Work of item rate contract for Maintenance works routine / schedule / preventive / breakdown / overhauling of K.G. Khosla / Kirloskar make Air compressor with associated auxiliaries of Unit No. 3, 4 & 5 of Gandhinagar TPS, as & when required

Work of item rate contract for Maintenance works – routine /

TENDER schedule / preventive / breakdown / overhauling of K.G. Khosla /

Kirloskar make Air compressor with associated auxiliaries of Unit

No. 3, 4 & 5 of Gandhinagar TPS…as & when required

1 TENDER NOTICE

2 Important Notes to Bidders

3 BIDS FOR WORKS GENERAL CONDITONS

4 Other Terms & Conditions

5 General Terms & Conditions

BID - QUALIFICATION CRITERIA FOR TECHNICAL

TERMS & CONDITIONS, ANNEXURES & UNDER

TAKING (TO BE SIGNED BY THE TENDERER),

8 SCHEDULE – A, SCOPE OF WORK (ANNEXURE – A)

9 GENERAL SAFETY RULES

10 Terms and Conditions regarding Labour Laws

11 CONDITIONS OF CONTRACT

SCHEDULE “B” (PRICE BID TO BE SUBMITTED

EW-286 PUR-F-006 RFQ-

GSECL’s GST ID NUMBER: 24AAACG6864F1ZO

Work of item rate contract for Maintenance works – routine / schedule / preventive /

breakdown / overhauling of K.G. Khosla / Kirloskar make Air compressor with

associated auxiliaries of Unit No. 3, 4 & 5 of Gandhinagar TPS…as & when

CE [Generation], Gandhinagar, TPS invites “On-line Tenders” (e-tendering) for the work of

above subject item. Tender documents, Specifications and Terms & Conditions may be

down loaded from Web site https://tender.nprocure.com (For view, down load and on

line submission) and GUVNL / GSECL web sites www.gsecl.in (For view & down load

Bidders are advised to visit our above websites regularly up to opening of bid for any

corrigendum may be & submit corrected copy of tender (otherwise your offer will not be

considered for opening) & extension of due date.

All tender documents (Notarized / self-attested copies of original – as specified in tender

document) must be uploaded online on N PROCURE portal. EMD are to be submitted

physically by Registered Post A.D. or Speed Post addressed to: CHIEF ENGINEER

(GENERATION), GUJARAT STATE ELECTRICITY CORPORATION LTD, THERMAL POWER

STATION, GANDHINAGAR-382041, GUJARAT.

“NO COURIER SERVICE OR HAND DELIVERY” will be accepted.

Tender No. EW-286

Tender Fees + 18% GST Amount (Non-

Earnest Money Deposit Amount Rs.

Security Deposit As per clause no. 13 of ‘other Terms &

Time Limit for Completion of Work 24 Months from the Date of

Commencement of work order

Validity of the offers 180 days

Minimum Average annual turnover of

the bidder (for 03 years)

Years of past experience required for Completed Similar Works during Last

services/works 07 Years.

Last Date for Online tender / offer

submission through (n)Procure only up As per Tender Notice

to 18:00 Hrs (This is Mandatory)

Last Date for physical receipt of cover for

DD / Bank Guarantee / Online payment

reference for Tender Fee and EMD only As per Tender Notice

up to 15:00 Hrs Through RPAD or Speed

Date of opening of online Technical Bid,

all relevant documents submitted

through online process, Cover for Tender

fee and EMD at 15:30 Hrs (Online As per Tender Notice

technical bid will be opened for Bidders

who have submitted Cover for Tender

EW-286 PUR-F-006 RFQ-

Tentative date of on-line opening of price Party has to be in touch with website

bid (if possible) at 15.30 hrs. https://tender.nprocure.com and

also with e-mail sent by above website

Important Notes to Bidders:

(1) All the online Annexure and price bid, other tender documents (As per PQC)

must be submitted/attached through online form only. Bidder has to upload

scanned copies of original documents (Notarized / self-attested copies of original – as

specified in tender document) with bid. No physical documents to be submitted by

(2) Payment of Earnest Money Deposit (EMD):

All the bidders will be required to pay EMD as mentioned in the Tender Document

either in Demand Draft, Pay Order or Bank Guarantee (only for EMD) in favour of

Gujarat State Electricity Corporation Limited payable at Gandhinagar, Gujarat.

The scanned copy of original document shall have to be uploaded online with the bid

and RPAD or Speed Post only addressed to The Chief Engineer (G), Gujarat State

Electricity Corporation Limited, Thermal Power Station, Gandhinagar-382041.

(3) Being three part Bid, bidder shall have to submit their tender in three stages i.e.

PRILIMINARY STAGE (EMD Details- scan copy(online) & Original document- Hard

Copy submission), TECHNICAL STAGE (on line submission only) and COMMERCIAL

STAGE (on line submission only).

 First preliminary stage will be opened and if the documents submitted by bidder

towards payment of EMD are found ok, then only Technical Bid will be opened

(On-line). Tenders submitted without EMD by the firms, will be rejected without

entering into further correspondence. Submission of required documents for

exemption of EMD is mandatory.

 The exemption in payment of EMD shall be given to the,

1. Micro & small-scale enterprises which participate directly in tendering process

for the product which they are manufacturing / service which they are

providing and have Udyam registration for items / service under procurement.

2. Start-ups which participate directly in tendering process for the product

which they are manufacturing/service which they are providing and re-

cognized by DPIIT under the Start-up India Program and has obtained Udyam

3. Organization which has registration certificate for the manufacturing product

of the tender, from Gujarat Khadi Gramodyog Board or Khadi and Village

Industries Commission(K.V.I.C)or Commissioner of Cottage Industries.

4. Board/Corporations/PSUs of the Central/State Government for their own

manufactured items.

5. State Government recognized organizations like(i) organizations for blinds,

dumb and deaf, disabled, mentally disabled persons;(ii)women's self-help

group recognized by Gujarat Livelihood Promotion Company; which

participate directly in tendering process for the product which they are

manufacturing / service which /they are providing.

1. Micro & Small Enterprises (MSEs) who participates directly in the tendering

process as Manufacturers or Service Providers, and holds a valid Udyam

Registration, are eligible for exemption from payment of Earnest Money

2. Agencies registered under Udyam in the capacity of Traders, Re-sellers, or

similar categories (i.e. other than Manufacturers/Service Providers) are not

eligible for EMD exemption.

3. Migration period for Reclassification of MSMEs: - ln case of an upward change

in terms of investment in plant and machinery or equipment or turnover or

both, and consequent re-classification, an enterprise shall continue to avail of

EW-286 PUR-F-006 RFQ-

all non-tax benefits of the category (micro or small or medium) it was in before

the re-classification, for a period of three years from the date of such upward

 Vendor Registration with GSECL is not compulsory for submitting this tender.

(4) If any Bank Guarantee submitted against EMD/security deposit/PBG, same should

be valid one year from the date of expiry of BG. Bank Guarantee should be confirmed

through Structured Financial Messaging system (SFMS). SFMS allows

intra/interbank message transfer system of banking. Our bank details are as under.

ACCOUNT NAME GSECL

BANK NAME & BRANCH BOB, SECTOR-21, GANDHINAGAR

IFSC CODE BARB0GANDHI

(5) The tender received after time and date specified in the tender notice will not

be accepted. Once the offer Submitted by the Contractor before due date of

submission, the Contractor will not be allowed to submit revised/

additional/Modified/other after opening of bid. Any alterations/ modification to

the bids received after submission of offer shall not be considered unless carried for

by the Corporation in negotiation.

(6) Any deviation found in Data / Details / Documents between on line offer (e-

tendering) and physically submitted documents (Tender document fee, Technical

offer of the bidder) offer of the same bidder will not be considered and no any further

communication in the matter will be entertained.

Further bidders are requested to submit price – bid (Part-II) on-line only and not to

submit the price bid in physical form. This is mandatory. If price bid is submitted in

physical form, same will not be opened and only on-line submitted price bid will be

considered for evaluation. Further if the quantity quoted differs in the any of the

technical bid forms and in price bid forms, it is discretion of CE Committee –GSECL

to consider the quoted quantity.

(7) PLEASE MENTION:

(a) EPF Code No.: _________________ (The contractor shall have to submit in online

the attested copy of EPF code certificate issued by RPFC without fail otherwise

tender will not be considered )

(c) GSTIN Registration No. : _____________________________________ ( For Works &

(8) In case short submission of documents with bid and / or clarification if any required

from the bidder, The required details / documents may be asked from bidder.

(9) It shall be sole responsibility of the bidder that the uploaded scanned documents (in

PDF form) Remain legible and should not be password protected

(10) Tender will be evaluated on basis of Data / Details / Documents submitted by online

(11) It is mandatory for all the bidders to upload their tender documents by on line only

(E-tendering) in scheduled time. No documents shall be considered physically

which are mentioned for on-line submission only.

(12) The bidders are required to fill up all the online annexure / forms and shall be

uploaded invariably. This is intended for transparency and speedy evaluation of the

bids. Instead of simply confirming / attached in bid / refer physical offer, the Bidder

shall fill in the particulars against appropriate place in respect of each line appearing

in each online annexure. Wherever required, bidder shall invariably have to upload

supporting authentic documents in the online bid. (In the absence of required details

in the online annexure, the purchaser has every right to evaluate the bids

accordingly and bidder cannot raise any objection against any point during

(13) Bidders are requested to remain in touch with the web-site for any amendment /

corrigendum or extension of due date etc

EW-286 PUR-F-006 RFQ-

(14) EMD Fee Demand Draft with different purchaser or agency shall not be accepted.

Tender without EMD shall be rejected.

(15) The GSECL reserves the right to award the work to one or more bidders, considering

their technical and financial capacity OR to reject any or all tenders or accept any

tender without assigning any reason thereof.

(16) Once the offer Submitted by the Contractor before due date of submission, the

Contractor will not be allowed to submit revised/ additional/Modified/other after

opening of bid. Any alterations/ modification to the bids received after submission of

offer shall not be considered unless carried for by the Corporation in negotiation

(17) GSECL reserves the rights to reject any OR all tenders without assigning any

reasons thereof.

(18) Vendor get to register in VMS System through vms.guvnl.com. For registration following

documents are required and mail to [email protected] and

[email protected]. After registration vendor have to upload the invoice in the VMS

system for smooth functioning of payment.

Documents required for Registration:

(2) GST Certificate Copy

(4) Full Name of Vendor

Site : vms.guvnl.com

Username : PAN (PAN number)

Password : MyInvoice@123

Chief Engineer (G)

GSECL: Gandhinagar TPS

Dated seal & signature of

Bidder/Contractor

EW-286 PUR-F-006 RFQ-

GENERAL CONDITONS

The tenderers should thoroughly read all the following clauses before submitting their

 online tender with EMD Fee cover will be opened as per tender notice date and time.

and if the documents towards payment of EMD Fee are found OK then only, offer of

the bidder will be considered for further evaluation.

 EMD will be forfeited (i) if the tender, which it covers, is withdrawn during the validity

of the offer and (ii) the Tenderer fails to furnish / deposit the security deposit.

 “It shall be mandatory to submit 5% security deposit within 10 days from the date of

issue of Letter of Intent before order placement. In case when successful bidder not at

all responding within notice period or withdraws his offer then his EMD shall be

forfeited and he will not be allowed to participate in the tenders invited from the same

office for the period of One year for that place from where tender is invited.”

1. TECHNICAL BID: (Online only not by physically)

1.1) The technical bid comprises scope and nature of works and quantity of works/jobs,

drawings (Refer Schedule-B), required technical qualification for execution of the

works/job etc. for which price are to be quoted. Also, all the technical details of the

stores/materials offered in accordance with the Corporation scope of work,

specification guaranteed technical particulars and conditions, etc

The supplier/contractor should mention separate HSN/SAC code and rate of GST

and cess as applicable for each item of goods/services. If no specifically mentioned

then company will have option to take the prices as exclusive of taxes and duties at

maximum higher slab rates for the evaluation of tenders.

1.2) The Technical Bid shall be opened as per Tender Notice (If possible).Please note that

the required documents should be invariably submitted in online only. If party has

not submitted tender in online is liable to be ignored.

1.3) Contractor has to submit all required documentary evidences thereof to qualify for

acceptance of their technical bid. The acquisition of the tender documents by any

party will not automatically qualify the party as to its capability to execute such or

similar orders. The Corporation shall assess the capability of the party at the time of

evaluation of the technical bids.

1.4) The submission of the offer by any contractor does not mean that the bidder is

qualified for execution of the works. After opening of the online technical bids, the

competent authority will evaluate on the basis of technical qualification criteria. If

contractor’s bid does not meet the technical qualification criteria, then his technical

bid will be ignored. Decision taken by the CE(G),GTPS will be binding to all in this

2.1) The price bid comprises Schedule-B, in which the tenderer has to offer their rates in

accordance with the technical specification specified in technical bid with all

commercial terms and condition. The Price Bid must be submitted strictly as per

Schedule-B and shall be submitted online only, not by physically.

Incomplete bids and amendments and additions to bids after opening of the bids will

be ignored out rightly.

The price bid of those who are techno-commercially qualified shall be opened. After

technical bid is opened, for modification, if any, all shall be given equal chance.

2.2) Price bids of technically acceptable tenders shall be opened after analyzed &scrutiny

of the technical bid.

2.3) The ‘TECHNICAL” and ‘PRICE” Bids shall contain adequate cross-reference wherever

necessary to ensure clear and proper co-relation of the two bids without ambiguities

whatsoever. Any technical questions information and clarifications that may be

required pertaining to this Tender should be referred to the Chief Engineer (Gen),

Gandhinagar, TPS-382041 reserves the right to reject any OR all tenders without

assigning any reasons thereof.

2.4) Bidders have to quote their rates online only as per GSECL’s given format of price

2.5) The offered prices to be indicated in online mode of tender in the format given (i.e.

Schedule-B) the price bid submitted in physical mode shall not be considered.

EW-286 PUR-F-006 RFQ-

CONDITIONS FOR PRICE BID

a) For Works & Supply GST rate will be paid with the applicable GST rules.

b) For Supply Portion Only:-“Party shall have to quote their rates in Schedule “B” of

price bid only along with commercial terms and conditions. The details of applicable

GST, service charges, packing & forwarding charges, freight, insurance, F.O.R. etc.

The supplier/contractor should mention separate HSN/SAC code and rate of GST

and cess as applicable for each item of goods/services. If no specifically mentioned

then company will have option to take the prices as exclusive of taxes and duties at

maximum higher slab rates for the evaluation of tenders.

It is mandatory to indicate GST NO in annexure 10a of tech. bid otherwise if no

specifically mentioned then company will have option to take the prices as exclusive

of taxes and duties at maximum higher slab rates for the evaluation of tenders.

3. Applicability of Goods and Service Tax (GST):-

(a) The tenders shall be evaluated on firm price and cost with GST and cess as

applicable unless otherwise mentioned in the tender documents.

(b) If the supplier/contractor have opted for the composition scheme of GST, the same

must be clearly specified with valid declaration and certificate from department. In

the event of withdrawal/ cessation of the supplier from composition scheme during

the tenure of the contract, the rate(i. e. price) mentioned in the price bid shall be

final and any additional GST will have to be borne by the tenderer himself, In no

case additional amount towards GST or otherwise will be paid/reimbursed to

supplier/contractor.

(c) The bidder shall have to inform their GST no. of the registered place(s) where from

the bidder intends to supply the goods/services, meaning there by the bidder has to

supply the goods/services from the relevant declared/ registered place(s) of supply

(d) The bidder shall not include GST in their quoted rates; but the bidder has to

separately indicate the GST rate, amount in the price bid schedule.

(e) In-case Govt notification comes for change in GST , the same will be applicable.

(f) Bidder should indicate GST no.( copy of GST registration to be enclosed) and PAN

NO. (copy of PAN to be enclosed) Tenders submitted without GSTIN No by the

firms, the offer will be rejected without entering into further correspondence.

Chief Engineer (G)

GSECL: Gandhinagar TPS

Dated seal & signature of

Bidder/Contractor

EW-286 PUR-F-006 RFQ-

Other Terms & Conditions

1. Contractor shall indemnify GSECL against for any injury and/or damage that may

be caused in his man or material. Moreover, the contractor shall be fully responsible

for any damage caused to the Corporation’s properties done by his man/materials

while executing the work. The Corporation will be entitled to recover the damage

from the party’s bill.

2. At any time if GSECL feels that progress of work is unsatisfactory and work force of

contractor is inadequate, other agencies/ departmental personnel will be put in

parallel for expediting the work. Amount so incurred will be recovered from the

contractor’s bill. In this case decision of the Engineer-in-charge shall be final and

binding to the contractor.

3. At any stage of the contract period, if the contractor fails to complete the job or his

work is not found satisfactory the same will be got done at his cost and risk and

additional expenditure incurred by the Corporation will be recovered from him by

giving one week's notice.

4. To sublet or transfer of contract without prior written approval of Corporation shall

be treated as breach of contract and it shall be punishable by forfeiting the S.D. as

well as termination of contract.

5. The Corporation reserves the right to forfeit the S.D. in case of any breach of

contract and in case of disputes. The decision of Chief Engineer (Gen), TPS

GANDHINAGAR shall be final, binding & acceptable to the Contractor. If contractor

fails to start the Work as Stipulated, the E.M.D. & S.D. Shall be forfeited.

6. Conditional tender will not be accepted. Withdrawal of tender condition

unilaterally by you before or after opening of tender will not be permitted.

7. The contractor has to carry out the required work strictly according to guidance

given by the Corporation's responsible officer.

8. The Corporation reserves the right whether the materials to be accepted, or not. Only

specified and scheduled materials are to be examined by Corporation's officer and

then if suitable will be accepted by the Corporation.

9. The contractor shall submit his bill in triplicate to the CE(G), GSECL, TPS,

Gandhinagar which will be paid after the certificate regarding correct receipt of the

materials in good condition.

10. The rates should be quoted without any condition. The rates be written in words and

figures legibly.

