CA NO GE(N)AMB-08/2024-25 WELCOME MAINT , DAY TO DAY MAINT AND REPAIR TO JOINERY, PLUMBING, SANITARY, ROOF, PLASTERING, CERTAIN E/M WORKS AND OTHER CONNECTED BLDG REPAIR WORK IN MD OFFRS ACCN AND OTHER AREAS OF AGE B/R-II UNDER GE (NORTH) AMBALA

Amount

Schedule 'A' Part-I (B/R itmes) Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key scrubbing down with water, etc. complete all as specified and as directed by the Engineer-in-Charge

Dismantling of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar, etc. but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for brick work with sub class B bricks old size bricks, straight or curved on plan any radius in cement mortar 1:4 in half brick thick wall complete all as specified and as directed by the Engineer-in-Charge.

Material and labour rendering 15 mm thick on brick work or concrete wall surfaces in cement mortar 1:4 including mixing water proofing compound @ 2% by weight of cement or as per manufacturer's instruction and finished fair and even without using extra cement complete all as specified and as directed by the Engineer-in-Charge. ( Note- The cost of providing WPC shall be included in quoted rate under this item )

Material and labour for rendering 10 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:6 and finishing the surface even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering 05 mm thick on fair faces of brick work or concrete ceiling surfaces, chajjas, etc. in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine stone aggregate of size between 6 to 12 mm as per the texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered/unplastered surfaces of walls, chajjas, roof projection, etc. and applying two coats of cement base paint complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of newly plastered/ unplastered surfaces of walls and applying two coats of oil bound distemper with painting roller over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered/unplastered surfaces and applying three coats of white lime wash on surfaces of walls, chajjas, roof projection complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair mild steel powder coated wooden finish curtain rod 25mm dia fixed with and including decorative brackets, two lotto for each rod length at both end, etc. fixed with stainless steel screws complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing PVC connections 15 mm size and 600 mm of length with PTMT nuts and PVC washers on both ends as in repair complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

Material and labour for galvanised iron tubing 15mm bore, ISI marked, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Material and labour galvanised iron tubing 20 mm bore, ISI marked, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair bib tap 15mm bore fancy type brass chromium plated with long body, ISI marked, wall flanges and capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair fancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, ISI marked, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement as in repair complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing as in repair 15mm bore, cast copper alloy, fancy type, chromium plated, ISI marked, stop valves screwed down, high pressure with capstan head, screwed both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair brass chromium plated tubular towel rail, 20mm dia, 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair 15mm bore cast copper alloy chromium plated angular stop valves, ISI marked, screwed down, high pressure with capstan head, screwed down both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of vitreous china wash hand basin white with pedestal, ISI marked, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling chromium plated and 32 mm dia PVC waste pipe including fixing of waste fitting, etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair vitreous china squatting pan, Orissa pattern, 580 mm x 440 mm size, white colour with integral foot rest and PVC SWR 'P' or 'S' trap of pressure rating 6 Kg per square cm complete including provision of cement concrete bedding, connection to trap, outgoing flushing pipe, anti syphonage pipe, etc. complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in replacement 10 litre PVC valveless syphonic action type flushing cistern with inlet ball valve float, handle, etc. with and including brackets, flush pipe, etc. and connections of flush pipes to WC complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing for vitreous china wash down water closet pan (pedestal pattern), white (including fixing bolts but excluding flushing cistern and flush pipe) including plastic water closet seat white closed pattern with flat bottom cover and mild steel chromium plated or aluminium hinges device as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of brass chromium plated toilet paper holder complete fixed to wall as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of sinks with drainage board made out of stainless steel 1mm thick sheet for kitchen with plugs, waste pipe, brass chromium plated coupling and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm as in repair complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing of plastic water closet seat cover , white closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hinging device as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of PVC cabinet type looking mirror size 450 mm x 600 mm box type including all necessary items as in repair complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Non Skid coloured ceramic tiles joint free premium/1st quality 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Non Skid coloured ceramic tiles joint free premium/1st quality of same description as of floor tiles in serial item No. 34 above but 100mm to 200mm height as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for glazed ceramic coloured tiles joint free premium/1st quality in vertical surfaces/skirtings/dados of size 300x450 x7mm or 300x 600x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for vitrified ceramic tiles light shade,1st quality,(square/ rectangular), 10mm thick, area of each tile exceeding 0.36 sqm and not exc 1.00 sqm as in floor, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for vitrified ceramic light shade tiles, 1st quality, of same description as of floor tiles in serial item No. 37 above but 100mm to 200mm height as in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including rendering 10 mm thick in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 25 mm thick PCC 1:2:4, type B0 as in sub base of floor (using 12.50mm graded crushed stone aggregate), finished even & fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge. Note- This item shall not be executed in the location, where dismantling of tiles work have been done.

