CA NO GE(N)AMB-46/2024-25 PETTY REPAIR/DAY TO DAY MAINT WORKS IN JCOS/ORS MD ACCN-III AGE B/R-I OF GE (N) AMBALA CANTT

Amount

Cleaning and removing all scale and dirt, etc from existing water storage tanks of capacity exceeding 250 litres and not exceeding 500 litres by emptying, drying and cleaning the tank by scrubbing the dust with wire brush from tank including cleaning from mouths of circulating pipes & writing on the tank with synthetic enamel paint not less than 200mm in height and 20mm wide of words in shape like cleaned on : 15.06.2024 to entire satisfaction of Engr-in–charge complete all as specified. (The rates includes for disconnecting of existing water tank, lowering if required and hoisting, reconnecting and refixing in same position after cleaning ) Note- The whole process of disconnecting, reconnecting and refixing in same position after cleaning shall be done on the same day, if failing so, Rs. 1000/- shall be deducted for each tank per day from the contractor due.

Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc., complete, all as specified and as directed by the Engineer–in–Charge.

M&L for rendering 15mm thick in cement plaster (1:4) on any faces of brick work or concrete wall surfaces and finished even and smooth without using extra cement up to height of double storey bldg, including necessary scaffolding etc., complete all as specified and as directed by the Engineer–in–Charge.

M&L for rendering 15mm thick in cement plaster (1:6) on any faces of brick work or concrete wall surfaces and finished even and smooth without using extra cement up to height of double storey bldg, including necessary scaffolding etc complete all as specified and as directed by the Engineer–in charge.

M&L for rendering 5 mm thick on ceiling surfaces of brick work or concrete wall surfaces in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer–in–Charge.

M&L for preparation of new plastered /concrete surface of wall applying of two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of new plaster surface on walls and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of new plastered surface of ceilling applying three coats white wash, complete all as specified and directed.

M&L for preparation of old treated surfaces of walls, cornices etc. (plastered or unplastered) by brooming down, steel wire brushing, scraping down smoke soot, moulds, moss, efflorescence salts, trading oil and greasy spots etc, up to any height of including necessary scaffolding and applying one coat of oil bound distemper on wall surface etc., complete, all as specified and as directed

M&L for preparation of old plastered surface of ceilling applying one coat white wash, complete all as specified and directed.

M&L for preparation of old wooden painted surfaces and applying one coats of synthetic enamel paint on wooden surfaces of any description, not otherwise described, over 10cm width or girth complete, all as specified and as directed.

M&L preparation of old painted steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed by the Engineer–in–Charge.

M&L for preparation of new or previously untreated surfaces of wooden and applying two coats of synthetic enamel paint over and including a coat of pink primer on wooden surfaces of any description, not otherwise described, over 10cm width or girth complete all as specified and as directed.

M&L preparation of new steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over and incuding a coat of red oxide primer complete all as specified and as directed by the Engineer–in–Charge.

M&L for preparation of new /old plastered surfaces of wall and applying 02mm thick wall care putty white cement based to achieve smooth surface in 2-3 coats complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exe 15 cm thickness (below or above ground level) complete, all as specified and as directed

Material and labour for 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded mechanically crushed stone aggregate) as in sub base to floor /hardstanding etc finished even and fair, complete all as specified and directed.

M&L for providing 50 mm thick cement concrete 1:3:6, type C–1 (using 20mm graded crushed stone aggregates) as in plinth protection laid in alternate bays (n exc 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight, complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4, type B–0 (using 12.50mm graded crushed stone aggregates) finished even and fair for levelling of floor finishes, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete, all as specified and as directed.

M&L for granite black (of any type) tiles 16 to 18mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over 15mm thick screed bed in cement mortar (1:6), as in steps, cooking platform, and including cutting 25mm dia hole for gas pipe complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations,. complete all as specified and directed.

Supply and fixing non skid ceramic colour tiles joint free premium /1st quality 7 to 8mm thick (square /rectangular) area of each tiles exc 0.06 sqm but n exe 0.11 sqm, in floor etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Supply and fixing glazed ceramic colour tiles joint free premium /1st quality in vertical surface, dado, skirting etc of size 300X600X7 to 8mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match including 10 mm thick cement plaster in cement mortar (1:4) on wall of brick /concrete surfaces, complete all as specified and directed.