11. Revision of prices or any commercial terms affecting the price after opening of

technical bids shall not be considered and will be ignored.

12. The contractor shall have to execute an agreement with the Corporation on a non

judicial stamp paper, the cost of which will have to be borne by the contractor and

will have to sign the contract and tender booklet of the Corporation.

13. SECURITY DEPOSIT: In tender process for L1 bidder(lowest bidder) security

deposit will be charged as per table below:

Category of the Unit Security Deposit

Works up to Rs. 5 Works More than Rs.

Enterprise or Exempted 3% of Order Value

Organization which are

exempted from paying

For all other Enterprises 5% of Order Value 5% of Order Value

Note: Security Deposit will be collected from the successful tenderer at the rates

mentioned above. This may be recovered by deduction through running bills of the

contractors and / or by treating the Earnest Money Deposit (Bid Security) paid at the time

of submission of the tender.

14. The Bank Guarantees will be executed on the standard form prescribed by the

corporation. In case of the Bank Guarantees furnished / submitted, they should

have clear one time validity till the completion of the order in all respects and up to

the expiry of Guarantee period from the date of the work completion. Bank

EW-286 PUR-F-006 RFQ-

Guarantee for Interim period will not be allowed. If by any reasons the work period is

extended then contractor should undertake to renew the Bank Guarantee at least

one month before the expiry of the validity failing which GSECL will be at liberty to

encash the same.

“It shall be mandatory to submit security deposit as per above table within

days from the date of issue of Letter of Intent before order placement. In case

when successful bidder not at all responding within notice period or withdraws

his offer then his EMD shall be forfeited and he will not be allowed to

participate in the tenders invited from the same office for the period of One

year for that place from where tender is invited.”

If the Tenderer fails to pay the Security Deposit or defaults in execution

of the orders placed or if GSECL suffers any financial loss due to this, then

GSECL will be at liberty to adjust the amount from other orders of the same

firm or by encashing the Bank Guarantee.

All the costs of the stamp papers, other than required for payment is to be

made through SIDBI / ICICI by Board, are to be borne by you as per the Govt. of

India’s latest guidelines.

15. VALIDITES OF THE OFFERS:

The offers will have to be kept valid for a period of 180 days from the date of opening

of technical bids. In case of finalization of the tender is likely to be delayed, the

tenderers will be asked to extend the same without change in the prices or any

terms and conditions of the offer. If any change is made, original or during the

extended validity period, the offers will be liable for outright rejection without

entering into further correspondence in this regard and no reference will also be

16. If successful contractor fails to pay the required security deposit and does not come

forward to execute the work, the full value of EMD will be forfeited by the

17. Any terms and conditions mutually agreed to writing shall be for a part of the

18. Payment will be made as per GSECL’s rule.

19. The authorized officer/person of the Corporation will have the liberty to check the

material and work etc.

20. Regarding the quality and acceptance of the jobs the authorized officer's decision will

be binding and final and no dispute on this account will be entertained.

21. General terms and conditions of the Corporation for works contract will be made

applicable for this work also.

22. No material for the said work will be supplied by the GSECL except specified in

schedule thereof.

23. WORK COMPLETION PERIOD: The Tenderers will have to confirm work

completion period as specified in this tender. Delay in execution of order on

account of any other reason will be subject to penalty.

24. PBG (Not Applicable) : “The supplier/contractor/party (i.e. tenderee) has to give

Bank Guarantee with validity period of additional 01 (one) month i.e. more than

actual Guarantee/Warranty period of 6/12/18/24/36/48/60 months (depending

upon product) to safeguard Company’s interest in case of any eventuality happening

on the last day of the Guarantee/Warrantee period after office hours of the Bank or

Bank holidays.”

25. PENALTY FOR LATE EXECUTION OF WORK: Any delay that may take place in

supply and / or erection, testing and commissioning activities beyond contractual

cutoff date / stipulated period in the order shall be subjected to penalty (not

liquidated damages) at the rate of ½% of the contract price / order price per week or

part thereof subject to a maximum of 10% of the total contract value / order value

(i.e. End cost including taxes & GST).

26. Statutory variations:-any statutory increase or decrease on the taxes and duties

subsequent to your offer if it takes place within the original contractual delivery date

will be to the company’s account subject to the claim being supported by

documentary evidence. However if any decrease takes place after the contractual

delivery date the advantage will have to be passed on the company

EW-286 PUR-F-006 RFQ-

27. If the work is not done as per specification given by the GSECL in stipulated time in

all respects, the penalty will be levied as per GSECL's rules.

28. The GSECL shall have the right to make any changes, additions / deletions or

modifications in any terms / conditions of the tender and / or specifications as may

be deemed necessary by the GSECL at its sole discretion at any time before the due

date of opening of the tender.

29. Tenderer should furnish a list of orders for similar work executed by them indicating

the name of the party and their order reference to whom they have worked, to be

furnished in Annexure- 6. Failure to do this will result on contractor’s tender being

rejected without any reference.

30. GSECL does not accept the printed conditions of any Tenderer. It will be ignored

without any reference; hence tenderers should withdraw such printed conditions if

31. Tenders will be accepted only on or before due date and time of opening.

32. If technical deviations furnished by the Tenderer are not agreeable to the GSECL, the

offers may be ignored. However it will be solely at GSECL’s discretion to consider the

technical deviations OR not for considering the Tenderer. No correspondences of the

Tenderer after opening of the bid will be entertained in this matter.

33. The contractor will be responsible and liable for any damage to man and materials

during his work.

34. While execution of this job our plant and auxiliaries will be in running conditions.

Hence contractor has to take all precautions for safety etc. Safety belts etc. also to be

used wherever necessary while working.

35. GSECL reserve the right to terminate the contract if quantity shown in Schedule-B is

executed earlier.

36. All the terms and conditions specified in Industrial & safety laws are binding on the

37. Registration certificate under labor contract act will have to be obtained before

execution of contract.

38. The laborers shall be supplied for 8 hours a day, so contractors shall arrange

39. The following List of Annexures and Documents (available in this tender document)

should be invariably submitted along with the tender:

(i) Schedule–“A” Indicating the Description of work & quantities for the tender.

(ii) Schedule–“B” Price Bid to be submitted online ONLY”

(iii) Annexure-“A” - Technical Scope of Work

(iv) Form of Bankers undertaking Performa for E.M.D and S.D.

(v) Annexures – 1 TO

(vi) Certificate – “A”.

(vii) Document of Important Instructions.

All the above documents should be duly filled in, signed & stamped with company’s

seal should be submitted along with the Technical Bid in online only.

40. Please note that any additional conditions / deviations, if any, found in the

Commercial terms & conditions, then the Price Bids of such tenderers will not be

opened and no further correspondences in the matter will be allowed.

41. Tenderer should invariably fill up all the details of all the Annexure of this tender

document. This is mandatory. Also all the Annexures should be duly signed by

authorized signatories with their rubber stamp and along with Company’s Rubber

(Round) seal / stamp affixed on each paper.

42. All the tenderers must ensure that all the relevant documents / papers submitted

with the tender should be serially numbered, and properly documented. This must

43. All the above points should be complied by the Tenderers. If not, tenders are likely to

be ignored without making any further reference.

44. If participating bidder/agency have stake in one or more other agencies / bidder who

are participating in same tender and on account of submission of wrong information

/ declaration in the tender / enquiry certificate – A, then the bidder will be declared

as disqualified automatically and EMD / SD will be forfeited. Further, GSECL shall

take stern action including stop dealing with their firms’

EW-286 PUR-F-006 RFQ-

45. The CE(G),GSECL, Gandhinagar, reserves right to reject/accept any or all tenders

without assigning any reasons thereof and to split up the work between the parties

as the case may be.

46. Relationship of employee: - Every bidder should, at the time of submission of bid,

give a declaration as under.

“If in any bidder company/firm, the interest (i.e. Shareholding in company and share

in partnership firm) of any employee of the tendering Company or his/her relative as

defined in section 2(77) of the Company’s act. 2013 is 10% or more, the tendering

Company will not deal with such company/firm at all.

Tenderer therefore, must specifically disclose this fact in his technical bid. Non-

disclosure of such facts would immediately disqualify the tenderer for further dealing

with the tendering company.”

47. Conflict of interest among Bidders/Agents: A bidder shall not have conflict of

interest with other bidders. Such conflict of interest can lead to anti-competitive

practices to the detriment of Procuring Entity’s interests. The bidder found to have a

conflict of interest shall be disqualified. A bidder may be considered to have a conflict

of interest with one more parties in this bidding process, if:

a) they have proprietor/partner(s)/Director(s) in common; or

b) they receive or have received any direct or indirect subsidy/financial stake from

any of them; or

c) they have the same legal representative/agent for purposes of this bid; or

d) they have relationship with each other, directly or through common third parties,

that puts them in a position to have access to information about or influence on

the of bid of another bidder; or

e) Bidder participates in more than one bid in this bidding process. Participation by

a bidder in more than one Bid will result in the disqualification of all bids in

which the parties are involved. However, this does not limit the inclusion of the

components/sub-assembly/assemblies from one bidding manufacturer in more

f) in cases of agents quoting in offshore procurements, on behalf of their principal

manufacturers, one agent cannot represent two manufacturers or quote on their

behalf in a particular tender enquiry. One manufacturer can also authorize only

one agent/dealer. There can be only one bid from the following:

1. The principal manufacturer directly or through one Indian agent on his

2. Indian/foreign agent on behalf of only one principal.

g) a Bidder or any of its affiliates participated as a consultant in the preparation of

the design or technical specifications of the contract that is the subject of the

h) in case of a holding company having more than one independently

manufacturing units, or more than one unit having common business

ownership/management, only one unit should quote. Similar restrictions would

apply to closely related sister companies. Bidders must proactively declare such

sister/common business/ management units in same/similar line of business.

i) Bidder shall not act in contravention/violation to the provisions of competition

act, as amended from time to time. Every bidder should, at the time of

submission of bid, give a declaration, that bidder shall not have conflict of

interest with other bidders, as above

48. "All bidders shall submit the details/documents in support of Technical Qualification

Requirements duly certified and verified for authenticity from Specified Third-Party

inspection Agency (TPIA) or Statutory Auditor of their Company or Practicing CA/CA

Firm along with a certificate regarding verification of authenticity of documents as per

the format placed at Annexur-1. All the documents submitted by the bidder in support

of the meeting Technical QR only shall be digitally signed by the Specified Third-Party

inspection Agency (TPIA) or Statutory Auditor of their Company or Practicing CA/CA

EW-286 PUR-F-006 RFQ-

The verification and certification of authenticity of documents is acceptable from any of the

1. M/s Competent inspectorate and Consultants Pvt. Ltd, Hyderabad, lndia.

2. M/s Gulf Lloyds industrial Service lndia Pvt. Ltd.-Ahmedabad.

3. M/s international Certifications Services.

4. M/s lntertek lndia Pvt. Ltd.

5. M/s SGS lndia Pvt. Ltd.

6. M/s Moody lnternational (lndia) Pvt. Ltd.

7. M/s TUV SUD South Asia (P) Ltd.

8. M/s TUV Rheinland (lndia) Pvt. Ltd.

9. M/s Bureau Veritas (lndia) Pvt. Ltd.

10. Hertz lnspection & Services Pvt. Ltd.

11. IRCLASS Syslems and Solutions Pvt. Ltd.

Verification for authenticity shall not be applicable in following cases.

1: Bidders having proven track record or regular suppliers/contractors (i.e.

2: Past order copies of GSECL as these documents can be verified internally.

Bidders shall be responsible for getting their documents/ credentials verified & certified

by the Specified Third-Party inspection Agency (TPIA) or Statutory Auditor of their

Company or Practicing CA/CA Firm in support of Technical QR. All the costs pertaining to

third party verification and certification (including those by statutory auditors) shall be

borne by the Bidder. GSECL shall have no liability (financial or otherwise) towards the

same and shall not be liable for any claim/ dispute between the bidder and the Specified

Third-Party inspection Agency (TPIA) or Statutory Auditor of their Company or Practicing

Chief Engineer (G)

GSECL: Gandhinagar TPS

I/ We hereby agree for the terms & conditions laid down in Tender.

Contractor's Signature

With Seal & Date

EW-286 PUR-F-006 RFQ-

Undertaking from Third Party Inspection Agency/Statutory Auditor or Practicing

(On letter head digitally signed by a person duly authorized to Sign on behalf of the firm)

Gandhinagar TPS.

Subject: Authentication of veracity of documents submitted by M/s …….. in support of

Meeting the Qualifying Requirements

Ref : Tender no.: ________________

M/s._______________________________________________(hereinafter called Bidder) having

Registered office at_____________________intend to participate in above referred tender of

The tender condition stipulates that the bidder shall submit supporting Documents

pertaining to Qualifying Requirement duly verified and certified by Third-Party Inspection

Agency (TPIA) or Statutory Auditor of their Company or Practicing CA/CA Firm as per the

list mentioned in the bidding documents.

In this regard, it is hereby confirmed that we have examined the following documents,

which are also attached with this letter. The same has been verified from the Original

Documents and / or Client for authenticity.

We hereby confirm that the following documents are found to be genuine and authentic.

1. Doc ref. no. _________________________ dated______________ (name of Documents)

2. Doc ref. no. _________________________ dated ______________ (name of Documents)

All the aforesaid documents have been digitally signed by us as a certificate of

We further confirm that we neither have any vested interest in aforesaid tender nor have

any conflict of interest in respect of above tender.

This certificate is issued at the request of M/s._____________________________ (Bidder) for

the purpose of participating in the subject tender/s.

EW-286 PUR-F-006 RFQ-

General Terms & Conditions

1. Contractor shall indemnify GSECL against for any injury and/or damage that may

be caused in his man or material. Moreover, the contractor shall be fully

responsible for any damage caused to the Corporation’s properties done by his

man/materials while executing the work. The Corporation will be entitled to

recover the damage from the party’s bill.

2. At any time if GSECL feels that progress of work is unsatisfactory and work force

of contractor is inadequate, other agencies/ departmental personnel will be put in

parallel for expediting the work. Amount so incurred will be recovered from the

contractor’s bill. In this case decision of the Engineer-in-charge shall be final and

binding to the contractor. At any stage of the contract period, if the contractor

fails to complete the job or his work is not found satisfactory the same will be got

done at his cost and risk and additional expenditure incurred by the Corporation

will be recovered from him by giving one week's notice.

3. Subletting the contract to other agency is not permitted unless and otherwise

approved by the competent authority.

4. The contractor has to carry out the required work strictly according to guidance

given by the Corporation's responsible officer.

5. The Corporation reserves the right whether the materials to be accepted, or not.

Only specified and scheduled materials are to be examined by Corporation's officer

and then if suitable will be accepted by the Corporation.

6. The contractor shall submit his bill in triplicate to the CE(G), GSECL, TPS,

Gandhinagar which will be paid after the certificate regarding correct receipt of the

materials in good condition.

7. Any terms and conditions mutually agreed to writing shall be for a part of the

8. The authorized officer/person of the Corporation will have the liberty to check the

material and work etc.

9. Regarding the quality and acceptance of the jobs the authorized officer's decision

will be binding and final and no dispute on this account will be entertained.

10. General terms and conditions of the Corporation for works contract will be made

applicable for this work also. The booklet is attached herewith.

11. No material for the said work will be supplied by the Corporation except specified

in schedule thereof.

12. Penalty :-If the work is not done as per specification given by the Corporation in

stipulated time in all respects, the penalty will be levied as per Corporation's

rules. Any delay that may take place in supply and / or erection, testing and

commissioning activities beyond contractual cutoff date / stipulated period in the

order shall be subjected to penalty (not liquidated damages) at the rate ½ % of the

contract price / order price per week or part thereof subjected to a maximum of

10% of the total contract value/ order value (i.e. End cost including GST)

13. Statutory variations:-any statutory increase or decrease on the taxes and duties

subsequent to your offer if it takes place within the original contractual delivery

date will be to the company’s account subject to the claim being supported by

documentary evidence. However if any decrease takes place after the contractual

delivery date the advantage will have to be passed on the company.

14. The contractor will be responsible and liable for any damage to man and materials

during his work.

15. While execution of this job our plant and auxiliaries will be in running conditions.

Hence contractor has to take all precautions for safety etc. Safety belts etc. also to

be used wherever necessary while working.

16. Corporation reserve the right to terminate the contract if quantity shown in

Schedule-B is executed earlier.

17. All the terms and conditions specified in Industrial & safety laws are binding on

18. Registration certificate under labor contract act will have to be obtained before

execution of contract

EW-286 PUR-F-006 RFQ-

19. The laborers shall be supplied for 8 hours a day, so contractors shall arrange

20. Payment Terms: Party has to accept payment terms as per GSECL rules only i.e.

as per actual work done. NO ADVANCE payment will be allowed. Net Payment will

be released within 30 days after completion of work and submitting their relevant

21. Dispute Resolution Mechanism: For works contracts and composite Contracts, the

arbitration mechanism shall be governed by the Gujarat Public Works Contracts

Disputes Arbitration Tribunal Act, 1992 as per below details.

(1) Amicable Settlement : "Any dispute, difference, controversy or claim between

the parties arising out of or relating to this contract with reference to the

construction, interpretation, breach, termination or validity thereof (herein

after referred as "the Dispute") shall, upon the written request of either party

by referred to the authorized representatives of the Disputing Parties for

resolution. The authorized representatives shall promptly meet and attempt to

negotiate in good faith a resolution of the Dispute within thirty days of the

service of the request."

(2) Arbitration: If the Parties fail to amicably resolve the disputes or differences or

contrary claims as indicated herewith in sub clause (1) of Clause 21 arising

under or in connection with the present works contracts, whether pertaining

to works contracts alone or works and procurement both, the same shall be

referred to arbitration under the Gujarat Public Works Contracts Disputes

Arbitration Tribunal Act, 1992."

