Design and Development of Sai Mandir Junction and Kuthal Gate including one year maintenance (Further extendable upto 3years)

Amount

Sai Mandir Junction

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying cement concrete - all works upto plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.:

Foundations, footings, bases of columns, etc. for mass concrete

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

providing and laying Ceramic glazed floor tiles of size 300x300 mmthickness to be specified by the manufacturer) of 1st quality conformin J IS : 15622 of approved make in colours such as White, Ivory, Grey ume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : L coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : White sand stone - Exposed face machine cut and table rubbed with rough backing 50 mm thick

Treating and painting a 3D wall mural of 50 mm thickness, positioned under the cultural frame, using water-repellent colors. The work shall include applying a primer and a laminated coating over the mural to ensure durability, protection, and a high-quality, long-lasting finish.

STAINLESS STEEL MASHAL

STAINLESS STEEL MASHAL STAND

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with grader in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.(Plant MIx Method)

Granular Sub-base with Well Graded Material (Table 400.1) By Mix in Place Method Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.

Providing and applying primer coat with SS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means.

Tack Coat on Bituminous surfaces Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

Dense Graded Bituminous Macadam Grading II Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects.

Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35.The finished surface to be level, uniform and free from streaks and holes.

Providing and fixing of retro reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of Type XI retro reflective sheeting fixed over 3mm/4mm thick Aluminium composite material sheet vide clause 801.3, depending on the size of the sign fixed over back support frame of min 25 x 25 x 3mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67 (i) 900 mm equilateral triangle

(ii) 600 mm equilateral triangle

(iii) 600 mm Circular

(iv) 800 x 600 mm Rectangle

(v) 600 x 450 mm Rectangle

(vi) 600 x 600 mm Square

(vii) 900mm high Octagon

Maintenance of shoulder work such wall cladding Art work etc as per dir. ER in charge.

Kuthal Gate

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying cement concrete - all works upto plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.:

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : second class teak wood for bus stand

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as pecified and as directed by the Engineer-in-Charge. Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent.

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : White sand stone - Exposed face machine cut and table rubbed with rough backing 50 mm thick

Providing and Placing 15mm thick pine wood cladding on the top frmae of the gajibo all the sides

Treating and painting a 3D wall mural of 50 mm thickness, positioned under the cultural frame, using water-repellent colors. The work shall include applying a primer and a laminated coating over the mural to ensure durability, protection, and a high-quality, long-lasting finish.

Providing and fixing Pine shingles of size 36 inches in width, 12 inches in length, and a minimum thickness of 12 mm. The shingles shall be securely anchored, bolted, pasted, and fixed on the roof with precision to ensure durability, stability, and an aesthetically pleasing finish, adhering to all relevant standards and best practices.

Providing and placing 25 mm thick Bison board on the truss below the shingles, securely fixed with bolting and anchoring to the square hollow pipe framework. The work shall ensure proper alignment, stability, and durability, adhering to standard specifications and best practices

Providing and fixing 12 mm thick Pine wood false ceiling, complete with necessary framing, hosting, and anchoring. The ceiling shall be securely installed, ensuring proper alignment, stability, and a high-quality finish, in compliance with standard specifications and best practices

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Steel work in built up tubular (round, square or rectangular hollow tubes etc.)trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.1 Hot finished welded type tubes.

12 MM HILTI ANCHR BOLT 150 MM LONG

Random Rubble Stone Masonry laid in 1:6 cement and sand mortar, in breast walls, retaining walls, parapets, scuppers, etc. including supply of all material, labour, T&P and royaltiies etc. complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203 of MORD Specifiction

Hand Packed stone filling in back of wallls including cost of all materials,royality, T&P etc. complete as per direction of Engineer-in- charge. (As per PWD Uttarakhand specifications)

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with grader in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.(Plant MIx Method)

Granular Sub-base with Well Graded Material (Table 400.1) By Mix in Place Method Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.

Providing and applying primer coat with SS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means.

Tack Coat on Bituminous surfaces Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

Dense Graded Bituminous Macadam Grading II Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects.

Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35.The finished surface to be level, uniform and free from streaks and holes.

