Special Repairs to bldg No T-38, T-33, T-35, T-36 and T-43 (Hutted Accn) of 420 Single OR Accn OTM line of 126 Lt AD Regt (Comp) and bldg No T-50, T-51, T-55, T-56 and T-57 (OTM) of 940 Lt AD Regt (Comp) Wksp in Shikargarh at Army Area Jodhpur

Amount

Demolition of cement concrete of any description and in any position not otherwise specifically provided for (such as copings, bands of any type, roof padding, kerbs etc overall thickness and removing the dust debris etc to a distance not exc 250 meter from site and disposing the same complete all as specified and as directed by Engineer in charge.

M&L for Cement concrete 1:2:4 type B-0, (using 12.5mm graded crushed stone aggregate) as in mass concrete etc., to make up undulations as in levelling course over roof with rough finished surfaces complete all as specified and as directed.

M& L for roof treatment in the following stages :- (a) first Course : M&L for 10 mm thick plaster with CM 1:3 mixed with water proofing compound as per manufacturee instructions (Note: - WPC shall be measured and paid separately) (b) Second Course : One coat of bitumen primer T-10/polymerised confirming to IS 3384 @ 0.30 ltr/Sqm (c) Third Course : One coat of Bininding material using blown type bitumen conforming to IS 702 grade 85/25 @ 1.20 Kg/Sqm (d) Fourth Course : A layer of APP membrane polymeric membrane centre core of 100 micron HMHDPE outer film 20 micron each, thickness 2 mm having weigh 3.00Kg/Sqm (e) Fifth Course : A coat of bonding materail using blown type bitumn conforming to IS-702 of grade 85/25 @ 1.20 Kg/Sqm (f) Sixth Course :40mm thick PCC 1:2:4 padding, well compacted using 20 mm graded aggregate with grooves shall not be exceeding 0.40 Sqm.

Supply only Integral water proofing Liquid ISI Marked.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed.

Racking out joints/pointing to square rubble masonry Jodhpur type regular coursed built in cement mortar complete all as specified and as directed.

M&L for 15 mm thick rendering / plastering in CM 1:6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished fair and even and smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick rendering/ plastering in CM 1:4 on stone masonary surfaces or other than fair face of stone work or on one side of lathing finished even and smooth complete all as specified and as directed.

M&L for rough cast rendering on wall surface over 10mm thick in CM 1:3 complete all as specified and as directed.

Preparing new plastered surfaces and material & labour for applying two coats of distemper oil emulsion on walls including over a coat of chalk whitening/ suitable primer etc., complete all as specified and as directed.

Preparing new plastered surfaces and material & labour for applying two coats of cement base paint on walls including over a coat of primer etc., complete all as specified and as directed.

Preparation of old decorated plastered/ unplastered surfaces of ceiling and M&L applying one coat of white wash complete all as specified

Preparation of old decorated plastered surfaces of walls, chajjas ,fascias roof projection etc., and M&L applying one coat of cement base paint complete all as specified

Demolition of concrete (unreinforced) in ground floor not exceeding 15cm thickness below or above ground level including floor finishes and removing debris from the site all as specified and as directed.

Dismantling glazed tiles/ kota stone/ terrazzo tiles any type as in dado/ skirting etc; including cement mortar bedding ( but not backing ) complete all as specifide.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in floors/ levelling course to floors/ sub base under floors finished rough and prepared to receive floor finishes complete all as specified and as directed.

M&L for machine cut Kota stone slab as in flooring 18mm (+ 2mm) thick laid over and including 20mm thick screed bed or bedding layer in cement mortar 1:4, set and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, cutting and polishing (mirror type) complete all as specified.

M&L for machine cut Kota stone slab as in skirting,dado of length not less than 500 mm each unit, 18mm (+ 2mm) thick laid over & including 10 mm thick screed bed of rendering in cement mortar (1:4), set and jointed in cement slurry mixed with pigment to match the shade of slab including rubbing, cutting and polishing (mirror type) complete all as specified.