22. For procedure for health check-up accordingly bill shall be reimbursed once

during total contract period (for as & when and AOH/COH contract) maximum up

to Rs.1000 or actual cost per worker/ labour /person, whichever is minimum

after verification & recommendation by concern doctor. In case any worker left the

work in between than for replacement Worker Company will not provide any

reimbursement, however it is compulsory to submit new report of replacement

worker for fitness certificate at contractor’s own expense.

23. For Periodic Medical examination, No reimbursement for periodic medical

examination to be given to contract employee for whom GSECL are conducting

Periodic Medical examination at company’s cost at GTPS. If a contractor fails to

undergo periodic medical examination, they have to undergo prescribed

investigation as per hazard analysis from outside, No reimbursement to be given

for these investigations.

Chief Engineer (G)

GSECL: Gandhinagar TPS

I/ We hereby agree for the terms & conditions laid down in Tender.

Contractor's Signature

With Seal & Date

EW-286 PUR-F-006 RFQ-

BID - QUALIFICATION CRITERIA FOR TECHNICAL BID

Work of item rate contract for Maintenance works – routine / schedule / preventive /

Sub: breakdown / overhauling of K.G. Khosla / Kirloskar make Air compressor with

associated auxiliaries of Unit No. 3, 4 & 5 of Gandhinagar TPS…as & when required

Pre-Qualification Criteria (PQC) (To be submitted with Technical Bid):-

The bidders are requested to submit the technical bid with the following credentials

for technically qualifying criteria in soft ONLY.

A. Technical qualification criteria:

1. The bidder should produce certificate/document as evidence of having an experience for

similar work* carried out satisfactorily in government / semi government / state electricity

board / corporation body / private limited company / public limited company during last 7 years

ending last day of month previous to the one in which applications are invited should be either

of the following:

a. Three similar completed works costing not less than the amount equal to Rs.

b. Two similar completed works costing not less than the amount equal to Rs.

c. One similar completed work costing not less than the amount equal to Rs.1573292.80

Similar work means – Party shall have an experience for Servicing / Overhauling / Maintenance

work of Balanced opposed Piston reciprocating type Air Compressor / AC Plant compressor / Gas

system compressor in Units of GSECL, NTPC and Power generating stations of other electricity

board /corporation and Private Company. Experience in other company/firm as an employee will not

B. Financial qualification criteria:

1) The Average Annual Turnover of the bidder, shall not be less than Rs 05.89 Lacs (Rupees Five

lakh Eighty Nine Thousand only) during the preceding three (3) financial years as one date of

Techno-Commercial bid opening.

2) Net worth of bidder shall not be less than 100% of the bidder’s paid up share capital as on the last

day of the preceding financial year. In case the Bidder meets the requirement of Net worth based on

the strength of its Subsidiary (ies) and/or Holding company and/or Subsidiaries of its Holding

Companies wherever applicable, the Net worth of the Bidder and its Subsidiary (ies) and/or Holding

company and/or Subsidiary (ies) of the Holding Company, in combined manner should not be less

than 100% of their total paid up share capital. However individually, their Net worth should not be less

than 75% of their respective paid share capitals.

Net worth in combined manner shall be calculated as follows:

Net worth (combined )= (x1+x2+X3)/(y1+y2+y3) X 100, where x1,x2, x3 are individual net worth which

shall not be less than 75 % of the respective paid up share capitals and y1, y2, y3 are individual paid

up share capitals.

3) In case the bidder is not able to furnish its audited financial statements on stand- alone entity

basis, the unaudited unconsolidated financial statements of the bidder can be considered acceptable

provided the bidder further furnishes the following documents for substantiation of its qualification.

 Copies of the unaudited unconsolidated financial statements of the bidder along with copies of

the Audited consolidated financial statements of its Holding Company.

EW-286 PUR-F-006 RFQ-

 A Certificate from the CEO/CFO of the Holding Company, stating that the unaudited

unconsolidated financial statements form part of the Consolidated Annual Report of the

4) In cases where audited results for the last preceding financial year as on the date of techno-

commercial bid opening are not available, the financial results certified by a practicing Chartered

Accountant shall be considered acceptable. In case, Bidder is not able to submit the Certificate from

practicing Chartered Accountant certifying its financial parameters, the audited results of three

consecutive financial years preceding the last financial year shall be considered for evaluating the

financial parameters. Further, a Certificate would be required from the CEO/CFO, stating that the

Financial results of the Company are under audit as on the date of Techno commercial bid opening

and the Certificate from the practicing Chartered Accountant certifying the financial parameters is not

5) The bidder must submit Average Annual Turnover and Net worth Certificate in support of Financial

QR, duly certified and verified for authenticity from Independent Statutory Auditor of their company /

Practicing Charted Accountant/ C.A. Firms / TPIA (Third-Party Inspection Agency ) empanelled /

approved by GSECL along with copy of Annual Audited Accounts of last three years.

Note for point No.1, 2, 3&4:

i. Other income shall not be considered for arriving at annual turnover.

ii. “Holding Company" and “Subsidiary Company” shall have the meaning ascribed to them as per

Companies Act of India, in vogue.

iii. Net worth means the sum total of the paid up share capital and free reserves. Free reserve means

all reserves credited out of the profits and share premium account but does not include reserves

credited out of the revaluation of the assets, write back of depreciation provision and amalgamation.

Further, any debit balance of Profit and Loss account and miscellaneous expenses to the extent not

adjusted or written off, if any, shall be reduced from reserves and surplus.

B. Other requirements:

1. Details of P.F. code No. from the appropriate provident fund authorities and Certificate of

separate provident fund account number.

2. Details of Tools, tackles and equipment available with firm relevant to the job/subject tender.

3. Details of skilled/semi-skilled persons presently employed by the contractor having sufficient

knowledge of similar jobs.

4. Bidder shall have to confirm to submit update workman Group insurance policy covering all

the labour who are going to work at GTPS site on award of the Contract.

5. Bidder shall have to confirm to submit update valid labour license from the Asstt. Labour

Commissioner on award of the Contract, if applicable

6. Bidder shall have to submit the copy of PAN card for Income Tax with documentary proof.

7. Bidder shall have to submit the copy of updated valid GST registration number.

8. Bidder has to fill undertaking Performa regard to stop deal / black list thereof.

1. The Chief Engineer (Gen.), GSECL, GTPS reserve right to reject any tender or all tenders

without assigning any reason thereof and to split up the work between more than one party as

the case may be.

2. Non-compliance of above criteria the technical bid is liable to be rejected. After

acceptance of the Technical Bid, the Price Bid will be considered for opening.

Chief Engineer (G)

GSECL: Gandhinagar TPS

Dated seal & signature of

Bidder/Contractor

EW-286 PUR-F-006 RFQ-

Sr. Details Confirmation

No. (Tick √ any one)

1 Annexure – 2 YES / NO

2 Firm’s details as per “Annexure –3” YES / NO

3 Copy of the un-priced schedule (Description and YES / NO

price). “Annexure - 4”.

4 Work Completion Period as per “Annexure- 5” YES / NO

5 Past experience details as per “Annexure-6” YES / NO

6 Performance certificates as per “Annexure-7” YES / NO

7 ANNEXURE – 8 YES / NO

8 ANNEXURE – 9 YES / NO

9 ANNEXURE – 10 YES / NO

10 ANNEXURE – 11 YES / NO

11 ANNEXURE – 12 YES / NO

12 Certificate of Important Instruction & certificate-A YES / NO

13 INTEGRITY PACT YES / NO

14 Schedule-“A” & Annexure-“A” (GSECL’s work/ Scope YES / NO

of work to be carried out by contractor specified duly

signed and with seal of firm.)

I / WE, confirm that following documents are attached with the technical bid of the

Signature of the Tenderer

Seal of the Firm

NOTE: ALL THE DOCUMENTS SHOULD BE PROPERLY FILED AND SHOULD BE

GIVEN FLAG MARKING FOR IDENTIFICATION.

EW-286 PUR-F-006 RFQ-

Subject: Work of Item rate contract for Maintenance works - routine / schedule /preventive

/ breakdown / overhauling of ' K. G. Khosla / Kirloskar' make Air compressors with

associated auxiliaries of Unit no. 3, 4 & 5 of Gandhinagar TPS… as & when required.

Reference: Tender No. EW-286

Due on date: / / 2026 .

In connection with the above subject and reference I/ We confirm the following:

1. I / We, the under signed have read and examined the Scope of Work & requirements

during execution of work in tender mentioned under reference along with the

Commercial terms and conditions.

2. I / We, declare that our Technical Bid is strictly in line with the Tender

specifications/work.

3. Further, I / We also agree that additional conditions / deviations, if any, found in the

Commercial terms & conditions, our offer shall be out rightly rejected without

assigning any reason thereof.

4. We hereby agree for the terms & conditions laid down in Tender.

All the bidders are requested to see and verify the documents of

a) General safety rules / norms” to be observed by the contractors

b) Additional terms and conditions regarding industrial law and other related

matters for the tender documents.

c) General rules and directions for the guidance of contractor booklet of GSECL,

GTPS on our website under heading of “Rules for Works”

And confirm that all the above documents you have verified & certify as below

“I/we hereby has read the above documents and agree for the Safety Rules, Industrial

Laws and Contract Booklet (a, b & c as above) and accordingly submitted my/our

Signature of the Authorized

Representatives of the firm

Seal of the Firm

Name of the Tendering Firm / Agency:

EW-286 PUR-F-006 RFQ-

DETAILS OF THE FIRM

Tenderer may MANDATORILY fill all the details in this form.

(These details are necessary to create the database of Contractors)

Contractor Name

Within Gujarat / Outside Gujarat /GST

Pvt. Firm / Public Ltd. / State Govt. Under (Indicate the relevant status)

taking / Central Govt. undertaking

Vendor Registration Letter No. & Date

(If registered and Letter issued by Board) -

(If Applicable)

Vendor Registration Fee (If Applicable) Paid / Not Paid (Tick any one, for New

Vendor Registration Date (If Applicable) -

Vendor Registration Validity Period From Date___________ to Date___________

(If Applicable)

P.F NO (Also Physical Document is

required along with the Technical Bid)

PAN NUMBER (Also Physical Document is

required along with the Technical Bid)

Custom No. and Date (If applicable)

Electrical License Type(If Applicable) (Also

Physical Document is required along with

the Technical Bid)

License Validity Period (If Applicable) From Date___________ to Date___________

Account Number of Bidder

Type of Account of Bidder

Branch Name & Address

Contact Number of the Branch

Copy of Cancelled Cheque

COMPANY EMAIL ID FOR

CONFIRMATION OF PAYMENT

Address of Registered Office Factory Works Authorized

Contact person name

City & Pin code

Phone Nos.(Office)

Phone Nos.(Residence)

Web site address

EW-286 PUR-F-006 RFQ-

UN – PRICED SCHEDULE (COPY WITHOUT PRICES)

Description Quantity Unit

EW-286 PUR-F-006 RFQ-

Work Completion Period

EW-286 PUR-F-006 RFQ-

DETAILS OF THE EXPERIENCE FOR SIMILAR TYPE OF WORK AS PER TENDER’S

PRE-QUALIFICATION CRITERIA.

Party should submit below executed detailed work order physically along with the

Technical Bid. This is mandatory.

Sr. NAME ORDER DESCRIPTION ORDER ORDER STATUS, IF REMARKS

No OF REFERENCE OF WORK AMOUNT FULLY ORDER

WORK No. & DATE EXECUTED. UNDER

YES/NO EXECUTION

A GUJARAT STATE ELECTRICITY CORPORATION LTD /SISTER COMPANY.

B OTHER STATE ELECTRICITY BOARD

C OTHER ORGANISATION.

EW-286 PUR-F-006 RFQ-

LIST OF PERFORMANCE CERTIFICATES SUBMITTED WITH THE TECHNICAL BID.

Party should submit below executed work performance certificate physically along

with the Technical Bid.

Sr. No. Name of the Authority by Reference No. & Details of Works

whom certificate is issued date

EW-286 PUR-F-006 RFQ-

ANNEXURE – 8 ( for Works )

Bidder must fill up below details & should place at the top of the Technical Bid.

1 PRICES: [FIRM ONLY]

(Please Specify YES / NO.)

2 TAX: [IN PERCENTAGE] ( GST )

3 The Last three-year Audited Annual Accounts, Positive

Net worth certificate, and Average Annual Turnover

certificate certified by charted accountant as Per

Qualification Requirement

4 Please quote your GST Registration No. (Also Physical

Document is required along with the Technical Bid)

5 Please quote your PF Registration No. & Date. (Also

Physical Document is required along with the Technical

6 PENALTY TERMS AGREED :

(Please Specify YES / NO.)

7 SECURITY TERMS AGREED:

(Please Specify YES / NO.)

8 DETAILS OF EMD PAYMENT (as applicable as below)

a) DD No & Date & Name of Bank

b) B.G. No. & Date & name of Bank

c) Cash details

9 Completion of Works

(Please Specify YES / NO.)

10 VALIDITY OF THE OFFER AGREED:

(Please Specify YES / NO.)

11 PAYMENT TERMS AGREED:

(Please Specify YES / NO.)

12 WORK OFFERED AS PER SCHEDULE-B: (YES/NO)

13 TELEPHONE NOS. & FAX NO:

14 Authorized person of the firm :

15 Name of the proprietor, partners, directors [as the case

may be], along with address, telephone, fax no. etc.

16 If Vendor Registration is Done:(If Applicable)

(Please submit copy of Vendor Registration approval -

letter in the EMD cover).

EW-286 PUR-F-006 RFQ-

TECHNICAL DEVIATIONS IF ANY TO BE FURNISHED IN THIS ANNEXURE ONLY AND

TO BE SUBMITTED WITH TECHNICAL BID.

EW-286 PUR-F-006 RFQ-

(UNDERTAKING IN REGARD TO QUOTED PRICE)

(Bidder should not quote their prices in this page)

Sub: Undertaking in regard to quoted prices.

All bidders will have to furnish the following undertaking duly filled in, signed and

“This is to certify that we have not worked for the subjected tender viz.…………………. to

other SEBs / Power Utilities with this tender details of GSECL at lower % price than the %

prices quoted in this tender by us for the same item during last Six (6) Months.”

The prices quoted by us for the same item to other SEBs during the last six (6) months

are given below:

Signature of the Tenderer

Seal of the Firm

EW-286 PUR-F-006 RFQ-

ANNEXURE-10A (For Supply)

Vendor must fill up below details & should place at the top of the Technical Bid.

1. PRICES:[FIRMONLY]

(Please Specify YES/NO.)

2. Rates offered FOR:__________________

3. GST :[INPERCENTAGE]

(Please Specify IN/EXCLUSIVE/EXEMPTED)

Please quote your GST Registration No. &Date

Please specify GST NO

4. In case of GST(SGST,CGST OR IGST)please specify place

of Manufacturer unit from where material is to be supplied

5. PENALT YTERMS AGREED:

(Please Specify YES/NO.)

6. SECURITYTERMSAGREED:

(Please Specify YES/NO.)

7. P.G TERMS AGREED (Wherever applicable):

(P.G.-Performance Guarantee)(Please Specify YES/NO.)

8. DETAILS OF EMD PAYMENT

(Please Specify DD/BG/Pay order/ Valid SSI/Valid NSIC

No./Valid UDYAM/Valid KVIC/Valid MSME with CSPO

9. DELIVERY TERMS AGREED:

(Please Specify YES/NO.)

10. VALIDITY OF THE OFFER AGREED:180 Days from the

date of opening of Technical Bid

11. PAYMENT TERMS AGREED: 80% against T.R.C. within

30days & balance 20% within 45 days

12. ITEMS OFFERED:

13. TELEPHONE NOS. & FAX NO:

14. Authorized person of the firm:

15. Name of the proprietor ,partners, directors [As the case

may be], along with address, telephone, fax no. e-Mail ID

Signature of Tenderer Company’s roundseal

EW-286 PUR-F-006 RFQ-

(UNDERTAKING IN REGARD TO STOP DEAL / BANNED FOR BUSINESS DEALING /

BLACK LIST THEREOF).

Sub: Undertaking in regard to Stop Deal / Banned for Business dealing / Black List

Ref: Tender No.:

M/S. ______________________________________ here by certify that M/S

__________________________________________ and their proprietor / any partner / any

directors of the firm is not stop deal and/or banned for business dealing and/or black

listed by GUVNL and/or their any subsidiary company viz.

GSECL/GETCO/DGVCL/MGVCL/UGVCL/PGVCL.

(Confirmed / not confirmed)

Contractor’s Signature

With Seal & Date

EW-286 PUR-F-006 RFQ-

Bidders must furnish the scan copy of below details along with technical Bid.

(1) A copy of order on hand.

(2) Detail order copies submitted as per Annexure-6.

(3) Performance Certificate if any.

(4) Documentary Proof for Partnership of proprietor, Partners, Directors (as the case

may be), along with Address, Telephone No, Fax No. etc. if any.

(5) The Last three-year Audited Annual Accounts, Positive Net worth certificate, and

Average Annual Turnover certificate certified by charted accountant as Per

Qualification Requirement.

(6) A copy of Goods and Service Tax Registration document along with valid Registration

Number as per Annexure –

(7) A copy of PF Registration document along with valid Registration Number as per

(8) A valid B.G. against EMD or DD for the payment of EMD as per Annexure-8.

IMPORTANT INSTRUCTIONS

1. The Tenderer should clearly give certificate along with the Technical Bid:

“This is to confirm and certify that the offer submitted by me is strictly in accordance

with the GSECL’s Work Tender specifications and as per Technical detail work/

drawing as mentioned in the Tender Specifications. There is no commercial or

Technical deviation in the offer from the Corporation’s Tender Specification. I

undertake to abide by the GSECL’s tender description and Particulars. I undertake to

complete work strictly as per the GSECL’s Technical specification/ Scope of work/

Guaranteed Technical Particulars / Drawing, even if any technical deviations are

mentioned by me. I also undertake to abide by all commercial conditions of the GSECL,

including work completion schedule.”

(Signature of the Tenderer)

1. Any offer without above certificate will not be considered and the tender will be out

rightly ignored in the absence of above certificate.

