Constt. Of Block Veterinary Hospital at TSG Block Trespone) Under DP

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30cm in depth, 1.5mtr in width as well as 10sqm on plan) including disposal of excavated earth lead up to 50mtr and lift up to 1.50mtr disposed earth to be leveled and neatly dressed in:

All kind of soil. @20%

Ordinary rock @40%

Hard ROCK (B.P).@40%

Earth work in excavation by mechanical means in trenches for foundations, drains, pipes, cables etc. (Not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like Not exceeding 10 Sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: within alead of 50 metres:

All kinds of soil @40%

Ordinary rock @40%

Hard rock (requiring blasting) @20%

Disposal of Mulba/Excavated Earth Beyond 50m By 05 Km Mechanical Transport including loading, unloading and stacking)

Filling available excavated earth (excluding rock) in trenches,plinth, sides of foundations etc. in layers Not exceeding 20 cm in depth, consolidating each deposited layer by ramming andwatering, lead upto 50 m and lift upto 1.5 m

Dumping stone filling Excluding cost of stone in horizontal on level

Dry stone pitching Excld. Cost of stone in horizontal on level.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to plinth level. 1:4:8 (1 cement: 4 coarse sand: 8 graded stone aggregate 40mm Nominal) crushed.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to plinth level. 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 40mm Nominal) crushed.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished 40 mm thick with 20 mm nominal size stone aggregate

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string coursed, filets, columns, pillars, piers, abutments, posts and struts, etc, up to floor five level excluding cost of centering, shuttering, finishing and reinforcement.1:1.5:3(1 cement:1.5 coarse sand:3 graded crushed stone aggregate 20mm nominal size)

Reinforced cement concrete work in beams suspended floors , roofs having slope upto 15 degree, landings balconies, shelves,chajjas, lintels, bands, plain window sills, staircase and spiralstair cases upto floor five level excluding the cost of centering shuttering, finishing and rienforcement with in 1:1.5:3 (1cement : 1.5 coarse sand: 3 graded crushed stone aggregate 20mm Nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level

Centering and shuttering including strutting, propping etc. and removal of form for :-

Foundations, footings, bases of columns etc. for mass concrete.

Columns, pillars, piers, abutments, posts and struts.

Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Suspended floors, roofs, landings, balconies and access platforms.

Stairs (excluding landings) except spiral staircases

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position with cement motor 1:3(cement: 3 course sand) cost of required centering shuttering and finishing smooth with 6mm thick cement plaster 1:3(1cement:3 fine sand) on exposed surface complete 1:3:6(1cement:3 coarse sand :6 graded stone agg, 20mm nominal size

Providing wood work in frames of doors windows and clerestory windows and other frames wrought framed and fixed in position 2nd class kail wood

P/F paneled or paneled and shutters for doors windows and clerestory windows including ISI marked black enameled M.S butt Hinges with necessary screws exclude which will be paid for separately 1st class kail wood for 35mm thick

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :. 2nd class kail wood

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 9.27.1 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size2nd clss kail wood

Supplying and fixing in position glass pane 4mm thick incld. Cost of wooden beading complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting hoisting ,fixing in position all carriage complete.

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, omplete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating Not less than 275 gram/m2

Providing valleys of 90 cm wide overall in plain G.S. sheet fixed with polymer coated Jor L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete : 12.5.1 1.60 mm thick with zinc coating not less than 350 gm/m2

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimetre channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimetre of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimetre channel with the he p of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimetre channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge, complete with; 32.6.1 2nd class kail wood

Supplying and fxing of Almirah 24" Deep Made of Budloo plank/ black board having paneled / flush shutters with teak wood facing / smoke teak ply inclsuing all fixing of handle and other accesoes etc complete.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc.Budloo/Fir wood

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183. Density 17 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene bags placed over existing false ceiling and held in position by crisscrossing GI wire.

Providing and fixing of T&G wooden panelling of rait wood/ Shalimar brand including fixing wooden Cornice , iron screws complete.

Applying French spirit polishing : 13.68.1 Two or more coats on new works including a coat of wood filler

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : 9.47.2 25 mm dia (heavy type)

Providing and fixing wooden curtain box of 8" width incld. Fixing of teak wood Polishing and fixing of rods complete.

20mm Cement plaster on internal wall of mix: 1 : 6 (1 cement : 6 fine sand).

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complet

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with textured exterior paint of required shade :13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Applying priming coat: 13.50.1 With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 13.62.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth

Providing and fixing Door windows Accessories of Approved Barand and manufacture incld. All fixture complete.

L-Drop with Center Lock System

L-Drop for doors

Tower bolt 8" long for doors

Tower bolt 6" long for Windows

Eye Bolt for Windows

Handle for Door

handle for windows

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.)

Providing and fixing double glazed hermetically sealed glazing in aluminum windows, ventilators and partition etc. with 6mm thick clear float glass both side having 12mm air gap including providing EPDM gasket, perforated aluminum spacers, desiccants, silicon sealant (both primary and secondary sealant) etc. as per specifications, drawings and directions of Engineer-in-charge complete.

Flooring with marble stone of specified thickness as per sample of marble approved by Engineer-in-charge, over 20 mm(average) thick base of cement mortar 1:4 (1 cement:4 coarse sand) laid and jointed with grey cement slurry including rubbing, polishing and curing complete with 16mm Makrana White Second quality

Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) :

Kota stone slab 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average) thick cement mortar 1:3 (1 cement:3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing, polishing and curing complete.

Supply and installalation of Laminate Flooring high density fiberboard (HDF) 820KG/M3 Density Smooth Matt Finish 12MM THICK Single Click with U Groove having Abrassion Class AC4 manufactured by Embossed in Register (EIR) process including underflooring foam 4mm thick , skirting , reducer , T-Profile and Beeding All Complete job (Leben, Robina or any other approved brand as per specification approved by engineer In charge )

Providing and laying gang saw cut of specified thickness, mirror polished pre- moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in Charge. 16.90.1 18 mm thick

Providing and laying vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thickcement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing water closet squatting pan (Indian typeW.C. pan )with 100mm sand cast Iron P or S trap,10 litre low level white P.V.C. flushing cisternzwith manually controlled device (handlelever) conforming to IS:7231,with all fittings and fixtures complete including cutting and making good the wall sand floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.LSOR 17.1.1

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.JAGUAR/CERA Make

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing Stainless Steel AISI 304 (18/8) Double blow kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required:47x20x9 Inches of approved Brand and manufacture (Hindware/Jaguar/Imperio/Kaff of any approved Brand as per Engineer Incharage)

Providing and fxing of white vitreous china laboratory sink including making all connection excluding cost of fitting.

Providing and fixing mirror of superior glass( of approved quality) and of required shape and size with plastic . moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 1500x450 mm.

Providing and fxing of PTMT liquid soap container 109mm wide, 125mm height and 112mm distance from wall of standard shape with bracket of the same materails with snap fittingof appoved quality.

Providing and fixing P.V.C. pipe and pipe fittings of the following Nominal dia to P.V.C. Soil/Waste/Ventilating pipesof approved brand ,,

PVC Pipe 100mm

PVC Pipe 75 mm

PVC TEE 75

PVC TEE 100

collar 75mm

collar 110 mm

Bend 75mm

Bend ° 110 mm

PVC socket 75mm

PVC socket 110 mm

PVC Trap 75mm

PVC Trap 110 mm

PVC door Junction 100mm dia

PVC door Junction 75mm dia

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.incld. Tee, Elbow , Union , Socket etc

PN-16 pipe, 25mm OD (SDR-7.4)

PN-16 pipe, 32mm OD (LSOR18.1.2)

Providing and fixing Ball value (Brass) of approved quality High and Low Pressure complete.

15mm,20mm , 25mm &32mm Nominal Bore

Supply and installation of High Quality self regulating heat tracer for Specialized Heating Solutions for Winterisation of water pipeline including all accessories complete including Supply and installation of Circuit Control Panel with RCBO MCB ,THERMOSTAT (0-120) DEG C, power connector-two way-6 sq.mm, w.p. splice connector,w.p. tee connector,end seal,mounting kit-w.p. jb,g.i. pipe strap 4",al. adhesive tape roll ( 50 mm w x 20 m l),f.g. adhesive tape roll (DANFOSS Make OR CHROMALOX any other approved brand as per the direction of Engineer-In-Charge)

Supplying and fixing High Quality 32mm Thick Nitrile Insulation Tube for water pipeline of approved brand 2 Inch Size (Armaflex Class-o Armacell) , rockwool of apparent density 128 Kg/m3 on outer side of nitrile tube of 50mm thickness including alumunium duct clading (Alumunium Sheet Guage Thickness = 0.46MM TO 0.71MM )of approved quality and finish as per the direction of engineer in charge (Nitrile Tube 32mm > Rock Wool 50mm > Alumunium Duct Clading 0.46mm to 0.71mm)

Supply and installation of electrical Underfloor heating mats for floor heating systems non-corrosive, flexible heating elements including cables, pre formed cable mats including smart thermostat and digital electrical control panel all complete (STIEBEL ELTRON / DANFOSS Or any other approved brand

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour:600 mm long towel rail with total length of 645 mm, 78 mm wide and effective height of 88 mm, weighing not less than 190 gms.

Providing & fixing C.P. toilet paper holder, with roller complete, including cutting and making good the walls wherever required.

Providing and fixing health faucet with concealed fitting arrangement of approved quality and make.

Providing & Fixing wall mixer mixer single lever telephonic wall mixer of quality and make approved brand and manufacture.

Providing and fixing water heater (GYSER) 50 ltr of standard quality and make including all fixtures.

Providing and fixing water heater (GYSER)15 ltr of standard quality and make including all fixtures.

Providing and fixing of bip cock of standard quality and approved make

Providing and fixing angle valve of standard quality and make including all accessories complete job

Providing and installation of PUF (Puf Insulated Tanks) water tank capacity 1000 ltrs of approved brand (SYNTEX OR ANY OTHER APPROVED BRAND) as per direction engineer incharge

Providing nd fxing of 25mm dia 2mm thick ISI marked PVC conduit pipe for carrying electrical wiring in the slab with light box and fan box complete.

Providing and fixing 1.5HP water Pump incld. All fitting complete.

Supply and installation of Concealed Mixer and Divertor For Bath and Shower System (Mixer and Diverter including Single-control Recessed Bath And Shower Valve) including bath spout and Square Shape Single Flow Overhead Shower 150 MM X 150MM of approved/Premium quality and make direction of engineer incharge (JAGUAR/CERA/KOHLER or Equivalent) as per the site Engineer Incharage

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

carraige of sand /bajri for an average lead of 12 KM by MT .

carraige of cement /steel for an average lead of 20KM by MT .

Please Enable Macros to View BoQ information