thick teak wood beading all around to top

TABLE CENTRE (DRG NO. PMA(K)/GP-1/HW/17) Removing unserviceable top and S&F new top made out of prelaminated prticle board exterior grade , edge shall be covered with 4mm thick teak wood beeding as existing. Rest all as per drawing size 1000mmx500mmx18mm/19MM thickwith and including provisioning of 4mm thick teak wood beading all around to top

TABLE COMPUTER (DRG NO. PMA(K)/GPI/HW/01, PMA(K)/017)

Removing unserviceable sliding key board and S&F new boards shade & shape as existing made out of prelaminated particle board exterior grade.to match with existing shade and shape

Removing unserviceable sliding drawer and S&F new sliding drawer of existing shade of 18mm pre-laminated particular board including new rails and weels all as per drawing. All accessories from reputed manufacture in india / abroad .

Removing the twin wheel castrol and S&F new twin wheel castorol of injection moulded in 30% glass fitted back nylone

TABLE WRITING WITH DRAWER (DRG NO. PMA(K)/GP-1/HW/24)

Removing unserviceable top and S&F new top made out of prelaminated prticle board exterior grade , edge shall be covered with 4mm thick teak wood beeding as existing. Rest all as per drawing size 1220mmx810mmx18mm thick with and including provisioning of 4mm thick teak wood beading all around to top

Removing unserviceable bottom stiffner short from table writing S&F new bottom stiffner (Centre/long/side stiffner) made out of I class Hard wood(TW) existing size and shape for table writing all as specifed

Removing unserviceable bottom stiffner long from table writing S&F new bottom stiffner (Centre/long/side stiffner) made out of I class Hard wood(TW) existing size and shape for table writing all as specified

TABLE DINING 4 PERSONS (DRG NO. PMA(K)/GP-1/HW/20)

Removing unserviceable Table top, S&F new table top of size 1200x700xmm made out of marine plywood with sunmica lamination of 1mm thick on top. Teak wood beeding of size 45x20mm shall be provided all around, all wooden surface shall be finished with two coats of french polish. All are as shown on drg and directed by Engr in Charge

Removing unserviceable leg and S&F new leg of exisitng size and shape made out of well seasoned HW Teak wood. Rest all as per the drawing

CHAIR DINING WITH LONG BACK (DRG NO. PMA(K)/GP-1/HW/03)

Removing existing unserviceable worn out tapestry cloth from chair S&F of approved superior quality tapestry cloth as cover to PU foam seat of chair dining with long back, cost of tapestry cloth used shall not be less than 250/- per mtr.

Removing existing UNSV seat (Cushioned) from chair dining S&F of new seat of 12mm thick ply wood with PU foam of 50mm thick upholstery with fabric of approved shade and colour and not less than Rs 250/- mtr

STEEL FURNITURE ALMIRAH MEDIUM STEEL(DRG NO. PMK(K)/GP1/Steel/02)

Supply and fix 6 lever lock with duplicate key (2 Nos of key) of approved quality of existing size fixed with screw/welding to shutter of almirah including taking down of old lock.

Supply and fix MS handle chromium plated with necessary fittings of approved quality as shown on drg including taking down of old handles.

S &F new locking device as per drg including taking down of unserviceable locking device.

S&F shelves made out 1 mm thick MS sheet as existing including taking down of old shelves.

Removing dented/bend door shutter of Almirah steel Med and bringing the item to the original shape and re-fixing repaired door sutters with suitable hinges.

S&F leg made out of 1 mm MS sheet as existing including taking down of old leg.

Preparing the old painted steel surfaces by sand papering and applying synthetic enamel paint to give glossy finish all as directed by the Engineer-in-charge.

ALMIRAH LARGE STEEL(DRG NO. PMA(K)/44, FD-1031)

Supply and fix 6 lever lock with duplicate key (2 Nos of key) of approved quality of existing size fixed with screw/welding to shutter of almirah including taking down of old lock.

Supply and fix MS handle chromium plated with necessary fittings of approved quality Godrej pattern as shown on drg including taking down of old handle.