Cement plum Masonry with 40% plum & 60% 1:3:6 cement concrete including supply of all material, labour, T&P etc. required for proper completion of the work. as per drawings and technical specifications Clause 802, 803, 1202 & 1203 of MORD Specifiction

Providing and fixing of retro reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of Type XI retro reflective sheeting fixed over 3mm/4mm thick Aluminium composite material sheet vide clause 801.3, depending on the size of the sign fixed over back support frame of min 25 x 25 x 3mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67 (i) 900 mm equilateral triangle

(ii) 600 mm equilateral triangle

(iii) 600 mm Circular

(iv) 800 x 600 mm Rectangle

(v) 600 x 450 mm Rectangle

(vi) 600 x 600 mm Square

(vii) 900mm high Octagon

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

Fabrication, supply and errection of mannequins, models and scupture made up of materials such as steel, plastic etc. The mannequins, models and sculpture shall match with the asthetic surrounding values / views of following Height (b) Sculpture of Height above 7' upto 10'

Electrical work

SITC of high quality long through multi color wash light, Protection Rating : IP66, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" and having CE certification against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights having the rotation degrees embosed in the die cast. Power consumption : 50W, CCT : RGBW(6000-7000K), (as per the design approval), Optics : PMMA with holder, Beam Angle : 25º/45º/60º, Control : DmX512 Channel : 4 CH, Body : Die casted / extruded aluminium with embossed manufacturer logo, Seperate compartment for keeping the decoder/driver in the housing which can be easily removable for service without disturbing the LEDs/Optics, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : Constant DC 24V with external driver to the constant current decoder, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK08, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK07, IP66, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power & DMX Loop In/Out along with IP67 connector having the length >300mm. ( Make- Leksa/Homdec/Lighting Technologies/NERI)

SITC of 12W multi color spot light, Protection Rating : IP66, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" and having CE certification against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable wall mount yoke arrangements for fixing the lights. Power consumption : 12W, CCT : RGBW, (as per the design approval) Optics : PMMA with holder, Beam Angle : 25º/45º/60º, Control : DmX512 Channel : 4 CH, Body : Die casted / extruded aluminium with embossed manufacturer logo, Seperate compartment for keeping the decoder/driver in the housing, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : DC 24V with external driver, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK05, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C , LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK05, IP66, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power & DMX Loop In/Out along with IP67 connector having the length >400mm. ( Make- Leksa/Homdec/Lighting Technologies/NERI)

SITC of 20 W multi color spot light, Protection Rating : IP66, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" and having CE certification against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable wall mount yoke arrangements for fixing the lights. Power consumption : 12W, CCT : RGBW, (as per the design approval) Optics : PMMA with holder, Beam Angle : 25º/45º/60º, Control : DmX512 Channel : 4 CH, Body : Die casted / extruded aluminium with embossed manufacturer logo, Seperate compartment for keeping the decoder/driver in the housing, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : DC 24V with external driver, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK05, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C , LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK05, IP66, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power & DMX Loop In/Out along with IP67 connector having the length >400mm. ( Make- Leksa/Homdec/Lighting Technologies/NERI)

SITC of high quality Multi Color Neon Flexible light, Protection Rating : IP65, Mounting Structure : Adjustable wall mount SS clips for fixing the lights. Power consumption : 12W, CCT : RGB/RGBW, (as per the design approval) Beam Angle : 120º, Control : DmX512 Channel : 4 CH, Power Input : DC 24V with external driver, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Fixture will be suitable to operate in a temperature range of 0°C to 50°C , LED life time should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. LED Makes should be CREE, LumilLED, Osram, Seoul, Epistar, Nichia or equivalent with the engineer or 3rd party testing laboratory approval.