2. After opening of the Tender, if it is found that the offer given by the Tenderer is not

according to the GSECL’s specifications, Guaranteed Technical Specifications/

Scope of work, Drawing and commercial terms and conditions and false certificate

is given by the Tenderer, then GSECL will not deal with the firm for the present

Tender. It is, therefore requested that the Tenderer should take care in giving their

offer and submission of documents.

3. The conditional tenders will not be accepted.

EW-286 PUR-F-006 RFQ-

[On Company's Letter Head]

(Required for price justification, if necessary)

(UNDERTAKING IN REGARD TO QUOTED PRICE)

(All bidders will have to furnish the following undertaking duly filled in, for all the

quoted items/works of the tender along with online Technical Bid)

Ref.: Tender No: / Bid. No.:

We, the undersigned, hereby declare and undertake that we have not accepted or

executed any Letter of Acceptance (LOA) or Purchase Order (PO) at a unit ex-works

price/any work at rate lower than the rate offered in this tender in any station of

GSECL/GUVNL & Subsidiaries/CPSU/SPSU/IPP etc. during the period from six (6)

months prior to two (2) months after the bid submission date of this tender.

We also understand that LOA / Purchase Order placed by any station of

GSECL/GUVNL Subsidiaries/CPSU/SPSU/IPP etc. on the basis of above

undertaking shall not be considered as ‘offered’ price for the tender items in

subsequent tender, if it is not within period mentioned above

I/ We accept above undertaking.

Seal of the firm Signature of the tenderer

With designation

EW-286 PUR-F-006 RFQ-

Gujarat State Electricity Corporation Ltd.

Thermal Power Station, GANDHINAGAR

(On Firm’s Letter Head)

ON FIRM’S LETTER HEAD:-

of M/s. __________________________________ hereby certified that M/s.

______________________________________is not related with other firms who have submitted

tenders for the same work under this inquiry / tender and the interest (i.e.

Shareholding in company and share in partnership firm) of any employee of the tendering

Company or my/our relative as defined in section 2(77) of the Company’s act. 2013 is

10% or more, the tendering Company will not deal with such company/firm at all.

Also I /We declare that, I/We have not conflict of interest with other bidders, as

Conflict of interest among Bidders/Agents

A bidder shall not have conflict of interest with other bidders. Such conflict of

interest can lead to anti-competitive practices to the detriment of Procuring

Entity’s interests. The bidder found to have a conflict of interest shall be

disqualified. A bidder may be considered to have a conflict of interest with one

more parties in this bidding process, if :

a) they have proprietor/partner(s)/Director(s) in common; or

b) they receive or have received any direct or indirect subsidy/financial stake

from any of them; or

c) they have the same legal representative/agent for purposes of this bid; or

d) they have relationship with each other, directly or through common third

parties, that puts them in a position to have access to information about or

influence on the of bid of another bidder; or

e) Bidder participates in more than one bid in this bidding process.

Participation by a bidder in more than one Bid will result in the

disqualification of all bids in which the parties are involved. However, this

does not limit the inclusion of the components/sub-assembly/assemblies

from one bidding manufacturer in more than one bid.

f) in cases of agents quoting in offshore procurements, on behalf of their

principal manufacturers, one agent cannot represent two manufacturers or

quote on their behalf in a particular tender enquiry. One manufacturer can

also authorize only one agent/dealer. There can be only one bid from the

1. The principal manufacturer directly or through one Indian agent on his

2. Indian/foreign agent on behalf of only one principal.

g) a Bidder or any of its affiliates participated as a consultant in the

preparation of the design or technical specifications of the contract that is

the subject of the Bid;

EW-286 PUR-F-006 RFQ-

h) in case of a holding company having more than one independently

manufacturing units, or more than one unit having common business

ownership/management, only one unit should quote. Similar restrictions

would apply to closely related sister companies. Bidders must proactively

declare such sister/common business/management units in same/similar

line of business.

i) Bidder shall not act in contravention/violation to the provisions of

competition act, as amended from time to time.

SIGNATURE OF THE TENDERER

WITH DESIGNATION.

SEAL OF THE FIRM:

EW-286 PUR-F-006 RFQ-

GUJARAT STATE ELECTRICITY CORPORATION LIMITED, BARODA Date:

To, create an environment where Business Confidence is built through Best Business

Practices and in fostered in an atmosphere of trust and respect between providers of goods

and services and their users for the ultimate benefit of society and the nation.

GSECL’S COMMITMENT PARTY’S COMMITMENT

■ To maintain the highest ethical ■ Not to bring pressure

standards in business and recommendations from outside GSECL

professions. to influence its decision.

■ Ensure maximum transparency ■ Not to use intimidation, threat

to the satisfaction of inducement or pressure of any kind on

stakeholders. GSECL or any of it’s employees under

any circumstances.

■ To ensure to fulfill the terms of ■ To be prompt and reasonable in

agreement / contract and to fulfilling the contract, agreement, legal

consider objectively the viewpoint obligations.

■ To ensure regular and timely ■ To provide goods and/or services

release of payments on due dates timely as per agreed quality and

for work done. specifications at minimum cost to

■ To ensure that no improper ■ To abide by the general discipline to be

demand is made by employees or maintained in our dealings.

by anyone on our behalf.

■ To give maximum possible ■ To be true and honest in furnishing

assistance to all the Vendors / information.

Suppliers/ Service Provider and

other to enable them to complete

the contract in time.

■ To provide all information to ■ Not to divulge any information,

suppliers/contractors relating to business details available during the

contract/job which facilitate him course of business relationship to

to complete the contract/job others without the written consent of

successfully in time. GSECL.

■ To ensure minimum hurdles to ■ Not to enter into carter/syndicate/

vendors/suppliers/contractors in understanding whether formal/non-

completion of agreement/ formal so as to influence the price.

contract/ work order.

Seal & Signature Seal & Signature

(GSECL’s Authorized Signatory) (Party’s Authorized Person)

EW-286 PUR-F-006 RFQ-

GUJARAT STATE ELECTRICITY CORPORATION LIMITED.

TPS: GANDHINAGAR.

Work of Item rate contract for Maintenance works - routine / schedule

/preventive / breakdown / overhauling of ' K. G. Khosla / Kirloskar'

make Air compressors with associated auxiliaries of Unit no. 3, 4 &

of Gandhinagar TPS… as & when required.

GENERAL SPECIFCATIONS FOR AIR COMPRESSORS

Make : K. G. Khosla

Total Installed Qty :15 Nos

Capacity (FAD) :15.27 M3/min

Suction Pr.:1.5 to1.9 Kg/cm2

Working pr.:8.1 Kg / cm2

 SCOPE OF WORK

The scope of work consists and includes routine, schedule, preventive, breakdown and

overhauling of Balanced Opposed Piston (B.O.P) type “K. G. Khosla / Kirloskar” make Air

compressors [Model: 2HA2QT], maintenance of control air drier unit, Air dryer blowers, valves,

solenoid operated 4-way/ 2-way valves, replacement of silica gel, hydro test of air receiver

tanks, etc. for efficient operation as well as optimum output of each air compressors of 200 /210

MW Unit no. 3, 4 &

For trouble free proper assessment of mechanical maintenance of air compressor works,

following brief description and guide line provided for reference of bidder.

[1] DAILY CHECKINGS:

1.1 Check the operating parameters viz. Lube oil pressure, First stage pressure and

Temperature, Second stage pressure and temperature at all measuring points, Cooling

water pressure / flow etc.

1.2 Check the oil level in the crank case.

1.3 Check suction pressure and delivery pressure.

1.4 Check HP / LP valves air leaks from its body, any abnormal noise sound.

1.5 Check the slide way on the cross head, gland and oil seal for abnormal heat generation and

1.6 Check noise and vibration.

1.7 Check the valve cover and unloader piping for air leakage and the oil piping for oil

1.8 Check the glands for air & oil leakages.

1.9 Check the V belts.

1.10 Check any air, oil, water leakage from any parts of air compressor.

1.11 Check the tightness of bolts / nuts / flanged joints etc.

1.12 Check whether the drain traps on the intercooler & the after cooler for their satisfactory

[2] ROUTINE MAINTENANCE WORKS:

2.1 Oil toping and maintain oil level in the crankcase.

2.2 Collection of dirty / waste oil.

2.3 Oil leakage attending from oil line / flange joint /oil filter / oil line replacement( Inside /

outside of compressor body) etc.

EW-286 PUR-F-006 RFQ-

2.4 Oil leakage attending from crankcase top cover / flywheel side cover / LP-HP cylinder

cross head guide.

2.5 Cleaning of lube oil cooler / tube leakage checking & plugging / replacement.

2.6 Replacement of oil filter element / complete filter assembly.

2.7 Belt removing, refitting & alignment / tightening.

2.8 Correction / adjustment of flapped / twisted /slipped "V" belt/s.

2.9 Replacement of damaged / broken "V" belt/s & alignment / tightening.

2.10 Replacement of new "V" belts.

2.11 Cooling water leakage attending.

2.12 Air leakage attending from compressor accessories viz. Inter / after cooler body,

air delivery lines, air drying unit, volume bottle, HP/ LP cylinder body etc by

2.13 Air leakage attending from compressor parts viz. Suction / discharge valve

Packing, Loading-Unloading line joints, drain valves, air delivery pipe joints etc.

2.14 Replacement of Air / Water / Oil lines.

2.15 Repairing / Replacement of moisture drain vales

2.16 Replacement of air suction filter element / body

2.17 Replacement /refitting LP/HP cylinder oil scrapper / wiper ring, gland packing,

three / six piece in gland box.

2.18 Replacement / refitting of LP / HP piston assembly after fitting of guide ring &

Piston ring and setting of clearances in the LP / HP cylinder.

2.19 Replacement of tube bunch of Inter cooler

2.20 Replacement of tube bunch of after cooler

2.21 Replacement /Overhauling of water valve, Discharge isolating valve & NRV.

[3] SCHEDULED MAINTENANCE WORKS:

3.1. Cleaning of air compressor and surrounding area. .... 15 Days

3.2. Cleaning of suction air filters.... [Every 15 days & As when req.]

3.3. Cleaning of lube oil strainer & oil filter element.... 15 Days

3.4. Backwash of cooling water system of LP / HP Cylinder, Inter / After cooler etc..... [As and

3.5. Cleaning of LP cylinder water jackets.... [As and when req.]

3.6. Cleaning of HP cylinder water jackets.... [As and when req.]

3.7. Servicing of LP / HP cylinder suction / discharge valve … [45 days / As and when reqd. ]

3.9. Replacement of oil from crankcase oil chamber.... 4 months / As and when reqd.

3.9. Replacement of Silica gel of Air drying unit.... Yearly

3.10. Serving moisture drain traps … As and when reqd.

[4] PREVENTIVE MAINTENANCE WORKS:

Sr. SUB PART NAME MAINTENANCE ACTION DURATION

No ASSEMBLY ACTIVITY RECOMMENDED

4.1 Bolts & Nuts Cylinder nuts Check Check the loosening Weekly

& foundation and retighten

4.2 Crosshead Check Check the loosening Weekly

bolt, cap nut, and retighten

4.3 Air Suction Valve Servicing Dismantle, clean, 45 days /

and Delivery assembly, check for As and

valve of LP / Valve spring, wear/damage, when

HP Cylinder Valve plates, replace damage reqd.

Valve packing part, leak test & refit

4.4 Un-loader Suction Unloader Servicing Dismantle, clean, 45 days

check the operation

EW-286 PUR-F-006 RFQ-

4.5 LP / HP Piston body, Check Check the 45 days

Piston piston ring, clearance, wear,

guide ring damage, ovality

4.6 Inter cooler Tube nest Cleaning Clean the scales 4 months

assembly, /As &

Intercooler when Req.

4.7 After cooler Tube nest Cleaning Clean the scales 4 months

assembly, /As &

Intercooler when Req.

4.8 Connecting Crosshead Check Check wear, 6 months /

Rod & Main small end clearance & As & when

Bearing bearing, adjustment Req.

4.9 Main Gear pump Check Check wear of gears 6 Months /

lubrication driving and oil and bearings As & when

system pump Req.

In a schedule maintenance planning, for each compressor contractor has to follow up the

maintenance schedule and as well as service manual of manufacture guideline. All the actions

must be carried out intimation and knowledge of Engineer In-charge.

[5] Hydro test of each receiver tanks of air compressors is to be carried out when required.

Necessary provisions for the hydro test are carried out by the contractor in advance as per

instruction of Engineer-In-charge.

[6] FOR AIR DRYING UNITS:

1) Overhauling and greasing of air drier sets two way and four way valve.

2) Maintenance of Air blower.

3) Replacement of silica gel / activated alumina.

4) Attending any air leakages of system.

5) Cleaning of all equipment.

[7] COMPLETE OVERHAULING OF AIR COMPRESSORS:

The complete overhauling of compressor by dismantling all the components of compressor,

record the clearances, checking of wear & tear. Identify and replace worn out parts

rectification of abnormality, if any observed. Replacement of worn out / damaged spares by

new one or reclaim one, whichever is available with GSECL, matching of parts, to maintain

clearances as per O&M manual. Refitting of entire compressor, while reassembly the

clearances and important data are to be logged and record should be maintained. All these

activities are to be carried out in presence of GSECL representative. During overhauling

contractor shall have to carry out following work also.

Cleaning of inter cooler & after cooler, replacement / repairing of HP / LP valves, HP / LP

piston / piston rod / rings, HP / LP cylinders, HP / LP end covers, overhauling of oil pump,

replacement / tightening, alignments etc. After carrying out all above work as per instruction

of Engineer In-charge as well as O&M manual procedure, the contractor has to offer 72 Hrs

trouble free trial run of overhauled compressor. If any defects / performance deficiency

observed during the same shall be attended immediately by contractor at free of cost. If

GSECL is arranging any performance test of overhauled compressor, contractor shall have to

coordinate and make necessary arrangement for performance test.

EW-286 PUR-F-006 RFQ-

[8] BREAKDOWN MAINTENANCE WORK:

The breakdown maintenance work of air compressors consists of assessment of route cause

of occurrence, assessment of damaged parts, Replacement of worn out /damaged spares by

new one or reclaim one, whichever is available with GSECL, matching of parts, to maintain

clearances as per O&M manual. Refitting of entire compressor, while reassembly the

clearances and important data are to be logged and record should be maintained. All these

activities are to be carried out in presence of GSECL representative.

The above scope of works is for brief information of contractor. Actually all maintenance

works are to be carried out as per OEM’s O&M manual recommendations. In any case any

item/s is/are not narrated in above scope of works but recommended by OEM’s O&M manual,

contractor shall have to carry out those works.

The O&M manual recommendation shall be binding and dominant regarding this maintenance

contract as this contract works is covers any kind of mechanical maintenance work of air

compressor & air system inside air compressor house.

 TECHNICAL TERMS AND CONDITIONS :

01. DESCRIPTION:- This part of work contract consists and includes of all the maintenance

works of Air Compressor, its accessories, valves, Air dryer unit, its valves and accessories to

carry out the safe, smooth, economical & efficiently maintenance of the same. All above

works are to be carried out as per the scope of work, O&M manual service guide lines, O&M

manual Inspection standards and as directed by Engineer-In-charge.

The Air compressors are remains in service round the clock. This para of contract also

includes and consists of attending leakages and keeping air compressors & equipment neat

and clean, checking its running parameters according to direction of O&M manual.

In short, the contractor is bound to do all the maintenance works related to air compressors

and associated auxiliaries as per O&M manual and as directed by Engineer-In-charge.

02. The scope of work shall also include transportation, handling & re-crediting of old / new

materials, equipments, spares etc. from GSECL Main store / Departmental store to site area

and site to Main store / Departmental store vice versa as directed by Engineer-In-charge.

The dismantled items / equipments/ spares shall have to be shifted or stacked properly

immediately from working area to Main store or other department / areas of Turbine unit no.

3, 4 & 5 as part of this contract without any extra cost and as directed by Engineer- In-

After required repair / maintenance works, the old spares should be removed immediately

from the site and working area should be kept cleaned and cleared.

03. The scope of work shall also include repairing / servicing of old removed parts /assembly etc.

The contractor shall also keep certain parts assembly in ready position for immediate

replacement i.e. suction / discharge valve assembly, LP/HP piston assembly, bearings etc.

The old removed suction / discharge valve assemblies are dismantled, servicing, cleaned

and reassemble for reuse as directed by Engineer-In-charge.

04. In addition of General Description, T&C, mentioned elsewhere, in this tender

documents bellow listed special terms & conditions are pertains to maintenance work

of Air Compressor.

04.01 The contractor shall have to keep his / their maintenance staff in general shift duty. In

emergency work, he is bounded to work round the clock till the work completion. No

additional payment shall be made for extra time or man power.

04.02 The contractor shall be equipped / mobilized / ready in all respects with required /

sufficient skilled manpower and all necessary general tools tackles to take-up any type of

maintenance job on air compressors and its auxiliaries either online, preventive and /or

breakdown of any compressor at a short notice of one hour.

EW-286 PUR-F-006 RFQ-

04.03 Contractor should be resourceful with sufficient skilled staff and labours every day from

existing staff in such a way that breakdown work can be carried out within short time,

otherwise Rs. 500/- per day of generation loss will be recovered from the bill.

04.04 The contractor will have to engage more manpower (maintenance staff) as and when

required as per condition or as per instruction of GSECL representative for urgent work.

04.05 In case of breakdown maintenance the contractor shall have to mobilize all his resources

within one hour of notice and take-up the required jobs as directed by Engineer-In-charge

on emergency basis and shall have to complete within least possible time.

04.06 The contractor’s maintenance supervisor or staff will have to report for duty every day

morning before starting the job to the representative of GSECL. Non-reporting of

contractor’s maintenance staff will be viewed seriously as considering negligence of work.

04.07 The contractor’s staff (supervisor or technicians) must be available during general shift and

when work is going on.

04.08 The contractor’s supervisor / technician has to entirely check all the air compressors and

its accessories every day while starting general shift & record the observations.

