Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Status |
|---|---|---|
| 1 | Admitted-Fee/PreQual/Technical/Finance C108 BAJAJ STEEL INDUSTRIES LIMITED MIDC INDUSTRIAL AREA HINGNA NAGPUR NAGPUR MAHARASHTRA 440028 | 440028 | Admitted-Fee/PreQual/Technical/Finance |
| 2 | Admitted-Fee/PreQual/Technical/Finance S2 SNR RESIDENCY PLOT NO 138 139 VIJAYPURI COLONY AS RAO NAGAR HYDERABAD 500062 | HYDERABAD | HYDERABAD | TELANGANA | 500062 | Admitted-Fee/PreQual/Technical/Finance |
| 3 | Admitted-Fee/PreQual/Technical/Finance | Admitted-Fee/PreQual/Technical/Finance |
| 4 | Admitted-Fee/PreQual/Technical/Finance | Admitted-Fee/PreQual/Technical/Finance |
Tender Value
₹2.1 Cr
EMD Value
₹4.2 L
Closing Date
22 Jun 2022, 2:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
DCE(CED,PD and EP)
Nuclear Fuel Complex, ECIL PO, Hyderabad - 62
CIVIL, STRUCTURAL and ARCHITECTURAL WORKS FOR ECIL SIDE ENTRY GATE AND HCL SIDE ENTRY GATE AT NFC HYDERABAD
2022_NFC_692378_1
C/1271/2022
Limited
Civil Works
Item Rate
180 days
Hyderabad
Please refer Tender documents.
2 documents required · 2 mandatory
₹1,000
PAO, NFC
₹4.2 L
23 Jun 2022
2 Jun 2022
23 Jun 2022
2 Jun 2022
22 Jun 2022
2 Jun 2022
90 days
Amount
I. EARTH WORK :
Felling down carefully trees of girth (measured at a height of 1.0m above ground level) including necessary excavation, removal / destruction of roots, filling the excavated pockets thus formed with good earth, compacting the same, cutting the trunks and branches of trees into suitable pieces, transporting, stacking and disposing the same at the location as directed by Engineer – in – Charge.
Beyond 30 cm girth upto and including 60 cm girth
Beyond 60 cm girth upto and including 120 cm girth
Above 120 cm girth
Earth work excavation in foundations for buildings, machinery,equipment etc. in all soils other than soft and hard rock upto the depths specified below including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a distance of 50 m etc., complete.
Upto 1.50 m depth from average ground level.
Above 1.50 m to 3.00 m depth from average ground level.
Earthwork excavation in foundations for buildings, machinery,equipment in soft rock upto the depths specified below including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a distance of 50 m etc., complete.
Upto 1.50 m depth from average ground level.
Above 1.50 m to 3.00 m depth from average ground level.
Filling available excavated earth (excluding rock) in plinth , sides of foundation etc., in layers not exceeding 20cm in depth , consolidating each deposited layer by ramming and watering , lead upto 50m and lift upto 1.5m.
Lead charges for the 1st 1 KM/2KM or part thereof for additional lead over the initial lead of 50 m by mechanical transport, including loading, unloading, stacking, the disposable soil, rock etc., Note: Measurement of lead charges will be based on truck measurement with a deduction of voids @20% and 50% for soils and rock or debris respectively
a) For soil for 1KM lead.
b) For rock/debris for 1KM lead
Supplying and filling with murrum around machine foundation to act as dampener etc. including watering, ramming, consolidating and dressing complete as specified and directed
II. CONCRETE (PLAIN AND REINFORCED) :
Plain Cement Concrete 1:3:6 using Portland Pozzolana Cement conforming to IS 1489 Part-1 (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, Andhra Cements Ltd., KCP make) with crushed stone sand and graded stone aggregates of 20mm maximum size at all depths/heights below/above plinth level including consolidation, finishing smooth/broom finish as applicable, curing, etc., but excluding Formwork, complete as specified and directed. Note: 1.The blended cement i.e., PPC shall not have more than 25% of pozzolanas.