M&L non skid coloured ceramic tiles joint free premium /1st quality 8 to 10 mm thick, (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and inculding 15mm thick screed bed in cement mortar (1:6), complete all as specified and directed

M&L non skid coloured ceramic tiles of 8 to 10 mm thick, of same description as of floor tiles as in serial item No 25 above but 100 to 150mm in height as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick /concrete surfaces in cement mortar (1:4), complete all as specified and directed

Material and labour for machine cut kota stone slab flooring 18 to 22 mm thick (each slab size not less than 550mm x 550mm) in floor, set and jointed in neat cement slurry with grey cement mixed with pigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L 18 to 20 mm thick machine cut kota stone slab as in skirting, riser of steps, dado & pillar verticle surfaces etc. over and including 10mm thick screed layer in cement mortar 1:4 set and jointed in neat cement slurry mixed with pigment to match the shade including grinding and polishing complete all as specified and directed.

Supply and fixing as in repair, water storage tank, 500 ltr capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm dia high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore and including 20mm bore tank nipple & one 20mm GI union at outlet and including dismantling of water tanks and removing from site all as specified in SSR Part–I complete, all as specified and as directed.

Cutting chases to brick wall built in cement mortar, pinning in making good to facing where required and pointing in CM 1:3 to edges of landing, steps, cills, sunsheds, shelves, lintel etc and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth complete all as specified and as directed by the engineer - in- charge

S&F for galvanised iron tubing 20mm bore medium grade with all fittings and fixed complete to wall and ceiling or laid in floors, including taking down of existing unserviceable GI tubing including all fittings etc complete all as specified and directed.

S&F for galvanised iron tubing 15mm bore medium grade with all fittings and fixed complete to wall and ceiling or laid in floors, including taking down of existing unserviceable GI tubing including all fittings etc complete all as specified and directed.

S&F 15mm bore cast copper alloy fancy type, chromium plated stop valves with long shank and cup (concealed type), screwed down, high pressure with capstan head, screwed both ends for iron pipe or for unions as in repair, complete, all as specified and as directed.

S&F in repair stop valves /angle valve chromium plated fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair 15mm bore pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down, fancy type high pressure, with or without lettred 'HOT or COLD' with long screwed shank and fly nuts complete all as specified and directed.

S&F in repair 15mm bore long body bib taps cast copper alloy fancy type, chromium plated, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair pvc connection 15mm size PTMT nuts of length 450mm, complete all as specified and directed.

S&F in repair vitreous china wash basin white, flat back, size 550x400 mm including cutting for pinning in ends of brackets or erecting stand, including 32mm bore pvc corrugated waste pipe 900mm long, 32mm bore waste coupling chromium plated long screwed shank and fly nuts etc., complete all as specified and directed.

S&F in repair 15mm bore shower rose chromium plated 150 x 150mm alongwith 15mm bore shower arm 195 mm long with bend of 45 degree complete all as specified and directed.

S&F in repair vitreous china squatting pan, "Orissa pattern" of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, flushing pipe, anti syphonage pipe complete all as specified and as directed by the Engineer–in–Charge.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white, incl 'P' or 'S' trap, connection to drain and flush pipe, antisyphonage pipe and including pvc seat cover closed pattern flat bottom, mild steel chromium plated or aluminised hinging device complete and as specified.

S&F mild steel chromium plated hand shower (health faucet ABS body) suitable for 15mm dia pipe with 8 mm dia 1.25 mtr long flexible tube and ABS wall hook including making connection as in repair , complete, all as specified and as directed.

Supply and fixing 10 litre capacity virgin polypropylene cistern, ISI marked, coloured at low level complete with PVC bend/flush pipe and making all connection including taking down existing high or low level unerviceable flushing cistern and making good the disturbed surface to match with the existing surface, complete all as specified and directred.

S&F in repair stainless steel grating 100mm dia with or without waste hole complete all as specified and directed.

S&F in repair for 20mm bore gun–metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair pvc water closet seat cover, white, closed pattern with flat bottom, mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S & F CP brass wall mixture 3-in-1 system for mixing hot and cold water suitable for 15mm bore pipe complete with 115 mm long bend pipe,connecting legs & wall flange and wall bracket for hand shower as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F sinks with drainage board made out of stainless steel 1mm thick sheet for kitchen or laboratory with plugs, waste pipe, brass chromium plated coupling and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm as in repair, complete, all as specified and as directed.

S&F as in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed by the Engineer–in–Charge.

S&F in repair 32 mm dia PVC waste pipe for wash hand basin /kitchen sink etc of standard length complete all as specified and as directed by the Engineer–in–Charge.

S&F as in repair 20mm bore GI unions to connecting galvanised iron pipe complete all as specified and as directed.

S&F in repair 20mm bore ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F in repair 32/40mm bore CP waste coupling full threaded suitable for kitchen sink etc of standard length complete all as specified and as directed by the Engineer–in–Charge.

Taking down chowkats or frames with shutter area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , complete, all as specified and as directed.

Taking down chowkats or frames with shutter area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish, complete, all as specified and as directed.

Taking down shutters of any description area exc 1 sqm and not exc 2 sqm and removing from site , complete, all as specified and as directed.

Taking down shutters of any description area exc 1 sqm and not exc 2 sqm each and refixing in the same opening, complete, all as specified and as directed.

M&L rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe–410–W (Grade E–250) quality 'A' , complete, all as specified and as directed.

M&L factory made 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by the Engineer–in–charge.

Supply and fixing factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be kiln seasoned and chemically pressure treated), complete, all as specified and as directed.

S&F double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutter fabricated from following sections :- (a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf . (c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mm made from 1.25 mm thick MS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt stove enamelled 150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf (vi) Pintal hinges 12 x 75 mm - 2 Nos each leaf (vii) 10mm square Guard bar @ 10 cm c/c welded to frame . (viii) Two coat of Synthetic enamel paint over one coat of red oxide primer. (ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws . (x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window. (xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessoriries as mentioned above. (iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type.

S&F powder coated aluminium section (minimum thickness of powder coating 50 micron) for doors,windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge. Note : (a). Glazing shall be measured and paid separately; (b). Weight of aluminium sections shall be as per IS or actual weight which ever less shall be measured. (c). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required and the same shall not be measured for arriving the weight; (d). The rates shall be inclusive of locking arrangement including complete packing with silicon gel all around contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F for factory made solid PVC moulded door shutters (wood free EPS) 28 to 30 mm thick (stile), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face & 2mm Plan colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing including 03 nos 100 mm long stainless steel hinges, 02 nos 150 mm aluminium handle & 02 nos 150 mm long aluminium tower bolt in each shutter complete all as specified and directed.

M&L for PCC 1:3:6, type C–0 (12.50mm graded crushed stone aggregate) as in bed blocks for hold fast & filling of pressed steel frame including necesssary formwork complete all as specified and directed.

S&F for 100mm MS Butt hinge medium weight cold rolled, complete all as specified and directed.

S&F for 150mm long aluminium, anodised, barrel tower bolt of extruded section, complete all as specified and directed.

S&F for 100mm long aluminium, anodised, barrel tower bolt of extruded section, complete all as specified and directed.

S&F for 150mm long aluminium handles, fabricated type, anodised complete, all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150mm long cover plate, complete, all as specified and directed.

S&F 300 mm long aluminium sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12 mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple and fixed complete all as specified and directed.

S&F mild steel 150 mm, ordinary rat tail rod pattern springs, including roller and roller plate including fixing to steel frame complete all as specified and directed.

S&F in repair for 150mm long aluminium handles, cast type, anodised complete all as specified and directed.

S&F in repair for 100mm MS Butt hinge medium weight, cold rolled and welding to MS chowkhats if reqd complete all as specified and directed.

S&F in repair for 150mm long aluminium, anodised, barrel tower bolt of extruded section, complete all as specified and directed.

S&F in repair 300 mm long aluminium sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12 mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple and fixed complete all as specified and directed.

M&L welding to grills, guard bars, steel windows, fixing of hinges to steel chowkhats and steel door etc., thickness of metal to be welded exc 6mm and not exceeding 9 mm and exceeding 2.5 cm and not exceeding 5.0 cm in length complete all as specified and as directed.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles , complete, all as specified and as directed.

M&L brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6, up to height of double storey bldg, including necessary scaffolding /formwork etc complete all as specified and as directed.