04.09 The contractor’s maintenance staff will have to check all the parameter of Air compressors

& air dryers, oil temp & pressure, water temp & pressure, air pressure at various stage,

loading / unloading of system etc, which have to remain within its working limit prescribed

by the manufacturing O&M manual.

04.10 All the standby compressors should be ready to put service; maintenance of running

compressor should be arranged in such a manner that difference between max. Running

and minimum running hours of different compressors should not be more than 120 hours.

04.11 Any drop in air pressure due to leakage / heavy leakage inside compressor house must be

attended immediately to avoid any emergency in plant and overburdening of compressor.

04.12 During the maintenance work, contractor staff should be more vigilant and careful while

handling heavy spares besides running air compressors.

04.13 The contractor shall be kept and maintained air compressors and surrounding area neat &

clean free of debris, scrap, dust, lubricant, oil all the times so that work is not held up at

any time and exercise following checks regularly in co-ordination with operating staff, oil

level, oil pressure, water temperature of inter cooler, after cooler, Ist and IInd stage of air

temperatures, air & oil leakage attending work.

04.14 The contractor will have to maintain a log book in which required parameters, details of

spares used, oil consumption etc. to be noted for each compressor separately. Scrap

material and used worn-out unserviceable spares must be returned as per procedure of

04.15 The contractor’s maintenance staff should report any defect observed or given by

operation section or any complain-faults-wear & tear etc. to the site Engineer Incharge &

will have to arrange the rectification.

04.16 The line clear / PTW shall be issued to the contractor or their authorized technical

supervisor for maintenance work and work shall be treated as completed when the

equipment is accepted by operational staff and put into service. Any defects / work

request noticed on putting air compressors into operation after repair shall have to be

rectified as part of this contract immediately.

04.17 In case of any work on motor side and if removal of motor coupling is required from EMD

side, the contractor has to carry out de-coupling of belts / alignment and recoupling of

belts etc. of the compressor immediately after getting clearance from EMD side.

04.18 The maintenance of Air Compressors should be fully efficient, i.e. oil consumption, power

consumption, consumption of spares should be optimum.

04.19 In case of damage caused to accessories or air compressor itself due to poor

maintenance and carelessness or negligence etc of contractor’s maintenance staff, same

should be rectified / repaired / replaced by contractor at his own cost & report of such

occurrence should be made immediately to GSECL authority.

04.20 During the maintenance work, any damage to valuable parts of GSECL or damage to the

parts due to mis-handling and excessive wastage of material will be considered seriously

and Rs. 1000/- per item will be deducted from the bill. The amount will be decided by

Engineer-In-charge and binding to the contractor.

04.21 Contractor has to carry out repairing / welding of the minor damaged / broken worn out

spares, however, if spares / components are felt beyond repair by Engineer – in charge

EW-286 PUR-F-006 RFQ-

then same shall be supplied by GSECL at free of cost to contractor for replacement.

However decision of Engineer-in-charge shall be final and binding upon the contractor.

04.22 At any instant / incident, the contractor’s staff is / are not available for the works,

GSECL has every right to carry out these works, either departmentally or by deploying

other agency at all risks and cost of contractor.

04.23 Contractor shall collect all dirty lube oil / unserviceable lube oil in empty drum and shall

credit the same to Main store / Sub store / other department.

04.24 The unit-wise history register of inspection & replacement of air compressor spares,

consumption of lube oil shall be kept & maintained by the contractor & submitted to

Engineer-in-charge every week or as and when demanded by Engineer-in-charge.

05.01 Following facilities will be given by GSECL free of cost.

1. Required spare parts of air compressors, gaskets, nut bolts, grease, special slings, welding

rods, O2 / DA, copper / MS / GI piping etc. as per requirement.

2. Compressed air, water as per requirement in each unit.

3. Electrical connection at one mutually agreed point in each unit will be given free of cost

and consumption will be given free of cost from the said points.

4. Crane / forklift facility for heavy parts shifting from main store to site shall be provided if

5. Workshop facility only related to this work contract if available.

05.02 Following items are to be arranged by contractor at his own risk and cost.

1. Arrangement for required tools and tackles, cleaning brush etc. required to attend the job.

2. Transportation of spare parts from main store to site, crediting of old parts / replaced spare

parts to be credited to main store, etc except heavy components viz. HP / LP Cylinder,

Crankcase, Flywheel, Cross head, Cross head guide, motor Pulley, LP / HP piston

assembly, Inter / After cooler tube bunch etc.

3. Transportation of manpower during odd Hrs. or during night to be arranged by the

Contractor in case of emergency.

4. PPE’s like goggles, helmets, safety boots and ear plugs etc. for their staffs to avoid any

05.03 Following facilities will be given by GSECL on chargeable basis if available.

1) Medical facility if available with GSECL.

2) Accommodation i.e. Quarter/Room/Hostel will be provided by GSECL on chargeable

basis, if available.

06. Time Limit: The Overall Time Limit for the Work Contract is 24 Months from the date of

commencement of work order. The GSECL reserves Right to extend the validity for a

period of 12 Weeks and contractor is abided to carry out the work at the same rates and

terms and conditions of the order.

07. PENALTY CLAUSE: If the work is not done as per specification given by the Corporation in

stipulated time in all respects, the penalty will be levied as per Corporation's rules.

1. Any delay that may take place in supply and / or erection, testing and commissioning

activities beyond contractual cutoff date / stipulated period in the order shall be subjected

to penalty (not liquidated damages) at the rate of 0.5% of the contract price / order price

per week or part of thereof subject to maximum of 10% of the total contract value / order

value (i.e. End Cost including taxes and duties).

2. To keep the each air compressors in good condition, some preventive / scheduled checks

are prescribed in scope of work. Non-implementation of such checks of running each air

compressors will result in deduction of Rs.300/- per air compressor per each check as

3. Occurrence of poor workmanship, frequent repeated maintenance will be viewed

Seriously. The amount of Rs. 500/- per occurrence shall be deducted from the bill with

the approval of competent authority.

EW-286 PUR-F-006 RFQ-

08. CLEANLINESS:

The contractor is responsible to keep the work area cleaned day to day. No separate

payment shall be made for keeping the work area clean.

09. PERFORMANCE GAURANTEE: Party shall have to give performance guarantee for the

overhauled air compressor (i.e. any abnormal noise, 1st stage 2nd stage pressure, oil

pressure, load-unload as per OEM standard parameter) for minimum three- months from the

date of compressor put in service, and if, any problem / passing is observed, the same shall

be rectified by the party and accordingly, the guarantee period shall be considered from the

re-putting of the repaired valve in service.

In case of any dispute, the decision of the Chief Engineer, GSECL, GTPS shall be final and

binding to the contractor. The GSECL reserves the right to split each item in to more than

one agency and place the order accordingly. All parties should therefore, carefully evaluate

and fill up the rate, keeping themselves ready to execute order for any one item or more,

allotted to them by the GSECL.

10. STATUTORY VARIATION:

Any statutory increase or decrease in the taxes and duties subsequent to your offer if it takes

place within the original contractual delivery date will be paid / recovered subject to the claim

being supported by documentary evidence. However, if any decrease takes place after the

contractual delivery date, the advantage will have to passed on to the GSECL.

11. Consider JOB equal to Number for per Compressor of Schedule-B Item Sr. No. 2, 3, 5, 6,

12. GSECL will provide unfurnished bachelor quarter/ hostel to party, if available, after meeting

the requirement of GSECL’s staff. Party shall have to pay the rent of the quarter/ hostel as

per GSECL’s rule.

GENERAL TERMS & CONDITION:

1. The Contractor may be visit the Site and familiarized themselves thoroughly with the Site

Conditions, Equipments and Systems before submitting the Tender, if desire. For Site Visit,

the Tenderers may contact Engineer in Charge of Site Office with permission of undersigned

on any Working Day during Working Hours before submitting the Tender.

2. The Materials, Design and Workmanship shall satisfy the relevant Indian Standard. The Job

Specification contained herein and Code referred to where the join Specification Stipulate

Requirements in addition to these contained in the Standard Code and Specifications, these

Additional Requirements shall be satisfied.

3. Contractor shall comply with the Factory Acts, Labour Laws and Safety Laws in force and

amended from time to time.

4. Any other Rules and Regulations, Conditions etc. that are in force at present and that may be

framed by the GSECL from time to time in connection with the Contracts will be binding and

acceptable to the Contractor.

5. Party has to furnish the Documents for Insurance of Workmen, Labours License (If

Apllicable) and other Account Section Formalities before starting the Works, failing to which

Contractor shall not be allowed to commence the Work.

6. The Contractor should authorize the Qualified Authentic Representative to GSECL who in

turn will collect the Material, Works Permit and remains available at Site to receive

instructions from GSECL Engineer in Charge to execute the Works. All Formalities as per

GSECL’s Procedure are to be obeyed by Representatives of Contractor.

7. The Contractor should intimate the Names and Addresses of his authorized and responsible

Representative so that they can be contacted when required in connection with execution of

the said Works. The Contractor should also be present to report the Work daily to Engineer

in Charge and receive necessary instruction. If the Contractor does not remain present then

his Contract will be terminated as Execution can’t be allowed in absence of the Contractor.

8. The Party shall have to do all related works as per Site requirement and as per instruction of

Engineer in Charge. Party has to arrange of his own adequate all types of Tools and Tackles

required for the Works including Skilled Supervisors, Technicians, Welders, Riggers, Helpers

for the Continuous Works round the clock to meet Scheduled Overhauling / Works within

EW-286 PUR-F-006 RFQ-

Time Limit. Works should be carried out in proper way and in co-ordination with Each / Other

Works / Agency so that Work should not suffer.

9. Contractor shall make his Own Full Proof Arrangement of Storage of Spares / Consumables,

Tools Tackles, etc. required for subject Work and shall be responsible for Safe Custody of

such items at his Site / Store. In case of Theft / Lost / Damage of such Items, Contractor will

liable for loss or damage and same will be recovered from the contract bill, if loss occurs to

10. Contractor shall indemnify GSECL against for any Injury and / or Damages that may be

caused in his Man or Material. Moreover, the Contractor shall be Fully Responsible for any

Damages caused to the GSECL’s Properties / Men done by his Man / Materials while

executing the Work. The GSECL will be entitled to recover the Damages from the Party at an

11. At any time if GSECL feels that Progress of Works is unsatisfactory and Work Force of

Contractor is inadequate, other Agencies / Departmental Personnel will be put in parallel for

expediting the Works. Amount so incurred will be recovered from the Contractor’s Bill. In this

case the Decision of the Engineer in Charge shall be final and binding to the Contractor.

12. Whenever Contractor brings Material from Outside the P/H Premises, he must get an Entry

Pass Separate for Tools / Tackles / Machinery and Consumable Items and he should

produce One Copy of Such Entry Pass to Concern Department for their Verifications /

13. Party shall submit Material Account along with Bills in Triplicate.

14. Payment will be made for Actual Work Done only.

15. GSECL shall provide the Open Space at Appropriate Place in Plant Area suitable for keeping

Materials, Tools, Equipments, etc. and for making Temporary Office. On Expiry / Completion

/ Termination of Contract, Contractor shall have to vacate the Premises immediately after

Work completed satisfactorily otherwise the Rent will be recovered as per GSECL’s Rules if

not vacated in time.

16. GSECL will try to give Residential Accommodation on Chargeable Basis as per Rules to the

possible extent depending upon the Availability. But this will not be the Right of Contractor.

The Quarter is to be vacated immediately as soon as the Work is completed satisfactorily.

17. Subletting the Contract to other Agency is not permitted unless and otherwise approved by

the Competent Authority.

18. For any Ambiguity and Conflict, the Decision of the Chief Engineer (Gen.), GSECL, GTPS

shall be final and binding to the Contractor.

19. The GSECL reserves the right to terminate the Contract at any Time without giving Notice of

Termination or any Reason and entertaining of Claims / Compensations.

CHIEF ENGINEER (GEN.),

GSECL: TPS: GANDHINAGAR.

Dated seal & signature of

Bidder/Contractor

EW-286 PUR-F-006 RFQ-

ON STAMP PAPER OF Rs.300/-]

EMD BANK GUARANTEE FORMAT

FOR TENDER NO.__________

GUJARAT STATE ELECTRICITY CORPORATION LIMITED

WHEREAS M/s. __________________________________________(Name and Address of the

Firm/company) having their registered Office at

________________________________(Address of the Firm’s registered Office) (hereinafter

called the “Tenderer”) wish to participate in the Tender No._______________ for

_________work (Supply / Erection / Supply & Erection Work, etc.) of ______________________

(Name of the Material/equipment / work) for Gujarat State Electricity Corporation Limited

(hereinafter called the “Beneficiary”) and WHEREAS a Bank Guarantee for

Rs._____________ (Amount of Bank Guarantee towards EMD) valid till ____________ (mention

here date of validity of this Guarantee which will be Six months from the date of submission

of bid of the tender) which is required to be submitted by the Tenderer along with the

We,_____________________________________________(Name of the Bank & address of the

Branch giving the Bank Guarantee) having our registered Office at

_____________________ (Address of Bank’s registered Office) hereby give this Bank

Guarantee No. _________________ dated ____________ and hereby agree unequivocally

and unconditionally to pay immediately on demand in writing from Beneficiary

Gujarat State Electricity Corporation Limited or any Officer authorized by it in this

behalf any amount up to and not exceeding Rs.____________(Amount of E.M.D.),

Gujarat State Electricity Corporation Limited on behalf of the Tenderer.

We, ____________________________________________ (Name of the Bank) also agree that

withdrawal of the Tender/Bid/EOI or part thereof by the Tenderer within its validity or

Non submission of Performance Guarantee towards execution/supply period by the

Tenderer within 15 days from the date of issue of Letter of Acceptance by the Gujarat State

Electricity Corporation Limited would constitute a default on the part of the Tenderer

and that this Bank Guarantee is liable to be invoked & encashed within its validity by the

Beneficiary in case of any occurrence of a default on the part of the Tenderer and that the

encashed amount is liable to be forfeited by the Beneficiary.

This agreement shall be valid and binding on this Bank up to and inclusive of

_______________ (mention here the date of validity of Bank Guarantee) and shall not be

terminable by notice or by Guarantor for change in the constitution of the Bank or the

Firm of Tenderer or by any reason whatsoever and our liability hereunder shall not be

impaired or discharged by any extension of time or variations or alterations made, given,

conceded with or without our knowledge or consent by or between the Tenderer and

the Gujarat State Electricity Corporation Limited.

Notwithstanding anything contrary contained in any law for the time being in force or

banking practice, this Guarantee shall not be assignable, transferable by the Beneficiary

(i.e. GSECL) Notice or invocation by any person such as assignee, transferee or agent of

beneficiary shall not be entertained by the Bank. Any invocation of the Guarantee can be

made only by the beneficiary directly.”

NOTWITHSTANDING anything contained hereinbefore our liability under this

Guarantee is restricted to Rs.__________(Amount of EMD) (Rupees

__________________________________) (in words). Our Guarantee shall remain in force till

_____________ (Date of validity of the Guarantee). Unless demands or claims under this

Bank Guarantee are made to us in writing on or before ___________ (Date of validity of the

Bank Guarantee), all rights of Beneficiary under this Bank Guarantee shall be forfeited

and we shall be released and discharged from all liabilities there under.

EW-286 PUR-F-006 RFQ-

Please Mention here Complete Postal Signature of the Bank’s

Address of the Bank with Branch Code, Authorised Signatory with

Telephone and Fax Nos Official Round seal

NAME OF DESIGNATED BANKS : As per Annexure – I

EW-286 PUR-F-006 RFQ-

(ON STAMP PAPER OF Rs.300/-)

FORM OF BANKER’S UNDERTAKING

(For Performance Guarantees (PBG) towards execution/supply period ( Security

Deposit ) as per Commercial Terms & Conditions of Tender)

We, __________________________________________________(name of the Bank and Address of

the Branch giving the Bank Guarantee) having our registered Office at

registered office) hereby give this Bank Guarantee No.

unequivocally and unconditionally to pay immediately on demand in writing from

the Gujarat State Electricity Corporation Limited, or any Officer authorized by it

in this behalf any amount up to and not exceeding Rs. _____________ (Amount of

Performance Guarantee towards execution/supply period ) Rupees

said Gujarat State Electricity Corporation Limited on behalf of

M/s.___________________________________________________ who have entered into a contract

for the supply / works specified below :

This agreement shall be valid and binding on this Bank up to and inclusive

of___________________(Date of validity of the Bank Guarantee) and shall not be

terminable by notice or by change in the constitution of the Bank or the firm of

Contractors / Suppliers or by any other reason whatsoever and our liability

hereunder shall not be impaired or discharged by any extension of time or

variations or alterations made, given conceded or agreed, with or without our

knowledge or consent, by or between parties to the said within written contract.

“Notwithstanding anything contrary contained in any law for the time being in force or

banking practice, this Guarantee shall not be assignable, transferable by the beneficiary

(i.e. GSECL). Notice or invocation by any person such as assignee, transferee or agent of

beneficiary shall not be entertained by the Bank. Any invocation of the Guarantee can be

made only by the beneficiary directly.”

“NOT WITHSTANDING” anything contained herein before, our liability under this

guarantee is restricted to Rs._______________(Rupees

___________________________________________only). Our guarantee shall remain in force

until _______________ (date of validity of the Bank Guarantee).Unless demands or

claims under this Bank Guarantee are made to us in writing on or before _____________

(Date of validity of the Bank Guarantee), all rights of Beneficiary under this Bank

Guarantee shall be forfeited and we shall be released and discharged from all liabilities

Please mention here complete Signature of the Bank’s authorized

Postal Address of the Bank with signatory with Official Round Seal.

