REPAIR/ REPLACEMENT OF OLD STEEL BROKEN WINDOW WITH ALUMINIUM WINDOW INCLUDING DOOR, SHUTTERS IN OR / JCO ACCN OF UMRAO VIHAR UNDER GE (S) BINNAGURI

Amount

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area exe 1.5 sqm but n.exe 4 sqm each complete all as specified.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area n.exe 1.5 sqm each complete all as specified.

Taking down shutters area exe 1 sqm and n.exe 2 sqm each complete all as specified.

Taking down shutters area n. exe 1 sqm each complete all as specified.

S&F pressed steel frames of size 125X60mm minimum 1 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified.

S&F pressed steel frames of size 105X60mm minimum 1 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified.

M&L for PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in holdfast block, coping, bedblock etc. and including necessary use and waste of formwork complete all as specified.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides etc complete all as specified.

S&F factory made wire gauzed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails MS. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; the wire gauze shall be wrapped on an additional square 8mm MS. solid tube and this tube shall be welded to MS. tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS. tubes for top & bottom rails. MS. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

S&F aluminium anodized barrel tower bolts, extruded section 200mm long complete all as specified.

S&F aluminium anodized handles, D type, 150mm size complete all as specified.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified.

S&F stainless steel butt hinges medium weight 100mm size for PVC door complete all as specified.

S&F stainless steel butt hinges medium weight 150mm size for wooden door complete all as specified.

S&F aluminium anodized barrel tower bolts, extruded section 150mm long complete all as specified.

S&F aluminium anodized handles, D type, 125mm size complete all as specified.

S&F powder coated aluminium sliding window sliding 3 track, two shutter glazed with and including 4mm thick plain sheet glass and one shutter with stainless steel wire cloth 0.36 mm dia of wire and average width of aperture 1.40 mm fixed with stainless steel wire stapples rubber gasket stopper, handle 100mm, frame of section 100mm X 45mm X 1.55mm and of shutter of section 40mmX 20mm X 1.55mm including taking down of old steel window & making good disturbance with CM (1:3) complete all as specified and directed.

M&L for fabrication and fixing of powder coated aluminium door shutter fixed with rubber gasket, stopper, cleats, handles etc complete for aluminium frame of size 101.6mm x 44.45mm x 2mm and section of bottom and top rail of section 114mm x 44.45mm x 2mm thick and and lock rail shutter frame of 83mm x 44.45mm x 2 mm with and including panels of 5.5 mm thick plain/frosted float glass, and with anodised aluminium snap beading of size 18.2mm x 16.66mm scred for fixing fully including double action door spring hydraulically regulated made up of 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and all necessary fittinngsand EPDM rubber packing each shutter shall be provided with two decorative type aluminium disc handle of 150 mm dia per shutter, 1 No heavy duty door shutter 1 No 200mm long aluminium tower bolt per shutter including taking down old onecomplete all as specified

S&F Powder coated aluminium louvered ventilators of size n exc 0.50 Sqm area with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazing cleats, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings and 5.5mm thick tinted glass fixed in panels with suitable locking arrangements including taking down of old existing steel ventilator and making good disturbed surface of wall complete all as specified.

Supply & fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

M&L for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riv-eted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 390 Gde E-165 including dismantling old wrought iron or mild steel complete all as directed.

S&F in replacement for CP curtain rod 25mm dia and with brackets, knobs etc complete, the type portion and size of curtain rod shall be approved by Engr-in-Charge.

Supply and fix in repair stainless steel kitchen plate rack of size 31"x30"x10" and 1 mm thick complete all as specified. (Make- Pryag/Nirali)

Taking down of cement plaster on brick (or) concrete wall etc including racking out joints haking for key scrubbing down with water etc complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brickwork with subclass ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified.