Reinforced Cement Concrete by insitu mixing using Weigh Batching or RMC of Ultra Tech, Birla Ready Mix of Grade M - 30 (Minimum Cementitious Content not less than 350 Kg/Cum) up to specified level using Portland Pozzolana Cement conforming to IS 1489 Part-1 (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, Andhra Cements Ltd., KCP make) with crushed stone sand and graded stone aggregates of 20mm maximum size including mixing superplasticizer of brand M/s. Fosroc, Demech, Huntsman, Pidilite, Sunanda Chemicals, Agro Chemicals, MBT in proportion as per Manufacturer's Specifications, Pumping / Lifting of concrete to the required heights, Concrete laid to proper level, profile and slope, placing concrete, consolidation, finishing, curing, etc., but excluding Formwork and reinforcement as specified and directed. Note: 1.The blended cement i.e., PPC shall not have more than 25% of pozzolanas.
Below FFL including grade slab
Above FFL
Casting and fixing in position precast reinforced cement concrete covers of required size in RCC M-20 insitu mixing BY WEIGH BATCHER using ordinary Portland Cement conforming to IS 8112 (M/s. ACC, Ultra Tech, Raasi, Birla, Coramandal, M/s. Andhra Cement Ltd., KCP), crushed stone sand , graded stone aggregate of 10 mm maximum size at and at all depths and heights below and above plinth level including mixing superplastizer (M/s. Fosroc, Demach, Huntsman, Pedilite, Sunanda Chemicals, Agro Chemicals, MBT) in proportion as per manufacturer’s specifications including necessary shuttering, providing and fixing cover blocks of required sizes, consolidation finishing as specified, curing, making casting yard and curing tank, stacking carefully at casting yard and transporting to the site of use placing in position as shown in drawings, aligning, leveling, making good all the damaged surfaces etc., complete as directed for covers for storm water drains/trenches with and without holes including formwork but excluding reinforcement Note: 1.The blended cement i.e., PPC shall not have more than 25% of pozzolanas.
III. FORM WORK :
Providing centering and shuttering using 12mm thick marine plyboard at all depths and heights below and above plinth level, vertical, horizontal, inclined,circular including strutting, propping using steel pipes/acro stagging, removal, cleaning of the same for insitu reinforced cement concrete and in plain cement concrete work, pockets for machine/equipmet foundations as required including chamfers, splays, keys, wedges, nails, bracings, brackets and applying one coat of shuttering oil on all shuttering surfaces coming in contact with concrete etc., complete as directed. Note :- Plywood shall not be used for more than eight repitions.
a) Below and Upto Finish Floor Level
b) Above Finish Floor Level
IV. REINFORCEMENT & STRUCTURAL STEEL
Supply, fabrication and erection of Reinforcement bars for Reinforced cement concrete items at and at all depths and heights below and above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more conforming to IS 1786 of Tata, Vizag,Sail, JSW make, including transport to site, loading and unloading, making fan hooks of required shape, dowels for bonding masonry, transporting steel to site, decoiling, removing of scales, straightening, cutting, bending, fixing bars with chairs, space bars wherever required, in position with two strings of 18 gauge soft drawn annealed MS binding wire inclusive of its supply etc., complete as specified and directed.
Supply, Fabrication and Erection of Structural Steel work using Rolled Steel Joists, Beams, Channels, Plates, etc., at all levels above and below plinth level including supplying of steel sections and plates conforming to BIS 2062 of make Vizag Steel, Tata, SAIL, Jindal Ispat or any other approved manufacturer using ingots of above manufacturer make, loading, unloading, transporting the steel to site of work, cutting, fabricating using welding/bolts, using weld rods of make D&H, Advani, Philips or its approved equivalent and/or bolts and nuts from approved source, erecting using derricks/pulleys/cranes or any suitable means, fixing in position and painting with one coat of approved red oxide zinc chromate primer and two coats of Synthetic Enamel paint as per manufacturers Specifications of make Asian Paint, Berger, Johnson and Nickelson, Nerolac, cleaning the sections /plates by suitable means, etc., complete as directed by the Engineer-in-Charge.