Branch Code, Telephone and Fax

NAME OF DESIGNATED BANKS : As per Annexure - I

EW-286 PUR-F-006 RFQ-

(ON STAMP PAPER OF Rs.300/-)

FORM OF BANKER’S UNDERTAKING

(For Performance Guarantees (PBG) towards Guarantee/Warranty period as per

Commercial Terms & Conditions of Tender)

We, __________________________________________________(name of the Bank and Address of

the Branch giving the Bank Guarantee) having our registered Office at

registered office) hereby give this Bank Guarantee No.

unequivocally and unconditionally to pay immediately on demand in writing from

the Gujarat State Electricity Corporation Limited, or any Officer authorized by it

in this behalf any amount up to and not exceeding Rs. _____________ (Amount of

Performance Guarantee towards Guarantee/Warranty period ) Rupees

Gujarat State Electricity Corporation Limited on behalf of

M/s.___________________________________________________ who have entered into a contract

for the supply / works specified below :

This agreement shall be valid and binding on this Bank up to and inclusive

of___________________(Date of validity of the Bank Guarantee) and shall not be

terminable by notice or by change in the constitution of the Bank or the firm of

Contractors / Suppliers or by any other reason whatsoever and our liability

hereunder shall not be impaired or discharged by any extension of time or

variations or alterations made, given conceded or agreed, with or without our

knowledge or consent, by or between parties to the said within written contract.

“Notwithstanding anything contrary contained in any law for the time being in force or

banking practice, this Guarantee shall not be assignable, transferable by the beneficiary

(i.e. GSECL). Notice or invocation by any person such as assignee, transferee or agent of

beneficiary shall not be entertained by the Bank. Any invocation of the Guarantee can be

made only by the beneficiary directly.”

“NOT WITHSTANDING” anything contained herein before, our liability under this

guarantee is restricted to Rs._______________(Rupees

___________________________________________only). Our guarantee shall remain in force

until _______________ (date of validity of the Bank Guarantee).Unless demands or

claims under this Bank Guarantee are made to us in writing on or before _____________

(Date of validity of the Bank Guarantee), all rights of Beneficiary under this Bank

Guarantee shall be forfeited and we shall be released and discharged from all liabilities

Please mention here complete Signature of the Bank’s authorized

Postal Address of the Bank with signatory with Official Round Seal.

Branch Code, Telephone and Fax

NAME OF DESIGNATED BANKS : As per Annexure – I.

EW-286 PUR-F-006 RFQ-

(ON STAMP PAPER OF Rs.300/-)

FORM OF BANKER’S UNDERTAKING

(Combined Performance Guarantees (PBG) towards Execution/Supply period and

Guarantee/Warranty period as per Commercial Terms & Conditions of Tender)

We, __________________________________________________(name of the Bank and Address of

the Branch giving the Bank Guarantee) having our registered Office at

registered office) hereby give this Bank Guarantee No.

unequivocally and unconditionally to pay immediately on demand in writing from

the Gujarat State Electricity Corporation Limited, or any Officer authorized by it

in this behalf any amount up to and not exceeding Rs. _____________ (Amount of

Combined Performance Guarantees (PBG) towards Execution/Supply period and

Guarantee/Warranty period) Rupees

Gujarat State Electricity Corporation Limited on behalf of

M/s.___________________________________________________ who have entered into a contract

for the supply / works specified below :

This agreement shall be valid and binding on this Bank up to and inclusive

of___________________(Date of validity of the Bank Guarantee) and shall not be

terminable by notice or by change in the constitution of the Bank or the firm of

Contractors / Suppliers or by any other reason whatsoever and our liability

hereunder shall not be impaired or discharged by any extension of time or

variations or alterations made, given conceded or agreed, with or without our

knowledge or consent, by or between parties to the said within written contract.

“Notwithstanding anything contrary contained in any law for the time being in force or

banking practice, this Guarantee shall not be assignable, transferable by the beneficiary

(i.e. GSECL). Notice or invocation by any person such as assignee, transferee or agent of

beneficiary shall not be entertained by the Bank. Any invocation of the Guarantee can be

made only by the beneficiary directly.”

“NOT WITHSTANDING” anything contained herein before, our liability under this

guarantee is restricted to Rs._______________(Rupees

___________________________________________only). Our guarantee shall remain in force

until _______________ (date of validity of the Bank Guarantee).Unless demands or

claims under this Bank Guarantee are made to us in writing on or before _____________

(Date of validity of the Bank Guarantee), all rights of Beneficiary under this Bank

Guarantee shall be forfeited and we shall be released and discharged from all liabilities

Please mention here complete Signature of the Bank’s authorized

Postal Address of the Bank with signatory with Official Round Seal.

Branch Code, Telephone and Fax

NAME OF DESIGNATED BANKS : As per Annexure - I.

EW-286 PUR-F-006 RFQ-

Financial Department, GR.No. FD/MSM/e-file/4/2025/2712/DMO Dtd. 01/04/2026

[ To be revised as per GoG notification issued from time to time.]

List of Banks Notified by GSECL

(A) Guarantees issued by following banks will be accepted as SD/EMD on permanent

 All Nationalized Banks.

(B) Guarantees issued by following Banks will be accepted as SD/EMD for period up

to March 31, 2027. The validity cut-off date in the GR is with respect to date of

issue of Bank Guarantee irrespective of date of termination of Bank Guarantee.

Name of Banks Name of Banks

1 AXIS Bank 23 A U Small Finance Bank

2 Bandhan Bank 24 City Union Bank

3 CSB Bank 25 DBS Bank India Limited

4 DCB Bank 26 Dhanlaxmi Bank

5 Equitas Small Finance Bank 27 Federal Bank

6 HDFC Bank 28 HSBC Bank

7 ICICI Bank 29 IDBI Bank

8 IDFC First Bank 30 Induslnd Bank

9 Jammu and Kashmir Bank 31 Jana Small Finance Bank

10 Karnataka Bank 32 Karur Vysya Bank

11 Kotak Mahindra Bank 33 RBL Bank

12 South Indian Bank 34 Standard Charter Bank

13 Tamilnadu Mercantile Bank 35 Ujjivan Small Finance Bank

14 YES Bank 36 Ahmedabad Mercantile Co-

15 Nutan Nagrik Sahakari Bank 37 Rajkot Nagrik Sahakari Bank

16 Sarswat Co-Operative Bank 38 SBPP Co-operative Bank Ltd.

17 SVC Co-Operative Bank Ltd. 39 The Cosmos Co-op Bank Ltd.

18 The Gujarat State Co- 40 The Surat District Co-operative

Operative Bank Bank

19 The Surat Peoples Co- 41 The Baroda Central Co-operative

operative Bank Ltd. Bank

20 The Panchmahal District Co- 42 The Kalupur Commercial Co-

operative Bank operative Bank

21 The Rajkot Commercial Co- 43 The Banaskantha Mercantile Co-

operative Bank Limited Operative Bank Ltd.

22 Gujarat Gramin Bank

EW-286 PUR-F-006 RFQ-

GENERAL SAFETY RULES / NORMS” TO BE OBSERVED BY THE CONTRACTOR

All the contractors working in Gujarat State Electricity Corporation Limited Factory

like Coal/Lignite/Gas/Hydro/Pumping Station shall have to strictly observe the

following Safety Rules. Concern principle contractors are responsible for informing &

observance of these rules by their supervisors/contract workers as well as the

owner/supervisors/ workers of sub-Contractors engaged, if any, by them for the work

contract awarded to them. Prior to commencement of the work, Contractor shall have to

submit a written assurance on their letterhead to the concerned Sectional Head / Engineer-

in-charge that they have thoroughly gone through these Rules, have educated their

employees / workers of their sub contractor and will strictly observe the said Rules while

execution of work under work contract awarded to them. They will have to indemnify the

company for any loss or damage / accident / injury to the company’s property / employee

or employee of their own in default of non - observing these rules.

(01) Contractor should issue photo gate pass for their workers from GSECL Factory

Manager as per Gujarat Factories rules, 1963 & details shall be filled up in GSECL

gate pass format as per Aadhar card /Election card id proof & to follow the gate pass

issue procedure through concern department EE & SE, Security Officer,

LWO/IRO/DGM, Factory Medical Officer, Safety Officer/Dy. Safety Officer & Factory

(02) In case of emergency, temporary photo gate pass shall be issued by Security Officer

only for three days with prior permission of Factory Manager only. More than three

days, Permanent photo gate pass procedure shall be completed by contract agency for

their contract workers.

(03) Certificate of Fitness of employment in hazardous process & operations in form no.33

of Gujarat Factories rules, 1963 shall be issued by GSECL Factory Medical Officer for

all contractor workers before commencement of work & examination responsibility

shall be taken by contractor as well as concerned Head of Department .Pre-

employment & Periodical medical examination of contractor workers shall be carried

out in form no.32 from GSECL Factory Medical Officer after every six (06) months of

contractor with their contractor workers. Contractor shall be fulfilled all health

requirements before commencement of work. After completion of medical examination

in form no.32/33, GSECL Factory Medical Officer shall be signed in contract worker

gate pass procedure format.

(04) If work executed outside factory premises, Principle Contractor shall be registered

compulsory under The Building & Other Construction Workers (Regulation of

Employment and condition of service) Act, 1996 and The Gujarat Building & Other

Construction Workers (Regulation of Employment and condition of service) Rules,

2003 before execution the ”building or other construction work” means the

construction, alteration, repairs, maintenance or demolition, of or, in relation to,

buildings, streets, roads, railways, tramways, airfields, irrigation, drainage,

embankment and navigation works, flood control works (including storm water

drainage works), generation, transmission and distribution of power, water works

(including channels for distribution of water), oil and gas installations, electric lines,

wireless, radio, television, telephone, telegraph and overseas communications, dams,

canals, reservoirs, watercourses, tunnels, bridges, viaducts, aqueducts, pipelines,

towers, cooling towers, transmission towers and such other work as may be specified

in this behalf by the appropriate Government, by notification but does not include any

building or other construction work to which the provisions of the Factories Act,

(63 of 1948), or the Mines Act, 1952 (35 of 1952), apply.

(05) Contract worker gate pass will issue after completion of safety induction 3D animation

movie & Training record is to be maintained in IMS/OHSAS training format by TK

(06) As per Gate pass format of GSECL, Safety Officer/Dy. Safety Officer shall be checked

the issue PPE to contract workers as per nature of job, Form no.10 of lifting tools and

tackles, Driving license, Electrical contractor license, Electrical trade qualifications,

Safety induction training, SOP, supervisor qualifications etc. After fulfillment of all

EW-286 PUR-F-006 RFQ-

Safety compliances, Safety Officer/Dy. Safety Officer shall be signed in Contract

worker Gate pass procedure format.

(07) Work Contract shall be completed by principle contractor/agency/person who is

awarded the work order. Subletting of contract shall be allowed only if prior approval

of Power station chief before execution of work. Contractor/agency shall be submitted

the entire subletting contract documents with gate pass application through concern

department EE & SE, LWO/DGM, Safety Officer/Dy.Safety Officer & Factory Manager.

(08) Under The Conditions Framed Under Rule-45 Of The Indian Electricity Rules,

Valid Electrical contractor License shall be submitted to concern electrical department

EE/SE/Electrical Safety Officer/ Safety Officer/Factory Manager at the time of apply

gate pass by agency/party with latest renewal from Chief Electrical Inspector,

Gandhinagar- Gujarat. Electrical License photocopy shall be checked by Concerned

HOD of Electrical Department/Electrical Safety Officer/Dy.Safety Officer/ Safety

Officer/Factory Manager.

(09) As per nature of job/work, Qualified supervisor (Diploma (Electrical/

Mechanical/Civil/C&I) + 3 years experiences or ITI + 10 years) shall be engaged by

contract agency & qualification certificate with experience certificate shall be

submitted to concern EE/SE/LWO/IRO/DGM/ Dy. Safety Officer /Safety

Officer/Factory Manager at the time of apply gate pass.

(10) As per rule 3 of CEA regulation ,2010: Designating person(s) to operate and carry

out the work on electrical lines and Apparatus, Contract person/worker possesses

a certificate of competency or electrical work permit, issued by the Appropriate

Government. That means, Electrical trade Qualification of contract worker/person like

ITI-wireman/ Electrician, Diploma (Elect), BE/B. TECH (Elect), ME/ M. TECH (Elect)

shall be submitted to concern EE/SE/LWO/IRO/DGM, Dy.Safety Officer/ Safety

Officer/Factory Manager at the time of apply for photo gate pass procedure.

(11) As per nature of job/work & during capital overhauling work /Annual overhauling

work /24X7 round the clock work/major shut down work, Qualified Safety

Officer/Manager/Supervisor (BE/Diploma (Elect/Mech/Civil) + PDIS-Post Diploma in

Industrial Safety) shall be engaged by contractor during dangerous

operations/dangerous works as well as day to day dangerous activities, safety

supervision, tool box talk, Safety awareness programme, SOP preparation with

hazards & its control measures with each step , checking of lifting tools & tackles,

hydra mobile crane, Safety precautions, coordination with Safety Department etc.

(12) License of driver shall be submitted with gate pass issue application as per nature of

vehicles & to follow the Motor vehicle Act,1988,the Central Motor Vehicles

(Amendment) Rules,2016 as well as Gujarat Motor Vehicles rules,1989 & driver

license shall be checked every day by security shift in charge before entry in the

Factory premises.

(13) SOP with JSA (Job Safety Analysis) shall be prepared by contractor through

competent person as per GFR, 1963 or Qualified Safety Officer as per GFR, 1963 with

05 years experiences. SOP will review & approve by concern JE/DE/EE/SE/Elect.

Safety Officer/Dy. Safety Officer /Safety Officer/Factory Manager before execution of

(14) It is compulsory to use standard make Personal Protective Equipments (P.P.Es.) as per

the job requirement. Do not work without use of required P.P.Es. Contractor is

responsible to provide standard make (ISI/DGMS/CE/EN/ANSI approved) & to

checked standard/make in PPE issue format by concern JE/DE/EE/SE/Safety

Officer/Factory Manager. Personal Protective Equipments / Safety Gadgets suitable to

give sufficient protection against hazards involved in their work / job to their staff, as

per the job requirement and insist / enforce their workers to put on the same while at

The ongoing work is liable to be stopped at any time if your contract workers/staffs

found working without P.P.Es. Following is the list of various P.P.Es (as per

ISI/DGMS/CE/ EN/ ANSI approved only) to be used for various works / worksites.

In any work, Contractor shall be issued the minimum 06 nos. of PPEs like Safety

Shoes, Safety Helmet, Safety goggles, Mask & Reusable Ear plug, hand gloves to their

workers/supervisor compulsory & it will check by concern section HOD & Dy. Safety

Officer /Safety Officer at the time of gate pass procedure.

EW-286 PUR-F-006 RFQ-

Quality of PPE shall be approved from Safety Officer as per Indian Standard and

International Standard before executions of work or at the time of gate pass apply

List of safety equipments

Industrial Safety Helmet For protection of head against falling objects or

during fall of person from height. Yellow Colour

helmet is used for contract worker with agency

Safety Goggles/welding For protection of eyes against flying particles / dust,

goggles/ chemical splash chemical splash, welding spark, arc, flashover etc.

Full Face shield For protection of face against flying particles / dust,

chemical splash, spark, arc, flashover etc.

Reusable Earplug / Ear For ear / hearing system protection while working in

muffs. high noise level area.

Chemical suit/Gas tight suit For body protection against chemicals, oils, sharp

/Fire proximity suit/FR edged objects, heat, hot objects etc.

Safety Hand Gloves For protection of hands against chemicals, oils,

sharp edged objects, heat, hot metals/objects,

electricity etc.

Safety shoes/ Gum Boots For protection of leg/feet against falling objects,

with sharp edged objects, heat, hot metals/objects,

Oil/Chemical/water/heat/ electricity etc..

Electrical resistance etc.

Safety Belt(full body For fall prevention while working at heights or in

hardness with double depth, working in vessel or in confined space.

lanyard & shock absorber) /

Rope / Life line / Fall

Dust Mask/Respirator with Protection of respiratory system against dust.

Chemical Cartridge Protection against toxic chemical fumes /

Respirator with full face gases/vapors/dust etc.

mask type A2B2E2K2

Trolley mounted Air line Working in oxygen deficient zone or confine space

respirators with full face area

Portable Single gas detector Working in hazardous storage/process area

like Chlorine, Ammonia,

Portable Multi gas Detector Working in oxygen deficient zone & use in entry of

( LEL,O2,CO,H2S,SO2, etc) confine space & Major fire

Automatic voltage detector To check the present voltage or induction voltage of

electrical equipments/ bus/switch gears from

(one) feet distance before starting the any electrical

EW-286 PUR-F-006 RFQ-

Auto darkening welding The new auto darkening welding helmet combines

helmet (EN 379 & EN 175 legendary Speed glass quality and auto darkening

Level-B) with PAPR as per technology with an innovative wide-view grinding

EN 12941:1998, class TH2 visor to give welders an all-in-one solution for more

and AS/NZS 1716 flexibility, precision, and efficiency.

Respiratory System is a combined face and breathing

protection device, for increased comfort and safety in

welding. The unit is equipped with a particle filter

which removes particles from the air. The unit

provides a constant airflow independent of filter

combinations and clogging. The unit can also be

equipped with a gas filter (for example A1B1E1). The

unit supplies air to the head top via the connecting

breathing tube. The airflow creates a slight positive

pressure which together with the sealing to the face

prevents particles and other contaminants from

entering the head top.

(15) All PPEs (as per ISI/DGMS/CE/EN/ANSI approved only) Should issued by

party/agency/contractor to their contractor workers as per nature of job and

allotment of PPE list shall be submitted to Safety Officer, Dhuvaran on his letter head

as per below mentioned format by Contractor before commencement of work through

concerned JE,DE,EE/SE .

Sub: Issue of PEE to Contractor workers

Sub of work Order:

Name of Agency:

Date of Commencement:

Time limit for work order:

Sr. Name Desi Name of Name of PPE IS Make Qt Unit Date Rec

no. of gnati Section :Code of PPE y of eivi

worke on under no. of issue ng

rs work PPE sign

Reusable Ear Pair

Safety Shoes Pair

(16) Shift Security Inspector/Security Officer shall be checked Safety Shoes & Safety

Helmet of all contractor workers at entry gate of Factory Premises & shall entered

contractor workers with Safety Shoes & Safety Helmet with photo ID Gate Pass.