S &F new locking device as per drg including taking down of unserviceable locking device.

Supply and fix shelves made out 22 guage thick MS sheet to shape and size as shown on drawing and fixing with cleats, nuts and bolts including two coats of synthetic enamel paint over a coat of primer

Removing dented/bend door shutter of Almirah steel large/almirah large galzed and bringing the item to the original shape and re-fixing repaired door sutters with suitable hinges.

S&F leg made out of 1 mm thick guage MS sheet as existing size and shape including taking down of old leg.

Preparing the old painted steel surfaces by sand papering removing dents and bents filling with steel putty and applying synthetic enamel paint Olive Green colour to give glossy finish all as directed by the Engineer-in-charge.

BED HARD STEEL(DRG NO. FD/EZ/02/A/OMA, FD-246)

Removing eixsting worn out plywood top from bed,S&F 12mm thick Comercial plywood BWR Grade ( ISI marked ) fixed with S/S screw and cup washers as shown in drg size 1900x 900 mm

Removing unserviceable prelaminated particle board from head board of Bed hard. S&F new prelaminated particle board 18mm thick as existing (exterior grade ) in head board size of 664mmx200mm.

Removing unserviceable prelaminated particle board from leg board of Bed hard. S&F new prelaminated particle board 12mm thick as existing (exterior grade ) in leg board size of 664mmx300mm.

Preparing the old painted portion of Bed Hard steel surface by sand paper, removing dented and bends filling with steel putty and applying synthetic enamell paint black or existing colour to give glossy finish, all as directed by Engr in charge

CHAIR VARANDAH(DRG NO. FD/EZ/08)

Preparing the old painted steel surfaces by sand papering removing dents and bents filling with steel putty and applying synthetic enamel paint (usual brush painting) black colour to give glossy finish all as directed by the Engineer-in-charge

S&F new hard rubber shoe superior quality all as specified and directed by Engr-in-Charge

CHAIR CBA STAFF (DRG NO. PMA(K)/GP-1/STEEL/10)

Removing unserviceable tapestry cloth affixed to PU foam, from the Seat, supply and fix new tapestry cloth of superior quality as approved of size 420x420mm costing not less than Rs 220/- per mtr

Removing unserviceable tapestry cloth affixed to PU foam, from the Back, supply and fix new tapestry cloth of superior quality as approved of size 420x270mm costing not less than Rs 220/- per mtr

Preparing old steel surfaces by scraping with emery paper, cleaning, re-dusting, making the surfaces smooth and apply putty wherever required brush with two coats of synthetic enamel paint (Colour black) to given glossy finish

S&F hard rubber shoe of superior quality to bottom portion of legs

CHAIR EXECUTIVE(DRG NO. GP1/Steel/12, PMA(K)/015)

Removing exisitng unserviceable fabric from seat and back. S&F new fabric uphostery to moulded PU form of superior quality as approved by Engineer-in-charge

Removal of twin wheel casters and supply and fix twin wheel casters injection moulded

Removing existing broken pedestal assembly and S&F new fabric steel base all types revoling chair

Removing existing broken padded Arm rest for Revolving chair computer chair and S&F new Arm rest (Black integral) skin polyurethane inforced with MS insert it shall be scratch and wether resistant as per sample

CHAIR COMPUTER(DRG NO. PMA(K)/GP1/STEEL/11)

Removing exisitng unserviceable tapestry cloth from seat and back. S&F new tapestry of superior quality as approved by GE(cost of fabric shall not be less than 375/- per mtr)

Removal of twin wheel casters and supply and fix twin wheel casters injection moulded in 30% glass fitted back nylone.

Removing existing UNSV gas gift (up/down) and fixing the same gas gift to match with the existing the gas pressur of 300 N force , should under go an impact test from revoling chair , computer chair supply and fix new bottom gas lift (Hydraulic)

Removing existing broken pedestal assembly and S&F new fabric steel base all types revoling chair of make Godrej or equivalent

Removing existing broekn padded arm rest for revoiling chair ,computer chair and S&F new arm rest (black integral) skin polyurethene inforce with MS insert. It shall be scrarch and weather resistant as per sample

CHAIR CB STEEL(DRG NO. PMA(K)/GP4/06, GP1/STEEL/09)

Removing unserviceable tapestry cloth affixed to PU foam, from the seat, supply and fix as approved new tapestry cloth of superior quality of size 420x420mm costing not less than Rs 220/- per mtr.

