Providing new panel board in place of old feeder pillar box at south west corner of Asthana Mandapam and new sump room at EO quarters belongs to SVVSD, Kanipakam

Supply Installation Testing and commissioning of free standing floor mounted dust and vermin proof compartmentalised cubical panel made out of CRCA sheet, required hardware, duly painted by two coats of zinc/red oxide primer followed by Powder coated / epoxy / PU painted with phosphatisation in grey or required shade after rinsing. The panel having PU/Neoprene rubber gasket of not less than 3mm thickness,separate detachable, gland plate M.S. base channel, hinged door with locking arrangement for equipment/switchgear. Thickness of sheet shall not be less than 1.6mm up to 600mm length/width of any compartment and be of 2.0mm above 600mm. Load bearing structure shall be of 2.0mm thick sheet supported by base M.S. channel if required. Side walls and cable alley compartments having bolted type doors with detachable extension type structure

Supply and fixing of electrolytic grade aluminium bus bar of 25mm x 6mm thickness (0.402kgs/mtr) by means of SMC / DMC type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves

Supply and Fixing of (0-500) V range Volt meter on existing panel ,\ making connection by PVC insulated copper conductor with PVC sleeves / channel etc. as required.Makes : L&T

Supply and Fixing of Current Transformer from 200 / 5 to 400/5 Ratio , 10 VA , class 1 accuracy, with all necessary support in existing panel including connection etc. as required Makes : L&T

Supply and Fixing of 240/220 V, LED (22.5 mm dia ) Pilot lamps of red and yellow colour with integral circuit, terminal block, including connection etc. as req

Supply and Fixing of 240/220 V, LED (22.5 mm dia ) Pilot lamp of blue colour with integral circuit, terminal block, including connection etc. as req

Supply and making end termination with heavy Alluminium lugs (pin/ ring type) as per IS specification duly crimped with crimping tool, PVC tape etc of 50 sqmm makes:Dowels/ Jainson/ Comet

Supply and making one end termination with heavy duty single compression brass gland as per BS 6121:2005 ,IP 66 complete, SIBG type, heavy duty Alluminium lugs of size 3.5 coreX 50 Sqmm duly crimped with crimping tool, PVC tape etc for of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as equired of size.Makes:Dowels/Comet/SMI)

Labour charges for laying of U.G cables up to 50sqmm on wall with necessart fixing arrangements such as saddles , clamps including cost and conveyance of all materials and labour charges etc., complete

Labour charges for laying of U.G cables up to 50sqmm in existing pipe as directed by the departmental official including cost and conveyance of all materials and labour charges etc., complete.

Supply and Run of No.8 SWG copper wire including cost of all accessories and labour charges etc., complete. (0.104Kgs/1Mtr)

Supply and erection of Panel mounting 250A, 3 Pole, 35 / 36kA, MCCB with thermal magnetic setting / Microprocessor based release arrangement with all connections etc., complete on existing panel.

Supply and erection of Panel mounting 400A, 3 Pole, 35 /36kA, MCCB with thermal magnetic setting / Microprocessor based release arrangement with all connections etc., complete on existing panel.

Supply and erection of Panel mounting cubical type 630A TPN 415V, 50 Hz. switch disconnector fuse unit complete with front drive mechanism with door inter lock, padlocking arrangement etc., complete with fuse links on existing control panel.

Supply and fixing of electrolytic grade copper bus bar by means of SMC / DMC type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves

Supply and erection of Panel mounting 100A, 3 Pole, 16kA, MCCB with thermal magnetic setting release arrangement with all connections etc., complete on existing panel.

Supply and erection of Panel mounting 125A, 3 Pole, 25kA, MCCB with thermal magnetic setting release arrangement with all connections etc., complete on existing panel.

Supply and erection of Panel mounting cubical type 250A TPN 415V, 50 Hz. switch disconnector fuse unit complete with front drive mechanism with door inter lock, padlocking arrangement etc., complete with HRC fuse links on existing control panel.

Providing independent earthing by exacavating a pit to a depth of 2.25Mtr in all soils as per size specified in the data for Important equipment with 2.5Mtr length 40mm dia C.I pipe and 18" dia 3" thick hume pipe ring with R.C.C. Slab cover duly providing staggered holes filling with 20Kg Salt and 40Kg Charcoal or 40Kg bentonite powder from the bottom of the pipe giving earth connection from electrode through G.I strip of 25 x 6mm x 200mm length to be bolted with nut bolts including supply and termination of No.8 G.I.wire from bottm of the pipe with all accessories and labour charges complete, as per IS specifications 732/1982 (Part II)

Supply and transportation of 95 SqmmX 3.5 core XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I)./1554-I Makes: Torent / Universal / Unicab / Havells / KEI / Gloster / Polycab /RR Kabel

Supply and Fixing of CT operated direct reading type digital type Ammeter of rating below 500A on existing panel , making connection by PVC insulated copper conductor with PVC sleeves / channel etc. as required. Makes : L&T