Material and labour for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in horizontal surface of steps, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 including rounding of front edge/exposed edge complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rounding to edges of stone slab, both edge with grinder as in kitchen slab, steps and similar situations etc. complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of boarding of any type/ size as in CB / Wardrobes or fixed in any position including hardware (if any), etc. complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 18mm thick lead free PVC celuka ply of both side plain white colour having density 600 Kg/Cum, fixed with screws, solvent cement / adhesive to make kitchen / bed rooms cabinet sides, top and bottom and shelves inside the cabinets complete all as per manufacturer's specifications/ instructions complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of Continuous (piano) hinges, width of flaps 30mm mild steel, bright finish or electro galvanised complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 40mm dia brass polished cupboard knobs fixed with nut, screws and washer of stainless steel complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of magnet catcher fixed in cabinet shutter (one portion) and wooden frame (other portion) with screw complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutter area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutter area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description area not exc 2 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for factory made 2nd class hard wood 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both face . The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters,open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be kiln seasoned and chemically pressure treated) complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of stainless steel wire cloths 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair stainless steel wire cloths 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair of galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of apertures 1.18 mm and fixed with tinned tack or galvanised wire staple complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of solid PVC door frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on single side used instead of plain colour PVC sheet reinforced with MS square tube, edges will be painted to match with prelaminated sheet and fixed in opening complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of factory made solid PVC moulded door shutters with particle board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick prelaminated moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-290-W (Gde E-165) quality 'A' complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate as in holdfasts complete all as specified and as directed by the Engineer-in-Charge.

S&F double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutter fabricated from following sections :- (a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf . (c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mm made from 1.25 mm thick MS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt stove enamelled 150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf

item No. 59 (contd....) vi) Pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c welded to frame . (viii) Two coat of Synthetic enamel paint over one coat of red oxide primer. (ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws . (x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window. (xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessories as mentioned above. (iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds and steel window frame glazed with putty or fixed with beads complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified by the Engineer-in-Charge.

Supply and fixing of 150 mm long aluminium handle, cast type, anodised complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 200 mm long, aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 250mm long aluminium alloy, anodized, sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloys to door shutter complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of butt hinges 100mm long of stainless steel, medium weight, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of mild steel helical door spring 150 mm long fixed with screws to wooden chowkats or welding to steel chowkats, complete all as specified and directed by the Engineer-in-Charge.

Material and labour for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 32 mm dia PVC waste pipe of standard length for wash hand basin / Kitchen sink etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of brass chromium plated double lever basin mixer with out popup and 450 mm long braided hoses for 15 mm bore pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of corner Glass shelf 300 mm (with brass bracket) including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 110mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and directed by the Engineer-in-Charge..(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 110 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 75mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 75 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified. (Note- UPVC bends shall be confirm to BS 4515 DIN 19531 and DIN 19534)

Dismantling water tanks of capacity exc. 250 litre and not exc. 500 litres and removing from site complete all as specified and as directed by the Engineer-in-Charge.

Dismantling water tanks of capacity exc. 500 litre and not exc. 1000 litres and removing from site complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing water storage tank, 1000 litre capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm bore high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing water storage tank, 500 litre capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm bore high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore, complete all as specified and as directed by the Engineer-in-Charge.

Demolition and breaking up drain pipes 75/100 mm dia, SGSW, AC, PVC, reinforced concrete pipe including fittings, in any position complete all as specified.

Supply and fixing of 15 mm bore Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe as in repair, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repairs, stainless steel towel rack size 600 mm long with lower hanger complete all as specified and as directed by the Engineer-in-Charge.

Cutting chases to brick wall built in cement mortar, pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for cleaning and removing all scale and dirt etc from PVC/RCC tanks and mouths of circulating pipe of capacity 250 litre and upto and including 1000 litre & writing on the tank with synthetic enamel paint not less than 70mm long and 2mm wide of words in shape like cleaned on : 15.06.2018 complete all as specified and as directed by the Engineer-in-Charge. NOTE :- The unit rate shall be included cost of small fittings such as elbow, socket, reducer, tee, union, etc.