SITC of high quality long through multi color wash light, Protection Rating : IP66, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" and having CE certification against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights having the rotation degrees embosed in the die cast. Power consumption : 50W, CCT : RGBW(6000-7000K), (as per the design approval), Optics : PMMA with holder, Beam Angle : 25º/45º/60º, Control : DmX512 Channel : 4 CH, Body : Die casted / extruded aluminium with embossed manufacturer logo, Seperate compartment for keeping the decoder/driver in the housing which can be easily removable for service without disturbing the LEDs/Optics, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : Constant DC 24V with external driver to the constant current decoder, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK08, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK07, IP66, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power & DMX Loop In/Out along with IP67 connector having the length >300mm. ( Make- Leksa/Homdec/Lighting Technologies/NERI)

SITC of 12W multi color spot light, Protection Rating : IP66, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" and having CE certification against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable wall mount yoke arrangements for fixing the lights. Power consumption : 12W, CCT : RGBW, (as per the design approval) Optics : PMMA with holder, Beam Angle : 25º/45º/60º, Control : DmX512 Channel : 4 CH, Body : Die casted / extruded aluminium with embossed manufacturer logo, Seperate compartment for keeping the decoder/driver in the housing, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : DC 24V with external driver, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK05, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C , LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK05, IP66, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power & DMX Loop In/Out along with IP67 connector having the length >400mm. ( Make- Leksa/Homdec/Lighting Technologies/NERI)

SITC of high quality DMX decoder, Power Input : DC 24V, Protection rating : IP65.

SITC of PVC insulated multi core electrical un armoured flexible 5C x 0.5Sq mm power cable having less electrical losses.

SITC of PVC insulated multi core electrical un armoured flexible 3C x 1.5Sq mm power cable having less electrical losses. This PVC insulated and round sheathed wire features a bright multi strands copper conductors and it supports voltage grade up to 1100V.

SITC of PVC insulated multi core electrical un armoured flexible 3C x 2.5Sq mm power cable having less electrical losses. This PVC insulated and round sheathed wire features a bright multi strands copper conductors and it supports voltage grade up to 1100V.

SITC of 5 core DMX cable comprises twisted pairs with shield support for carrying of data. DMX512 cable is used for connecting all light consoles that use DMX 512 standard data transmission.

SITC of IP65 "I" power connectors having 3/4 pole cable connector, chuck type strain relief, Current rating 20 A rms continuous, Easy and extremely precise locking system "Quick Lock" High impact materials - long-lasting and reliable

SITC of IP65 "I" DMX connectors having 3/5 pole cable connector, Male/Female connector with improved latch, cage type contacts, "solder stop" for easy soldering, and additional ground contact for best contact integrity between chassis and cable connector. More durable housing for maximum reliability.

SITC of 5 pin XLR Male connectors having 5 pole cable connector, Male/Female connector with improved latch, cage type contacts, "solder stop" for easy soldering, and additional ground contact for best contact integrity between chassis and cable connector. More durable housing for maximum reliability.

SITC of 5 pin XLR Female connectors having 5 pole cable connector, Male/Female connector with improved latch, cage type contacts, "solder stop" for easy soldering, and additional ground contact for best contact integrity between chassis and cable connector. More durable housing for maximum reliability.

SITC of Power Distribution Board made up of MS Sheet metal fabricated housing black powder coated and ivery connectors for the internal terminations and external outgoing connecting points, fibre / brass glands of suitable size fitted MCB control for outgoing circuits. - 9 Nos of 6/10A SP Outgoing MCB's. - 1No of 16A TPN Incoming MCB.

SITC of IP driver box made up of PVC / UPVC and ivory connectors for the internal terminations and external outgoing connecting points, fiber / brass glands of suitable size fitted MCB control for outgoing circuits.

SITC of DMX isolator or splitter provides Isolated optical DMX splitter provides 8 outputs from a 1 input and Input voltage: AC 110 to 220 V, 50 Hz, Product features: Group 1 & group 8 DMX signal change.

SITC of Din Rail Mount DMX controller can be used to control a wide variety of different DMX systems- from RGB/RGBW to more advanced moving and color mixing luminaires, 512 DmX channels in live mode (computer), stand alone mode with 1 area and 20 scenes, Mac OSx 10.6/10.7/10.8 - Windows XP/VISTA/SEVEN/8 32/64 bits and USB 2.0, XLR3, mini USB, Power From 5V to 5.5V DC (AC/DC adapter in option.

SITC of Programming charges

SITC of additional accessories for installing the lights as per the final drawing/site condition consisting of clamps, brackets, angles, conduits, joints, hardware's like fasteners, nut & bolts etc.,

NARAYAN SINGH (BID ID -362700)