M&L for machine cut pre polished (mirror type) Kota stone slab as in window cills 18mm (+ 2mm) thick laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:4 set and jointed in cement slurry mixed with pigment to match the shade of slab including rubbing, cutting etc; complete all as specified.

Rounding of or moulding to edge (half round) of stone of any description including rubbing and polishing (Granite/ mirror finish) complete all as specified and as directed.

M&L for Jodhpur stone slab patti 40 to 50mm thick set in over and including 15mm thick cm 1:4 and jointed & pointed in neat cement slurry as in floors, plinth protection, steps etc; complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2, (40mm graded stone aggregate) as in sub floor, sub bases, floor and paving etc; complete all as specified.

M&L for 60mm thick factory made pre cast cement concrete rubber moulded laquer finish using chemical and admixure inter locking tiles having compressive strength not less than 350 kg/ Sqcm, of shape and colour as approved by GE , laid over 25mm thick compacted approved sand cushioned surface, joints filled by fine sand and compacting the top surfaces of paver blocks after laid etc of approved make all as specified and as directed.

M&L for factory made precast cement concrete solid blocks M-30 Grade, using 20 mm graded crushed stone aggregate as in kerb stones of any size (with plain or interlocking joints as directed) set in cement mortar 1:4 for path edgings etc; embedded in position including all necessary excavation, tamping ground arround blocks and removal of rubbish/ surplus soil etc., complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in kerbs or benching etc including necessary form work complete all as specified.

M&L for Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete all as specified and as directed.

Taking down chowkats or frames of any description area exc 1.5 Sqm and n.exc. 4.00 Sqm each (without taking off shutter from the frames) including cutting hole to size to receive fresh PCC / block for inserting hold fast and making good the disturbed surface with PCC 1:2:4 or CM 1:3 as required at site after insertion of hold fast complete all as specified and as directed.

Taking down chowkats or frames of any description area n.exc 1.5 Sqm each (without taking off shutter from the frames) including cutting hole to size to receive fresh PCC / block for inserting hold fast and making good the disturbed surface with PCC 1:2:4 or CM 1:3 as required at site after insertion of hold fast complete all as specified and as directed.

Pressed steel framed made out of 1.25mm thick MS sheet, of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed.

M&L cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in filling of steel chowkhats including necessary form work complete all as specified.

S&F 35mm thick factory made flush door shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F 35 mm thick factory made, 2nd class hard wood , glazed and skeleton door shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc , size of members of shutters as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, kiln seasoned and chemically pressure treated and fitted to chowkats complete all as specified and as directed.

S&F for mild steel barrel tower bolts, stove enameled black, with bright bolt, 200 mm long and fixed with steel screws complete all as specified.

S&F for 250mm long mild steel, sliding door bolt, plate/ bolt type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum six bolts and nuts, four on bolt plate and two on staple plate complete all as specified.

S&F for 150 mm size mild steel pressed handle oval type stove enameled black complete all as specified and as directed.

S&F for half round door stoper (6 to 7cm long double rod/ plate) of aluminium alloy bodey and tongue, anodised with rubber nosing including fixed to door with four Nos screws etc; complete all as specified and as directed.

S&F 125mm size single action spring hinge bright finished body of mild steel with steel wire spring heavy duty all as per the samples of Make : YANE/ EVERBRITE or equivalent complete all as specified and as directed.

S&F of Factory made steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skeleton shutter jointed internally with flat iron 40x4mm complete including grill of 8/10mm square bars as directed by Engineer incharge, fixed horizontally @ 10cm c/c, hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing No CEJZ/TD/20 sheet 1/3 to 3/3 complete all as specified and directed. Note: Guard bar/ grill shall be measured and paid separately under respective item of Sch 'A'.