Supply and fixing of stainless steel fancy type peg set ( each peg having 5 Nos hook) and fixed with stainless steel screws and PVC rawal plug as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of brass chromium plated wash hand basin mixer for mixing hot and cold water screwed down for 15mm dia pipe including waste popup with 450mm long braided hoses and all connecting fittings as in repair complete all as specified and as directed by the Engineer-in-Charge. Make :Jaquar Cat Part No QQP-7167BPM / Cera Cat Part No.F2007461 / Hindware Cat Part No.F 480011 equivalent make mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of as in repair brass chromium plated concealed stop cock with long shank and wall flange screwed down,high pressure with crutch handle, screwed down both ends for iron pipe or for unions 15mm bore complete all as specified and as directed by the Engineer-in-Charge. Make:- Jaquar Cat part No.CON-083FTK or Hindware Cat part No. F280027 or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of brass chromium plated wall mixture 3-in-1 system with provision for both hand shower and overhead shower complete with 115 mm long bend pipe, connecting legs and wall flange without hand and overhead shower as in repair complete all as specified and as directed by the Engineer-in-Charge. Make :Jaquar Cat Part No QQT-7309 /Hindware Cat Part No.F120019 or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of brass chromium plated soap dispenser with glass bottle as in repair complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of brass chromium plated Towel ring round including fixing with brass screws complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ACN-1121BN/Cera Cat Part No.F5007105 / Hindware Cat Part No.F 880007 or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of brass chromium plated Soap Dish Holder including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ACN-1131N/Cera Cat Part No.F500716 / Hindware Cat Part No.F 840006 or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of overhead shower 200mmx200mm square shape single flow ABS body chromium plated with grey face plate with rubit clean system as in repair complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of brass chromium plated hand shower ( health faucut) with 8 mm dia 1.2 mtr long flexible tube and wall hook with NRV ( back flow preventer )complete fixed to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ALD577/Cera Cat Part No. F8030101 or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of counter top vitreous china wash hand basin white of size 515mmx365mmx120mm, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting, etc. as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No FLS -WHT-5931 /CERA Cat part No.S2020108 /Hindware Cat Part No.91041 or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of single piece water closet wtih PP soft close seat cover, hinges, fixing accessories and accessories set, cistern fittings, S or P Trap complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No SLS -WHT-6855S /CERA Cat part No.S10131095 /Hindware Cat Part No.20085 (S-30) equivalent make mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of brass chromium plated toilet paper holder including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : AKP-35753PS/Cera Cat Part No.F5007109 / Hindware Cat Part No.F 840009 equivalent make mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of aluminium (Die-cast) body hydraulically door closer regulated, designation No.3, universal type, suitable for door shutters of 851 mm to 1000 mm in width and weight between 61 to 80 Kg as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty as in repair complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for repairing of all type aluminium window/door shutter with frame and refixing it after re-securing its frame work by means of tightening with new screw ,cleats, rubber gasket and refixing in the same opening complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair of 5mm PVC hollow sheet (the thickness of inner wall 0.7 to 1.00mm) wall panelling inclusive of solvent cement and fixing at site with U clip or PVC frame as per specifications and drawing complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of old decorated brick/concrete, plastered / unplastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white lime wash on prepared surfaces of ceiling etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of old decorated brick/concrete, plastered / unplastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper with painting roller over prepared surfaces of ceiling etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper with painting roller over prepared surfaces of walls pillars, cornices etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for complete removal of existing treatment from wall by scrappers or any other means and washing , rubbing down and stopping complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for one mm thick wall care putty white cement based in two or more coats to achieve smooth surface over prepared surface complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of putty surfaces and applying two coats of oil bound distemper with painting roller over prepared surfaces of walls, pillars, cornices etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour applying two coats of plastic emulsion on interior surface of walls of any description over 10cm girth or width, not other wise described using painting roller after preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls complete all as specified and as directed by Engineer-in charge .

Material and labour preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of cement base paint on the wall, pillars, cornices etc complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of cement base paint on the wall, pillars, cornices etc complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

Schedule 'A' Part-II (E/M itmes) Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, regulators, socket outlet, etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly (boxes shall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally) including provision of new covered plate over sunken box for housing the modular switches , modular socket outlets,modular fan regulators etc. for one light/fan/exhaust fan/bell point controlled by one way switch, complete all as specified and as directed by Engineer-in-Charge. Note :- a) .All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid for separately .

Description all as per serial item No.115 here-in-before but for One 3 pin, 6 Amps, socket outlet controlled by one switch on independent board, complete all as specified and as directed by Engineer-in-Charge.

Description all as per serial item No.115 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on same board, complete all as specified and as directed by Engineer-in-Charge.