Using rolled sections
Using Plates upto 12 MM thickness
Supplying, fabricating, erecting and fixing in position, MS insert plates/ embedded plates/pipes in medium quality conforming to relevant BIS codes of required shape and size, welding anchoring legs not less than 12mm dia MS rods, placing in position in concrete while casting, including painting with one coat of approved red oxide zinc chromate primer as per drawing in line, level and plumb complete as directed.
Supply, Fabrication and Erection of Structural Steel work using tubular sections (Round, Square, Rectangular Hollow tubes) at all levels above and below plinth level including supplying of steel sections a conforming to IS:4923 and IS:1161 of make Tata Structura , or any other approved manufacturer using ingots of above manufacturer make, loading, unloading, transporting the steel to site of work, cutting, fabricating using welding/bolts, using weld rods of make D&H, Advani, Philips or its approved equivalent and/or bolts and nuts from approved source, erecting using derricks/pulleys/cranes or any suitable means, fixing in position and painting with one coat of approved red oxide zinc chromate primer and two coats of Synthetic Enamel paint as per manufacturers Specifications of make Asian Paint, Berger, Johnson and Nickelson, Nerolac, cleaning the sections /plates by suitable means, etc., complete as directed by the Engineer-in-Charge.
V. PRE-ENGINEERING STRUCTURE :
Design, Supplying, fabricating at Factory , erecting and fixing in position , Pre Engineered Frames, Purlins, Side cladding runners (Girts), sky lights, roof extractors, ventilators etc., by cutting, welding, straightening at workshop, conveying, assembling, erecting at work site at all levels by bolts and nuts including subsequent field welding, drilling, grinding, bolting wherever required and hoisting in position for structural steel work. The job includes provision of cold formed sectional members for Z purlins/girts, pre-engineered frames using M.S Plates, tie beams, catwalk, crane girders, platforms, ladders for the members wherever required as per design, suitable supporting system for fixing polycarbonate/translucent sheeting to prevent dislodging etc., complete as specified and directed. Note :- 1) PEB shall be manufactured from dedicated workshop with a minimum capcity of 25000MT/Year and the same shall be approved by department prior to design etc. 2) Analysis and design and revisions of same if any shall be submitted for approval of department . Drawings for construction, fabrication etc. shall be provided by bidder as per EIC instructions (Nos. & Size of Hard Copies Drawings) at no extra cost. The drawings etc. will be property of department. Soft copy of analysis, design and drawings shall also be provided to the department at no extra cost. 3) The stagging/mobile scaffold/ crane/net etc required for safe erection of steel works at all heights shall be included in the rates quoted and no extra will be paid for safe working.
Primary Structural Steel Members including rafters, columns, Crane Gantries, etc., of built up sections made out of M.S Plates having minimum thickness of 6.00mm and minimum strength not less than Grade E 350 and Quality "C" as per the Table -1 of IS 2062 : 2011 to relavent ASTM manufactured by M/s. Tata, Vizag Steel, Jindal, SAIL make including painting with 2 (Two) coats of synthetic enamel paint over 1(One) coat of Zinc Chromate primer of make M/s. Asian Paints, Johnson and Nickelson, Berger, Nerolac, etc., including welding with submerged MIG/MAG welding in a well established workshop using electrodes or fillers of make M/s. L&T, D&H, Advani, etc., transportation of members to site, bolting/ welding at field by MIG/MAG, erecting members using suitable cranes/jigs/pulleys in line , level, plumb etc., complete as specified and directed by EIC. NOTE: The bolts used shall conform to A325 ASTM standards equivalent to 8.8 designation High tensile bolts conforming to IS 1367:2002
Supplying, fabricating, erecting and fixing in position walking platforms, stairs/ladders, bracings, pipe & cable supporting system as required/as per design using standard steel sections like joists, angles, channels, etc., of M/s. Tata, Vizag Steel, Jindal, SAIL make or any approved manufacturer using ingots of above makes of strength not less than Grade 250 and Quality "C" as per Table-1 of IS-2062:2011 including providing Bolts and Nuts and other accessories wherever required, arc welding, painting with 2 (Two) coats of synthetic enamel paint over One (1) coat of Zinc Chromate primer of make M/s. Asian Paints, Johnson and Nicklson, Berger, Nerolac, etc., complete as specified and directed by EIC. NOTE: The bolts used shall conform to A325 ASTM standards equivalent to 8.8 designation High tensile bolts conforming to IS 1367:2002
Supplying, fabricating, erecting and fixing in position, foundation bolts using MS rounds of make M/s Tata, Vizag Steel, Jindal or approved equivalent conforming to IS 432 and suitable nuts including threading, placing in position in concrete in level using template, providing grease and protective cover like covering with polyethelene sheet to bolts and nuts to correct levels complete and as directed by EIC.
