SPECIAL REPAIR TO BLDG No P-54 AND P-55 OF INT AND FS UNIT AND OTHER SANCTIONED WORK UNDER THE AREA OF AGE B/R-I OF GE (ARMY) No. 1 JODHPUR

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed.

Demolition of brick / block or stone / boulder masonry walling built in cement mortar including all quoins arches pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed.

Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out in soft or loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out dense/hard soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed.

Removal of excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M&L for Plain cement concrete 1:4:8 type D-2 by using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete, in flooring path, sub foundation etc, complete all as specified and as directed .

M & L for Precast cement concrete solid building block masonry 1:2:4 type B1 (using 20mm graded stone aggregates) or slabs 10cm thick with plain, joints setting in CM 1:6 complete all as specified and directed.

M&L for preparing newly plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of primer, Priming the plastered and other surface with alkali resistant priming paint complete all as specified and as directed.

M&L for mild steel tubular trusses including special shaped washer etc complete using ERW or including butt welded tubes confirming to IS 1161-1979 complete all as specified and directed.

M & L for hardcore of broken stone or boulders of gauge n exc 63mm deposited, spread levelled in layers n exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for 75mm thick Plain Cement Concrete Type C2, 1:3:6 (using 40 mm graded stone aggregate) in sub base, floors, pavings to receive floor finishes complete all as specified and directed by Engr-in-charge.

M & L for 25mm thick Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) in sub base, floors, pavings as under the layer of floor finish complete all as specified and directed.

M&L Machine cut kota stone slab 20-25mm thick as in floor laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including M&L for 20mm thick screed bed or bedding layer of CM 1:6, complete all as specified and as directed.

M&L for chequered cement concrete tiles, rubber moulded 20cm x 20cm x 25 mm thick as in floor, set and jointed in neat cement slurry and pointed with coloured cement to mach the shade and laid over 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

S&F for 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and as directed.

M & L Plain Cement Concrete Type C2 1:3:6 (using 40mm graded stone aggregate) in surface channels and drains complete all as specified and directed.

M&L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc. complete all as specified and directed.

Taking down existing cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

Taking down Chowkats or frames exceeding 1.5 Sq. M each and n exceeding 4.0 Sqm each (Without taking off shutters from the frames) complete all as specified and directed by Engr-in-charge.

Taking down steel window / ventilator complete all as directed.

M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed.

All as per item No. 23.00 here-in-above, but except stone

Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface n exc 20mm and dressing face beds and joints, complete all as specified and directed.

M&L for PCC solid building blocks 10cm thick type B1 1:2:4 set in CM 1:6 complete all as specified and directed.

M & L for 25mm thick Plain Cement Concrete Type B0 1:2:4 (using 12.5 mm graded stone aggregate) in sub base, floors, pavings complete all as specified and directed by Engr-in-charge.

M & L for Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc including over 15 mm thick screed bed or bedding layers in CM (1:4) for laying in floors finishing complete all as specified and directed.

M&L for non-skid coloured ceramic tiles joint free 7 to 8mm thick (Square/Rectangular) area of each tiles exc 0.06 Sqm but n exc 0.11 Sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match including over 15 mm thick screed bed or bedding layers in CM (1:4) for laying in floors finishing ,complete all as specified and directed.

M&L for glazed colour ceramic tiles (premium quality) of size 300X450X6-7 mm, as in vertical surface such as i.e. dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & including M&L 10mm thick backing coat in CM (1:3) complete all as specified and directed.

M&L 16 to 18 mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window cills, counter type platforms & similar nature works, machine cut, best quality as per sample, over & including 15 mm thick screeding in CM1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, providing suitable dia hole in the slab for the gas pipe, complete all as specified and as directed.

M&L for rounding edges of stone slabs one edge,such as in steps cooking platform and other similar situations complete all as specified and directed.

M & L for rendering 15mm thick in CM 1: 4 on stone masonary surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick on fair faces concrete surfaces in CM 1:3 and finished even and smooth in ceilings without using extra cement complete all as specified and directed.

M & L for rendering 15mm thick in CM 1: 6 on stone masonary surfaces finished even and smooth without using extra cement complete all as specified and directed.

M & L for preparing new plastered surfaces of walls and applying two coat of Oil Bound distemper over 2mm thick wall care putty over a coat of alkali resistant primer and complete all as specified and directed.

M & L for preparing new plastered surfaces of ceilings and applying two coat of Oil Bound distemper over 2mm thick wall care putty over a coat of alkali resistant primer and complete all as specified and directed.

M & L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

S&F mild steel work as in framed brackets of angles or tees with web and flanges for cooler stand cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S & F Pressed steel frames for doors with one or more rebates incl necessary fixing lugs, hinges, size of frame 165 x 60 mm complete all as specified and directed.

M & L for PCC (1:2:4) type B0 using 12.5mm aggregate for filling in pressed steel frame concrete shall be compressed all as specified and directed.

M&L factory Made flush shutters, 40 mm thick solid core with block board core construction as per IS 2202(part-I, 1999), both side decorative type lamination. The stiles & rails shall be with out any joint and made with non- coniferous timber hard wood (Hillock/ Mirantee/ Bosum/ Benteak) with moisture content not less than 12% as per IS. The face panel comprising of ply wood or cross band and face veneers shall be glued by hot pressed process. The over all finished thickness of face panel shall not be less than 35mm while the thickness face veneer shall not be less than 0.6 mm complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantFactory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: (a)-For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (b)- M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately.

M&L preparation of steel and steel base surfaces over 10 CM width or girth and applying two coats of synthetic enamel paint over one coate of red oxide primer complete all as specified and as directed.

S&F powder coated Anodised aluminium frame (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with aluminium section weighing 0.55Kg/m with one or more rebates or for sliding windows (2 track / 3 track), ventilators with louvers having suitable mechanism for tilting, U shaped fillets etc complete all as specified and directed.

S&F powder coated anodised aluminium door shutters (minimum thickness of powder coating 50 micron), aluminium section weighing minimum 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, 2 tower bolts, 1 mortice lock of vertical type brass 4 levers size 65mm and anodised aluminum snap beading screws etc. complete all as specified and directed.

S&F pre powder coated aluminium decogrill all as per sample fixed to aluminium framework of windows & ventilators complete all as specified and directed.

S&F powder coated anodised aluminium window shutters prepared for sliding or hanging or fixed type etc with aluminium sections weighing minimum 0.55kg/m incl necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws and also including handles, tower bolts, locks and hinges etc complete all as specified and directed by Engr-in-charge.

S&F Aluminium (Extruded section body Door closer hydraulically regulated, designation No. 3,universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S & F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S & F 150 mm long extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S & F 100 mm long medium weight, cold rolled Stainless steel Butt hinges complete all as specified and directed.

S & F Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 140 mm complete all as specified and directed.

S&F 4mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified as directed.

S & F 3mm thick Sheet glass, ordinary quality and glazing with oil putty/wooden beads in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed by Engr-in-charge.

S & F in repairs mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.00 mm with necessary fitting on steel / wooden surface complete all as specified and directed.

S&F in repairs decorative type curtain rod stainless steel finish of pipe 22 to 25 mm dia with best quality knob metal with double fitting type including stainless steel brackets (trade pattern) fixed to walls complete with two nos decorative stainless steel knobs (fincals round type with mirror optic finish) at each end , sample as approved by GE, complete all as specified and as directed

S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in replacement of single piece EWC with slim soft close seat cover complete set constellation dual flush WB constellation 5 ped constellation, EWC, cistern & lid CON dual flush, seat cover constellation, cistern fitting (water saver dual flush) etc complete all as specified and directed.

Dismantling of cast iron of AC / PVC soil, waste & vent pipe jointed in cement mortor of size 110/100mm bore, incld. All fittings, complete all as specified & directed.

All as per item No. 62.00 here-in-above, but 75mm bore.

S&F 100mm bore of cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S&F 75mm bore of cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S & F 100 mm bore of cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed on walls complete all as specified and directed.

S & F 75mm bore of cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed on walls complete all as specified and directed.

S&F 100mm bore cast iron branch pieces, single socketed Y (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F 75mm bore cast iron branch pieces, single socketed Y (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F 100mm bore cast iron Bends any radius, complete all as specified and directed.

S&F 75mm bore cast iron Bends any radius with oval access door fixed to pipe, complete all as specified and directed.

S&F 100mm bore cast iron vent cowls fixed to pipe complete all as specifed and directed.

M&L 75mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as directed

S&F in repairs 25mm stop valve, cast copper alloy with screwed down high pressure with crutch or butterfly handle both ends screwed for iron pipe or for union & fixed of 25mm dia complete all as specified and directed.

S&F in repairs angle stop valve with wall flange 15 mm bore of pipe, brass chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed including taking down old stop valve complete all as specified and directed.

S&F in repairs two way angular stop cock with wall flange, chromium plated brass, fancy type 15mm dia including taking down old stop valve complete all as specified and as directed.

S&F in repairs CP Hand Shower (Health Faucet) with 8mm dia, 1.2 Mtr long flexible tube & wall hook with N.R.V (Back flow preventer), 15 mm dia complete all as specified and directed.

S&F in repairs 15 mm bore long body bib cock with wall flange and aerator, brass chromium plated with fancy type and screwed down to 15 mm bore GI tubing or for brass ferrule including taking down old bib cock complete all as specified and directed.

S&F in repairs 15mm bore chromium plated basin mixer with 450 mm braided PVC connection pipe and provision for pop-up for mixing hot and cold water screwed down for connection pipes fixed including taking down old fittings complete all as specified and directed.

S&Fof 10 ltrs capacity PVC valve less, ISI Marked syphonic action type, flushing cistern, low level, with Anti Bacterial Knob, with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia and PVC connection, cistern colour shall be match WC colour, complete all as specified and as directed.

Dismantling water tanks exc 500 Ltr but n exc 1000 ltr and removing to store complete all as specified and directed.

S&F Rotational moulded polythene water storage tanks of 1000 ltrs capacity, white three layered (ISI marked) (Cylindrically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I with PTMT ball valve high pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

Taking up or down 25mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to storecomplete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Supply & laying of 25 mm dia CPVC pipe SDR 11 and with plain CPVC SDR 11 fittings such as bends, elbows, unions and end pieces to receive the fittings, concealed in walls/ceiling or lay in floors and fixed with solvent including cutting chases, pinning in & making good disturbed portion complete all as specified and as directed.

All as per item No.87.00 here in before but 20mm outer dia pipes.

All as per item No.87.00 here in before but 16mm outer dia pipes.

Demolition of cement concrete (unreinforced) of any description and any position not otherwise specifically provided for roof padding/roof kerb etc including dismantling of existing membrane and cement mortar and removal of debris outside MoD land complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-0 (using 12.50mm graded stone agg) over roof for making good depression/undulation and as in roof kerb rounded or chamfered on edges to match the existing , complete all as specified and directed.

M&L for rendering 20mm thick screed bed or bedding layer in CM (1:4), mixed with integral water proofing liquid all as per manufacturer's instructions over concrete surfaces finished even and smooth with out using extra cement complete all as specified and directed. (WPC shall be measured separately and paid for under respective item of schedule)

M&L for carrying out water proofing treatment using UV stable single component fibre reinforced elastomeric liquid applied waterproofing membrane having solid content of 55% formulated wih PU hybrid polymers and reinforcing acrylic fibres and having sun reflectivity Index (SRI) of 106. The application of the material should be done in three coat (6 hr gap after each coat) on the substrate, applying first self priming coat at ratio of damp proof ultra and water 3:1 then 2 undiluted coat of damp proof ultra obtaining coverage @1 ltr/10 sqft in two coats (10-12 hrs gap between each coat. The vital physical and chemical parameters shall be as under. Min elongationat break of 350%, crack bridging ability of 2.5 mm @650 microns thickness, resists positive hydrostatic pressure of up to 10 bars. The material shall be appliied with brush or roller, complete in all respect as per the direction of Engr-in charge/consultant. Also, proper surface preparation along with covingat corners is must, complete all as specified and as directed. Note : - (i) The work shall be executed by the authorized applicator of the manufacturer only. (ii) The authorized applicator of manufacturer shall be approved by GE. (iii)The color of final finish shall be decided by the GE.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified & directed.

S&F for Aluminium snap grid frame work of 605 X 605 mm panel size of pre powder coated pre fabricated GI section including hangers for false ceiling along the Walls suspended with, including S&F of 600mmx600mm size ceiling board of PVC laminated gypsum board 10-12mm thick and fixed as per manufacturers instruction as per approved sample complete all as specified and as directed.

S&F of Decooline PVC fluted wall panel design SF 742 of size 1200 x 2400mm PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing complete all as specified and as directed.

S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed.

M&L 12mm toughened glass as in hinged doors, partition automatic doors and similar work including cutting to shape, drilling holes required including all necessary fittings and floor spring hinge complete all as specified and directed.

Excavating in post holes (of similar holes) each n. exc. 0.50 cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering and removing surplus soil to a distance n. exc. 50m and making good surface complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 by using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete for fencing post, foundation for embedding the post ,as in surface chasnnels and drains etc,complete all as specified and as directed .

S & F rolled mild steel in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe 410-W(Gde E-250) quality A, complete all as specified and as directed.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base to floor, incl well compacting & laid to levels etc, complete all as specified and directed.

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any colour, design & pattern, & size/ shape, as approved by GE as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

M&L for chequered cement concrete tiles, rubber moulded 20cm x 20cm x 25 mm thick as in floor, set and jointed in neat cement slurry and pointed with coloured cement to mach the shade laid over 20mm thick screed bed in CM 1:6 complete all as specified and as directed.

S&F counter type Vitreous china wash basin white/coloured size 630X450 mm including 15mm bore swan neck pillar taps cast copper alloy chromium plated fancy type, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shank and fly nuts, screwed for iron pipe fixed with CP waste coupling 32mm and waste pipe complete all as specified and directed.

S & F Vitreous China Urinal, Half stall type, white including providing and fixing of plugs bedding against wall in CM 1:2 pointing around urinal back in cement mortar complete all as specified and directed.

M&L for 32mm bore Brass chromium plated Bottle trap for wash basins with inlet and outlet screwed for pipe or connections incl necessary packing union and cap etc complete all as specified and directed.

M&L 18 to 20 mm thick Udaipur green marble work (table rubbed & polished) as in steps, jambs, pillars, window cills, cooking platform & similar nature works, machine cut, best quality as per sample, over & including 15 mm thick screeding in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble complete all as specified and as directed.

Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed.

Taking down carefully UNSV main switch and DB's including MCBs of any size make, type and capacity and depositing at site complete all as specified and directed.as directed.

Taking down carefully UNSV Submain wiring of any size complete all as specified and directed.

M&L for (concealed) point wiring using approved colour coding as per IS red/yellow/blue/black/green for single phase circuits with multistranded copper conductor 1.5 Sqmm nominal cross sectional area single core PVC insulated and unsheathed FRLS cable 1100 volt grade, confirming ISI 694 marked with valid CML No. in and including medium grade PVC concealed conduit (including Cutting Chases and make good the distrubed surfaces as per existing finishes) of dia not less than 20 mm and conduit accessories ISI marked with valid CML No (IS 9537-1983) for roof/wall/floor etc with pressed flush metal boxes covered with inner plates & outer plates etc suitable for mounting Modular switches & sockets including PVC insulated multistranded copper conductor FRLS 1.5 Sqmm nominal cross sectional area single core FRLS cable as earth continually to common earth and connecting to earth dolly for one light point controlled by one, one way switch complete all as specified and directed. Note:- The rates of chase cutting on wall done concealed conduit & making good good the distrubed surfaces as per existing finishes and steel terminal boxes are included in the unit rates

All as per Sr. item No.114.00 here-in-above, but One fan/Exhaust fan point controlled by one way switch

All as per Sr. item No.114.00 here-in-above, but One socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch.

All as per Sr. item No.114.00 here-in-above, but One socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.

All as per Sr. item No.114.00 here-in-above, but One bell point controlled by one bell push.

All as per Sr. item No.114.00 here-in-above, but with using 2.5 Sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for independent 15 Amp point.

All as per Sr. item No.114.00 here-in-above, but with using 4 Sq mm FRLS copper wire with 4 Sqmm FRLS copper earth wire for independent 15 Amp point.

S&F Modular switch flush type single pole one way 6 Amp ISI marked complete all as specified and as directed.

S&F Modular switch flush type single pole one way 16 Amp ISI marked complete all as specified and as directed.

S&F Modular bell push, flush type, 6 Amp ISI marked complete all as specified and as directed.

S&F bell AC 230 Volts, single pole multi tune type complete all as specified and as directed.

S&F socket outlet, 3 pin, 6 Amp flush type complete all as specified and as directed.

S&F Modular socket outlet 2 in 1, 5 pin, 6 Amp, 230 Volts flush type complete all as specified and as directed.

S&F Modular socket outlet 2 in 1, 6 pin, 5 amd 16 Amp flush type, 230 Volts ISI marked complete all as specified and as directed.

S&F modular socketed stepped type electronic fan regulator flush type ISI marked complete all as specified and as directed.

S&F Ceiling rose, three terminals, bakelite body, 230 volts, complete all as specified and directed.

S&F in replacement LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including AC decorative box type with driver, holder including,copper conductor cable of suitable size from ceiling rose complete complete, 4 ft long, complete all as specified and as directed.

S&F in replacement bldg security LED Light Luminaire of 35 Watts having IP 65 protection fiting made out of pressure die cast Aluminium housing, operating Voltage 140-270 Volts with in built surge protectore, toughened glass with and including GI pipe 40 mm bracket of 1.5 m in length including drilling holes, nuts & bolts 2 coats of red oxide primer on GI pipe and fixing with wall security light on building wall connecting cable, complete all as specified and as directed.

S&F in replacement LED light fitting mirror type with high output diffuser 2 feet, 10 Watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F in repairs 2'x2' energy efficient recess mounting 36 Watt LED lumainares fixing for POP/snapgrid ceiling housing including LED lamps other accessories and necessary electric connection complete all as specified and directed.

S&F in replacement decorative, wall mounting fitting brushed nickel finish fixture with acrylic diffuser suitable with 9W LED lamp B22 base complete all as specified and directed.

Taking down and refixing/hanging only ceiling fan (M.D supply) and connecting up including provision of cable from ceiling rose or connector to fan complete all specified and directed.

Taking down and refixing only exhaust fan (M.D supply) and connecting up including provision of cable from ceiling rose or connector to fan complete all specified and directed.

S&F Vertical Distribution Board, double door, suitable for 'A' frame FP MCCB 100A made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP43 & IK09 protection, TPN 4 way, 415 Volts with bus bar rating 300 Amps, dust and vermin proof, suitable for incorporation of MCB's and MCCB etc and making all necessary connections, duly flush of wall surface complete all specified and directed. Note: MCCB and MCB will be measured and paid separately under respective items.

S&F MCCB, A frame, thermal adjustable magnetic setting, Ics=75% 16kA, 415V, 100 Amp, 4 pole MCCB with overload and short circuit protection complete all as specified and directed.

S&F MCB, B type curve, 10kA, 63 Amp, SPN with over load and short circuit protection complete all specified and directed.

S&F MCB, B type curve, 10kA, 6 to 32 Amp, single pole with over load and short circuit protection complete all specified and directed.

S&F sheet metal enclosures 240 Volts with suitable rated bus bar for double door IP-43 DB's suitable for one MCB SPN as incoming and 10 MCB SP as outgoing SPN 12 way complete all specified and directed.

M&L for sub main wiring with 2 run of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn into separate concealed medium grade, ISI marked, non metallic PVC conduit 25mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc with and incl cutting chasing and making good of disturbed surface of wall/floor/ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note: Two runs of 6 sqmm and one runs of 6 sqmm (earth wire) including one run of PVC conduit shall be measured as one length incl making good the disturbed surfaces for the purpose of measurement.

M&L for sub main wiring with 2 run of 4 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn into separate concealed medium grade, ISI marked, non metallic PVC conduit 25mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc with and incl cutting chasing and making good of disturbed surface of wall/floor/ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note: Two runs of 4 sqmm and one runs of 4 sqmm (earth wire) including one run of PVC conduit shall be measured as one length incl making good the disturbed surfaces for the purpose of measurement.

M&L in replacement Earthing complete with galvanised steel earth plate electrode 60 x x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) wih top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 SSR Part-I 2009 and specified or indicated including excavation and earthwork in any type of soil PCC 1:3:6 type C1 in chamber, precast RCC 50mm thick in cement concrete 1:2:4 type B1, reinforced with welded steel wire fabric or XPM (Weight not less than 4.00 mm dia with cast iron frame, funnel with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm bore medium grade GI protection pipe, test point etc complete all as specified and directed. Note : (i) Item includes the cost of 7.5 metre GI pipe for protection of earth lead. (ii) Item includes the cost of 7.5 metre GI earth lead.

Supply, laying testing of LT UG XLPE in trenches / saddle clamping on wall (as per site requirement) through protection pipe insulated, armoured, heavy duty electric cable, aluminium coductor, 1100 V grade, cross sectional area 50 sqmm 3.5 core, complete all as directed by Engr-in-charge. Note : Earth work and brick work measured and paid separately

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in hard/dense/soft / loose soil complete all as specified and as directed.

Supply and laying of sand for sand cushioning for cable protection in trenches including punning down of sand layer all as specified and directed. Note :- Punned thickness shall only be measured and paid.

Supply and laying unreinforced Precast concrete cable cover, class LV, type 1, flat size 300 mm x 180 mm x 40mm, complete all as specified and directed.

S&F in replacement of GI tubing , light grade of 40mm bore with fittings as in road crossings for cable protection complete all as specified and as directed.

S&F of sheet metal enclosure SPN with a two pin earth plug and socket with metal cladd top and one MCB, SP 20 Amps capacity complete all as specified and directed.

Taking down old servicable split AC complete (inner and outer) incl voltage stabilizer any size and capacity and take in safe custody and refix in same position complete all as specified and as directed.

M&L for road cutting (not more than 3.5 mtr in width of road) and excavation upto 60cm below ground level and laying of 5 RM protection 40mm dia GI pipe of light grade and make good disturbed surface by PCC 1:4:8 (nominal mix), type D2, using 40mm graded crushed stone aggregate complete all as specified and as directed.

Supply and Install desert cooler electric driven (single phase) three speed having nominal air flow capacity 5000 CFM per hour, with propeller ISI cooler fan motor copper winding single phase fitted with / having aluminium blade of minimum size 500mm, submersible pump, Max power consumption of 325 Watts. Cooler body made out from 20 gauge mild steel galvanized iron sheet & water tank made out of 18 SWG, having 60 Ltr minimum including three louvers with wool pad, flexible PVC distribution pipes and 3 way junction all as directed by Engr-in-charge and of standard make as approved by GE. Note : (1) Three speed switch ISI marked rotary type for propeller fan and one way switch pump with separate control. The switches shall have marking off Low, Medium & High. (2) Float Valve on water supply connection shall be deemed to be included in unit rate quoted. (3) PVC connection pipe including fastners, nuts, washers and reducer, tee, elbow etc (GI fittings) for making connection of water supply to desert coolers.

M&L for stand, flush to wall for desert cooler, fabricated out of MS angle iron 40mm x 40mm x 6mm, 1.20 mtr long bend to shape as top size 600mm x 600mm, duly welded with two members to tie vertical support, including painting two coats of synthetic enamel paint over a coat of red oxide primer including M&L for steel rack bolts/fasteners, 100mm long, 12mm dia - 4 Nos for fixing stand complete all as specified and as directed.

M&L for writing letters in black colour paint 40mm width :- (a) Manufacturer Srl No (b) Date set to work (c) Initial cost (d) PRB Page No (e) Location etc complete all as specified and as directed.

Note:- (i)- Qty's have been clubbed from 02 Nos sanction Job's, whose details as per appx NOTE:- (i)- The contract sum shall be arrived at after duducting amount of schedule of "Credit" from the Total quoted amount