(17) Shift Security Inspector/Security Officer shall be checked validity of Gate pass of all

contractor workers on daily basis.

(18) During the work execution, one trained & competent supervisor of agency should

always remain present at work site. Concern JE/DE of GSECL shall be supervised the

contract work as per SOP .

(19) Approved NABL laboratory calibration certificates of electrical/mechanical/Civil/

C&I/Environment survey/Chemical etc measuring /testing equipments/instruments

which are used during contract work shall be submitted before starting the work &

shall be checked by concern JE/DE/EE before starting work & it’s record shall be

maintained in concern section.

(20) The contractor shall take all the required safety measures prior to commencement of

work on dangerous substances, machineries or area at which cautionary notice is

displayed and obtain “Line Clear” or “Work Permit” through the concern Department /

EW-286 PUR-F-006 RFQ-

Section JE/DE and shall be informed to concern section JE/DE for closed/ returned

after completion of work.

(21) Safety talk/Safety work instructions shall be given to contractor workers by concern

JE/DE regarding hazards of specific work, risk & it’s control measure (mentioned in

HIRA) before starting the job work and records shall be maintained for each & every

(22) Display Safety instructions shall be strictly followed by all workers who are working in

factory premises.

(23) Material Safety Data Sheet (MSDS) of each chemical shall be available with Chief

Chemist/Control room & work related Chemical information shall be taken by

contractor & contractor workers from Concern EE/Chief Chemist before starting of

chemical handling work.

(24) The contractor shall be checked & securely covered or securely fenced any opened

fixed vessel, sump, tank, pit or opening in ground or in floor which, by reason of its

depth, situation, construction or contents ,is or may be a source of danger before

starting the work each & every days or after interval/recess. Contractor supervisor

shall be informed to concerned HOD regarding any unsafe conditions.

(25) Prohibition of smoking, fires, lights, spontaneous ignition substance, matches; fuses,

mobile phone etc are to be strictly followed by all workers who are working in factory

(26) Prior to carrying out welding, gas cutting, furnace heating or any other hot work job,

remove all the inflammable material lying at or nearby worksite or cover it properly by

suitable protective covering. Also, special care shall be taken before carrying out such

job & see that all possible contributing factors to set fire shall be removed / vanished

prior to commencement of the work. Advance intimation shall be given to concerned

section / fire section to commence the work in fire prone areas. They should also

keep ready all the First Aid Fire Extinguishers / equipments & fire extinguishing

media / material like sand / water buckets or other appropriate equipment at such

(27) While carrying out work in confined space or inside vessel, obtain necessary

“Confined Space / Vessel Entry Permit” from concerned department prior to

commencement of the work.

For lighting in such areas, only 24-volt (ISI certified & with proper guard) hand lamp

shall be used. For taking care of the persons working inside the confined space /

vessel, a supervisor / person capable to keep continuous watch on person(s) working

inside, assist them in case of emergency or arrange to get immediate outside help,

shall remain present at entry point. Use full body safety belt without failed.

While working inside sewage, trench or in-depth, a person to warn outsiders /

entrants / passers etc shall remain available near entry point or the entry point shall

be cordoned by a barricaded tape with a cautionary notice. After completion of the

works, all the lids / covers / grills / grits opened, shall be re-fixed / re-placed in the

original position as it were prior to commencement of the work and leave the work

place in safe condition in all respect, so as to prevent accident to fellow workers.

(28) The contractor shall see that he / his persons do not work on or block (by stacking

material, spare parts, tools-tackles, equipments etc), any passages / walkways /

gangways / aisles / staircases / ladders / lifts or any other approaches / roads

leading to plans or its auxiliaries, on which there is traffic movements or possible

traffic movements in case of emergency. Such passages are meant for safe escape in

the event of emergency. If it is utmost necessary to carry out work in such area with

blocking of passage, prior permission of Competent Authority or the Engineer-In-

Charge shall be obtained. To demarcate / declare the area as “UNSAFE”, cordon it

using barricading tape & display suitable caution notice or keep a person to restrict /

divert the traffic on this route through other safe passage.

(29) The contractor shall see that he / his persons do not work on or block (by stacking

material, spare parts, tools-tackles, equipments etc), any passages / walkways /

gangways / aisles / staircases / ladders / lifts or any other approaches / roads

leading to plans or its auxiliaries, on which there is traffic movements or possible

traffic movements in case of emergency. Such passages are meant for safe escape in

the event of emergency. If it is utmost necessary to carry out work in such area with

EW-286 PUR-F-006 RFQ-

blocking of passage, prior permission of Competent Authority or the Engineer-In-

Charge shall be obtained. To demarcate / declare the area as “UNSAFE”, cordon it

using barricading tape & display suitable caution notice or keep a person to restrict /

divert the traffic on this route through other safe passage.

(30) Prior to use power / electrically operated hand tools / equipments / machines /

gadgets like welding machine, hand grinder, hand drill etc, ensure for its safe

operation & use it only if it is found safe to use. Do not use defective, unsafe or

improperly maintained equipments.

The electrical power supply required to run such equipments shall not be taken

directly at their own but shall be obtained through concerned Electrical Maintenance

Departments or their authorized persons or under their observations / guidance only.

The Electrical Section shall provide temporary electrical connection up to contractor’s

Mains Board on which it is compulsory to install mains switch, ELCB & fuses of

adequate capacity. All such equipments shall invariably be earthed adequately to

prevent electrical shock, sparking, short circuit etc. Power cord to be used shall be of

adequate capacity, without any joint & shall consist of earth wire also. Hence, it is

necessary to use adequate capacity 3-wire power cord for single & 5-wire power cord

for three phase power connections. The plugs, receptacles, pins, holders etc shall be of

adequate capacity & safe to use.

All electrical & mechanical equipments / tools-tackles viz. welding machine, cutting

machine, Grinder, Drill, Chain Pulley Blocks, Hook chooks etc required to be used

during work execution shall be of standard make & bear ISI certification mark on it.

The consumables like welding electrodes, grinding wheels / discs etc which has

specific prescribed life span shall not be used in any case if its expiry date is over.

(31) Non-Sparking Non-Magnetic electrical hand tools and tool kits shall be used by

Electrical contractor for safe use in areas where hazardous, flammable, or

combustible vapors, liquids, dusts, or residues may be present in Gas Based power

plant and list of tools and tackles shall be submitted with technical bid. Non-Sparking

Non-Magnetic electrical hand tools and tool kits shall be checked by JE/DE before

commencement of Electrical work.

(32) Before using lifting machines / tackles (like C.P.Bs., Hook chooks, winch, forklift,

mobile crane, EOT crane etc) & its attachments (like D-shackles, slings, U-clamps,

Eye bolts or any fixtures), it shall be checked and used only if found safe to use. Also,

ensure that these are tested, examined & certified in form no.10 by Competent Person

as per the Factory act-1948 & Gujarat Factories Rules and its validity do not expire.

Further, it shall be fixed properly and firmly prior to lifting the weight. Valid Test

certificate of all Lifting machines used by Contractor to be submitted to

Dy.Safety Officer/ Safety Officer before commencement of work through

concerned EE/SE.

(33) Metal Scaffoldings to be used for working at height shall be of adequate size &

capacity. Obtain the work permit when working at height. While climbing on such

scaffolding or working on any structure at height, use of full body safety belt /full

body hardness with double lanyard & Fall arrestor & Helmet is compulsory. It is also

necessary to fasten chinstraps of the helmet.

(34) Contractor or their employee shall not interfere in day-to-day routine plant activities /

works except the work assigned to them, shall not loiter in the areas other than their

work jurisdiction, as well as shall not temper / operate / touch the

machineries/equipments/auxiliaries with which they are not concerned. Also, the

contractor shall strictly instruct their staff for not to sit or take rest at/near/below

running plants, auxiliaries, systems or any place which is risky, hazardous & prone to

(35) The cylinders containing poisonous / toxic or inflammable / explosive gas like

Oxygen, Acetylene, LPG, Hydrogen, Ammonia, Chlorine, CO2 etc shall be handled

safely taking due care. To handle / shift such cylinders a special trolley /cage meant

for it must be used but in no case it should be rolled.

(36) In Gas Based Power station/Hydrogen storage area /Hydro carbon fumes-vapour

generated area, Spark arrestor (as per approved manufacturer of CCOE, Nagpur) shall

be provided on each vehicle by party/agency and it will check by shift security in

charge before entry of vehicles in the factory premises.

EW-286 PUR-F-006 RFQ-

(37) No women or young person shall be employed or permitted to work in Lead-compound

area like battery room etc. as per schedule VI of GFR

(38) No women or young person shall be allowed to clean, lubricate or adjust any part of a

prime mover or of any transmission machinery while the prime mover or transmission

machinery is in motion. Examination or operation of motion machinery shall be made

or carried out only by a specially trained adult male worker wearing tight fitting

clothing as per section 22 of factories act

(39) In all risky job, before start the work, contractor should obtain General Safety Work

Permit through concerned section from Shift –in-charge well in advance.

(40) In case of noticing smoke or fire during their work execution, they shall make

immediate efforts to extinguish / control it and simultaneously inform the Fire Station

Mobile No as well as Station Fire Officer or Emergency Control room no which is

displayed at prominent place of factory like Main Security Gate, All unit control room,

Canteen area, Safe Assembly points, Fire Station, All security gates, Occupational

(41) In case of any injury / accident while working, it shall immediately be reported to

Safety Department through concerned Sectional Head / Engineer. The prescribed

Form No. 21 & ANNEXURE may be obtained from concerned section or Dy.Safety

Officer/Safety Officer.

In case of any electrical accident, it shall immediately be reported to Electrical Safety

Officer through concern Sectional Head / Engineer. The prescribed Electrical

accident form no. A as per electricity act-2003 & Form No. 21 & ANNEXURE as

per Gujarat Factories rules shall be filled up by concern department JE/DE with

written consent of contractor. The Form may be obtained from concerned Electrical

section or Electrical Safety Officer. Electrical accident investigation shall be carried

out by Electrical Safety Officer with Factory Manager.

After any reportable accident, Contract agency shall be submitted the fitness

certificate of injured person with endorsement of GSECL factory Medical Officer to

LWO/Dy.Safety Officer/Safety Officer/Electrical Safety Officer then after injured

person may allow for work.

(42) For any incident occurred but have no injury to any persons should also reported as

per GSECL format and informed to Dy.Safety Officer/Safety Officer as Near Miss

(43) Safety penalty shall be imposed against Offences by contract workers: If any

contract worker worked in a factory contravenes any provision of Factories act or any

rules or orders made there under ,imposing any duty or liability on workers,

contractor/agency shall be punishable with fine which mentioned as under.

Sr. Description of penalty Amount

(i) Work without PPEs Rs.300/- per person

(ii) Work without work Safety permit like working at Rs.1000/- per day

height, confine space entry, hot work etc.

(iii) License of driver as per type of vehicles not Rs.750/- per person

(iv) Welding work without flashback arrestor/double Rs.1000/- per set

gauge regulator set

(v) Operate Portable power tool without ELCB Rs.1000/-per

(vi) Work without qualified Supervisor as per nature Rs.1000/-per day

of job like mechanical, electrical, civil, C&I,

(vii) Work without SOP & JSA Rs.2000/-per day

(viii) Work without test report of lifting machines / Rs.2000/- per

tackles (like C.P.Bs., Hook chooks, winch, forklift, equipment

mobile crane, EOT crane etc) & its attachments

(like D-shackles, slings, U-clamps, Eye bolts or

any fixtures) in Form No.10 of Gujarat Factories

EW-286 PUR-F-006 RFQ-

(ix) Work without Double lynyer Safety belt during Rs.3000/-per person

working at Height work, work without anchoring

in hook/line line

(x) Work without 24 Volt supply in Confine space Rs.3000/-per person

(xi) (a) Grinding machine used without safety Rs.500/-per

guard/machine guard equipment / per set

(b) unsafe welding machine like open body, Knob

without insulation, connection without lug

(c) damaged welding cables/gas pipelines

(d) welding work doing without welding blanket,

(e) electrical supply without 3 pin plug/Industrial

(f) use of damaged electrical wire for lighting/

(g) use of lighting lamp without cage,

(h) use of open halogen tube,

(i) use of damaged PPEs/use of non Standard

(j) Unsafe lifting and handling of gas cylinders

(k) Cylinder handling without safety cap

(l) Temporary connection without ELCB, etc.

During plant visit/supervision of concern JE/DE/EE, SE, Safety Officer/Dy.Safety

Officer, Electrical Safety Officer, Factory Manager, If they will observed any safety

violations as per CO circular/statutory requirements then they must impose Safety

Penalty through office note directly against contract workers/ contract agency and

Office Note process through proper channel to concern Sectional head and Account

head for recovery purpose. Photograph/CCTV footage is to be put up with penalty note

by imposing officer.”

(44) Party will damage any fire equipments or property or machinery in factory during

execution of work, total damage cost will be recovered from party RA bill and recovery

Office note put up by concern HOD.

(45) All the relevant labour and industrial laws shall also be followed compulsorily.

(46) After completion of work, cotton waste, grease, oil, unused material, welding rod

pieces, scrap etc. are to be removed by contractor and scrap shall be deposited to

scrap yard of Main Store.

(47) For performance evaluation of contractor, safety factors of work accident, fire incident

& near miss accident will be considered. Steps can be taken to review the job

assignment up to cancellation for negligence.

(48) Over & above these, contractor shall have to follow all the safety requirements /rules

& regulations / norms and legal provisions laid down in various statutes. Particularly

the provisions of The Factories Act-1948 & the Gujarat State Factories Rules-1963

(Amended up to date), The Electricity Act-2003 & rules, BOCW Act/Rules shall be

followed strictly. The contractor shall also obey the rules / regulations / instructions

of the local Competent Authority for safety & health requirements.

(49) The above rules shall be scrupulously followed and where required, Contractor

/contractor workers may contact to the Dy.Safety Officer/Safety Officer/Electrical

Safety Officer in case of any ambiguity or needs further guidance in this regard.

Chief Engineer (G)

GSECL: Gandhinagar TPS

Dated seal & signature of

Bidder/Contractor

EW-286 PUR-F-006 RFQ-

Terms and Conditions regarding Labour Laws

During the entire period of the contract, the Contractor and his Sub-Contractors

shall at all times comply with all applicable labour laws, rules, regulations,

notifications, and bye-laws issued by the Central Government, State Government, or

Local Authorities. This includes all existing laws as well as any amendments or new

notifications that may come into force during the contract period.

The Contractor and his Sub-Contractors shall, at all times abide by the following

Acts/Statutes related to Human Resources:

1. Factories Act, 1948;

2. Contract Labour (Regulation & Abolition) Act, 1970;

3. EPF & MP Act, 1952;

4. Building & Other Construction Workers (Regulation of Employment & Conditions

of Service) Act, 1996;

5. ESI Act, 1948;

6. Minimum Wages Act, 1948;

7. Payment of Wages Act, 1936;

8. Payment of Bonus Act, 1965;

9. Payment of Gratuity Act, 1972;

10. Workmen’s Compensation Act, 1923;

12. Maternity Benefit Act, 1961;

13. Inter-State Migrant Workmen (Regulation of Employment & Conditions of

Service) Act, 1979;

14. The Building And Other Construction Workers' Welfare Cess Act,

17. The Carriage by Road Act,

The above list is only indicative and not exhaustive. The Contractor shall remain

fully responsible for ensuring compliance with all other applicable labour and

welfare legislations, rules, and regulations in force during the contract.

The following are some of the major responsibilities of the contractor, in addition

to other obligations prescribed under various labour laws, rules, and regulations

issued by statutory authorities such as the State Government or Government of

India from time to time, which the contractor shall strictly comply with during

the execution of the contract.

1) T he F a c torie s A c t,

The contractor should not deploy worker below the age of 18 years and

above 60 year s for the awarded work.

E arn L eave shall be paid to their bonafide contract worker s a s per the

provision s of the F actorie s Act,

Payment of Earned Leave should be made monthly together with wages for

better compliance of law. The contractor shall maintain E arn L eave

R egi s ter in F orm No. 19 a s per the provision s of the s aid Act and

submit the s ame on demand.

All the written regis ters , Performa etc. shall be maintained up to date

and kept ready for inspection at any time or submitted on-time to

the concerned authorities a s per applicability of the Acts by contractor.

2) T he C ontra c t L abour ( R eg ulation and Abolition) A c t,

The C ontractor / Agency shall have to obtain the Labour L icen s e

under C ontract L abour (R egulation & Abolition) Act from the

appropriate authorities before commencement of work. T he contractor

shall maintain a valid labour license under the C ontract Labour

(Regulation and Abolition) Act for employing necess ary man power to be

required by contractor.

The contractor should not be allowed to engage fifty (50) or more contract

labourers without initiating to obtain the labour license under the

C ontract Labour Act. (the s aid number i.e., fifty (50) or more includes

S upervi s or and other staff).

3) Minimum Wa g e s A c t,

EW-286 PUR-F-006 RFQ-

Contractor shall have to make the payment of wages to the Contract Labours

engaged by them, on or before 7th of every month through nearest Nationalized

Bank compulsory, preferably situated in the premises of TPS area in case of all

works contract. The Contractor shall supply copy of Bank Statement duly

stamped by the Concerned Bank as well as debited entry of amount displayed in

the contractors’ own bank account as token of proof towards payment of Wages

through CLIM/prevailing system at relevant time. Apart from Payment of wages

through Bank, Contractors shall have to make all other payments like Advances,

Bonus, Leave Encashment etc. to their labours through bank only and cash

payment/entry will not be allowed.

Wages rates for contract laborers are applicable as per the terms and conditions

of the license. The contractor shall have to pay wages to workers as notified by

the Government of Gujarat from time to time.

Any default to pay the minimum wages to the engaged workers and deprived of

their right to minimum wages payment on or before 7th of each month shall be

dealt as per the provision of labour laws. Recurrence of the same may lead to

cancellation of awarded contract.