Secondary Structural members including Purlins, Girt members, Eaves, Struts, Ridges and other items made out of Galvalume cold rolled sheets of Z shape not less than 2.5mm thickness of strength not less than Grade E 350 and Quality "C" as per the Table -1 of IS 2062 : 2011 manufactured by M/s. Tata, Vizag Steel, Jindal, SAIL make including galvanizing as per relevant IS code and coating not less than 275 g/m2 , fixing to main members using Bolts and Nuts conforming to A325 ASTM standards equivalent to 8.8 designation High tensile bolts conforming to IS 1367:2002 including overlaps, etc., all complete as specified and directed by EIC. Note: Overlaps will not be measured for payment.
Providing and Fixing Trapezoidal profiled Galvalume Sheets for roofings and claddings using sheets in 0.5mm TCT (Total Coated Thickness) and strength not less than 500 N/Sqmm including flashings, corners, ridges, eaves boards,gutters etc., of approved make including fixing the sheets with Stainless Steel self tapping, self drilling and self fastening screws, and EPDM Washers, etc., all complete as directed. for Roofing and cladding with colour coated Galvalume sheets & Rain water pipes, etc.
Polycarbonate Sheeting of 1.5 mm thick, Pressed to matching trough Corrugations of roofing/cladding of GE make, Everest or any other approved equivalent make for sky lights including sealing around sheets with GE Siliconates or any other sealants, treating for rain proof, fixing sheeting with SS self tapping screws etc., complete as directed and specified by EIC.
VI. STONE MASONRY :
Random rubble stone masonry using approved local stones in foundations/pedestals and plinth at and at all depths below finished floor level in cement mortar 1:6 (1 cement :6 using crushed stone sand of grade conforming to BIS 2116) including simultaneous flush pointing with the same mortar, bond stones, curing, etc., using crushed stone sand of grade conforming to BIS 2116, complete as specified and directed.
Random rubble stone masonry using approved local stones in foundations/pedestals and plinth at and at all heights finished floor level in cement mortar 1:6 (1 cement :6 using crushed stone sand of grade conforming to BIS 2116) including simultaneous flush pointing with the same mortar, bond stones, curing, etc., using crushed stone sand of grade conforming to BIS 2116, complete as specified and directed.
VII. BRICK MASONRY :
Brick work using quality flyash (non modular) bricks of class designation 7.5 conforming to IS12894 using cement mortar 1:6 (1 cement :6 using crushed stone sand of grade conforming to BIS 2116) at and at all depths below plinth level in foundation and in plinth, storm water drains, etc., simultaneous pointing with same mortar below ground level, and ranking out joints above ground level, curing etc., complete as per specifications and as directed for sub structure etc.,
Brick work using quality flyash bricks of class designation 7.5 conforming to IS12894 using cement mortar 1:6 (1 cement :6 using crushed stone sand of grade conforming to BIS 2116 ) at all depths and heights below and above plinth level including pilasters, steel / tubular scaffolding, raking out joints, curing etc., complete as per specifications and as directed in super structure.