M&L for brickwork with sub class 'B' old size bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement morter 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of walls in cement morter 1:4 with water proofing compound finished even and smooth without using extra cement complete all as specified and as directed. (Note : WPC shall be measured and paid separetely)

M&L for rendering 5mm thick in CM (1:3) on ceiling, soffits of slabs, chajjas, columns and beams etc and finished the plastered surface even and smooth without using extra cement complete all as specified.

M&L for preparing newly plastered or unplastered surface of ceiling and applying three coats of white washing complete all as specified and directed.

M&L for preparation on new plastered surfaces of wall and applying two coats of exterior grade weather coat paint over a coat of primer complete all as specified and directed.

M&L for preparing new plastered surfaces of wall with 1 mm thick (avg thickness) wall care putty and applying two coat of distemper oil emulsion over a coat of primer complete all as specified.

M&L for preparation of new wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed..

M&L for preparation of old treated surfaces of walls and applying two coats of white wash complete all as specified and directed.

M&L for complete removal of old decorated surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, etc and applying two coats of exterior grade weather coat paint over a coat of primer etc complete all as specified and directed.

M&L for preparing old plastered surfaces of wall and applying two coat of distemper oil emulsion over a coat of primer complete all as specified.

M&L for preparing old painted wooden surfaces of any description not otherwise described for over 10 cm width or girth and applying one coat of synthetic ennamel paint complete all as specified and directed.

M&L for preparing old painted steel surfaces of any description not otherwise described for over 10 cm width or girth and applying one coat of synthetic ennamel paint complete all as specified and directed.

Dismantling floor hearth or wall tiling of any description, size and thickness including cement mortor bedding, removing rubbish off the premises etc complete all as directed.

M&L for glazed ceramic coloured joint free tiles in vertical surface 450X 350X 7mm thick with and including 10mm thick CM 1:4 backing coat, set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) laid in floors area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, etc. with and including 15mm thick screed bed in CM 1:6 , set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as directed.

Ditto all as per serial item No. 45.00 described here-in-before but in skirting fixed over 10mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for non-skid ceramic coloured tiles 8 mm thick (square/ rectangular) polished area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc. with and including 15mm thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as directed.

Ditto all as per serial item No. 47.00 described here-in-before but in skirting fixed over 10mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for machine pressed, pre-polished and chemically treated, smooth finished, exterior graded coloured cement concrete Chequered tiles 30cm x 30cm x 22-25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar.

M&L for 16-18 mm thick Granite work (table rubbed and polished) in decorative shelves, steps, pillers, jambs, coocking plateform etc laid over 15mm screed bed in CM (1:6) with chemfering of edge including pointing in white cement with pigment to match with shade of granite including grinding & mirror polishing complete all as specified

M&L for providing & fixing factory made solid PVC cup board frame of size 50mm x 47mm with a wall thickness of 5mm made out of extruded 5 mm thick prelam/plain colour PVC sheet reinforced with 19mm x 19mm MS square tube of 19 gauge thickness throughout the frame and metre cut at two corners and jointed with 2 Nos of 150mm long brackets of 15mm x 15mm MS square tubes. The door frame shall be fixed to the wall using 100mm long MS screws through the frame by using PVC fasteners. A minium 4 Nos of screws to be provided for each vertical memberand minium 2 Nos of screws to be provided to the horizontal mmember etc. incl dismantling of existing cupboard frame complete all as specified.

M&L for providing & fixing factory made solid PVC cup board shutter (Flush type) of 24 mm thick made from co-extruded 3 layer regid PVC foam sheet (single extruded) with density not less than 600kg/cbm outer layer (0.8-1mm) thick should be of rigid PVC with density of not less than 1400kg/cbm manufactured byan ISO 9001-2015 certfied company. Door should be water proof, termite proof, fire retardant and having good screw holding capacity incl taking down the ext cupboard shutter complete all as specified

S&F in repair factory made PVC shelf/ partitation of required size consisting of 20mm thick solid PVC sandwich with 1mm thick plain PVC sheet on both sides suitably fixed in complete all as specified and directed

BBKundu (BID ID -3487680)

M/S DELTA ENGINEERS & CO (BID ID -3487733)