REPAIR TO CHAJJA, COLUMNS, BEAMS AND FACIAS TO MD AND OTM ACCN AT N AREA AND HALLOMAJRA UNDER GE CHANDIGARH

Amount

Demolition of reinforced concrete of roofs, floors(other than ground floors ) beams, staircases, landing chajjas and similar suspended work (upto 2nd floor and mumty) complete all as specfied and directed.

Demolition of cement concrete (un-reinforced upto 2nd floor and mumty), chajja ,and paving n.exc 15cm thickness complete all as specified and as directed

M&L for reinforcement cement concrete B-1, 1:2:4 (20 mm graded aggregate) nominal mix for Slabs supported on walls,beams and lintle in floors,roofs, landings, balconies,canopies, deck slabs and the like,( upto 2nd floor) complete all as specified and directed.

M&L for cement concrete type B-1, 1:2:4 (10.5 mm graded aggregate) Nominal mix for chajjas supported on walls,beams ,(Upto 2nd Floor) complete all as specified and directed.

M&L for reinforcement cement concrete B-1, 1:2:4 (20 mm graded aggregate) for stair case ,including steps thread and raiser, ( upto 2nd floor ) complete,all as specified and directed.

M&L for use and waste of Formwork to soffits of suspended slabs on flat ,such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat height (upto 2nd floor) complete all as specified and directed.

M&L for use and waste of Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide height (upto 2nd floor) complete all as specified and directed.

M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to TMT bars complete all as specified and directed.

All as per item No.8 but 6mm to 8mm dia complete all as specified and directed.

M&L for installation of rebar by using hilti hammer drill with carbide drill bit, Chomical dispensing gun for inserting RE-500V3 Chemical upto minimum depth of (10X dia of bar) as in chajah, beam, lintel, columns slab and parapet at any height Before inserting an an anchor/bar, hole must be free from dust debris, water ice and oil grease etc by using Dia of bar 10/12mm complete all as per manufacture instructions. Note:- (i) Reinforcement will be measured and paid separtely. (ii) Rates are inclusive of from work shuttering and safely measures.

M&L for providing PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in roof kerb or mud stops rounded or chamfered on edges all as specified and directed.

Taking down cement plaster including racking out joints hacking for key scrubbing down with water all as specified.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick work or concrete surface finished even and smooth with out using extra cement upto 10 mtr height complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces with WPC upto 10 mtr height complete all as specified and directed. Note: Water proofing compound will be paid seprately.

M&L for rendering 10 mm thick in cement mortar 1:3 on fair faces of concrete surfaces as in ceiling finished even and smooth upto 10 mtr height complete all as specified and directed.

Supply only water proofing compound, complete all as specified.

M&L for preparation of newly plastered surfaces and two coats cement base paint over and including a coat of primer on walls surface complete all as specified.

M&L for preparation of newly plastered surfaces and two coats of oil bound distemper over and including a coat of primer on walls surface complete all as specified annd directed..

M&L for three coats of white wash on ceiling surface including preparation of newly plastered surfaces complete all as specified annd directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified.

Brick work with sub class 'B' bricks, class Designation 10 straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and as directed..

Brick work with sub class 'B' bricks, class Designation 10 straight or curved on plan exc 6m mean radius built in cement mortar 1:6 EXCEPT BRICKS complete all as specified and as directed.

M&L for 50 mm thick guniting in patches on to the required area on RCC/PCC columns, beams, stairs, lintels, retaining walls, sunshades, roofing slab including under chicken wire mesh etc. of all sizes and shapes at all heights from existing ground floor and all locations with cement and mortar 1:2 (1 cement : 2 sand) under 2 to 2.8 Kg/Cm2 pressure after removing the damaged loose spalt concrete portions by chipping, removal of dust and applying one coat of rust convertor/kp-100 equivalent grade over reinforcement wherever necessary providing and tying in position 25mm x 25mm x12 gauge dia wire MS welded mesh or smaller size over treated surface ready to receive grouts, curing for 10 days etc,loose spalt concrete portions by chipping, removal of dust over treated surface ready to receive grouts including 5mm to 10mm thick plastering in CM 1:4 to match existing surfaces and finished even and smooth including curing for 10 days etc, complete operation all as directed , including two coat of cement base paint over a coat of primer ,including labour charges hire for all tools and plant machineries cost of consumables, scaffolding all types of protective equipments, plant floors, pipelines, vessels, materials etc. so as to do guniting in plant, removing the debris out of MOD land in low lying areas and leveling as directed,height (Upto 2nd Floorcomplete all as specified and directed by Engr-in-charge.

All as per item No 23 above but 30 mm thick.

Cutting grooves in brick wall, 75 mm wide and 65 mm deep for inserting membrane and shaping horizontal face of groove with cement mortar 1:3, complete all as specified and directed.

M&L for repairing the edges of concrete chajjas, facias, columns & the like by providing PCC (1:2:4) type B-0 including all necessary form work and/ or provision of rendering 15mm thick (average thickness) in cement mortar (1:3) with chiken wire mesh, after applying a coat of cement slurry @ 3kg/sqm of surface finished even and fair, surface area not exceeding 1.00 Mtr wide, in patches including two coat of cement base paint over a coat of primer including taking down swoolen/damaged plaster or concrete complete all as specified and as directed.

M&L for complete removal of existing treatment including preparation of old plaster surface on wall and applying two coat of cement base paint complete all as specified and as directed.

S&F for plain Sheet glass 4 mm thick, ordinary quality and glazing with oil pane putty in squares not exceeding 0.5 Sq. mm in each pane complete all as specified.

S&F for figured glass, 4 mm thick, pin head type and glazing with oil putty in squares not exceeding 0.5 sq. m in each pane, complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new onescomplete all as specified and directed by Engr-In-Charge.

M&L for one coat of synthetic enamel paint on old steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces

M&L for one coat of synthetic enamel paint over old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces complete all as specified.

M/s REEDIT CONSTRUCTION (BID ID -3094792)

JK ENGINEERS (BID ID -3104732)