Half brick masonry using non modular fly ash bricks of class designation 10, conforming to IS :12894 in partition walls in cement mortar 1:4 (1 cement :4 using crushed stone sand of grade conforming to BIS 2116) all depths and heights below and above plinth level including scaffolding, raking out joints, curing, etc., complete including providing stiffeners of reinforced cement concrete 1:2:4, 115 mm x 75 mm size at every 900 mm height, necessary formwork, curing, etc., complete as per specifications and as directed but excluding reinforcement. Note:- Reinforcement will be paid under relevant item.
VIII FLOORING :
Construction of Granular sub-base by providing HBG material conforming to Grading-ii of MoRTH Table 400-1 including cost, charges and conveyance of all materials to work site and spreading in uniform layers with motor grader or by approved means, on prepared surface mixing by mix in place method with Rotavatopr/approved means at OMC and compacting with 8 to 10 tonnes roller to achieve the desired density etc., complete for finished item of work as per MoRTH Specification 401(5th revision and as directed by Engineer-in- Charge. Note: ( Payment will be made based on levels for finished item of work).
Cutting using Diamond saw or any other suitable equipment grooves of size 6mmx12mm in flooring at construction/contraction joints or as directed by design Engineer, including sealing with polysulphide sealant, cleaning the joints using compressed air, drying the joint before application complete as directed.
Providing and laying at all floors and levels 6mm (min) thick first quality glossy/ matt / antiskid/rustic / digital collection etc. ceramic tile flooring as per the approved pattern and colour as mentioned below conforming to IS 15622 latest of edition from approved list of maufacturers or equilvalent laid in cement mortar bedding / backing, close jointed and grouted with matching cement slurry to match the colour of the tiles, finished to level, line, slope and plumb including cutting of tiles, making openings/cutout if necessary, wastage and final cleaning of surfaces as required, curing etc.complete all as per drawing specifications & as directed by Engineer in charge. a) In flooring with rustic/matt finished/ 300x300mm, 600 x 600mm or equivalent approved sizes of ceramic tile laid over 20mm thick cement mortar bedding 1:4 ( 1 cement : 4 sand) b) In skirting laid over 12 mm thick CM 1:3 backing. c) Anti skid ceramic tile with 300x300 or equivalent approved sizes of ceramic tile laid over 20/15mm thick cement mortar bedding 1:4. In dado / clading with tile of size 200x300mm or size as per working drawing laid over 12 mm thick CM 1:3 backing for toilets. d) Sand shall be crushed stone sand. e) Tiles shall be of make Kajaria/Regency/Somani/Jhonson & Jhonson Note: i) Quoted rate shall include extra cement mortar required to match the water proofing plaster if any to maintain the lines and plumb of dado. ii) The quoted rate shall include border / combination of tiles as instructed by the Engineer in Charge iii)The sizes of tiles mentioned are approximate and subject to the availability in market during execution. If the required size is not available the next higher size of tiles shall be used without any extra cost to the Department. The tenderer may note the same and quote accordingly.
Anti skid ceramic tile with 300x300 or equivalent approved sizes of ceramic tile laid over 20/15mm thick cement mortar bedding 1:4. for toilets
In dado / clading with tile of size 200x300mm or size as per working drawing laid over 12 mm thick CM 1:3 backing for toilets.
Providing and laying double charged vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make like Kajaria/Regency/Somani/Jhonson & Jhonson , in all colours and shades, laid cement mortar , jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete for entrance foyer, corridors, lobbies, etc. Note: i) Quoted rate shall include extra cement mortar required to match the water proofing plaster if any to maintain the lines and plumb of dado. ii) The quoted rate shall include border / combination of tiles as instructed by the Engineer in Charge iii)The sizes of tiles mentioned are approximate and subject to the availability in market during execution. If the required size is not available the next higher size of tiles shall be used without any extra cost to the Department. The tenderer may note the same and quote accordingly.