4) T he P rovident F und and Misc ellaneou s P rovi s ion s A c t,

The contractor mu s t po ss e ss separate P . F . code on the name of the F irm

/ Agency / C ompany itself for the subject work.

It should be ensured that all the contract labours engaged by contractor

are covered under the provident fund s cheme and employee’s pension

scheme and their contribution mu s t be remitted regularly to the concerned

R P F C . The photoc opies of challan along with E C R in this regards

should be submitted regularly to the U s er Department to enable their

onward billing clearance.

The contractor shall submit along with hi s bill (month wi se)

statement regarding deductions again st employees’ provident fund

and family pen sion scheme in respect of each concerned employee.

Provident fund and family pension s cheme at the rate of 12 % of wages

(or at the rate s made applicable by the Government time to time).

T he contractor’s contribution and hi s workers contribution towards

provident fund and family pension scheme shall deposited by the

contractor with concerned PF Authorities.

5) Wo r k m e n ’s C ompe nsa tio n & E m p l o y e r ’ s L i a b i l i t y I n s u r an c e.

T he contractors s hall have to obtain E mployee C ompen s ation

P olicy under the E mployee s C ompen s ation Act before starting the

work. E mployee C ompen s ation Insurance shall be obtained for all the

workers engaged for the execution of awarded contract. If any of the

work i s sub-letted, the contractor shall ensure that the sub-contractor

take and provide workmen's compen sation and E mployer' s liability

insurance for the labours engaged. Contractor i s liable to pay

compensation in cas e of accidental injury arising out of and in the

cours e of employment a s per the s aid Act and shall bear medical

expen s e s due to on duty accident.

6) T he P ayment of Gratuity A c t,

For better compliance, contractor shall pay amount of gratuity on a monthly

basis along with the payment of wages, calculated on a pro-rata basis per

month, which is equivalent to 15 days’ wages for each completed year of service

for every worker. (* applicable to A R C / B R C work s c ontra c t only)

7) T he P ayment of B onu s A c t,

E very worker shall be entitled to be paid by the contractor in an

accounting year, bonus, in accordance with the provision s of this Act, For

bett er compl ian ce, the con tractor shoul d pay bonus amount on a

monthly basi s along with wag es calculated on a pro-rata basis per month.

Contractor ha s to submit the paid bonus details of it s worker in F orm No.

C a s per the provis ion s of the s aid Act a s and when required by the

Govt. Authority a s well a s by G S E C L .

8) T he Maternity B enefit A c t,

EW-286 PUR-F-006 RFQ-

Contractor shall ensure that entitled female worker should provide

Maternity L eave and other benefits a s per the provision of the s aid Act.

9) T he B uildin g and other C on s tru c tion Workers ’ A c t,

F or any construction work, fall under the definition of S ection

2(1)(d), happening outside / inside the F actory premis es the s aid

act will be applicable and the contractor or it s sub-contractor shall be

liable to comply with the provis ion s framed there under.

10) The contractor shall give preference to existing or local contract

workers for engagement in the awarded contract and shall issue

appointment orders to each and every workers individually at the time

of their engagement during the period of contract and terminate the

same at the end of the each contract.

Follow the mentioned proc edure at ea c h milestone for the

ex ec ution of work s c ontra c t.

11) On C ommen c ement of C ontra c tual Work

1. Before starting the work, the contractor may contact Labour

Welfare Officer / Industrial R elation s Officer for all formalities related

to labour law compliance before commencement of the contract

and onward Labour L aw compliance thereof, s o that later no

dispute will aris e in respect of compliance of labour law s.

2. It i s the res pon sibility of the contractor to ensure that

contractor’s employees maintain strict discipline a s regards

security, methods of s afe working etc, and not to cau s e any

hindrance to s mooth running of power station or in execution of duties

by G S E C L staff. Any laps e in this regard will be viewed s eriou s ly and

if laps e found, contract i s liable to be terminated. If any of

contractor’s staff i s found unsuitable or not behaving properly,

the contractor shall have to remove s uch worker from the work-

site on demand by EIC. To maintain harmonious industrial

relations amongst contract labours i s solely the res pon sibility of

contractor. Any breach of the s ame will be viewed s erious ly.

3. A digital system developed at the request of the agencies working at

the premises of GSECL, is to facilitate them for easy, efficient,

effective management of data, gate passes, attendances, medical

records, Police Verification documents etc related to their employees

/ workers deployed for various works and services against work order

4. On receipt of LOA and before commencement of work, authorized

representatives of the agency shall login in the CLIMS online portal /

prevailing system at relevant time and apply for registration of their

employees / workers uploading all information with required

documents in digital form. Upon completion of due verifications,

clearance by EIC and HR departments, contracting agency will obtain

gate passes. GSECL will only consider documents like wage sheet

duly accepted and signed by individual workers, as per the

engagement/deployment duration/hours of individual worker duly

certified by the agency, being the employer, for the purpose of

payment of bills and HR clearances.

Agency shall be solely responsible for maintaining accurate and up-

to-date data of their workers in the portal/ prevailing system at

relevant time. All statutory compliances under prevailing laws shall

remain the responsibility of the contracting agency. The agency shall

indemnify GSECL against any liabilities arising from non-compliance

of legal provisions or inaccuracies in the data maintained by them in

the digital portal of CLIMS/prevailing system at relevant time.

5. The C ontractor who intends to engage labours more than the

specified limit under law, then necess ary - F orm No. V under the

Contract Labour ( R & A) Act, 1970 or F orm No. VI under the

EW-286 PUR-F-006 RFQ-

Interstate Migrant worker (employment regulation) Act 1979 a s

applicable i s to be obtained for the purpos e of obtaining Labour

L icen s e from the Licen s ing Authority.

6. It shall be the duty of the Contractor or hi s S upervi s or to ensure

Bio-Metric punching and reporting at the location of work.

7. The contractor shall employ adequate number of experienced staff

at s ite for daily s upervision and for maintaining of various regis ters

and records required under the Labour law s and contracts. No

payment for s uch supervision shall be admissible.

8. The gate pa ss e s obtained for any specific work order will be valid

for that specific work order only and contractor should not divert the

man power for any other work order. If any work or part

thereof i s desired/required to sublet, the contractor shall obtain

the necess ary permiss ion of EIC in black and white well in advance

which i s mandatory for considering the statutory documents of

agency other than the agency who awarded work order.

12) During C ontra c tual Work under the pro g re ss:

1. All C ontractor s shall have to make the payment of wage s to the

Contract Labour s engaged by them, on or before 7th of every

month through Nearest Nationalized B ank compulsory, preferably

situated in the premis es of power station area. T he

Contractor shall supply copy of B ank S tatement duly stamped

by the C oncerned Bank a s a token of proof towards payment of

Wages through CLIMS / prevailing system at relevant time.

2. All C ontractor s ha s to comply & maintain statutory documents /

regis ter s under the provision of labour law s & E P F Act.

3. In cas e the contractor having more than one contract in the s ame

T P S , the contractor shall have to obtain work order wi s e

separate G ate P a ss e s and s ubmit the same with the documents of

statutory compliance that too work order wi s e every month to the U s er

Department to enable their onward billing clearance.

(13) CONTRACTOR TO INDEMNIFY THE GSECL REGARDING

T he contractor shall indemnify and keep indemnified the G S E C L

and every member, officer and employees of the G S E C L , al s o

Engineer-in-charge and hi s staff against all actions, proceedings,

claims, demands, co s t s and expen s e s whatsoever arising out of or in

connection with the matter referred in above claus e s and elsewhere and

again st all actions, claims demands, co s t and expen s e s which may

be made against the G S E C L by any workman/ employees of

contractor or any s ub - contractor and or from any liability any wis e to

any workman/employees of the contractor or sub-contractor under any

laws , rules or regulation having in force of law including but not limited

to claims against the owner under employee compensation Act,

T he E mployee’ s Provident F und Act.1952, and/or the contract

labour (Abolition and Regulation) Act,

T he G S E C L shall not be liable for or in respect of or in consequence

of any accident or injury to any workmen or other pers on in the

employment of the contractor or hi s sub-contractor, and the contractor

shall indemnify and keep indemnified the G S E C L against all

s uch damage and compensation and against all claims,

demands proceedings co s t s , charges and expen s es whatsoever in

res pect of or in relation thereto.

The contractor shall at hi s own expense / ris k and co s t to comply with

all the labour law s a s above- m e n t i o n e d and keep the G . S . E . C . L .

indemnified in respect thereof.

G S E C L : shall be entitled / empowered to deduct directly from the bills

the amount to be paid to engaged bonafide contract workers or the

contract workers engaged by Sub-contractor; any s um or s um s

EW-286 PUR-F-006 RFQ-

payable by main contractor / sub-contractor and which s um /s ums

the C orporation i s required to pay in capacity of Principal Employer on

account of the default

of contractor in respect of all liabilities incurred out of non-

compliance regarding any provision s of Labour L aw s and s ame

amount shall be recovered from the pending dues of the contractor with

15 % administrative charges.

Any other rules and regulation, conditions, circulars etc., that are in

force at pres ent and that may be framed by the G S E C L from time to

time in connection with contracts will be binding and acceptable to

The above are s ome of the major liabilities of the contractor in addition to

other liabilities prescribed under the various labour law s in force from

time to time from S tatutory Authorities like S tate Government /

Government of India, which the contractor shall have to comply with.

The contractor shall provide the name of authorized representative, as

provided to other statutory Government authorities and will be notified

to Engineer In-Charge time to time.

14) Submission of Statutory documents to ensure the compliances:

The contractor shall upload statutory documents, work order-wise, under

Labour Laws and EPF in CLIMS / prevailing system at relevant time.

Required document s shall be u p l o a d e d by the contractor in existing

portal /prevailing system at relevant time invariably each month to

Engineer In-Charge for onward process and smooth clearance by HR

List of documents required for gatepasses of contract

workers t hrough clims /prevailing system

Sr. No. Description of documents attached

Copy of Work Order

2 Copy of P. F. Code No.

Insurance Policy as per subject of work order under the Workmen

Compensation Act,1923

Contract agreements/ subletting work contract documents with

Copy of Id proof of Aadhar card or Election voting card or driving

license or Passport only

6 Copy of Police Verification in respect of each contract workers

15. The contractor whose work order value is above Rs. 5 lacs shall have to

submit “Declaration cum Indemnity Bond” on Rs. 300/- Non-Judicial

stamp paper in prescribed Performa (Annexure- “B”) with Agreement and

Indemnity Bond before the commencement of the contract.

N PROCURE- PUR-F-006 RFQ-

Annex ure- “ B ”

D E C L A R A T I O N C U M IND E MNI TY B OND

( On Rs.300/- Non J udi c ial S tamp Paper duly notarised)

T HI S D ECL A R A T IO N C UM IND E MNI TY B OND made at -------------------------

(mention location) by M/S. ------------------------- having it s R eg. office at---------

---------------------------------------------(hereinafter referred to a s “C ontractor”

which expre ssion shall unle ss it be repugnant to the context or meaning

thereof, be deemed to mean and include their respective a ss ign s , successors

executors, subcontractors and / or administrators) of the ON E P A R T in favour of

M/S Gujarat S tate E le c tri c ity Corporation L imited having it s power

S tation at … … … … … . . T h e r m a l P ower S tation (hereinafter referred to a s

the “C ompany” ), which expression shall unle ss it be repugnant to the

context or meaning thereof be deemed to mean and include it s a ss ign s

s ucce ss or s ) of the O T H E R P A RT .

W H E R E A S the C O M P AN Y ha s entered into a contract with the C ontractor for

--------------------- dated-------------------------“hereinafter called the “Contract”);

AND W H E R E A S it i s one of the ess ential conditions of the C ontract that the

Contractor shall comply with all the provisions of the Labour & Industrial

L aw s , a s may be applicable from time to time for the discharge and

completion of the works and completion of the Works and S ervice s covered

under s aid Contract Labour ( R & A) Act 1970,Child Labour (Prohibition and

Regulation) Act 1986, The E mployee s Provident F und s & Miscellaneous

P rovi s ion s Act,1952,Employees S tate Insurance Act 1948, Minimum Wages

Act,1948,Payment of B onu s Act,1965,Payment of Wages Act,1936, E mployee s

Compen s ation Act.1923, F actorie s Act,1948 and other Labour L aw s , R ule s

Notifications and C ode s which are at pres ent applicable to the contractor and

which may be applicable during the tenure of the contract (hereinafter referred a s

the ‘ L aw s ’).

AND W H E R E A S the C ontractor ha s agreed to execute thi s Declaration cum

Indemnity B ond to thi s effect and ha s agreed to indemnify and Company, it’s

Directors, Officers and employees and representatives indemnified and hold

harmle ss against all third party claims, charges ,penalties, fines, expen s e s

,lo ss e s , damages co s t s , s uit s or any other levy against the C ompany and/or

the management due to the failure of the C ontractor to observe or follow all

applicable law s.

NOW T HI S D E E D W I T N E S S E T H A S UND ER

1. T he Contractor hereby declares that all act s, deeds, actions, activities,

conduct and lapse, delays, mi s deed s , faults, breaches, inactions etc done by

hi s a ss ign s , s ucce ss or s , executors, subcontractor and / or administrators

shall be construed to be have been done by the contractor and he

alone shall be liable for s uch act s, inactions etc.

2. In consideration of the C ompany awarding the Contract to the

Contractor subject to the condition of execution of thi s Declaration cum

Indemnity bond, the Contractor declares and repres ents to the C ompany

that the Contractor ha s obtained all Statutory registrations, Certificates

licen s e s and approvals required under the L aw s enabling the Contractor

to execute the Contract in a legal and lawful manner.

N PROCURE- PUR-F-006 RFQ-

3. That in the event of any liability arising out of non-compliance of any ‘Laws’ of the land

by the Contractor in connection with the Performance of the contract, the

Contractor shall bear all the resultant liability (ies) whatsoever, if any and that the

company , its Directors, Officers and employees, representatives, shall not be liable for

any such liability(ies). The Contractor undertakes to indemnify and keep the

C ompany and it s Directors, Officers and employees, representatives

indemnifies, defend and hold harmle ss , against all lo ss e s , co s t s

damages, claims, penalties, interest, expen s e s , demands, fines, legal

liability, cau s e s of action, injury to per s ons , s uit s etc., which may be

suffered, incurred, undergone and / su s tained by the C ompany including

the C o s t s and expen s e s that may be incurred in defending any s uch

liability(ies) claim( S), Proceeding ( S ) etc. that maybe made or taken or

taken or aris e on the s ame by any P er s on, body, authority,

government, judicial / quasi - judicial authority due to the failure

or non-compliance of any s uch law s and rules there under (including any

amendments in act s, law s, s tatute s & rules there under) of whatsoever

kind and nature arising out of or in any way connected with, whether

or not s uch act s or omi ss ion s are actual or alleged, active or pa ss ive

with regard to the discharge of the s aid Contract.

4. T he Contractor further declares that in cas e of any s uit / claim / right

/ damages / compensation / fine / levy / charges / expen s e s / lo ss e s

/ penalties / co s t s raised by the third party, including contract

labours engaged by the contractor, he s hall join s uch proceedings in s uch

Suit/Court/Tribunal/Authority and effectively defend the s ame.

5. T he Contractor hereby agree and undertakes to make good any

lo ss , damage, claims, s uit s , demands, decrees, expen s e s that the

C ompany may suffer to the fullest satisfaction of the C ompany and if

the C ontractor fail s to make good the s ame then the C ompany shall

have the right to recover the s ame from and or any other lo ss

sustained, without any restriction or limitation, together with any other

incidental expens e s , co s t s , and all incidental logistic expen s e s etc that

may be suffered by the C ompany from the Contractor and the Contractor

hereby further confirms and declares that thi s Declaration cum

Indemnity B ond i s irrevocable and shall be final and binding on him,

his heirs, executors, administrators, legal representatives, s ucce ss or s

subcontractors and a ss ign s , wherever the context applies. any claims,

demands, shall be adjusted against any amount due and payable to the

Contractor and the C ompany shall have the right to withhold any

amounts due and payable to the Contractor, till the settlement of s uch

claims, di s pute s to the Contractor towards discharge of s uch claims,

obligations etc.

6. T hi s Declaration cum indemnity bond shall be in accordance with the

law s of India and any dis pute between the parties with regard to thi s

Declaration cum Indemnity B ond shall be resolved through the dis pute

resolution proce ss mentioned in the General C onditions of the Contract

IN W I T N E S S W H E RE O F , the s aid Contractor ha s hereunto s et their hand the

day and year first hereinabove written.

S I G N E D S E A L E D AND D E L I V E R E D B y the within named “C ON TR A CT O R”

N PROCURE- PUR-F-006 RFQ-

(Authorised Signatory)

R ubber S tamp of Firm/C ompany

In pres en c e of Witne ss

Name & Addre ss of Witne ss S i g nature

Residential Address:

Residential Address:

N PROCURE- PUR-F-006 RFQ-

GUJARAT STATE ELECTIRICITY CORPORATION LTD., GANDHINAGAR

TENDER & CONTRACT FOR WORKS

GENERAL RULES AND DIRECTIONS FORTHE GUIDANCE OF CONTRACTOR

Notwithstanding anything contained to the contrary in the specification or tenders in

subsequent exchange of correspondence, the conditions of contract shall be binding

on the contractor and any change of variation expressed or implied however made in

the said conditions shall not be however valid or operative unless expressly sanctioned

by the corporation The contractor shall be deemed to have fully informed himself and

to have special knowledge of the provisions of the conditions of contract herein

1. All works proposed to be executed by contract shall be notified in one of the

English and one of the vernacular local daily newspapers stating the work to be

carried out as well as the date for submitting and opening tenders and time

allotted for carrying out the work also the amount of earnest money to be

deposited with the tenderer and the security deposit to be deposited by the

successful tenderer.

2. Copies of the specifications, designs drawings, estimated rates. Schedule rates and

any other documents required in connection with work which will be signed by the

Executive Engineer for the purpose; of identification shall be open for inspection