S&F for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks,cooler stand ,support using Angle Iron,MS Flat Iron, tubular section etc and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F Sheet glass ordinary quality 4 mm thick and glazing with oil putty in square n. exc 0.5 sqm in each pane or fixed with wooden beads or fixed with rubber gasket in squares any size of pane complete all as specified & as directed.

S&F for galvanised mild steel steel wire cloth,0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples all as specified and as directed.

Decorative mild steel curtain rods 32mm dia (powder/ PVC coated) including fixing brackets & side cups complete fixed in repairs i.e., including taking down the existing unserviceable curtain rods complete all as specified and directed

Preparing new or previously untreated surfaces of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Preparing new or previously untreated surfaces of steel or iron work of any description and girth over 10cm and applying two coats of synthetic enamel paint complete all as specified and as directed by Engineer incharge.

S&F framed work as in doors chowkats of MS angle iron with gusset plates, rails, braces,cooler stand, chajja framed complete drilled for fixing of door etc; to be prepared for hanging with and including hold fasts and locking arrangements confirming to FE- 290 (Gde-E- 165) complete all as specified and directed by Engineer-in-charge.

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

Taking down 15mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specifide.

Taking down 25mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specifide.

S&F 15mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specifide.

S&F 25mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specifide.

Refixing only 15mm bore steel water tubing any grade with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specifide.

Refixing only 25mm bore steel water tubing any grade with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specifide.

S&F in repair 15mm bore stop valve of PTMT any colour high pressure screwed, for iron pipe complete all as specified.

S&F as in repair for Gun metal gate valve 25mm dia, cast copper alloy screwed down, high pressure with capstain head, screwed both ends for iron pipe for unions complete all as specified and as directed.

S&F 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified.

Supply and fix in repair for PVC connection, 15mm size, with PTMT nuts, of length 450 mm long all as specified and as directed.

Dismantling of water tank of capacity exc 250 but n.exc 500 litre and removing to site complete all as specified and as directed.

S&F for Rotational moulded polyethylene water storage tanks of 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm bore ball valve high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and as directed.

M&L for 100mm thick Cement concrete (1:2:4), type B-1 using 20mm graded stone aggregate as in water tank platform finished surface even & smooth without using extra cement complete all as specified.

Taking down carefully copper/Aluminium point wiring including (light, fan, socket or power complete fittings, such as switches, ceiling roses, pendant holders, Batten holders, shades concial fan regulators, light or poWer sockets etc) removing materials from site all as directed.

Taking down carefully UNSV main switch and DB's including MCBs of any size make, type and capacity all as directed.

M&L for point wiring complete with multistrnaded copper conductor 1.5 sqmm size PVC insulated FRLS unsheathed cable 1100 volt grade, conforming IS 694 & color code , drawn in including PVC casing caping suitable capacity , making food disturbed surface complete, sunk in pressed steel terminal boxes of required size not less than 1.6 mm thick factory made and factory painted with top cover 3 mm thick plastic laminated sheet fixed with brass screw and washer with all accessories including single core solid conductor copper 1.5 sqmm size solid PVC insulated unshethed cable as earth wire to common earth and connected to earth dolly drawn in same conduit complete all as specified.(a) One light/Fan point controlled by one one/way switch

All as per item No 62 but One 3 Pin 5 Amps socket outlet on same board

All as per item No 62 but One 3 Pin 5 Amps socket outlet on independent board.

All as per item No 62 above but using 2.5 Sqmm PVC insulatd, unsheathed cable for one 3 Pin socket outlet 15 Amps on independent board.

Fixing only 22 Watt LED Batten with extruded aluminium housing With in Built LED strip, LED shall be having LM80 complied as per L70 standard leds with 6000-6500k CCT, Maximum power consumption shall be 22 Watt with min, 1800 system lumens, 3 stage CCCV driver with voltage range of 150-270 AC and DC output operating voltage of driver should be complied to SELV norms not exceeding 72 DC only . All as specified & directed by Engr-in-Charge. Note: LED tube light fitting 22W shall be issued under Sch 'B' free for fixing

Fixing only connecting, and commissioning of Wall Light fixture 60 watt LED, IP-66 protected ingle piece Die-cast aluminiur housing and heat sink having heat resistive toughned glass at bottom. individual LED shall be having LM-80 complied as per L70 standard LEDs with 5700-6000K CCT. Optics shall be with proper distribution having lenses of either PMMA of polycarbonate material. Maximum power consumption shall be 60 Watt with min 6000 system lumens. 3 stage CCCV driver with min, 4kv surge protection voltage range of 150-270V AC and DC output operating voltage of driver should be complied to SELV norms not exceeding 72 DC only.and including 40 mm light grade pipe and MS clamp with nut & bolt all as specified as directed by Engir-in-Charge. Note: LED street light 60W complete shall be issued under Sch 'B' free for fixing

Supply and fixing switch piano, flush type ,single pole one way 5/6 Amps 240 Volts. Make : LEGRAND/GM/SSK

S/F switch socket combination 2 in 1, 3 Pin, and 5 Amp flush type universal.Make : LEGRAND/GM/SSK

S&F switch socket combination 2 in 1,5 Pin 5 and 15/16 Amp flush shuttered type ISI mark.

S/F ceiling rose surface bakelite three terminal 65 x 50 mm three terminal 250/230 volts ISI marked

Supply and fixing, Distribution board (concealed flush to wall), , double door typein sheet metal enclosurewhenMCB to be used with 200 A rated copper bus bar confirming to relevant IS TPN 8 way complete all as specified.

S&F MCB SPN 6-32 Amps,240 Volts `C` Curve

S&F MCB SP 6-32 Amps,240 Volts `C` Curve

M&L for replacement of existing U/S Earthing complete with galvanized steel earth plate electrode 60 x 60 cm x 6.0 mm thick bured directly in ground (Earth pit not less than 2.25 Mtr deep below groung level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to incl galvanized iron or steel earth lead wire 4.0 mm dia by means of nut bolts, check nuts and washers and galvanized iron or steel pipe 15 mm dia medium grade for protection of GI wire and connected to main switch board watering pipe shall be 20 mm dia GI medium grade incl Excavation earth work in any type of soil, PCC pit including Kota Stone cover complete.

Excavation in trenches not exceeding 1.5 m wide and not exeeding 1.5 m in depth and getting out in soft/loose soil for removing/laying of cable etc as directed by Engineer-In-Charge.

Returning, filling excavated soil in trenches including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick each all as directed by Engineer-In-Charge.

Removing surplus excavated soil to a distance not exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point.

M & L for sand cushioning to PVC cable with using clean dry and natural river sand gently punning below/around cable all as specified.

Supply and laying 40 to 50 mm thick roughly hammer dressed Jodhpur stone slab cover 25 cm to 30 cm wide and not less than 60 cm long dry laid aboutting each other with gap between adjacenet slabs not exceeding 10 mm for underground cable for protection.

Supply and laying in trenches/fixed on walls/poles of passing through pipe, PVC insulated armoured heavy duty LT U/G electric cable with aluminium conductor 1100 volts grade with suitable cable glands and lugs etc as required of following sizes:-(a) 25 Sqmm x 4 core

Supply and fix GI tubing light grade for protection of cable at wall/trench with fixing accessories as directed of following sizes:-(a) 40 mm dia

Fixing only ceiling fan 1200 mm sweep complete with all accessories including fan blades of white colour & electronic fan regulator, connecting up complete with including three core flexible PVC insulated multi stranded copper conductor of size 1.0 sqmm from ceiling rose/conector to fan (earth wire to connected to fan hook), Note: Ceiling fan 1200mm sweep with regulator shall be issued under Sch 'B' free for fixing

S&F GI Tubes, 'light grade' galvanised, 32 mm dia with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

M/S KAUTILYA GARG

DEV INDUSTRIES

HOODA CONSTRUCTION COMPANY

Pioneer Enterprises

KARNI CONSTRUCTION COMPANY