In flooring with rustic/matt finished/ 800X800 mm or equivalent approved sizes of double charged vitrified tile of make Somany/Kajari or approved equivalent laid over 20mm thick cement mortar bedding 1:4 ( 1 cement : 4 sand)
In skirting laid over 12 mm thick CM 1:3 backing.
Cement concrete flooring IPS 40 mm thick 1:2:4 (1 cement : 2 coarse crushed stone sand : 4 graded stone aggregate) with 10mm thick nominal stone aggregate finished with a floating coat of neat cement, including cement slurry, including the cost of nosing of steps etc. complete.
Provdidng 18mm thick Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse crushed stone sand), finished with a floating coat of neat cement complete as specified and directed
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut Granite stone(with flaming) for floor/treads/ risers /steps / dado ramps of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse crushed stone sand)/ 12 mm thick, 1:3 (1 cement : 3 coarse crushed stone sand) cement mortar for risers joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels for stair case & counter wash basin etc. including cost of nosing and grooves for antislippery measure complete as specified and directed
Providing and filling with polysulphide sealant of 25 X 25 mm size in the joints cut in expansion joint etc., directed by engineering's-in-charge.
IX. DOORS, WINDOWS & ROLLING SHUTTERS ETC :
Providing and fixing factory made uPVC white colour sliding cum fixed glazed windows/ventilators comprising of uPVC multi-chambered frame three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm, duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), including providing and fixing double glazing made of 6mm thick toughened glass with a 15mm gap dully filled with argon,, uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc including providing and fixing double glazing made of 6mm thick toughened glass with a minimum 08 mm gap dully filled with argon. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge including Single / double glass panes and silicon sealant. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.
Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, with decorative lamination on both sides in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge.
X. PLASTERING AND POINTING :
Cement plastering 15 mm thick for internal walls in cement mortar 1:4 (1 cement :4 river sand) , and at all heights above plinth level over brick walls or concrete surfaces including making necessary grooves in between junctions of brick masonry and RCC and also other places wherever required over brick walls or concrete surface, preparation of surface, steel/tubular scaffolding, curing, etc., complete as directed.
Sand faced plaster 20 mm thick in 2 coats over exterior masonry and concrete surfaces at and at all heights above plinth level as given below with base coat in cement mortar 1:4 with approved integrated water proofing compound @ 2% by weight of cement, of M/s. Fosroc/Demach/ Huntsman/ Pedilite/ SIKA Qualcrete / MBT or as per manufacturer’s specifications, 12 mm thick and finishing coat in CM 1:3, 8 mm thick, final rendering, making necessary grooves, bands, drip moulds as required, finished smooth internal putty(lapam) of Birla/Jk of not less than thickness 1mm(one) thicknes) double steel/tubular scaffolding wherever necessary, hacking of concrete surfaces, curing, etc., complete as specified and directed.
Providing and applying white cement based putty in two coats with average thickness not less than 1 mm, of Birla make or any other approved manufacturer, over the plastered wall surface (external/internal) to prepare the surface even and smooth complete.
Providing Raised/Cut Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine river sand) including preperation of surface complete as specified and directed.
Forming groove of uniform size from 12x12mm and upto 25x15mm in plastered surface as per approved pattern using wooden battens,nailed to the under layer including removal of wooden battens,repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-charge.
XI. PAINTING:
Painting exterior walls on sand faced plaster with two coats of Alkali & fungal resistance, dirt resistance exterior paint with comprehensive warranty of 5 years of required shade of Makes Asian - Apex Advanced or equivalent in Pidilite, Johnson & Nicklson, Nerolac, berger, of exterior quality haying 100% acrylic, of approved shade including preparing surfaces, external putty of Birla or its approved equivalent wherever required applying one coat of approved primer as per manufacturers specification, applying and filling cracks or wherever required for external filler, curing, scaffolding, cleaning, etc., complete. Note :- Minimum Usage Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. or as per manufacturer's specification
Painting exterior walls on sand faced plaster with two coats of textured exterior paint of Asian , Pidilite, Johnson & Nicklson, Nerolac, berger, of exterior quality , of approved shade including preparing surfaces, external putty of Birla or its approved equivalent wherever required applying one coat of approved primer as per manufacturers specification, applying and filling cracks or wherever required for external filler, curing, scaffolding, cleaning, etc., complete.