Description all as per serial item No.115 here-in-before but for one socket outlet 16 Amp with 2.50 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade, ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular switch 1 module, single pole, one way 16 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular socket outlet 2/3 pin combined, 6 Amp, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular socket outlet 3/3 pin combined, (6pin), 6/16 Amp, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of ceiling rose surface type 2/3 terminal polycarbonate, isolated body complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair of modular bell push 6 Amp, 1 way, 1 module, 230 volts complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair, of calling bell ding dong 230 volt, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair, electronic Fan regulator modular 100 watt, 1 module, 230 volts , 50 Hz, AC supply suitable for ceiling fan any type/make/sweep complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair, switch piano, flush type, single pole, one way, 6 Amp ,complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair, bell push 6 Amp, flush type complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair, socket outlet 2 in 1, 3 pin, 6 Amp, flush type complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair, switch piano, flush type, single pole, one way, 16 Amp,complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair, indoor decorative LED tube light fitting box type 18/20 watt with electronic driver, opal diffuser, high efficient aluminium housing body suitable for LED tube, high efficient, AC 220-240 volts, 50 Hz including 18/20 Watt LED tube rod luminaries environment friendly, high efficient, T8 with aluminium extrusion heat sink and connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair LED batten fitting 10-12 watt, 2 feet, PVC housing with electronic driver including tube rod 10/12 watt cool/warm type industrial model complete, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair, LED surface mounted bulk head luminaries 8-10 watt with min 800 lumen, industrial model, IP 65, PVC housing, surge protection including driver and LED lamp, etc. complete with all accessories, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair, 9/12 watt LED light fitting wall mounting fixture (sketch type) including LED lamp compact and energy efficient epoxy powder coated luminaire and connecting with copper conductor flexible cable from ceiling rose to connector of the light complete including removing unserviceable light fittings complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair, LED Bldg Security Light Fittings of capacity 20 -25 watt made up of die cast aluminium housing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver, service bracket of mild steel pipe 32 mm bore medium grade of length 0.9 mtr with MS clamps, bolts, nuts, and washers and suitable reducer for connecting fitting to MS pipe as required at site and two coats of synthetic enamel paint over one coat of red oxide primer on mild steel work and making electrical connection, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair, electronics energy meter 10-60 Amp, 240 volts, 50 Hz, single phase with backlit LCD display, large digit with temper indication icon available on LCD including parameter to show data time time, current, reading, load, PF, voltage, KWH, etc. confirming to IS, IP-54 with Basic current 10 Amps, class of accuracy 1.0 as per IS 13779: 99CBIP tech report 88 including transparent pilfer proof meter box, made by Engineering plastic, complete all as specified and as directed by the Engineer-in-Charge.

Supply and laying in repair sub main wiring with two run of 4 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 4 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked, multi stranded copper conductor as earth continuity conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium grade, ISI marked of adequate size for housing the wires complete all as specified and as directed by the Engineer-in-Charge. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

Supply and laying in repair sub main wiring with two run of 6 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked, multi stranded copper conductor as earth continuity conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium grade, ISI marked of adequate size for housing the wires complete all as specified and as directed by the Engineer-in-Charge. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

Supply and fixing in repair MCB SPN, 6-40 Amps, 240 volt,10 KA, 'B' curve, ISI marked, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair MCB SP, 6-32 Amps, 240 volt,10 KA, 'B' curve ISI marked, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB.20 Amp, 10 KA 'B' curve complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair heating element, cup or triangle type of 2 KW as required at site for geyser of any make and any descriptions complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair thermostat switch for geyser of any type, ISI marked, I complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair PVC connection pipe 600mm long having wire mesh coating over it with brass nuts and washers suitable for connecting geysers inlet and outlet to GI tubing complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair gang box 3 module surface type suitable for mounting of 6 /16 switch and socket complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair sheet metal enclosure, 2 way without busbar, single pole neutral along with MCB DP 10 Amp, complete all as specified and as directed by the Engineer-in-Charge.

Supply and laying in replacement 1100 Volts grade heavy duty, passing through pipe, two core, 6 Sqmm nominal cross section, PVC insulated sheathed aluminium conductor with inner sheathing of PVC tape and overall PVC sheathed in service connection, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair heavy duty exhaust fan 300mm sweep with corrosion resistant metallic body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings, aerodynamically contoured blades, metallic base frame with rubber mountings for silent operation, 6 pole, maximum watt input not more than 45 watt, 1400 RPM, minimum air delivery 6200 cum/hr with metal blades and shutter type louvres self-openable/ closable for protecting the entrance of birds as per IS :2132-1967 and testing complete all as specified and as directed by Engineer-in-Charge.

Supply only flexible cable PVC insulated and sheathed, 2 core, circular multi stranded copper conductor of 23/0.076 Sq mm including removing unserviceable cable, complete all as specified and as directed by the Engineer-in-Charge.

Note:- Amount of credit of Rs. 1,01,035.00 for retrieved materials is mentioned in Schedule of Credit Page No. 146 (R) to 148 (R) of tender documents in pdf form which will be deducted offline while acceptance of tender.

Durga Enterprises

bhagwandasswazirchand

Parveen Kumar

SMT Construction