All as per serial item No. 80 here in befor but except bricks (old serviceable bricks obtained from serial item No 79 above including removing motar, cleaning the bricks with water,shall be used), complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work including cutting of steel reinforcement as required to facilitate demolition and removal the rubbish/ demolished material outside defence land, complete all as specified and as directed by the Engineer–in–Charge.

M&L for reinforced cement concrete (Nom mix) type B–1, 1:2:4 (20mm graded crushed stone aggregate) in chajjas and incl necessary formwork /scaffolding upto 9mtr height complete all as specified and directed

M&L for providing reinforced cement concrete type B–1, 1:2:4 (20mm graded crushed stone aggregate) in roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete with joints to match and including necessary formwork /scaffolding upto 9mtr height complete all as specified and directed

S&F mild steel TMT bar 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hopping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0,.9mm dia or screwing with clip etc all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed

S&F 3mm thick sheet glass ordinary quality with aluminium beading, rubber packing or oil putty in square n.exc 0.5sqm in each pane, complete , all as specified and directed.

S&F 3mm thick frosted sheet glass ordinary type and glazing with aluminium beading, rubber packing or oil putty in square n exc 0.5 sqm each pane complete all as specified and directed.

S&F for galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples or ms nut & bolt including removing from old steel window /door cutter /grinder or any other method complete all as specified and directed.

S&F in repair stainless steel rod of 25 mm dia, min 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets/finials fancy type, stops fixed with ss screws etc complete fixed as in repair complete all as specified and as directed by the Engineer–in–Charge. Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered.

Taking down of PVC /cast iron/RCC drain pipes /rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan–necks, etc., including where as necessary excavation, returning filling, removal etc and cleaning or refixing or removal to store, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed on wall including all fittings (branch piece,tee & coupler etc ) complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends of any radius , complete, all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes single socketed incl all necessary fitting tee,branch piece, single Y etc. in any length with rubber ring joints, laid in floor /trenches complete all as specified and as directed by the Engineer–in–Charge

S&F 75mm bore PVC (SWR) bends of any radius , complete, all as specified and as directed.

S&F in repair 75 mm PVC(SWR) floor trap with grating incl jointing to waste pipe incl fixed in cement concrete type B–1 (1:2:4) complete all as specified and as directed.

S&F continuous (piano) hinges, width of flaps 30mm (when open) mild steel bright finish or electro galvanished complete all as specified and as directed by the Engr–in–charge.

S&F for 100mm long aluminium handles, fabricated type, anodised complete, all as specified and directed.

S&F 100 mm long hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

M&L for PCC 1:5:10 type E–2 using 40mm graded crushed stone aggrgate as in filling in sunken portion floor, rounded or chamfered on edges including demolition of old PCC and removing from site complete all as specified and directed.

M&L for sunken floor water proofing treatment complete all as under :– (A) Scrapping the surface with wire brush and cleaning with water and allow to dry. (B) Applying cement slurry @ 3 kg/sqm duly mixed with water proofing compound. (C) 15 mm thick cement plaster 1:3 mixed with water proofing compound as per manufacture instruction (the corner will made rounded in concave shape). (D) Apply one coat of hot bitumin grade 85/25 conforming to IS 702 @ 1.5 kg/sqm. (E) Supply and laying APP with non woven polyster reinforced sheet 3mm thick weight not less than 3.00 kg/sqm. (F) Applying one coat of hot blown bitumin grade 85/25 conforming to IS–702 @1.50 kg/sqm. (G) Curing the sunken portion with water min 48 hours by ponding. (H) Fixing 50mm bore GI pipe medium grade as in spout of 0.60 mtr length in each sunken.

Supply and fixing of 18mm thick PVC sheet having one side decorative laminated sheet and one side plain white as in cupboard, cabinet, panel, shelves, sides etc. fabricated using adhesive and SS screws including 2mm thick edge bonding tape or 90 degree edge bent on edges including dismantling of existing board any type complete all as specified and directed. NOTE: – Material manufacture test certificate should be provided before execution of work.

S&F in repair 15 mm bore spindle for Bib Tap /Angle Cock /concealed stop cock etc of standard length complete all as specified and as directed by the Engineer–in–Charge.

S&F in repair pvc flushing cistern internal fittings complete (syphone, lever, ball float valve and rubber washer or gasket etc) of 10 ltr capacity complete all as specified and directed.

S&F as in repair PVC tank lid/cover suitable for capacity 500 /1000 ltrs with and including locking arrangments such as nuts, bolts etc complete all as specified and as directed by the Engineer–in–Charge.

S&F in repair stainless steel kitchen plate rack made out of 0.63mm thick stainless steel of grade SS304 of size not less than 786 mm x 914mm x 264mm, including screws and fixing arrangements complete all as specified and directed.

S&F in repair glass corner shelf 8mm thick including CP railing radius 200mm complete all as specified and directed by Engineer–in–Charge.

S&F as in repair mild steel door shutter two leaves with frame of 20 gauge MS sheet (all around) and leaves of 21 gauge MS Sheet (all as per godrej pattern) with three way locking arrangement with brass lock with duplicate key and CP handle including two coats of spray painting over a coat or red oxide primer complete fixed in existing cupboard fixed with necessary nuts, bolts including embedded in PCC 1:2:4 (area of opening shall be measured) complete all as specified and as directed by the Engineer–in–Charge.

M&L for factory made precast RCC manhole covers with frame (type A-1, 1:1½:3, using 20 mm graded stone aggregates), of size 900mm x 600mm x 70mm with plain faces, including 70x3mm ms flat all around and incl reinforcement, set in cement mortar 1:4 complete all as specified and as directed. Make :- Venus, Gurunank Spun pipe, BRHC

M&L for cleaning of sewage line upto first man holes by any means and removing blockage of WC, EWC, Bathroom, floor trap of WHB/Kitchen pipe etc including first man hole complete all as specified and as directed by the Engineer–in–Charge.

M&L for cleaning of manhole or gully trap of any size, type and any depth and removing the sludge /solid content from the manhole or pit by manual /mechanical method or any other suitable means at the discretion of the contractor at his own arrangements including flushing with fresh water and make the manhole or pit fully functional to the entire satisfaction of Engineer-in-Charge also to remove the sludge/solid contents out of defence land including covering with a layer of lime and further earth filling and respositioning of the RCC /CI cover slab all as directed by the Engineer-in-Charge.

Note for Item No. 111 to 112 :– (i) Contractor or his authorised rep will report daily at 0830 hrs and onwards at complaint cell for collection of complaints from the concerned JE's in charge and distribute all complaints/ detailing to his tradesmen, monitoring the work done and taking the complaint slip back from trademans on every working day, re–submit the same to JE's in charge after rectifying the complaint at complaint cell, failing which a recovery of Rs 1000/– per day shall immediately be effected from the contractor's dues in terms of conditions 25, 44 & 45 of IAFW–2249 (General Conditions of contracts). (ii) The complaint shall be attended & defect shall be rectified within 08 hrs i.e from 0900 hrs to 1700 hrs (excluding sunday & gazetted holiday), commencing from date and time of notifying the complaint slip failing which a penalty @ Rs.120/– per complaint per day (08 hrs) shall be levied upon/imposed on the contractor and necessary recovery shall be effected from his dues on this account. In case, after checking & attending the defects, if it is not possible to rectify the defect within 08 hrs, the fact shall be brought to the notice of Engr–in–Charge by the contractor/ his rep immediately and if Engineer–in–Charge is satisfied with the facts brought by the contractor, no recovery shall be made on this account. (iii) All T&P required for attending the complaints shall be provided by the contractor without any extra. (iv) The mason shall always be in possession of all mason tools like trowel, plumb, hammer, chisel etc. as required at site or will be arrange by contractor on site on own expenditure and deemed to be included uin quoted rates. (v) The above all aspect shall be deemed to be included in the quoted rate of the respective item. (vi) All the complaint slip, register & other connected documents will be provided and maintained by contractor. (vii) Proper record (date wise) of complaints received & rectified by the contractor and attendance register of tradesman shall be maintained and may be asked for the verification at the time of payment of each RAR/Bill.

Note:- Amount of credit of Rs. 75,390.00 for retrieved materials is mentioned in Schedule of Credit Page No.121 to 122. of tender documents in pdf form which will be deducted offline while acceptance of tender.

Ashwani Kumar (BID ID -3138063)

Peerzada And Sons (BID ID -3143438)

dhingra builders (BID ID -3149992)