XII. MISCELLANEOUS ITEMS :
Providing and fixing SS railing made out of commercial chromium steel tubes SS 304, of various diameters, of approved make, 2 mm wall thickness, pattern as shown in drawing/as directed including supplying or fabricating, fittings like SS bends, tees, etc., welding the pipes using TIG welding or any other approved method, grinding/buffing the welded joints smooth, erecting the railing in position in line, level and plumb, fixing tailing in position by grouting/or any approved system, cleaning, polishing the joints if required, scaffolding etc., complete all as specified and directed.
Providing and fixing CI gratings conforming to IS 1729 for rain water pipe entry mouths/filter bed, etc., including chasing making holes in existing masonry concrete surfaces, refilling with cement concrete 1:2:4 reinstating to the original conditions, painting with two coats of bitumastic paint, all in level and line complete as directed and specified for rain water mouths, filter bed.
Providing grouting (including tamping) for foundations, structures, equipments, base plates, anchor holes, etc., with non-shrink, free flow grout of shrinkhomp-30N/Sqmm of M/S A.C.C, Fosroc or equivalent mixed with filler like sand in 1:1, including shuttering wherever necessary at and at all depths and heights below and above plinth level complete as specified and directed. note: Weight of grout used in the work will be measured for payment. However, the rate quoted shall inclusive of all materials.
Providing and fixing 160 mm n.b.un-plasticised PVC rain water pipes with necessary PVC clamps and wooden gutties of approved make conforming to IS: 13592 type ‘A’with injection moulded fittings jointing with approved synthetic adhesive seal rings conforming to IS: 5382 embedding the slab junctions leakproof testing complete in line, level and plumb all as directed.
Providing and fixing G.I. chain link fabric fencing, made of G.I. wire of dia not less than 4.00 mm of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.
Providing, fabricating, supplying and fixing 4mm thick panels of aluminum composite panel cladding in metallic colour of approved shades made out of 4mm thick aluminum composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminum sheets (each 0.5mm thick), of make Eurobond/ Deltyn Sheet Fixing with Paper Joint As per Design complete as directed by Engineer-in-charge.
Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin- charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding.
Supplying and installation of MS Rafters of SIZE 2" x 4" 2mm thk of APOLLO make pipe or equivalent with minimum 50 mm thick Grey powder Coating as per design complete as directed by Engineer-in-charge. .
Supplying, fabricating and installing of MS Gate of required size using MS sections of Apollo or equivalent make, consisiting of MS sheet at bottom, including suppplying and fixing of vertical post, track into the pavement consisting of 20mm bright rod and C-channel, welding using weld rods of make D&H, Advani, Philips including Supplying and fixing of Electromechanical motor and other accessories with built in digital controller, magnetic limit switch, digital native encoder, suitable for super intensive use for sliding gates weighing upto 1600 KG, remote & reciever, push button along with pair of photo cell sensors and alarm lamp, as directed by Engineer-in-charge. Note: Supplying and laying of cable including any accessories required for installing push button any excavation and concreting or other miscellaneous works required for fixing of item no. 4 shall be included in the cost.