Removing the unserviceable tapestry cloth affixed to PU foam, from the back, supply and fix as approved tapestry cloth of superior quality of size 420x270mm costing not less than Rs 220/- per mtr. Rest all as per existing

Removal of old unserviceable/broken/MS tubular pipe 25 mm dia from chair CB steel with/without arms and S & F 1.5mm thick 25mm tube welded to the legs/seat/back and arms as per standard Drg of steel furniture and all as specified and directed by Engineer-in-charge

Removing of old steel surfaces by scraping with emery paper, cleaning, re-dusting, making the surfaces smooth and apply putty wherever required brush with two costs of synthetic enamel paint ( colour black) to given glossy finish

S&F hard rubber shoes of superior quality bushes to bottom portion of legs.

CHAIR DESKLET TYPE-I(DRG NO. PMA(EZ)PW/01) Preparing old steel surfaces by scraping with emery paper, cleaning, re-dusting, making surfaces smooth and applying putty wherever required and applying two coats of synthetic enamel paint (colour black) to give glossy finish

DESK CUM BENCH THREE SEATER (DRG NO. PMA(K)/45, GP-1/Steel/21)

Removing unserviceable pre-laminated partical board top of desk and S&F top of desk made out of pre-laminated particleboard 18mm thick (Grade-I exterior grade) of existing shade (both side decorative teak veneer) of size 1650mmX365mm with and including provisioning of 4mm thick teakwood beading all around and applying french polish to the same.

Removing unserviceable pre-laminated partical board seat of bench and S&F new seat of bench made out of pre-laminted particle board 18mm thick (Grade-I exterior grade) of existing shade (both side decorative teak veneer) size 1650mmX365mm with and including provisioning of 4mm thick teakwood beading all around and applying french polish to the same.

Removing unserviceable pre-laminated partical board back of bench and S&F new back of bench made out of pre-laminted particle board 18mm thick (Grade-I exterior grade) of existing shade (both side decorative teak veneer) size 1650mmX365mm with and including provisioning of 4mm thick teakwood beading all around and applying french polish to the same.

Preparing old treated steel surfaces by scraping with emery paper, cleaning, redusting, applying steel putty whereever required, making surfaces smooth and applying two coats of synthetic enamel paint of existing colour over one coat of red oxide primer to give glossy finish

CABINET FILLING LARGE 4 DRAWER (DRG NO. PMA(K)/STEEL/06) Preparing the old painted portion of cabinet filling 4 drawar surface by sand paper removing dents and bents filling with steel putty and appling syntetic enamel paint smoke grey /or existing colour to give glossy finish all as directed by engineer -in -charge.

LOCKER FOR STAFF (6 PERSON) (DRG NO. PMA(K)PG5/STEEL/02) M&L for two coat of synthetic enamel paint of existing colour over a coat red oxide primer to give glossy finish over a putty as required including removal of old treated steel extrrnal sufrace by shaping with emery paper cleaning ,redusting making the surface smooth all as directed by engineer -in -charge.

RACK OPEN STEEL (DRG NO. PMA(K)GP-1/STEEL/33) Prepairing old painted steel surfaces by sand papering, removing dents and bents filling with steel putty and applying synthetic enamel paint smoke grey / existing of Rack,colour to give glossy finish all as directed by the Engr-in-Charge.

RACK SHOE STEEL (DRG NO. FD/EZ/06A, GP-1/STEEL/2) Preparing Old Steel Surfacs of inside and outside of Rack shoe steel open type with 05 Shelves by scraping with emery paper ,cleaning ,removing dirt and bends making surfaces smooth applying steel putty and applying two coasts of synthetic enemal paint of existing colour and shade of approved make and quality.

RIFLE RACK FOR 5.56MM INSAS (DRG NO. PMA(K)/GP1/HW/13) Prepaining old painted steel sufrace by sand paper.removing stains and filling bore holes crackes by putting wax and applying melamine polish matt finish to the exposed surfaces uniformly painted steel sufrace by sand paper.removing dents and bents filling with steel putty and applying one coat of synthetic enamel paint of existing coloure to give glossy finish

STOOL STEEL (DRG NO. PMA(K)/GP-1/STEEL-27) Prepairing the old painted portion of stool steel surface by sand paper . removing dents and bents fillling with steel putty and applying synthetic enamel paintsmoke grey / existing colour to give glossy finish all as directed by the Engr-in-Charge.

SIDE RACK 3 SPACE TRAY STEEL (DRG NO. PMA(K)/GP-1/STEEL-24) Prepairing old painted steel surfaces by sand papering, removing dents and bents filling with steel putty and applying synthetic enamel paint(useual brush Painting) smoke grey / existing colour to give glossy finish all as directed by the Engr-in-Charge.

TABLE OFFICE CLERK (DRG NO. FD-381, PMA(K)/GP-1/STEEL/33/32)

Removing the unserviceable table top and supply and fix new table top of size 1200x590mm made out of prelaminated particle board of 18mm thick existing shade one side of decorative veneer and other side off white (exterior grade) including 4mm thick teak wood edging duly (french polished all around as shown on drawing.

M&L for two coat of synthetic enamel paint of existing colour of approved shade including preparing old treated steel surface by cleaning with emery paper, redusting making the surface smooth and apply steel putty as required

Supply and fix steel lock 6 lever of approved quality with duplicate keys including taking down of old lock.

VISITOR CHAIR (DRG NO. PMA(K)02/03)

Removing unserviceable tapestry cloth affixed to PU foam, from the seat, supply and fix as approved new tapestry cloth of superior quality of size as per drawing, costing not less than Rs 220/- per meter

Removing unserviceable tapestry cloth affixed to PU foam, from the back and supply and fix as approved tapestry cloth of superior quality of size as per drawing costing not less than Rs 220/- per meter

Preparing old steel surfaces by scraping with emery paper, cleaning, re-dusting, making surfaces smooth and applying putty wherever required and applying two coats of synthetic enamel paint (colour black) to give glossy finish

POLISHING Prepare the existing surface of wooden surfaces by sand papering removing the stains and filling the bore holes, cracks by putting bees wax and apply polish Melamine matt finish (American wall nut colour) to the exposed surface uniformly complete all as directed by Engineer - in Charge.

Chair Dining (DRG NO. FD/EZ/01 & FD/EZ/01/OMA)

Teapoy(DRG NO.FD/EZ/383/OMA)

Peg Table(DRG NO.FD/EZ/12/OMA)

Table center(DRG NO.FD/EZ/MAP/11/OMA)

Hat Stand(DRG NO.PMA(K)/GP-45)

Work Bench(DRG NO.PMA(K)/GP-1/HW/01)

Book case(DRG NO.PMA(K)/GP-4/05)

Table dining 4 Pers(DRG NO.PMA(K)/GP-1/HW/20)

Table writing (DRG NO.PMA(K)/GP-3/02)

Table Bed Side(DRG NO.FD/EZ/MAP/18/OMA)

Table Dressing (L)(DRG NO.FD/EZ/14/OMA)

Chair Dining Long Back(DRG NO.PMA(K)/GP-1/HW/03)

Sofa Set 5 seater(DRG NO.PMA(K)/GP-1/HW/29)

Table computer 1 Seater(DRG NO.PMA(K)/GP-5/HW/02)

Notice Board(DRG NO.PMA(K)/GP-1/HW/11)

Chair Writing(DRG NO.PMA(K)/GP-1/PW/02)

Note:- The work includes for removing the furniture item from the existing accn/ office and shifting the same to the directed / specified area for the Repairs.

SAIRAM INDUSTRIES

Palace constructions