C_O Residential Accomodation for Executive Engineer IPH Division Karsog under IPH Circle Sundernagar Tehsil Karsog Distt Mandi HP

Amount

Excavation in foundation and trenches in earth work upto all depth in all kinds of soil such as pick work jumper work,blasting work,chiselling of soft /hard rock where blasting is prohibited in all leads and lifts and including trimming of sides levelling of bed to correct grade stacking the excavated soil in 15cm.layers when required into plinth sides of foundation including consolidating each deposited layer by ramming and watering and then disposing oof all surplus excavated soil as directed in all leads and lifts and soring/strutting timbering and dewatering where ever required to the entire satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1:4:8 (1 cement : 4 sand : 8 graded stone aggregate 40 mm nominal size ) and curing complete excluding cost of form work in foundation and plinth.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for insitu- reinforcement concrete and plain concrete work in:-

Foundation footing bases of columns etc and mass concrete.

Columns, pillars, post and struts.Square, rectangular or polygonal in plan.

Beam, cantilever, girders and lintels.i) Sides and soffits of beam, beam haunching, cantilever, bressumers and lintels not exceeding 1 mtr. In depth in all heights from floor.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like.i) Floors etc. up to 200mm in thickness.

Edges of slab and breaks in floors and walls under 20 cm wide.

Stair cases with sloping or stepped soffits excluding landings.

Providing & Laying cement concrete work 1:11/2: 3 (1 cement : 11/2 sand : 3 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:-

Foundation footing bases of columns etc and mass concrete.

Colunms pillars posts and struts upto floor two level.

Lintels, beams girders bressumers and cantilevers upto floor two level.

Providing and laying cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) and curing complete excluding the cost of form work and reinforcement in:-

Suspended floors, roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilivers up to floor two level.

Stair cases (Except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto floor two level.

Providing mild steel / Tor steel reinforcement for RCC work including bending binding and placing in position complete upto floor two level. Tor Steel

Provdiing and laying 20 cm thick composit stone masonry with stone masonry with stone facing of chisel dressed stone one line dressed in cement mortar 1:6 (1 cement :snnd) and concrete backing with cement concrete 1:3:6 (1cement :3and :6 graded stone aggregate 20 mm norinal size) on inner face of walls including cenrting shuttering and propping complte upto floor two level.

Brick work using common burunt clay building bricks in super structure above plinth level upto floor two level in cement mortor 1:6 (1 cement : 6 sand) (Ist class brick)

Half bricks masonry in common burnt clay building bricks in cement mortar 1:4 (1cement : 4 sand) (Ist class brick)

Providing wood work in frames of doors, windows, clerestory windows and other frames wrought, framed and fixed in position. (Ist class deodar wood)

Providing and Fixing panneled glazed or panelled and glazed shutters for doors, windows and clerestory windows,including black enamelled iron butt hinges with necessary screws. 40 mm thick. (Ist class deodar wood)

Providing and Fixing wire gauge shutters using galvenised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors, windows & clearstory windows i/c bright finished black iron enamelled hinges with necessary screws 40 mm thick (Ist class deodar wood)

Providing & Fixing M.S. grills of required pattern in wooden frame of window etc.with M.S. flats, square or round barswith round headedbolts and nuts by screws (ornamental grills).

6mm cement plaster to ceiling in CM 1:3 ( 1Cement :3 Sand)

15 mm cement plaster in single coat on rough side of brick/concrete stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 (1 cement: 6 sand)

Stone soling under floor.

Providing and laying cement concrete 1:6:12 (1cement:6 sand: 12 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth.

Cement concrete flooring 1:2:4 (1 cement : 2 sand :4 graded stone aggregate 20 mm nominal size) laid in one layer finished with a floating of neat cement.40 mm thick

Cement plaster skirting (upto 30 cm height) with cement mortor 1:3 (1 cement : 3 sand) finished with a floating coat of neat cement including rounding of junction with floor 20 mm thick.

Providing and laying granite stone in flooring 20mm (average) thickness base of cement mortor 1:3 (1cement : 3sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete. 20 mm thick.

Providing and Fixing antiskid water proof stain and impact resistent heavy duty vetrified tiles Nitco or equivelent (600 X 600 X 10 mm) manufactured of approved shade and colour treads of steps laid on a bed of 12 mm thick cement mortor 1:3 (1cement : 3 sand) finished with flush pointing in white cement mixed with pigment ofrequired shade to match the shade of tiles complete.

Providing and laying spartic ceremic tiles 5.5 mm thick in flooring (300 X 300 mm size) treads of steps laid on a bed of 12 mm thick cement mortor 1:3 (1cement : 3 sand) finished with flush pointing in white cement.

Coloured glazed tiles 6 mm thick in skirting risers of steps and dedo12 mm thick cement mortar 1:3 (1 cement : 3 sand) and jointed with cement slurry in all leads and lifts.

Providing and Laying clay tiles (Khaprail) over mumty roots grouted with cement mortor 1:3 (1cement : 3 sand) over a 12 mm layer of cement mortor 1:3 ( 1 cement : 3 sand) and finished neat in all leads and lifts.

Providing and Fixing 19mm thick water proof commercial board in shelves/box for cup board with butt joints & Fixing with nails & screws etc. complete.

Providing and Fixing 19mm thick Commercial Board water proof shutters for cup boards i/c Fixing with nickel plated piano hinges with screws etc. complete.

Providing and Fixing 4mm thick burl ply of standard quality and of approved shade & design wall lining i/c Fixing with approved adhesive, butt jointing and nails & screws complete (Base frame work to be measured & paid for separately)

Providing and Fixing 1.00mm thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete.

Providing and Fixing square edges cover fillets (beading) 19 mm x 6 mm section i/c mitring at junctions with wood screws and nails complete. Ist class Indian Teak Wood.

Providing 40x3 mm iron hold fast 40 cm long including Fixing to frame with 10 cm da bolts nuts and wooden pluges and embencing in C.C. block 30x10x15 cm 1:3:6 ( 1 cement:3 sand: 6 graded stone aggregate 20 mm nominal size).

Providing and Fixing bright finished brass sliding door bolts with bolts and nuts screws etc. complete.

Providing and Fixing bright finished brass tower bolts ( barel type) wqith screws etc. complete.

Providing and Fixing bright finished brass handles with necessary screws etc. complete.

Providing and Fixing bright finishaed hard drawn Hooks and Eyes 250 mm .

Providing and Fixing 75 mm x 60 mm rounded hand rails in straight length complete in 1st class indian teak wood.

Providing and Fixing 12 mm thick 150 mm wide pelmet with 25 mm diametre wooden curtain roads and brackets including Fixing 25x3 mm M.S flat at 10 cm long and plugs etc. complete.!st class Deodar wood.

Steel work welded in built up sections, trusses and framed work including cutting hoisting Fixing in position and applying a priming coat of red lead paint :- In beams joists channels ,angles, tee, flats with connection plates or angle cleats as in main and cross beems, hip and jack rafters, purlins connected to common rafters and the like.

Providing & Fixing 0.60mm thick preprited steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coatig including Fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accessories as required as per the direction of Engineer-in-charge.

Providing ridges or hips 60 cm over all in plain with galvanised iron preprited steel Sheet fixed J or L hooks bolts and nuts 8mm dia G.I Limpet and bitumen washers complete 0.60 mm thick sheet.

Providing and Fixing 15 cm wide 45 cm over all semicircular with iron plain G.I. sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary connection with rain water pipe complete as per design. 0.80 mm thick sheet.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1cement:3sand:6 graded stone aggregate 20 mm nominal size.

Proving under layer for plinth protection of 75 mm thick (unconsolidated) bed dry brick/stoneAggregated 40 mm nominal size will rammed with rammed and consolidated and grouted with fine sand including preparation of ground.

Constructing course rubble hammer dessed "U" shape open surface drain with side wall 15x22 cm in cement mortor 1:6 (1cement : 6 sand) and inside plastering with cement plaster 1:3 (1cement : 3 sand) including earth work and laayng 10 cm cement concrete in 1:5:10 (1 cement :5 sand : 10 graded stone aggregate 40 mm nonminal size) and 7.5 cm cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete .

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface.

Applying one coat for wood preservetive on previously treated wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter,sand papering and knotting.

Applying priming coat over new wood and wood based surfaces after and inciuding preparing the suface be thoroughly cleaning oil grease dirt and othr foreign sand papering and knotting Readymixed paint brushing wood primer pink.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint to give an even shade including cleaningthe surface of dirt, dust and other foreign matters sand papering and stopping with enamel paint other than white.

Painting two coats (excluding priming coat) over new steel and other metal surfaces,with enamel paint to give an even shade including cleaningthe surface of dirt ,dust and other foreign matters sand papering and stopping with enamel paint other than white.

Providing and laying heavy duty precast cement concrete inter locking paver blocks vibro compacted upto M-50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25 mm thick average thickness of cement mortor 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing and polishing complete (Sub base concrete floor to be paid for 60 mm thick inter locking blocks).

ELECTRICAL WIRING :-

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. Group "C"

Wiring for light plug with 2x1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Supplying & Fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required:-

4 modules (140mmx78mmx50mm)

6 modules (205mmx78mmx50mm)

8 modules (120mmx135mmx60mm)

12 modules (205mmx135mmx60mm)

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2 x 1.50 Sq. mm.

2 x 2.50 Sq. mm.

2 x 4.00 Sq. mm.

Wiring for circuit / sub-main with 4x6 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.6 Sq.mm. (4x6+2x6) HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Wiring for circuit / sub-main with 4x10 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.10 Sq.mm. (4x10+2x10) HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

S.P. 5/ 6 Amps one way Modular switch.

5 pin, 5/ 6 Amps Modular socket outlet.

Bell push, Modular.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

S.P. 15/ 16 Amps one way Modular switch.

6 pin,15/16 Amps Modular socket outlet.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

TV. Socket outlet, modular.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

Telephone socket outlet, Modular.

Supplying and Fixing ceiling rose on the existing junction box / wooden block including connections etc. as required.

Supplying and Fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:-

Double door-12 way

Supplying and Fixing following rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required.

63 Amps Cat-A

Supplying and Fixing sheet metal bus-bar chamber suitable for 200 Amp. 415 volts capacity with 4 No. copper strip bus-bars each of length 450 mm & cross-sectional area (25.4 mm x 4.75 mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (530 mm x 450 mm x 150 mm) nominal with all accessories including connections, earthing the body etc. as required.

Providing and Fixing TP&N switch disconnector fuse unit cubical type, 415/500 volts with 3 No. HBC/HRC fuses, in sheet steel enclosure including drilling holes on the board, connections, earthing the body etc. as required.

100 Amp. Category-A

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required.

Single pole & neutral. Cat-B.

Supplying and erection of wall mounted metal boards for switch gear mounting of suitable size, with permissible variation in size of plus minus 5mm, welded frame work made of M.S. angle iron 35 mm x 35 mm x 6 mm thick duly welded complete with 2.80mm thick M.S. sheet fixed with hinges as open able front, complete with locking arrangement including painting and bonding to the existing earth as required.

Supplying and Fixing following rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required.

40 Amps. Cat-B.

Supplying and Fixing 20 Amps, 240 volts, SPN industrial socket outlet, 2-pole & earth, metal enclosed plug top, sheet steel enclosure, suitable to accommodate a 20 Amp SPN-MCB/DP, on surface or in recess, with chained metal cover for the socket outlet, complete with connections, testing and commissioning etc. as required.

Earthing with copper earth plate 600 mmx600 mmx 3 mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required.

Providing and Fixing M.V.danger notice plate of 200 mm x 150 mm made of mild steel at least 2 mm thick, and vitreous enameled white on both sides and with inscription in signal red color on front side as required.

Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and Fixing of Non-return valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. as required.

25 Liter capacity water heater (Cat-A)

10 Liter capacity water heater (Cat-A)

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and Fixing phenolic laminated sheet cover on the fan box and earthing etc. as required.

Ceiling Fan 1400 mm sweep, Category-A

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required.

Exhaust Fan, Light duty, (Domestic) 225 mm sweep

Providing and Fixing of Syska make LED Tube Fixture 18 watt complete in all respect in all leads and lifts.

Supplying and Fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required:-

Supplying and drawing co-axial TV cable,RG-6 grade,0.7mm (75 Ohms) copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed, steel / PVC conduit as required.

Supplying and Fixing bakelite batten/angle holder including connections etc. as required.

Supplying and Fixing of integral CFL Post Top Lantern of following capacity, cast aluminium spigot, spun aluminium canopy, opal acrylic diffuser, complete with all accessories but excluding CFL lamp including making connections, testing etc. as required.

Gate post top lantern - CFL 26 watt.

Spplying and Fixing of split type air conditioner Blue Star / LG / Onida Whirlpool / Lioyd / Samsung make having two stars features auto clean filter four way swing all copper pipes including making provision of draining of back moisture water tharough GI pipe 20 mm dia electronic voltage stabilizer, cutting holes for conduits in wall, unit bracket set fixed on outer wall complete as required. 1.50 Tonne capacity.

WATER SUPPLY AND SANITARY FITTINGS :-

Providing and Fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including Fixing with approved adhesive etc. complete.

75 mm dia

110 mm dia

Providing and Fixing PVC plain bend ISI marked including Fixing with approved etc. complete.

75 mm dia

110 mm dia

Providing and Fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including Fixing with approved etc. complete.

75 mm dia

110 mm dia

Providing and Fixing PVC collars ISI marked including Fixing with approved etc. complete.

75 mm dia

110 mm dia

Providing and Fixing PVC singal equal branch plain ISI marked including Fixing with approved etc. complete.

75 mm dia

110 mm dia

Providing and Fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including Fixing with approved etc. complete.

75 mm dia

110 mm dia

Providing and Fixing PVC floor trap ISI marked of self cleaning design including Fixing with approved, cost of cutting and making good the wall and floors etc. complete.

Providing and Fixing vitreous China wash, down water closet (EuropeanType WC pan) with integral "P" or "S" trap including jointing the trap with soil pipe in cement mortar 1:3 (1 cement : 3 sand) ( seat and cover to be measured and paid for seperately) : Angle Indian (Universal Closet) in all leads and lifts.

One piece WC for toilet including cistern & seat cover cera make CRUSE.

Two piece WC for other toilet CERA make CRUSE.

Providing and Fixing white solid type plastic sheet and cover for wash down water closet with CP brass hinges and rubber buffers.

Two piece WC for other toilet CERA make CRUSE.

Providing and Fixing 10.00 liters Concealed cistern with a pair of C.I. or mild steel brackets, complete with fitting such as lead valve less syphon, 15 mm nominal size brass ball valve with polythene float, C.P. Brass handle, Unions and couplings for connections with inlet, outlet and couplings for connections with inlet, outlet and over flow pipes, 40 mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) in all leads and lifts.

Two piece WC for other toilet CERA make CRUSE.

Providing & Fixing viterious china wash basin with single hole for pillar tap with C.I. or M.S. bracket painted white including cutting hole including good the same excluding fitting Cera sanitary work (cornet) white Flat back 630 mm x 450 mm.

Providing and Fixing viterious china padestral for wash basin complete recessed at the basic for reception of pipe and fittings Cera sanitary work (carnet) white (Viterious China in White Colour)

Providing and Fixing M.I. Union for wash basin or sink 32 mm dia.

Providing and Fixing C.P. brass waste and plug for glazed ware sinks, basins etc. with long screwed shank and fly nut and fixed to steel pipe including vulcanite plug, brass chain and stud 32 mm nominal bore.

Providing and Fixing 600 mm x 450 mm bevelled edge mirror of superior glass marked on 6mm thick AC sheet or plywood sheet and fixed to wooden plug with CP brass screws and washer.

Providing and Fixing CP Brass towel rail complete with CP Brass brackets fixed to wooden plug with CP Brass screws 600 mm x 20 mm.

Providing and Fixing 600 mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws.

Providing and Fixing Toilet paper holder C.P. brass.

Providing and Fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. brass screws.

Providing and Fixing Tooth brush and Tumbler holder (Viterious China)

Providing and Fixing C.P. Brass Shower Rose with 15 mm to 20 mm inlet 100 mm dia.

Providing and Fixing brass bib tap (Superior or heavy type) 15 mm dia long nose.

Providing and Fixing brass bib tap (Superior or heavy type) 15 mm dia short body.

Providing and Fixing C.P. brass angle valve 15 mm without Nuts and pipe.

Providing and Fixing C.P. concealed stop cock 15 mm without Nuts and pipe.

Providing and Fixing one hole basin mixing Faucet.

Providing and Fixing P.V.C. connection with brass unions 300 / 450 mm length 15 mm nominal bore.

Providing and Fixing 100 mm dia chromium plated grating of superior quality for floor, gully or Nahni trap.

Providing and Fixing PTMT Jet spray of approved quality and colour with one meter tube.

Providing and Fixing of C.P. Towel ring of superior quality.

Providing and Fixing of C.P. towel rack 600 mm x 250 mm of superior quality.

Providing and Fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M. S. brackets painted white including cutting holes and making good the same but excluding fitting 610 x 460 mm with bowl depth 200 mm.

Providing and Fixing to wall ceiling and floor galvenised mild steel tubes (light grade) tube fittings and clamps including making good the wall, ceiling and floor in all leads and lifts.

25 mm nominal bore

Providing and Fixing brass full way valve with wheel of 25 mm dia (Heavy Duty) complete in all respect in all leads and lifts.

Providing and Fixing to wall ceiling and floor CPVC Pipe SDR 11 class - 1 (HSN Code : 3917) and clamps including making good the wall, ceiling and floor complete in all respect in all leads and lifts.

15 mm nominal bore

20 mm nominal bore

Providing and Fixing CPVC Coupler (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

15 mm nominal bore

20 mm nominal bore

Providing and Fixing CPVC Elbow (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

15 mm nominal bore

20 mm nominal bore

Providing and Fixing CPVC Tee (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

15 mm nominal bore

20 mm nominal bore

Providing and Fixing CPVC Reducing Coupler (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

i) 20x15 mm dia

Providing and Fixing CPVC Reducing Tee (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

i) 20x15 mm dia

Providing and Fixing CPVC Reducing Tee (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

i) 15 mm dia

ii) 20 mm dia

Providing and Fixing CPVC Union (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

i) 15 mm dia

ii) 20 mm dia

Providing and Fixing CPVC Union (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

i) 15 mm dia

i)20 mm dia

Providing and Fixing CPVC Ball valve (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

ii) 15 mm dia

i) 20 mm dia

Providing and Fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete in all leads and lifts.

Providing and Fixing of PVC water storage tank sintex having of capacity 1000 liters with necessary fittings including over flow pipes, scour pipes etc. inlet and outlet and inside paint of required size for inlet or outlet and inside paint of approved quality complete including hoisting complete in all respects.

Construction of manhole with RCC top slab in 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40 mm nominal size) in side plastering 15 mm thick with cement mortar 1:3 (1cement:3 sand) finished with a floating coat of neat cement and making channel in cement concrete 1:2:4 (1cement:2 sand:4 graded stone aggregate 20 mm nominal size) including curing complete.

i) In side size 800 mm x 800 mm x 500 mm deep excluding CI cover with frame (light duty single seal pattern - 1) 455 mm x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg. (Weight of cover 23 kg and weight of frame 15 kg)

With 200 mm thick walls of brick masonry using common burunt clay building bricks in cement mortor 1:3 (1cement : 3 sand)

Providing and Fixing stoneware gully trap grade "A" complete with C.I. grating, brick masonry chamber in cement mortor 1:5 and water tight C.I. cover with frame of 300 mm x 300 mm size (inside) the weight of cover to be not less than 4.53 kg and frame to be not less than 2.72 kg. (Sqaure Mouth traps 100 mm x 100 mm size P type)

Gurvaksh Singh