CERA BOARD FALSE CEILING :- Providing & fixing suspended CERA board false ceiling which includes GI perimeter channels along with the perimeter of ceiling, screw fixed to brick wall with nylong sleeves & screws at 610 mm centre. The suspending GI intermeditae channels of size 45mm (with two flanges of 15 mm each) single layer of 12.5 mm trapped edge with gypboard plain (Confirming to IS 2095 Part-1 Latest edition) and screw fixed to ceiling section with 25mm dry wall screws at 230mm centre painted with two coats of acrylic washable distemper over one coat of primer of required shade and one coat of putty if required including cutting the sheets to required size, providing extra frame work around light fittings , A.C grills and for trap doors fixed with necessary clips and accessories to correct line and levels including scaffolding etc. complete as specified and directed
Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.
Electrification :- Providing electrification and Providing copper wiring of sizes 4sqmm/2.5 sqmm /1.5 Sqmm or as required for electrical installations of finolex make and modular switches and sockets of legrand/gold medal make ,cable conduits and RJ 11 sockets as required includings Philips Lighting and all complete as per design and as specified & directed by EIC
Fencing Work :- Supplying, fabrication and erection of powder coated hollow structural steel by using MS tube of Apollo or equivalent make with frame using flats at all levels above plinth level as per design including bolting/welding using weld rods of make D&H, Advani, Philips, complete as directed by Engineer-in-charge.
XIII: DISMANTLING ITEMS:
Dismantling/breaking the existing plain cement concrete surfaces carefully in flooring, platforms etc. to the required size, using pneumatic cutters or any approved means including disposing of debris within a distance of 50 m etc., complete as specified and directed.
Dismantling very carefully the existing reinforced cement concrete at all depths and heights below and above plinth level using pneumatic cutters or any approved means including cutting the reinforcement and transporting bars to departmental stores disposing the debris within the lead of 50 m complete as specified and directed
Dismantling very carefully the existing Brick masonry in cement motor with plastering on both sides very carefully at depths/heights above/below plinth level by suitable methods including erection of suitable scaffolding, stacing of useful materials and disposing the unserviceable debris within the lead of 50m, etc., complete as specified and directed.
Dismantling very carefully the existing RR masonry below/above FFL at all depths and heights including erection of suitable scaffolding, stacking of useful materials and disposing the the unserviceable debris within the lead of 50m etc., complete as specified and directed,
Dismantling very carefully the existing structural steel work at all levels in MS structural sections like angles, channels, MS plain/chequered plates, flats,MS gates etc., including scaffolding, cutting of structural steel members by gas cutters or by any approved method, removing the nuts, bolts etc., as required, lowering stacking the reusable material at site and transporting the material to Departmental stores etc., complete as directed
Removing carefully existing chainlink fabric from angle iron posts and struts by removing hook bolts, nuts, etc, straightening GI rods (vertical as well as horizontals) etc., rolling back the removed chainlink, collecting hooks, bolts and nuts, stacking including cutting of iron angle posts, dismantling of PCC pedestals, transporting the materials to Departmental stores etc., complete as directed by Engineer-in-charge. Note: Area of the chain link fabric will be measured for payment.
Removing soling from flooring/pavement, stacking useful materials like stones within 50m lead, disposing of unserviceable materials as directed.
Removal of existing fire hydrant line of 50/80/100/150/200/250/300 mm n.b., including fire hydrant/ hoses/ box for keeping hoses etc. excavating the equired length, cutting the pipe line after shutdown, handling over the pipe line to the departmental stores. Note: Earthwork excavation required for the work will be measured under relevant item.
Dismantling very carefully the existing MS/GI/CI pipe of various dia for various services/hand rail with all fittings and fixtures etc., and stacking with in a lead of 250 m.
a) Upto 150 mm dia.
b) Above 150 mm dia up to 300 mm dia
Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material and stacking as per EIC for all leads.
Demolishing stone/ tile/IPS flooring including stacking of serviceable material and disposal of unserviceable material within any lead complete as per directions of Engineer-in- Charge
Dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking of serviceable material and stacking as per EIC for all leads.
JVS ENGINEERING AND CONSTRUCTIONS PRIVTE LIMITED
SRI PERLA CONSTRUCTIONS
BAJAJ STEEL INDUSTRIES LIMITED
stage.html
html • 0.02 MB
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .