MLA FUND, SRI MATHEW T THOMAS, MLA FABRICATION, PAINTING AND ERECTION OF NEW SHUTTERS 2 NOS AT KARUTHALILPADI NEAR KUTTOOR JN, THIRUVALLA MECHANICAL WORKS. Re-Tender

Amount

Supply ,fabrication & erection of Secondary Embedded parts and Concreting

15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.106 : Supply of MS flats including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

Repairs to embedded parts

od39615/2019_2020/MH : Fabrication and errection of Embedded parts for canal shutters ( Up to 2 tonne weight ) and accessories asper approved specifications, drawings and directions of deptl fficer at site including cost of labour,machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of materialalready supplied

od68046/2019_2020/MH : Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track,Seal seat etc as per approved specifications, drawings and directions of deptl officer at site including cost of all materials,labour,machinery for planing, welding,shearing, grinding etc,lead and lift, conveyance, incidental and handling etc complete

Repairs to Shutter

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

od68047/2019_2020/MH : Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight ) /Hoisting Bridge /Platfurm and accessories etc. for the same as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od39770/2019_2020/MH : Supply of SS Bolts a nd Nuts

Repairs to shutter rollers and rubber seals

od66628/2019_2020/MH : Supplying and fixing cast steel thrust roller assembly having 200mm Dia, 80mm tread width, SS(304) shaft and 22312E self aligning spherical roller bearing and accessories as per approved specifications and drawings including cost of all materials, machineries, labour , all lift and lead, incidental and conveyance charges etc complete

od39610/2019_2020/MH : Supplying and fixing in correct position with specified initial interface the flat typerubber seal confirming to IS 11855 to the canal gates including cost of MS bolts and nuts, all labour andmachinery and incidental and conveyance chargers complete as per approved specification and drawing.

od39614/2019_2020/MH : Supplying and fixing in correct position with specified initial interface L-type/Bulbnose rubber seal confirming to IS 11855 to the canal shutters including cost of MS bolts and nuts ,all labour,machinery,incidental and conveyance chargers complete as per approved specification and drawing

od11904/2020_2021/MH : Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Bridge / Platformincluding hand rails , lader etc. for the same including . alignment correcting and settingcomplete including cost of all labour, machinery, incidental and conveyance , lead and liftcharges etc complete but excluding cost of materials already supplied

Repairs to Hoisting mechanism

od68124/2019_2020/MH : Supply and fixing of Chain & Sprocket 180pcd/120pcd 3/4" for Manual operation of worm & pinion mechanism including cost of materials and labour etc.complete.

od68125/2019_2020/MH : Supply and fixing of Line shaft, Muff coupling and Plummer block bearing for connecting the two worm and pinion mechanism including all material, labour etc. complete.

od68126/2019_2020/MH : Providing of worm and pinion having a lifting speed of around 3.2 cm/min for 24 rpm at hand operation drive shaft side including cost of all materials, labour, hire charges and conveyance.

od68127/2019_2020/MH : Providing EN-8 screw rod with one number of EN -8 scerw shaft, hand operation including cost of all materials, labour, hire charges and conveyance.

Repairs to Hoisting platform , Erection and trial run of gate

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.103 : Supply of MS checquered plates including cost of conveyance charges

od66637/2019_2020/MH : Supply of G.I pipes 50 mm dia

od66638/2019_2020/MH : Supply of G.I pipes 32 mm dia

od68047/2019_2020/MH : Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight ) /Hoisting Bridge /Platfurm and accessories etc. for the same as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

85.115 : Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od39773/2019_2020/MH : Bolts and nuts

od39774/2019_2020/MH : Supply of Bolts and nuts above 300 mm in length

od68054/2019_2020/MH : Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Bridge / Platform including hand rails , lader etc. safely in the grooves , assembling and aligning including cost of all machinery, labour all incidental and conveyance charges etc complete as per direction of departmental officer at site

od44448/2019_2020/MH : Trial run the gates with its hoisting mechanism etc. including cost of all materials, machinery , labour, all lift and lead, incidental and conveyance charges etc. As per instruction of departmental officers in charge.

SAI ENGINEERING

ASHIFUL HAK.C

SILK-Steel Fabrication Unit

Bidder Name

ASHIFUL HAK.C

GANGADETHAN

SILK-Steel Fabrication Unit

SAI ENGINEERING